Click on Subject/Paper under Semester to

enter. Environmental
Professional English Sciences
Professional and Sustainability -
English - I - - II - HS3252 Discrete GE3451
HS3152
Mathematics
Statistics and Theory of Computation
- MA3354
Numerical - CS3452
Matrices and
Methods - MA3251
Calculus Digital Principles
and Computer Artificial
- MA3151

Semester
Engineering Intelligence and
Semester

Organization
Semester

Graphics Machine Learning

Semester

- CS3351
Engineering - CS3491
Physics - PH3151 - GE3251
Foundation of Data
Physics for Science - CS3352 Database Management

4th
System - CS3492
2nd
1st

Engineering Information
3rd

Chemistry Science
Data Structure -
- CY3151 - PH3256 CS3301 Algorithms - CS3401
Basic Electrical and
Electronics Object Oriented Introduction to
Problem Solving Engineering Operating
Programming -
and Python - BE3251 Systems - CS3451
CS3391
Programming -
GE3151 Programming in C
- CS3251

Computer
Networks - Object Oriented
CS3591 Software
Engineering
- CCS356 Human Values and
Compiler Design - Ethics - GE3791
CS3501 Embedded
Semester

Semester

Systems and IoT - Open Elective 2

Cryptography CS3691
Semester
Semester

and Cyber
Security - Open Elective 3
CB3491 Open
Open Elective 4
5th

7th

Distributed Elective-1
8th

Computing
6th

Management
- CS3551 Elective-3
Elective
Elective 1 Elective-4

Elective 2 Elective-5

Elective-6
 Multi - Core
Architectures and
Programming
Probability and Queueing Physics for Transforms and
Theory Information Partial Differential
Science Equations
Technical English Engineering Engineering Chemistry
Physics
Engineering Graphics Total Quality Professional Ethics in
Management Engineering
Basic Electrical and Problem Solving Environmental Science
Electronics and and Python and Engineering
Measurement Engineering Programming
 www.BrainKart.
com
UNIT V DATA LINK AND PHYSICAL LAYERS
Data Link Layer – Framing – Flow control – Error control – Data-Link Layer Protocols –
HDLC –PPP - Media Access Control – Ethernet Basics – CSMA/CD – Virtual LAN –
Wireless LAN (802.11)- Physical Layer: Data and Signals - Performance – Transmission
media- Switching – Circuit

5.1 Data Link Layer

 In the OSI model, the data link layer is a 4 th layer from the top and 2nd layer from the
bottom.
 The communication channel that connects the adjacent nodes is known as links, and
in order to move the datagram from source to the destination, the datagram must be
moved across an individual link.
 Data link layer is responsible for converting data stream to signals bit by bit and to
send that over the underlying hardware. At the receiving end, Data link layer picks up
data from hardware which are in the form of electrical signals, assembles them in a
recognizable frame format, and hands over to upper layer.

Data link layer has two sub-layers:

 Logical Link Control: It deals with protocols, flow-control, and error control
 Media Access Control: It deals with actual control of media

Following services are provided by the Data Link Layer:

 Framing
 Addressing
 Error Control
 Flow Control

5.2 Framing
Framing is a point-to-point connection between two computers or devices consisting of a
wire in which data is transmitted as a stream of bits. However, these bits must be framed into
discernible blocks of information.
Framing is a function of the data link layer. It provides a way for a sender to transmit a set of
bits that are meaningful to the receiver. Frames have headers that contain information such as
error-checking codes.
At the data link layer, it extracts the message from the sender and provides it to the receiver
by providing the sender’s and receiver’s addresses.
The process of dividing the data into frames and reassembling it is transparent to the user and
is handled by the data link layer.
Framing is an important aspect of data link layer protocol design because it allows the
transmission of data to be organized and controlled.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

A frame has the following parts −

 Frame Header − It contains the source and the destination addresses of the frame.
 Payload field − It contains the message to be delivered.
 Trailer − It contains the error detection and error correction bits.
 Flag − It marks the beginning and end of the frame.

