Distributed by:

www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.

Jameco Part Number 1549214

 HCPL-2201, HCPL-2202, HCPL-2211,HCPL-2212,
HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211,
HCNW2201, HCNW2211
Very High CMR, Wide VCC Logic Gate Optocouplers

Data Sheet
Lead (Pb) Free
RoHS 6 fully
compliant
RoHS 6 fully compliant options available;
-xxxE denotes a lead-free product

Description Features
The HCPL-22XX, HCPL-02XX, and HCNW22XX are optical- • 10 kV/µs minimum Common Mode Rejection
ly-coupled logic gates. The HCPL‑22XX, and HCPL-02XX (CMR) at VCM = 1000 V (HCPL-2211/2212/0211/2232,
contain a GaAsP LED while the HCNW22XX contains an HCNW2211)
AlGaAs LED. The detectors have totem pole output stag- • Wide operating VCC range: 4.5 to 20 Volts
es and optical receiver input stages with built-in Schmitt • 300 ns propagation delay guaranteed over the full
triggers to provide logic-compatible waveforms, eliminat­ temperature range
ing the need for additional waveshaping.
• 5 Mbd typical signal rate
A superior internal shield on the HCPL-2211/12, HCPL- • Low input current (1.6 mA to 1.8 mA)
0211, HCPL-2232 and HCNW2211 guarantees common
• Hysteresis
mode transient immunity of 10 kV/µs at a common
mode voltage of 1000 volts. • Totem pole output (no pullup resistor required)
• Available in 8-Pin DIP, SOIC-8, widebody packages
Functional Diagram • Guaranteed performance from -40°C to 85°C
HCPL-2201/11 • Safety approval
HCPL-0201/11
HCNW2201/11 HCPL-2202/12 – UL recognized -3750 V rms for 1 minute (5000 V
NC 1 8 VCC NC 1 8 VCC rms for 1 minute for HCNW22XX) per UL1577
ANODE 2 7 VO ANODE 2 7 NC – CSAapproved
– IEC/EN/DIN EN 60747-5-2 approved with VIORM =
CATHODE 3 6 NC CATHODE 3 6 VO
630 V peak (HCPL-2211/2212 Option 060 only) and
NC 4 5 GND NC 4 5 GND VIORM = 1414 V peak (HCNW22XX only)
SHIELD SHIELD
• MIL-PRF-38534 hermetic version available
HCPL-2231/32
(HCPL-52XX/62XX)
ANODE 1 1 8 VCC
TRUTH TABLE
(POSITIVE LOGIC) Applications
CATHODE 1 2 7 VO1 LED VO
ON HIGH • Isolation of high speed logic systems
OFF LOW
CATHODE 2 3 6 VO2 • Computer-peripheral interfaces
ANODE 2 4 5 GND • Microprocessor system interfaces
SHIELD
• Ground loop elimination
A 0.1 µF bypass capacitor must be connected between pins 5 and 8. • Pulse transformer replacement
• High speed line receiver
• Power control systems

CAUTION: It is advised that normal static precautions be taken in handling and assembly
HCPL-2201 Functional Diagram
of this component to prevent damage and/or degradation which may be induced by ESD.
The electrical and switching characteristics of the HCPL- and CMOS logic and result in lower power consump­tion
22XX, HCPL-02XX and HCNW22XX are guaranteed from compared to other high speed couplers. Logic signals
-40°C to +85°C and a VCC from 4.5 volts to 20 volts. Low IF are transmitted with a typical propagation delay of
and wide VCC range allow compati­bil­ity with TTL, LSTTL, 150 ns.

Selection Guide
Small- Widebody
Minimum CMRInput      8-Pin DIP (300 Mil) Outline SO-8 (400 Mil) Hermetic
On- Single Dual Single Single Single and
dV/dt Current Channel Channel Channel Channel Dual Channel
(V/µs) VCM (V) (mA) Package Package Package Package Packages
1,000 50 1.6 HCPL-2200[1,2] HCPL-0201 HCNW2201
HCPL-2201
HCPL-2202
1.8 HCPL-2231
2,500 400 1.6 HCPL-2219[1,2]
5,000[3] 300[3] 1.6 HCPL-2211 HCPL-0211 HCNW2211
HCPL-2212
1.8 HCPL-2232
1,000 50 2.0 HCPL-52XX[2]
HCPL-62XX[2]

Notes:
1. HCPL-2200/2219 devices include output enable/disable function.
2. Technical data for the HCPL-2200/2219, HCPL-52XX and HCPL-62XX are on separate Avago publications.
3. Minimum CMR of 10 kV/µs with VCM = 1000 V can be achieved with input current, IF, of 5 mA.

