Technical introduction
Use MRL Observation Lift
450kg
1.0
1075 825 Operation Type JXW
Control Type VVVF
695 695
Traction ratio 2:1
Traction machine FUJI
Motor power(kw) 3.2
400
Hoistway depth2000
Traction sheave
500 Door opening Centre opening
1300
Max. floors
Overhead height
150
Max. travelling 90m
500
500
600
1300
Min. floor space
250
a3
a4
400
1100(W)X1100(D
a2 Car net size
200
200
Car outer size 1150(W)X1265(D
500
720
Door net size 800(W)X2100(H
320
r
Car net height 2200
Top floor height 4000
Pit depth 1600
Travelling height
Hoistwat width1900
Floor Stop Door 5/5/5
Power supply(V) 220V AC 60Hz 3P5L
Lighting supply(V) 220V AC 1KVA/set
Top floor load point stress (N)
R1 40000 R2
Guide rail stress(N)
FyCar FyCWT
Door lintel(masonryconcrete FxCar FxCWT
structure shaft must add door
lintel )
400
100 100
Controller reserved hole
Notes
HH1
1.Brackets(include guide rail brackets,landing door door header brackets,sill
brackets etc.),use reinforced concrete structure at installation point,if useing
other structure please contact with FUJIHD.Hoistway flatness:front wall side
wall,back wall+50/mm
1200
2.The reaction force on hoistway pit bearing drawing,if there is room people can
150
hoistway depth come in under pit,please contact with FUJIHD.Keep pit dry,clean,without
waterlogging.
3.The hoistway is only for elevator using,anything unnecessary(eg.
pipes,cables,etc.)can not be installed in the hoistway.The hoistway cann't allow
a1
400 person to get in.
500 400
a
500
400
200 400
1050
1500
5.Dynamic&lighting supply should be ste at the bottom of control cabinet which
101000N
81000N
is on the top floor.Electronic lineuse at least 1.5m more for the elevator
350
400 320 installatin.
7.Min. floor space is 2.55m,if the space of nearby two floor is over 11m,safety
300
door is needed.The min.size is W350xH1800 by user,details refer to(GB7588-2003
5.2.2)
250
1075 825 8.Requirements of way size which is on the hoistway side of top floor:width at
841 least 700mm,height at least 2000mm.
9. Due to the need of five-way intercall system,atelephone line should be
set from machine room to reception room.The line should be no more than 200m.
10.If traction bearing beam set in bearing wall,it should over wall thickness
centre at least 20mm.
740
11.The min. thickness of concrete wall:150mm,the min. thickness of brick
Hoistway depth2000
wall:200mm.
12.After installation,the backfill and repair work of door frame,three side wall
695 695 and other installation holes should be by user.
Car depth1100
13.This layout only use for layout confirmation when signcontract,during
installation use the layout with "elevator installation special"stamp as right
400
736
one.
405 200
Articles MIin size
1240
520
75
85 30
500
500 400
275
Hengda Fuji Elevator Co., Ltd.
Floor Floor height1 Floor height2
46/F 1075 825
45/F 841
44/F
500
500
43/F
1300
42/F
Hoistway depth2000
41/F
500
40/F
39/F
250
38/F
736
37/F
36/F
35/F
Cabin
520
34/F
33/F
32/F
31/F
30/F
29/F
28/F
27/F
26/F
25/F
250
24/F
23/F
22/F
21/F
20/F
250
19/F
18/F
17/F
16/F
250
400
15/F
14/F
500
400
13/F
12/F
11/F
10/F
800
800
9/F
8/F
7/F 8mm
800
800
6/F
1075 825
5/F
845
4/F 4000
500 400
3/F 2975
2/F 2975
1/F 2975
PB/F 3150
Hoistway depth2000
-2/F
-3/F
600
Pit 1600
200
720
Hoistwat width1900
Hengda Fuji Elevator Co., Ltd.