Types of framing

There are two types of framing:

1. Fixed-size: The frame is of fixed size and there is no need to provide boundaries to
the frame, the length of the frame itself acts as a delimiter.

Drawback: It suffers from internal fragmentation if the data size is less than the
frame size

Solution: Padding

2. Variable size: The size of the frame is variable during this form of framing. In variable-
size framing, we are in need of a way to outline the tip of the frame and also the starting of
the succeeding frame. This can be utilized in local area networks (LAN).

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
There are 2 different methods to define the frame boundaries, such as length field and finish
decimeters.

2.1 Length field–To confirm the length of the field, a length field is used. It is utilized in
Ethernet (1EEE 802.3).

2.2 End Delimeter–To confirm the size of the frame, a pattern is worn as a delimiter. This
methodology is worn in the token ring. In short, it is referred to as ED. Two different
methods are used to avoid this condition if the pattern happens within the message.

2.2.1 Bit-Oriented Framing

Most protocols use a special 8-bit pattern flag 01111110 as a result of the delimiter to
stipulate the beginning and so the end of the frame. Bit stuffing is completed at the
sender end and bit removal at the receiver end.

If we have a tendency to get a zero(0) after 5 1s. we have a tendency to tend to still stuff a
zero(0). The receiver will remove the zero. Bit stuffing is in addition said as bit
stuffing.

2.2.2 Byte-Oriented Framing

Byte stuffing is one of the methods of adding an additional byte once there is a flag or
escape character within the text. Take an illustration of byte stuffing as appeared in
the given diagram.

The sender sends the frame by adding three additional ESC bits and therefore the
destination machine receives the frame and it removes the extra bits to convert the
frame into an identical message.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

5.3 Flow Control

Flow control is a set of procedures that restrict the amount of data a sender should send
before it waits for some acknowledgment from the receiver.

 Flow Control is an essential function of the data link layer.

 It determines the amount of data that a sender can send.
 It makes the sender wait until an acknowledgment is received from the receiver’s end.
 Methods of Flow Control are Stop-and-wait, and Sliding window.

Stop-and-wait Protocol

Stop-and-wait protocol works under the assumption that the communication channel is
noiseless and transmissions are error-free.

Working :

 The sender sends data to the receiver.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 The sender stops and waits for the acknowledgment.
 The receiver receives the data and processes it.
 The receiver sends an acknowledgment for the above data to the sender.
 The sender sends data to the receiver after receiving the acknowledgment of
previously sent data.
 The process is unidirectional and continues until the sender sends the End of
Transmission (EoT) frame.

Sliding Window Protocol

The sliding window protocol is the flow control protocol for noisy channels that allows the
sender to send multiple frames even before acknowledgments are received. It is called a
Sliding window because the sender slides its window upon receiving the acknowledgments
for the sent frames.

Working:

 The sender and receiver have a “window” of frames. A window is a space that
consists of multiple bytes. The size of the window on the receiver side is always
1.
 Each frame is sequentially numbered from 0 to n - 1, where n is the window size
at the sender side.
 The sender sends as many frames as would fit in a window.
 After receiving the desired number of frames, the receiver sends an
acknowledgment. The acknowledgment (ACK) includes the number of the next
expected frame.

5.4 Error Control

Error control in data link layer is the process of detecting and correcting data frames that have
been corrupted or lost during transmission.

In case of lost or corrupted frames, the receiver does not receive the correct data-frame and
sender is ignorant about the loss. Data link layer follows a technique to detect transit errors
and

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
take necessary actions, which is retransmission of frames whenever error is detected or frame
is lost. The process is called Automatic Repeat Request (ARQ).

The error control mechanism in data link layer involves the following phases −

 Detection of Error − Transmission error, if any, is detected by either the sender or

the receiver.
 Acknowledgment − acknowledgment may be positive or negative.
o Positive ACK − On receiving a correct frame, the receiver sends a positive
acknowledge.
o Negative ACK − On receiving a damaged frame or a duplicate frame, the
receiver sends a negative acknowledgment back to the sender.
 Retransmission − The sender maintains a clock and sets a timeout period. If an
acknowledgment of a data-frame previously transmitted does not arrive before the
timeout, or a negative acknowledgment is received, the sender retransmits the frame.