Schematic
ICC
VCC
8

IO1
1 IF1
+ VO1
VF1 7
ICC
VCC –
8 2

IO SHIELD
2 IF
+ VO
VF
–
3
IO2
GND 3
SHIELD – VO2
5 6
VF2
HCPL-2201/02/11/12 +
HCPL-0201/11 4 IF2
HCNW2201/11
GND
SHIELD 5
HCPL-2231/32

HCPL-2201 Schematic


Ordering Information
HCPL-2201, HCPL-2202, HCPL-2211, HCPL-2212, HCPL-2231, HCPL-2232, HCPL-0201, HCPL-0211 are UL Recognized
with 3750 Vrms for 1 minute per UL1577.
HCNW2201 and HCNW2211 are UL Recognized with 5000 Vrms for 1 minute per UL1577.
All devices listed above are approved under CSA Component Acceptance Notice #5, File CA 88324.
Option UL 5000
Vrms/ 1
Part RoHS Non RoHS Surface Gull Tape & Minute IEC/EN/DIN EN
number Compliant Compliant Package Mount Wing Reel rating 60747-5-2 Quantity
-000E No option 50 per tube
-300E -300 X X 50 per tube
HCPL-2201
HCPL-2202 -500E -500 300mil X X X 1000 per reel
HCPL-2211 -060E -060 DIP-8 X 50 per tube
HCPL-2212
-360E -360 X X X 50 per tube
-560E -560 X X X X 1000 per reel
-000E No option 50 per tube
HCPL-2231
-300E -300 X X 50 per tube
HCPL-2232
-500E -500 X X X 1000 per reel
-000E No option 100 per tube
HCPL-0201 -500E -500 X X X 1500 per reel
SO-8
HCPL-0211 -060E -060 X 100 per tube
-560E -560 X X X X 1500 per reel
-000E No option 400mil 42 per tube
HCNW2201
-300E -300 Widebody X X 42 per tube
HCNW2211
-500E -500 DIP-8 X X X 750 per reel

To order, choose a part number from the part number column and combine with the desired option from the option
column to form an order entry.
Example 1:
HCPL-2202-560E to order product of 300mil DIP Gull Wing Surface Mount package in Tape and Reel packaging
with IEC/EN/DIN EN 60747-5-2 Safety Approval in RoHS compliant.
Example 2:
HCPL-2202 to order product of 300mil DIP package in tube packaging and non RoHS compliant.
Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation ‘#XXX’ is used for existing products, while (new) products launched since 15th July 2001 and
RoHS compliant option will use ‘-XXXE‘.


Package Outline Drawings
8-Pin DIP Package (HCPL-2201/02/11/12/31/32)

9.65 ± 0.25 7.62 ± 0.25

(0.380 ± 0.010) (0.300 ± 0.010)

TYPE NUMBER 8 7 6 5 6.35 ± 0.25

OPTION CODE* (0.250 ± 0.010)
A XXXXZ DATE CODE

YYWW RU
UL
1 2 3 4 RECOGNITION

1.78 (0.070) MAX.

1.19 (0.047) MAX.

+ 0.076
5° TYP. 0.254 - 0.051

3.56 ± 0.13 + 0.003)

4.70 (0.185) MAX. (0.010 - 0.002)
(0.140 ± 0.005)

0.51 (0.020) MIN.

2.92 (0.115) MIN.

1.080 ± 0.320 0.65 (0.025) MAX. DIMENSIONS IN MILLIMETERS AND (INCHES).

(0.043 ± 0.013) * MARKING CODE LETTER FOR OPTION NUMBERS
2.54 ± 0.25 "V" = OPTION 060
(0.100 ± 0.010) OPTION NUMBERS 300 AND 500 NOT MARKED.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (HCPL-2201/02/11/12/31/32)

LAND PATTERN RECOMMENDATION

9.65 ± 0.25
1.016 (0.040)
(0.380 ± 0.010)

8 7 6 5

6.350 ± 0.25
(0.250 ± 0.010) 10.9 (0.430)

1 2 3 4

2.0 (0.080)
1.27 (0.050)

1.780 9.65 ± 0.25

(0.070) (0.380 ± 0.010)
1.19 MAX.
(0.047) 7.62 ± 0.25
MAX. (0.300 ± 0.010)
+ 0.076
0.254 - 0.051
3.56 ± 0.13 + 0.003)
(0.140 ± 0.005) (0.010 - 0.002)

1.080 ± 0.320
(0.043 ± 0.013) 0.635 ± 0.25
(0.025 ± 0.010)
12° NOM.
2.54 0.635 ± 0.130
(0.100) (0.025 ± 0.005)
BSC
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.


