0% found this document useful (0 votes)
17 views13 pages

SM 94

The document provides torque specifications for various exterior trim components, detailing the necessary torque values for rear spoiler bolts and nuts. It includes step-by-step removal and installation procedures for rear quarter panel moulding, rear spoilers, and hood badges, emphasizing care to avoid damage and proper alignment during installation. Additionally, it highlights the importance of discarding old clips and ensuring cleanliness before installing new components.

Uploaded by

jonas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
17 views13 pages

SM 94

The document provides torque specifications for various exterior trim components, detailing the necessary torque values for rear spoiler bolts and nuts. It includes step-by-step removal and installation procedures for rear quarter panel moulding, rear spoilers, and hood badges, emphasizing care to avoid damage and proper alignment during installation. Additionally, it highlights the importance of discarding old clips and ensuring cleanliness before installing new components.

Uploaded by

jonas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 13

Published: 03-Jul-2011

Exterior Trim and Ornamentation -


Torque Specifications
Item Nm lb-ft lb-in
Rear spoiler ground cable retaining bolt 10 - 89
Rear spoiler retaining nuts 7 - 62

cardiagn.com
Published: 09-Jun-2011
Exterior Trim and Ornamentation - Rear Quarter Panel Moulding
Removal and Installation

Removal

NOTE: Removal steps in this procedure may contain installation details.

1.

cardiagn.com
2. NOTE: Discard the retaining clips.

Make sure that the centre part of the clip is fully


removed from the outer part of the clip. It is not
possible to prevent the centre part of the clip
falling into the body of the vehicle.
3. CAUTION: Take extra care not to damage the
component.

cardiagn.com
4. NOTE: Discard the sealing plug.

Installation

1. To install, reverse the removal procedure.


Published: 09-Jun-2011
Exterior Trim and Ornamentation - Rear Spoiler
Removal and Installation

Removal

All vehicles

1. NOTE: The procedure must be carried out on both sides.

Refer to: A-Pillar Trim Panel (501-05 Interior Trim and


Ornamentation, Removal and Installation).

3-door

NOTE: The procedure must be carried out on both sides.

2. Refer to: B-Pillar Upper Trim Panel - 3-Door (501-05 Interior Trim and
Ornamentation, Removal and Installation).

5-door

cardiagn.com
3. NOTE: The procedure must be carried out on both sides.

Refer to: B-Pillar Upper Trim Panel - 5-Door (501-05 Interior Trim and
Ornamentation, Removal and Installation).

All vehicles

4. NOTE: The procedure must be carried out on both sides.

Refer to: C-Pillar Upper Trim Panel (501-05 Interior Trim and
Ornamentation, Removal and Installation).

5. NOTE: The procedure must be carried out on both sides.

Refer to: D-Pillar Trim Panel (501-05 Interior Trim and


Ornamentation, Removal and Installation).

6. Refer to: Overhead Console (501-12 Instrument Panel and Console,


Removal and Installation).
7. NOTE: The step must be carried out on both
sides.

8. NOTE: The step must be carried out on both

cardiagn.com
sides.

9. NOTE: The step must be carried out on both


sides.
10. NOTE: The step must be carried out on both
sides.

11.

cardiagn.com
12.
13. NOTE: The procedure must be carried out on both
sides.

14. NOTE: The step must be carried out on both


sides.

cardiagn.com
15. NOTE: The step must be carried out on both
sides.
16.

17. NOTE: This step requires the aid of another

cardiagn.com
technician.

Lower the headliner for access.

18.
cardiagn.com
19. NOTE: The step must be carried out on both
sides.

Torque: 10 Nm

20. CAUTION: Take extra care not to damage the wiring harnesses.
cardiagn.com
Installation

1. NOTE: Do not tighten the rear spoiler retaining nuts at this


stage.

To install, reverse the removal procedure.

2. NOTE: Make sure that the gap is even between the rear spoiler
and the rear quarter panel moulding and the rear spoiler is flush
with the roof panel (use a suitable plastic straight edge).
3. NOTES:

Rear spoiler shown removed for clarity.

Loosen the rear spoiler retaining nuts.

cardiagn.com
4. NOTE: Rear spoiler shown removed for clarity.

Adjust the rear spoiler by rotating the adjustment studs clockwise


and counter clockwise as necessary.

5. NOTE: Rear spoiler shown removed for clarity.

Torque: 7 Nm
6. NOTE: Make sure that the gap is even between the rear spoiler

cardiagn.com
and the rear quarter panel moulding and the rear spoiler is flush
with the roof panel (use a suitable plastic straight edge).

If the rear spoiler is not correctly adjusted, follow Steps 3 to 6 of


the installation procedure until correct alignment is achieved.
Published: 21-Mar-2012
Exterior Trim and Ornamentation - Hood Badge
Removal and Installation

Removal

1. CAUTION: Remove any excessive adhesive from the hood.

Using a suitable tool or plastic spatula, remove the hood badge(s).

Installation

1. Clean the area prior to installation of the hood badge.

2. CAUTION: Using the centre of the grill as a starting point,


install the hood badge to the dimensions shown.

A - 25 mm / 0.9 inch
B - 40 mm / 1.6 inch
C - 50 mm / 1.9 inch

cardiagn.com

You might also like