Error control technique

There are three main techniques for error control –

Stop and Wait ARQ

This protocol involves the following transitions −

 A timeout counter is maintained by the sender, which is started when a frame is sent.
 If the sender receives acknowledgment of the sent frame within time, the sender is
confirmed about successful delivery of the frame. It then transmits the next frame
in queue.
 If the sender does not receive the acknowledgment within time, the sender assumes
that either the frame or its acknowledgment is lost in transit. It then retransmits the
frame.
 If the sender receives a negative acknowledgment, the sender retransmits the frame.

Go-Back-N ARQ

The working principle of this protocol is −

 The sender has buffers called sending window.

 The sender sends multiple frames based upon the sending-window size, without
receiving the acknowledgment of the previous ones.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 The receiver receives frames one by one. It keeps track of incoming frame’s
sequence number and sends the corresponding acknowledgment frames.
 After the sender has sent all the frames in window, it checks up to what sequence
number it has received positive acknowledgment.
 If the sender has received positive acknowledgment for all the frames, it sends next
set of frames.
 If sender receives NACK or has not receive any ACK for a particular frame, it
retransmits all the frames after which it does not receive any positive ACK

Selective Repeat ARQ

 Both the sender and the receiver have buffers called sending window and receiving
window respectively.
 The sender sends multiple frames based upon the sending-window size, without
receiving the acknowledgment of the previous ones.
 The receiver also receives multiple frames within the receiving window size.
 The receiver keeps track of incoming frame’s sequence numbers, buffers the frames
in memory.
 It sends ACK for all successfully received frames and sends NACK for only frames
which are missing or damaged.
 The sender in this case, sends only packet for which NACK is received.

5.5 Data Link Layer Protocols

Data link layer protocol is generally responsible to simply ensure and confirm that the bits
and bytes that are received are identical to bits and bytes being transferred. SDLC,
HDLC, SLIP, PPP, LCP, LAP, and NCP are some of the data link layer protocols.

SDLC:

SDLC stands for synchronous data link control protocol, is a communication protocol of a
computer.

It is usually used to carry system network architecture traffic. Synchronous data link protocol
connects all the remote devices to the mainframe computer at the Central location.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
This connection is done in two formats, point to point format i.e. one to one connection, and
point to multipoint format, i.e. one to many connections.

SDLC support one to many connections even in case of error detection or error recovery.

SDLC ensures that all the received data units are correct and flow is right from one network
point to the next network point.

HDLC:

HDLC stands for High-level data link control protocol, is a bit-orientated code transparent
synchronous protocol developed by ISO (International organization for standardization)
in1979.

It provides both connection-orientated and connectionless services. HDLC protocol contains

various wide-area protocols.

It is based on the SDLC protocol that supports both point-to-point and multipoint
communication.

HDLC frames are transferred over synchronous or asynchronous serial communication links.
HDLC uses various modes such as normal response mode, asynchronous response mode,
asynchronous balanced mode.

Normal response mode is used to share the secondary to primary link without contention.
asynchronous response mode is used for full-duplex links. asynchronous balanced mode,
support combined terminal which can act as both primary and secondary.

SLIP:

SLIP stands for Serial line interface protocol which is used to add framing byte at the end of
the IP Packet. SLIP is a data link layer protocol That transforms the IP packets among ISP
(Internet Service Providers) and home user over dial-up links.

SLIP is designed to work with ports and router connections. SLIP does not provide error
detection, being reliant on upper-layer protocols for this. Therefore, SLIP on its own is not
satisfactory over an error-prone dial-up connection.

PPP:

PPP stands for Point to point protocol. PPP is a data link layer protocol that provides the
same services as the Serial line interface protocol.

It is a robust protocol that transfers the other types of pockets also with the IP packets. It
provides two protocols LCP and NCP, that we will discuss in the next section. Point to point
protocol uses framing methods that describe the frames.