Small-Outline SO-8 Package (HCPL-0201/11)
LAND PATTERN RECOMMENDATION

8 7 6 5
5.994 ± 0.203
(0.236 ± 0.008)
XXX
3.937 ± 0.127 YWW TYPE NUMBER 7.49 (0.295)
(0.155 ± 0.005) (LAST 3 DIGITS)
DATE CODE

PIN ONE 1 2 3 4 1.9 (0.075)

0.406 ± 0.076
(0.016 ± 0.003) 1.270 BSC
0.64 (0.025)
(0.050)

* 5.080 ± 0.127 7o 0.432

45o X
(0.200 ± 0.005) (0.017)

3.175 ± 0.127
(0.125 ± 0.005) 0 ~ 7o 0.228 ± 0.025
1.524
(0.009 ± 0.001)
(0.060)

0.203 ± 0.102
(0.008 ± 0.004)
* TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 0.305 MIN.
5.207 ± 0.254 (0.205 ± 0.010) (0.012)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.

8-Pin Widebody DIP Package (HCNW2201/11)

11.15 ± 0.15 11.00 MAX.

(0.442 ± 0.006) (0.433)

9.00 ± 0.15
8 7 6 5 (0.354 ± 0.006)
TYPE NUMBER
A DATE CODE
HCNWXXXX

YYWW

1 2 3 4

10.16 (0.400)
TYP.
1.55
(0.061) 7o TYP.
MAX. + 0.076
0.254 - 0.0051
+ 0.003)
(0.010 - 0.002)
5.10 MAX.
(0.201)

3.10 (0.122)
3.90 (0.154) 0.51 (0.021) MIN.

2.54 (0.100)
TYP.
1.78 ± 0.15 0.40 (0.016)
(0.070 ± 0.006) 0.56 (0.022) DIMENSIONS IN MILLIMETERS (INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.


8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW2201/11)

11.15 ± 0.15
(0.442 ± 0.006) LAND PATTERN RECOMMENDATION

8 7 6 5

9.00 ± 0.15
(0.354 ± 0.006) 13.56
(0.534)

1 2 3 4

1.3 2.29
(0.051) (0.09)

1.55 12.30 ± 0.30

(0.061) (0.484 ± 0.012)
MAX.
11.00 MAX.
(0.433)

4.00 MAX.
(0.158)

1.78 ± 0.15
(0.070 ± 0.006) 1.00 ± 0.15
0.75 ± 0.25 (0.039 ± 0.006) + 0.076
2.54 0.254 - 0.0051
(0.030 ± 0.010)
(0.100)
BSC + 0.003)
(0.010 - 0.002)
DIMENSIONS IN MILLIMETERS (INCHES).
7o NOM.
LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

Solder Reflow Temperature Profile

300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. PEAK
PEAK
TEMP.
TEMP.
245°C
240°C
PEAK
TEMP.
230°C
TEMPERATURE (°C)

200
2.5°C ± 0.5°C/SEC.
SOLDERING
30 TIME
160°C
150°C SEC. 200°C
140°C
30
3°C + 1°C/–0.5°C SEC.

100
PREHEATING TIME
150°C, 90 + 30 SEC. 50 SEC.

TIGHT
ROOM TYPICAL
TEMPERATURE LOOSE

0
0 50 100 150 200 250

TIME (SECONDS)

Note: Non-halide flux should be used.


Recommended Pb-Free IR Profile
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
tp
20-40 SEC.
260 +0/-5 °C
Tp
217 °C
TL
RAMP-UP
TEMPERATURE

3 °C/SEC. MAX. RAMP-DOWN

150 - 200 °C 6 °C/SEC. MAX.
Tsmax
Tsmin
ts tL
PREHEAT 60 to 150 SEC.
60 to 180 SEC.

25
t 25 °C to PEAK
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
Tsmax = 200 °C, Tsmin = 150 °C

Note: Non-halide flux should be used.

Regulatory Information
The HCPL-22XX/02XX and HCNW22XX have been approved by the following organizations:

UL IEC/EN/DIN EN 60747-5-2
Recognized under UL 1577, Component Recognition Approved under:
Program, File E55361. IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
CSA DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01
Approved under CSA Component Acceptance Notice (Option 060 and HCNW only)
#5, File CA 88324.

Insulation and Safety Related Specifications

8-pin DIP Package
8-Pin DIP Widebody
(300 Mil) SO-8 (400 Mil)
Parameter Symbol Value Value Value Units Conditions
Minimum External L(101) 7.1 4.9 9.6 mm Measured from input terminals
Air Gap (External to output terminals, shortest
Clearance) distance through air.
Minimum External L(102) 7.4 4.8 10.0 mm Measured from input terminals
Tracking (External to output terminals, shortest
Creepage) distance path along body.
Minimum Internal 0.08 0.08 1.0 mm Through insulation distance,
Plastic Gap conductor to conductor, usually
(Internal Clearance) the direct distance between the
photoemitter and photodetector
inside the optocoupler cavity.
Minimum Internal NA NA 4.0 mm Measured from input terminals
Tracking (Internal to output terminals, along
Creepage) internal cavity.
Tracking Resistance CTI 200 200 200 Volts DIN IEC 112/VDE 0303 Part 1
(Comparative
Tracking Index)
Isolation Group IIIa IIIa IIIa Material Group
(DIN VDE 0110, 1/89, Table 1)
Option 300 - surface mount classification is Class A in accordance with CECC 00802.


IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
(HCPL-2211/2212 Option 060 ONLY)
Description Symbol Characteristic Units
Installation classification per DIN VDE 0110/1.89, Table 1
  for rated mains voltage ≤300 V rms I-IV
  for rated mains voltage ≤450 V rms I-III
Climatic Classification 55/85/21
Pollution Degree (DIN VDE 0110/1.89) 2
Maximum Working Insulation Voltage VIORM 630 V peak
Input to Output Test Voltage, Method b*
  VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 1181 V peak
  Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
  VIORM x 1.5 = VPR, Type and sample test, VPR 945 V peak
  tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec) VIOTM 6000 V peak
Safety Limiting Values
  (Maximum values allowed in the event of a failure,
  also see Figure 12, Thermal Derating curve.)
   Case Temperature TS 175 °C
   Input Current IS,OUTPUT 230 mA
   Output Power PS,OUTPUT 600 mW
Insulation Resistance at TS, VIO = 500 V RS ≥109 Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN
60747-5-2, for a detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica-
tion.


IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics
(HCNW22XX ONLY)
Description Symbol Characteristic Units
Installation classification per DIN VDE 0110/1.89, Table 1
  for rated mains voltage ≤600 V rms I-IV
  for rated mains voltage ≤1000 V rms I-III
Climatic Classification 55/100/21
Pollution Degree (DIN VDE 0110/1.89) 2
Maximum Working Insulation Voltage VIORM 1414 V peak
Input to Output Test Voltage, Method b*
  VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec, VPR 2652 V peak
  Partial Discharge < 5 pC
Input to Output Test Voltage, Method a*
  VIORM x 1.5 = VPR, Type and sample test, VPR 2121 V peak
  tm = 60 sec, Partial Discharge < 5 pC
Highest Allowable Overvoltage*
(Transient Overvoltage, tini = 10 sec) VIOTM 8000 V peak
Safety Limiting Values
  (Maximum values allowed in the event of a failure,
  also see Figure 12, Thermal Derating curve.)
   Case Temperature TS 150 °C
   Current (Input Current IF, PS = 0) IS,INPUT 400 mA
   Output Power PS,OUTPUT 700 mW
Insulation Resistance at TS, VIO = 500 V RS ≥109 Ω

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN 60747-5-2, for a
detailed description.
Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in applica-
tion.


Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Note
Storage Temperature TS -55 125 °C
Operating Temperature TA -40 85 °C
Average Forward Input Current IF(AVG) 10 mA 1
Peak Transient Input Current
  (≤ 1 µs Pulse Width, 300 pps) IF(TRAN) 1.0 A 1
  (≤ 200 µs Pulse Width, HCNW22XX 40 mA
   < 1% Duty Cycle)
Reverse Input Voltage VR 5 V 1
HCNW22XX 3
Average Output Current IO 25 mA 1
Supply Voltage VCC 0 20 V
Output Voltage VO -0.5 20 V 1
Total Package Power Dissipation PT 210 mW 2
HCPL-223X 294
Output Power Dissipation PO See Figure 7 1
Lead Solder Temperature (Through Hole Parts Only)            260°C for 10 sec.,
   1.6 mm below seating plane
HCNW22XX     260°C for 10 sec., up to seating plane
Solder Reflow Temperature Profile       See Package Outline Drawings section
(Surface Mount Parts Only)