Point to point protocol is also called character orientated protocol which is used to detect
errors. PPC provides Connection authentication, data compression, encryption, and
transmission. It is

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
used over various networks such as phone lines, cellular telephones, serial cables, trunk lines,
ISDNs, Specialized radio links, etc.

LCP:

LCP stands for Link control protocol, is a part of point-to-point control protocol. LCP packets
determine the standards of data transmission.

LCP protocol is used to determine the identity of the linked devices, if the device is correct it
accepts it otherwise it rejects the device.

It also determines whether the size of the packet is accepted or not. If requirements exceed
the parameters, then the link control protocol terminates that link.

LAP:

LAP stands for Link access procedure is a data link layer protocol that is used for framing
and transfer the data across point-to-point links.

There are three types of Link access procedure – LAPB ( Link Access procedure balanced),
LAPF ( Link Access Procedure Frame-Mode Bearer Services), and LAPD (Link Access
Procedure D-Channel.

LAP was originally derived from HDLC (High-Level Data Link Control), but was later
updated and renamed LAPB (LAP Balanced).

NCP:

NCP stands for Network control protocol, is a part of the point-to-point protocol. The network
control protocol is used to negotiate the parameter and facilities for the network layer.

For every higher-layer protocol supported by PPP, one NCP is there. IPCP ( Internet Protocol
control protocol), DNCP (DECnet Phase IV Control Protocol), OSINLCP (OSI Network
Layer Control Protocol), IPXCP (Internetwork Packet Exchange Control Protocol), NBFCP
(NetBIOS Frames Control Protocol), IPV6CP (IPv6 Control Protocol) are some of the NCPs.

5.6 HDLC
High-level Data Link Control (HDLC) is a group of communication protocols of the data link
layer for transmitting data between network points or nodes. Since it is a data link protocol,
data is organized into frames. A frame is transmitted via the network to the destination that
verifies its successful arrival. It is a bit - oriented protocol that is applicable for both point - to
- point and multipoint communications.
Transfer Modes

HDLC supports two types of transfer modes, normal response mode and asynchronous
balanced mode.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 Normal Response Mode (NRM) − Here, two types of stations are there, a primary
station that send commands and secondary station that can respond to received
commands. It is used for both point - to - point and multipoint communications.

Asynchronous Balanced Mode (ABM) − Here, the configuration is balanced, i.e. each
station can both send commands and respond to commands. It is used for only point - to -
point communications.

HDLC Frame

HDLC is a bit - oriented protocol where each frame contains up to six fields. The structure
varies according to the type of frame. The fields of a HDLC frame are −

 Flag − It is an 8-bit sequence that marks the beginning and the end of the frame. The
bit pattern of the flag is 01111110.
 Address − It contains the address of the receiver. If the frame is sent by the primary
station, it contains the address(es) of the secondary station(s). If it is sent by the
secondary station, it contains the address of the primary station. The address field may
be from 1 byte to several bytes.
 Control − It is 1 or 2 bytes containing flow and error control information.
 Payload − This carries the data from the network layer. Its length may vary from one
network to another.
 FCS − It is a 2 byte or 4 bytes frame check sequence for error detection. The
standard code used is CRC (cyclic redundancy code)

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

5.7 PPP
Point - to - Point Protocol (PPP) is a communication protocol of the data link layer that is used to
transmit multiprotocol data between two directly connected (point-to-point) computers. It is a
byte - oriented protocol that is widely used in broadband communications having heavy loads
and high speeds.
Components of PPP