Recommended Operating Conditions

Parameter Symbol Min. Max. Units
Power Supply Voltage VCC 4.5 20 V
Forward Input Current (ON) IF(ON) 1.6* 5 mA
HCPL-223X 1.8†
Forward Input Voltage (OFF) VF(OFF) - 0.8 V
Operating Temperature TA -40 85 °C
Junction Temperature TJ -40 125 °C
Fan Out N 4 TTL Loads

*The initial switching threshold is 1.6 mA or less. It is recommended that 2.2 mA be used to permit at least a 20% LED degradation guardband.
†The initial switching threshold is 1.8 mA or less. It is recommended that 2.5 mA be used to permit at least a 20% LED degradation guardband.

10
Electrical Specifications
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V, unless otherwise specified.
All Typicals at TA = 25°C. See Note 7.
Parameter Sym. Min. Typ. Max. Units    Test ConditionsFig. Note
Logic Low Output Voltage VOL 0.5 V IOL = 6.4 mA (4 TTL Loads) 1, 3 1
Logic High Output Voltage VOH 2.4 ** V IOH = -2.6 mA 2, 3, 1
(V

OUT
> VCC
) 2.7 IOH = -0.4 mA
Output Leakage Current IOHH 100 µA VO = 5.5 V IF = 5 mA 1
500 VO = 20 V
Logic Low Supply ICCL 3.7 6.0 mA VCC = 5.5 V VF = 0 V
Current
4.3 7.0 VCC = 20 V IO = Open
HCPL-223X 7.4 12.0 VCC = 5.5 V
8.6 14.0 VCC = 20 V
Logic High Supply ICCH 2.4 4.0 mA VCC = 5.5 V IF = 5 mA
Current
2.7 5.0 VCC = 20 V IO = Open
HCPL-223X 4.8 8.0 VCC = 5.5 V
5.4 10.0 VCC = 20 V
Logic Low Short Circuit IOSL 15 mA VO = VCC = 5.5 V VF = 0 V 1, 3
Output Current
20 VO = VCC = 20 V VO = GND
Logic High Short Circuit IOSH -10 mA VCC = 5.5 V IF = 5 mA 1, 3
Output
Current -20 VCC = 20 V
Input Forward Voltage VF 1.5 1.7 V TA = 25°C IF = 5 mA 4 1
1.85
HCNW22XX 1.5 1.82 TA = 25°C
1.95
Input Reverse Breakdown BVR 5 V IR = 10 µA 1
Voltage
HCNW22XX 3 IR = 100 µA
Input Diode Temperature ∆VF -1.7 mV/°C IF = 5 mA
Coefficient
HCNW22XX ∆TA -1.4
Input Capacitance CIN 60 pF f = 1 MHz, VF = 0 V 1, 4
HCNW22XX 70

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

**Typical VOH = VCC - 2.1 V.

11
Switching Specifications (AC)
-40°C ≤ TA ≤ 85°C, 4.5 V ≤ VCC ≤ 20 V, 1.6 mA ≤ IF(ON)* ≤ 5 mA, 0 V ≤ VF(OFF) ≤ 0.8 V.
All Typicals at TA = 25°C, VCC = 5 V, IF(ON) = 3 mA unless otherwise specified.
Parameter Sym. Min. Typ. Max. Units     Test Conditions Fig. Note
Propagation Delay Time tPHL 150 ns Without Peaking Capacitor 5, 6 1, 6
to Logic Low
160 HCNW22XX
Output Level
150 300 With Peaking Capacitor
Propagation Delay Time tPLH 110 ns Without Peaking Capacitor 5, 6 1, 6
to Logic High
180 HCNW22XX
Output Level
90 300 With Peaking Capacitor
Output Rise Time (10-90%) tr 30 ns 5, 9 1
Output Fall Time (90-10%) tf 7 ns 5, 9 1

Parameter Sym.    Device Min. Units    Test Conditions Fig. Note

Logic High |CMH| HCPL-2201/02 1,000 V/µs |VCM| = 50 V VCC = 5 V 10 1, 7
Common Mode HCPL-0201 IF = 1.6 mA† TA = 25°C
Transient HCPL-2231
Immunity HCNW2201
HCPL-2211/12 5,000 V/µs |VCM| = 300 V
HCPL-0211 IF = 1.6 mA‡
HCPL-2232 10,000 V/µs |VCM| = 1 kV
HCNW2211 IF = 5.0 mA
Logic Low |CML| HCPL-2201/02 1,000 V/µs |VCM| = 50 V VF = 0 V 10 1, 7
Common Mode HCPL-0201 VCC = 5 V
Transient HCPL-2231 TA = 25°C
Immunity HCNW2201
HCPL-2211/12 10,000 V/µs |VCM| = 1 kV
HCPL-0211
HCPL-2232
HCNW2211

*For HCPL-223X, 1.8 mA ≤ IF(ON) ≤ 5 mA.