Point - to - Point Protocol is a layered protocol having three components −

 Encapsulation Component − It encapsulates the datagram so that it can be

transmitted over the specified physical layer.
 Link Control Protocol (LCP) − It is responsible for establishing, configuring,
testing, maintaining and terminating links for transmission. It also imparts negotiation
for set up of options and use of features by the two endpoints of the links.
 Authentication Protocols (AP) − These protocols authenticate endpoints for use of
services. The two authentication protocols of PPP are −
o Password Authentication Protocol (PAP)
o Challenge Handshake Authentication Protocol (CHAP)
 Network Control Protocols (NCPs) − These protocols are used for negotiating the
parameters and facilities for the network layer. For every higher-layer protocol
supported by PPP, one NCP is there. Some of the NCPs of PPP are −
o Internet Protocol Control Protocol (IPCP)
o OSI Network Layer Control Protocol (OSINLCP)
o Internetwork Packet Exchange Control Protocol (IPXCP)
o DECnet Phase IV Control Protocol (DNCP)
o NetBIOS Frames Control Protocol (NBFCP)
o IPv6 Control Protocol (IPV6CP)

PPP Frame

PPP is a byte - oriented protocol where each field of the frame is composed of one or more bytes.
The fields of a PPP frame are −

 Flag − 1 byte that marks the beginning and the end of the frame. The bit pattern of the
flag is 01111110.
 Address − 1 byte which is set to 11111111 in case of broadcast.
 Control − 1 byte set to a constant value of 11000000.
 Protocol − 1 or 2 bytes that define the type of data contained in the payload field.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 Payload − This carries the data from the network layer. The maximum length of
the payload field is 1500 bytes. However, this may be negotiated between the
endpoints of communication.
 FCS − It is a 2 byte or 4 bytes frame check sequence for error detection. The
standard code used is CRC (cyclic redundancy code)

5.8 Media Access Control

The medium access control (MAC) is a sublayer of the data link layer.
It is responsible for flow control and multiplexing for transmission medium. It controls the
transmission of data packets via remotely shared channels. It sends data over the network
interface card.
5.8.1 MAC Layer in the OSI Model
The Open System Interconnections (OSI) model is a layered networking framework that
conceptualizes how communications should be done between heterogeneous systems. The
data link layer is the second lowest layer. It is divided into two sublayers −
• The logical link control (LLC) sublayer
• The medium access control (MAC) sublayer

5.8.2 MAC Addresses

MAC address or media access control address is a unique identifier allotted to a network interface
controller (NIC) of a device. It is used as a network address for data transmission within a
network segment like Ethernet, Wi-Fi, and Bluetooth. MAC address is assigned to a network
adapter at the time of manufacturing. It is hardwired or hard-coded in the network interface
card (NIC). A MAC address comprises of six groups of two hexadecimal digits, separated by
hyphens, colons, or no separators. An example of a MAC address is 00:0A:89:5B:F0:11.
5.8.3 ALOHA:
ALOHA is a system for coordinating and arbitrating access to a shared communication Networks
channel. A shared communication system like ALOHA requires a method of handling
collisions that occur when two or more systems attempt to transmit on the channel at the
same time. Aloha means "Hello". Aloha is a multiple access protocol at the datalink layer and
proposes how multiple terminals access the medium without interference or collision.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
There are two different versions of ALOHA

Pure ALOHA
• In pure ALOHA, the stations transmit frames whenever they have data to send.
• When two or more stations transmit simultaneously, there is collision and the frames are
destroyed.
• In pure ALOHA, whenever any station transmits a frame, it expects the
acknowledgement from the receiver.
• If acknowledgement is not received within specified time, the station assumes that the
frame (or acknowledgement) has been destroyed.
If the frame is destroyed because of collision the station waits for a random amount of time
and sends it again. This waiting time must be random otherwise same frames will collide
again and again.

• Therefore pure ALOHA dictates that when time-out period passes, each station must wait
for a random amount of time before resending its frame. This randomness will help avoid
more collisions.

• Figure shows an example of frame collisions in pure ALOHA.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
• In fig there are four stations that .contended with one another for access to shared channel.
All these stations are transmitting frames. Some of these frames collide because multiple
frames are in contention for the shared channel. Only two frames, frame 1.1 and frame 2.2
survive. All other frames are destroyed.

• Whenever two frames try to occupy the channel at the same time, there will be a collision
and both will be damaged. If first bit of a new frame overlaps with just the last bit of a frame
almost finished, both frames will be totally destroyed and both will have to be retransmitted.