†IF = 1.8 mA for HCPL-2231.
‡IF = 1.8 mA for HCPL-2232.

12
Package Characteristics
Parameter Sym. Min. Typ. Max. Units     Test Conditions Fig. Note
Input-Output Momentary VISO 3750 V rms RH < 50%, t = 1 min. 5, 10
Withstand HCNW22XX 5000 TA = 25°C 5, 11
Voltage*
Input-Output Resistance RI-O 1012 Ω VI-O = 500 Vdc 5
HCNW22XX 1012 1013 TA = 25°C
1011 TA = 100°C
Input-Output Capacitance CI-O 0.6 pF f = 1 MHz, 5
HCNW22XX 0.5 0.6 TA = 25°C, VI-O = 0 Vdc
Input-Input Insulation II-I 0.005 µA Relative Humidity = 45%, 12
Leakage Current t = 5 s, VI-I = 500 V
Resistance (Input-Input) RI-I 1011 Ω VI-I = 500 V 12
Capacitance (Input-Input) CI-I 0.25 pF f = 1 MHz 12

*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number
5963-2203

Notes:
1. Each channel.
2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
3. Duration of output short circuit time should not exceed 10 ms.
4. For single devices, input capacitance is measured between pin 2 and pin 3.
5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of
the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the
trailing edge of the output pulse.
7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.
CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.
8. For HCPL-2202/12, VO is on pin 6.
9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table.
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.

13
 IOH – HIGH LEVEL OUTPUT CURRENT – mA
VOL – LOW LEVEL OUTPUT VOLTAGE – V
1.0 0 5
VCC = 4.5 V VCC = 4.5 V VCC = 4.5 V
0.9 -1
VF = 0 V IF = 5 mA TA = 25 °C

VO – OUTPUT VOLTAGE – V
0.8 IO = 6.4 mA 4
-2
0.7 VO = 2.7 V
0.6 -3 3
0.5 -4 IO = -2.6 mA
0.4 2
-5
0.3 VO = 2.4 V
-6
0.2 1
-7 IO = 6.4 mA
0.1
0 -8 0
-60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 0 0.5 1.0 1.5
TA – TEMPERATURE – °C TA – TEMPERATURE – °C IF – INPUT CURRENT – mA

Figure 1. Typical logic low output voltage vs. tem- Figure 2. Typical logic high output current vs. tem- Figure 3. Typical output voltage vs. forward input
perature. perature. current.
HCPL-2201 fig 1 HCPL-2201 fig 2 HCPL-2201 fig 3
HCPL-22XX
HCPL-02XX HCNW22XX
1000 1000
TA = 25 °C TA = 25 °C
IF – FORWARD CURRENT – mA

IF – FORWARD CURRENT – mA

100 100
IF IF
+ +
10 VF 10 VF
– –
1.0 1.0

0.1 0.1

0.01 0.01

0.001 0.001
1.1 1.2 1.3 1.4 1.5 1.1 1.2 1.3 1.4 1.5 1.6
VF – FORWARD VOLTAGE – V VF – FORWARD VOLTAGE – V

Figure 4. Typical input diode forward characteristic.

HCPL-2201 fig 4a HCPL-2201 fig 4b

PULSE GEN. VCC PULSE GEN.

tr = tf = 5 ns tr = tf = 5 ns
f = 100 kHz OUTPUT VO f = 100 kHz
HCPL-2201/11 VCC
10 % DUTY HCPL-02XX MONITORING 10 % DUTY
CYCLE HCNW22XX NODE 5V CYCLE
VO = 5 V VO = 5 V OUTPUT VO
ZO = 50 VCC 8 ZO = 50 MONITORING
1
619 Ω HCPL-223X NODE 5V
* D1
2 7 1 VCC 8
INPUT INPUT * D1 619 Ω
MONITORING D2 MONITORING
6 C2 = NODE
NODE 3 2 7
15 pF
D3 D2
R1 4 GND 5 5 kΩ 3 6 C2 =
C1 = 15 pF
120 pF D4 D3
R1 4 GND 5 5 kΩ
C1 =
120 pF D4
THE PROBE AND JIG CAPACITANCES
ARE INCLUDED IN C1 AND C2.
THE PROBE AND JIG CAPACITANCES
R1 2.15 kΩ 1.10 kΩ 681 Ω ARE INCLUDED IN C1 AND C2.
IF (ON) 1.6 mA 3 mA 5 mA
ALL DIODES ARE 1N916 OR 1N3064. R1 1.96 kΩ 1.10 kΩ 681 Ω
IF (ON) 1.8 mA 3 mA 5 mA
IF (ON) ALL DIODES ARE 1N916 OR 1N3064.
INPUT IF 50 % IF (ON)
0 mA