Slotted ALOHA

• Slotted ALOHA was invented to improve the efficiency of pure ALOHA as chances of
collision in pure ALOHA are very high.

• In slotted ALOHA, the time of the shared channel is divided into discrete intervals called
slots. The stations can send a frame only at the beginning of the slot and only one frame is
sent in each slot.

• In slotted ALOHA, if any station is not able to place the frame onto the channel at the
beginning of the slot i.e. it misses the time slot then the station has to wait until the beginning
of the next time slot.

• In slotted ALOHA, there is still a possibility of collision if two stations try to send at
the beginning of the same time slot as shown in fig.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

• Slotted ALOHA still has an edge over pure ALOHA as chances of collision are reduced
to one-half.
5.9 Ethernet Basics
Ethernet is a set of technologies and protocols that are used primarily in LANs. However,
Ethernet can also be used in MANs and even WANs. It was first standardized in the 1980s as
IEEE 802.3 standard. Since then, it has gone through four generations, as shown in the
following chart

Standard Ethernet has many physical layer implementations. The four main physical layer
implementations are shown in the following diagram

10Base5: Thick Ethernet

 The first implementation is called 10Base5, thick Ethernet, or Thicknet.

 10Base5 was the first Ethernet specification to use a bus topology with an external
transceiver(transmitter/receiver) connected via a tap to a thick coaxial cable.

10Base2: Thin Ethernet

 The second implementation is called 10Base2, thin Ethernet, or Cheapernet.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

 10Base2 also uses a bus topology, but the cable is much thinner and more flexible.
 In this case, the transceiver is normally part of the network interface card (NIC),
which is installed inside the station.

10Base-T: Twisted-Pair Ethernet

 The third implementation is called 10Base-T or twisted-pair Ethernet.

 10Base-T uses a physical star topology. The stations are connected to a hub via two
pairs of twisted cable.

10Base-F: Fiber Ethernet

 Although there are several types of optical fiber 10-Mbps Ethernet, the most
common is called 10Base-F.
 10Base-F uses a star topology to connect stations to a hub.
 The stations are connected to the hub using two fiber-optic cables.

Fast Ethernet (100 Mbps)

Fast Ethernet or 100BASE-T provides transmission speeds up to 100 megabits per second and is
typically used for LAN backbone systems.
The 100BASE-T standard consists of three different component specifications –
1. 100 BASE-TX
2. 100BASE-T4
3. 100BASE-FX

Gigabit Ethernet (1 Gbps)

 The Gigabit Ethernet upgrades the data rate to 1 Gbps(1000 Mbps).
 Gigabit Ethernet can be categorized as either a two-wire or a four-wire implementation.
 The two-wire implementations use fiber-optic cable (1000Base-SX, short- wave, or
1000Base-LX, long-wave), or STP (1000Base-CX).
 The four-wire version uses category 5 twisted-pair cable (1000Base-T).

5.10 CSMA/CD
 Carrier Sense in CSMA/CD means that all the nodes sense the medium to check whether it is
idle or busy.
 If the carrier sensed is idle, then the node transmits the entire frame.
 If the carrier sensed is busy, the transmission is postponed.
 Collision Detect means that a node listens as it transmits and can therefore detect when a frame
it is transmitting has collided with a frame transmitted by another node.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

Transmitter Algorithm in CSMA/CD

 Transmitter Algorithm defines the procedures for a node that senses a busy medium.
 Three types of Transmitter Algorithm exist.
 They are
1. Non-Persistent Strategy
2. Persistent Strategy : 1-Persistent & P-Persistent
Non-Persistent Strategy
 In the non-persistent method, a station that has a frame to send senses the line.
 If the line is idle, it sends immediately.
 If the line is not idle, it waits a random amount of time and then senses the line again.

 The non-persistent approach reduces the chance of collision because it is unlikely that two
or more stations will wait the same amount of time and retry to send simultaneously.
 However, this method reduces the efficiency of the network because the medium
remains idle when there may be stations with frames to send.
Persistent Strategy
1-Persistent :

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

 The 1-persistent method is simple and straightforward.

 In this method, after the station finds the line idle, it sends its frame immediately
(with probability 1).

 This method has the highest chance of collision because two or more stations may find the
line idle and send their frames immediately.
P-Persistent :
 In this method, after the station finds the line idle it follows these steps:
 With probability p, the station sends its frame.
 With probability q = 1 − p, the station waits for the beginning of the next time slot and
checks the line again.

 The p-persistent method is used if the channel has time slots with a slot duration equal to
or greater than the maximum propagation time.
 The p-persistent approach combines the advantages of the other two strategies. It
reduces the chance of collision and improves efficiency
EXPONENTIAL BACK-OFF
 Once an adaptor has detected a collision and stopped its transmission, it waits a
certain amount of time and tries again.
 Each time it tries to transmit but fails, the adaptor doubles the amount of time

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
it waits before trying again.
 This strategy of doubling the delay interval between each retransmission attempt is
a general technique known as exponential back-off.
5.11 Virtual LAN
Virtual Local Area Networks or Virtual LANs (VLANs) are a logical group of computers that
appear to be on the same LAN irrespective of the configuration of the underlying physical
network. Network administrators partition the networks to match the functional requirements
of the VLANs so that each VLAN comprise of a subset of ports on a single or multiple
switches or bridges. This allows computers and devices in a VLAN to communicate in the
simulated environment as if it is a separate LAN.
Types of VLANs

 Protocol VLAN − Here, the traffic is handled based on the protocol used. A switch or
bridge segregates, forwards or discards frames the come to it based upon the traffics
protocol.
 Port-based VLAN − This is also called static VLAN. Here, the network
administrator assigns the ports on the switch / bridge to form a virtual
network.
 Dynamic VLAN − Here, the network administrator simply defines network
membership according to device characteristics.

5.12 Wireless LAN (802.11)

 Wireless communication is one of the fastest-growing technologies.
 The demand for connecting devices without the use of cables is increasing everywhere.
 Wireless LANs can be found on college campuses, in office buildings, and in many public
areas.
ADVANTAGES OF WLAN / 802.11
1. Flexibility: Within radio coverage, nodes can access each other as radio waves
can penetrate even partition walls.
2. Planning : No prior planning is required for connectivity as long as devices follow
standard convention
3. Design : Allows to design and develop mobile devices.
4. Robustness : Wireless network can survive disaster. If the devices
survive,communication can still be established.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
DISADVANTAGES OF WLAN / 802.11
1. Quality of Service : Low bandwidth (1 – 10 Mbps), higher error rates due to
interference, delay due to error correction and detection.
2. Cost : Wireless LAN adapters are costly compared to wired adapters.
3. Proprietary Solution : Due to slow standardization process, many solution are
proprietary that limit the homogeneity of operation.
4. Restriction : Individual countries have their own radio spectral policies. This restricts the
development of the technology
5. Safety and Security : Wireless Radio waves may interfere with other devices. Eg; In
a hospital, radio waves may interfere with high-tech equipment.
TECHNOLOGY USED IN WLAN / 802.11
 WLAN’s uses Spread Spectrum (SS) technology.
 The idea behind Spread spectrum technique is to spread the signal over a wider frequency band
than normal, so as to minimize the impact of interference from other devices.
 There are two types of Spread Spectrum:
 Frequency Hopping Spread Spectrum (FHSS)
 Direct Sequence Spread Spectrum (DSSS)
Frequency Hopping Spread Spectrum (FHSS)
 Frequency hopping is a spread spectrum technique that involves transmitting the signal
over a random sequence of frequencies.
 That is, first transmitting at one frequency, then a second, then a third, and so on.
 The random sequence of frequencies is computed by a pseudorandom number generator.
 The receiver uses the same algorithm as the sender and initializes it with the same seed and
hence is able to hop frequencies in sync with the transmitter to correctly receive the frame.
Direct Sequence Spread Spectrum (DSSS)
 Each bit of data is represented by multiple bits in the transmitted signal.
 DSSS takes a user data stream and performs an XOR operation with a pseudo –random
number.
 This pseudo random number is called as chipping sequence.
TOPOLOGY IN WLAN / 802.11
WLANs can be built with either of the following two topologies /architecture:
 Infra-Structure Network Topology
 Ad Hoc Network Topology
Infra-Structure Topology (AP based Topology)