tPLH tPHL
VOH
HCPL-2201 fig 5a 1.3 V
OUTPUT VO VOL
HCPL-2201 fig 5b
Figure 5. Circuit for tPLH, tPHL, tr, tf. * 0.1 µF BYPASS — SEE NOTE 9.

14

HCPL-2201 fig 5c
 HCPL-22XX
HCPL-02XX HCNW22XX
250 250 80
VCC = 5.0 V, 20 V VCC = 5.0 V, 20 V
C1 (120 pF) PEAKING CAPACITOR

PO – MAXIMUM OUTPUT POWER

C1 (120 pF) PEAKING

tP – PROPAGATION DELAY – ns
tP – PROPAGATION DELAY – ns

CAPACITOR IS USED. IF (mA) IS USED. SEE FIGURE 5.

SEE FIGURE 5. 5 TA = 75 °C
200 200 IF (mA) 60

PER CHANNEL (mW)

*IF = 1.8 mA FOR HCPL-223X 3 5 TA =
DEVICES. 80°C
1.6*
3
150 150 40
tPHL 1.6* tPHL 1.6
-5
TA = 85 °C
1.6,
100 5
100 20
tPLH
tPLH
50 50 0
-60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100 0 5 10 15 20
TA – TEMPERATURE – °C TA – TEMPERATURE – °C VCC – SUPPLY VOLTAGE – V

Figure 6. Typical propagation delays vs. temperature. Figure 7. Maximum output power per channel vs. sup-
ply voltage.
HCPL-2201 fig 6a HCPL-2201 fig 6b HCPL-2201 fig 7
VOH – HIGH LEVEL OUTPUT VOLTAGE – V

20 100
TYPICAL VCC = 5 V
VOH vs. VCC
tr, tf – RISE, FALL TIME – ns

AT IO = -2.6 mA 80
15 TA = 25 °C

60
10
40
tr

5
20
tf
0 0
0 5 10 15 20 -60 -40 -20 0 20 40 60 80 100
VCC – SUPPLY VOLTAGE – V TA – TEMPERATURE – °C

Figure 8. Typical logic high output voltage vs. supply Figure 9. Typical rise, fall time vs. temperature.
voltage.
HCPL-2201 fig 8 HCPL-2201 fig 9

HCPL-2201/11
HCPL-02XX VCC R1 VCC
HCNW22XX HCPL-2231/32
A
1 8 OUTPUT VO 1 8 OUTPUT VO
A MONITORING MONITORING
NODE B NODE
B 2 7 2 7
+
RIN VFF
3 6 0.1 µF 3 6 0.1 µF
–
BYPASS BYPASS
+
VFF 4 5 4 5
–
VCM VCM
PULSE GENERATOR + – PULSE GENERATOR + –

VCM (PEAK)
|VCM| VCM (PEAK)
|VCM|
0V
0 V SWITCH AT A: IF = 1.6 mA**
VOH SWITCH AT A: IF = 1.6 mA**
VOH
VO (MIN.)*
V (MIN.)*
OUTPUT VO SWITCH AT B: VOF = 0 V
OUTPUT VO SWITCH AT B: VF = 0 V
VO (MAX.)*
VO (MAX.)*
VOL
VOL
HCPL-2201 fig 10b
* SEE NOTE 7, 9.
* SEE NOTE 7, 9.
** IF = 1.8 mA FOR HCPL-2231/32 DEVICES.
** IF = 1.8 mA FOR HCPL-2231/32 DEVICES.
HCPL-2201 fig 10a
Figure 10. Test circuit for common mode transient immunity and typical waveforms.

15

HCPL-2201 fig 10c

HCPL-2201 fig 10c
 HCPL-22XX
HCPL-02XX HCNW22XX
1.0 1.0

INPUT CURRENT THRESHOLD – mA

INPUT CURRENT THRESHOLD – mA

VCC = 5.0 V VCC = 5.0 V

VCC = 20 V VCC = 20 V
0.9 0.9

0.8 0.8

IF (ON) IF (ON)
0.7 IF (OFF) 0.7
IF (OFF)

0.6 0.6 IF (ON)

IF (ON) IF (OFF)
IF (OFF)
0.5 0.5
-60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100
TA – TEMPERATURE – °C TA – TEMPERATURE – °C

Figure 11. Typical input threshold current vs. temperature.

HCPL-2201 fig 11a HCPL-2201 fig 11b

HCPL-2211/2212 OPTION 060 HCNW22XX

OUTPUT POWER – PS, INPUT CURRENT – IS

1000
OUTPUT POWER PS, INPUT CURRENT IS

800
PS (mW) PS (mW)
900
700 IS (mA) IS (mA)
800
600
700
500 600
400 500
400
300
300
200
200
100 100
0 0
0 25 50 75 100 125 150 175 200 0 25 50 75 100 125 150 175
TS – CASE TEMPERATURE – °C TS – CASE TEMPERATURE – °C

Figure 12. Thermal derating curve, dependence of safety limiting value with case temperature per IEC/EN/DIN EN 60747-5-2.
HCPL-2201 fig 12b
HCPL-2201 fig 12a

HCPL-2201/11
HCPL-02XX
HCNW22XX
VCC2 (+5 V)
VCC1 (+5 V) 1 8
1.1 kΩ
2 7 DATA OUTPUT

DATA INPUT 3 6 *
TTL OR LSTTL
UP TO 16 LSTTL LOADS
4 5 OR 4 TTL LOADS

1
* 0.1 µF BYPASS

Figure 13a. Recommended LSTTL to LSTTL circuit where 500 ns propagation delay is sufficient.

HCPL-2201 fig 13a

 HCPL-2201/11
HCPL-02XX
HCNW22XX
VCC2 (+5 V)
80 Ω
VCC1 (+5 V) 1 8
1.1 kΩ 120 pF
2 7 DATA OUTPUT

DATA INPUT 3 6 *
TTL OR LSTTL
UP TO 16 LSTTL LOADS
4 5 OR 4 TTL LOADS

1 * 0.1 µF BYPASS

Figure 13b. Recommended LSTTL to LSTTL circuit for applications requiring a maximum allowable propagation delay of 300 ns.

HCPL-2201 fig 13b

VCC2
HCPL-2201/11 (4.5 TO 20 V)
HCPL-02XX
HCNW22XX
80 Ω*
VCC1 (+5 V) 1 VCC 8 RL
1.1 kΩ 120 pF* HCPL-2201/11
2 7 CMOS DATA OUTPUT HCPL-02XX
VCC1 (+5 V) HCNW22XX
** 1.1 kΩ
DATA INPUT 3 6
1 VCC 8
TTL OR LSTTL
GND
4 5 DATA
2 7
INPUT
D1
TOTEM TTL or 3 6
POLE 2 LSTTL
1 VCC2 RL * 120 pF PEAKING CAPACITOR GND
OUTPUT 4 5
GATE 5V 1.1 kΩ MAY BE OMITTED AND 80 Ω
10 V 2.37 kΩ RESISTOR MAY BE SHORTED
15 V 3.83 kΩ WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.
20 V 5.11 kΩ D1 (1N4150) REQUIRED FOR
**0.1 µF BYPASS ACTIVE PULL-UP DRIVER.

Figure 14. LSTTL to CMOS interface circuit. Figure 15. Alternative LED drive circuit.

HCPL-2201 fig 14

HCPL-2201/11
HCPL-02XX
HCNW22XX
80 Ω* HCPL-2201 fig 15
VCC (+5 V) 1 VCC 8
1.1 kΩ 120 pF*
2 7
4.7 kΩ
DATA INPUT 3 6
TTL OR LSTTL
GND
4 5

OPEN
COLLECTOR * 120 pF PEAKING CAPACITOR
GATE MAY BE OMITTED AND 80 Ω
RESISTOR MAY BE SHORTED
WHERE 500 ns PROPAGATION
DELAY IS SUFFICIENT.

Figure 16. Series LED drive with open collector gate (4.7 k resistor shunts IOH from the LED).

17
For product information and a complete list of distributors, please go to our website: www.avagotech.com

Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries.
Data subject to change. Copyright © 2007 Avago Technologies Limited. All rights reserved. Obsoletes AV01-0556EN
AV02-0674EN - September 4, 2007