 An infrastructure network is the network architecture for providing communication between

wireless clients and wired network resources.
 The transition of data from the wireless to wired medium occurs via a Base Station
called AP(Access Point).
 An AP and its associated wireless clients define the coverage area.
Ad-Hoc Topology (Peer-to-Peer Topology)
 An adhoc network is the architecture that is used to support mutual communication between

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
wireless clients.
 Typically, an ad- hoc network is created spontaneously and does not support access
to wired networks.
 An adhoc network does not require an AP.
5.13 Physical Layer
Physical layer in the OSI model plays the role of interacting with actual hardware and signaling
mechanism. Physical layer is the only layer of OSI network model which actually deals with
the physical connectivity of two different stations.
Physical layer provides its services to Data-link layer. Data-link layer hands over frames to
physical layer. Physical layer converts them to electrical pulses, which represent binary
data.The binary data is then sent over the wired or wireless media.
5.13.1 Data and signals
Data or the signal whichever is used in a network, it can be either digital or analog.

Analog and Digital Data

Analog data refers to data that is of continuous format whereas digital data is one which has
discrete states. So the analog data takes continuous values and digital data takes discrete
values. Analog data can be directly converted into an analog signal or sampled and converted
to digital signal. In quite a similar fashion digital data can also be converted to digital signal
or into analog signal after modulation. These are converted so that efficient transmission can
take place.

Analog and Digital Signal

Similar to data, the signals which represent these can also be digital or analog. Analog signals are
known to have many levels of intensity over a given period of time. As the wave moves from
one value to another, along the path it traverses via infinite number of values. Digital signals
rather have only definite set of values. These are represented using a pair of perpendicular
axes. The vertical axis represents the strength of the signal and the horizontal axis gives the
time period.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com

5.13.2 Transmission Media

In data communication terminology, a transmission medium is a physical path between the
transmitter and the receiver i.e. it is the channel through which data is sent from one place to
another. Transmission Media is broadly classified into the following types:

1. Guided Media: It is also referred to as Wired or Bounded transmission media.

Signals being transmitted are directed and confined in a narrow pathway by using
physical links. Features:

 High Speed
 Secure
 Used for comparatively shorter

distances There are 3 major types of Guided

Media:

(i) Twisted Pair Cable –

It consists of 2 separately insulated conductor wires wound about each other. Generally,
several such pairs are bundled together in a protective sheath. They are the most widely used
Transmission Media. Twisted Pair is of two types:

 Unshielded Twisted Pair (UTP):

UTP consists of two insulated copper wires twisted around one another. This type of
cable has the ability to block interference and does not depend on a physical shield for
this purpose. It is used for telephonic applications.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
Advantages:

 ⇢ Least expensive
 ⇢ Easy to install
 ⇢ High-speed capacity

Disadvantages:

 ⇢ Susceptible to external interference

 ⇢ Lower capacity and performance in comparison to STP
 ⇢ Short distance transmission due to attenuation

Applications:

 Used in telephone connections and LAN networks

 Shielded Twisted Pair (STP):

This type of cable consists of a special jacket (a copper braid covering or a foil
shield) to block external interference. It is used in fast-data-rate Ethernet and in voice
and data channels of telephone lines.

Advantages:

⇢ Better performance at a higher data rate in comparison to UTP

⇢ Eliminates crosstalk

⇢ Comparatively faster

Disadvantages:

⇢ Comparatively difficult to install and manufacture

⇢ More expensive

⇢ Bulky

(ii) Coaxial Cable –

It has an outer plastic covering containing an insulation layer made of PVC or Teflon and 2
parallel conductors each having a separate insulated protection cover. The coaxial cable
transmits information in two modes: Baseband mode(dedicated cable bandwidth) and
Broadband mode(cable bandwidth is split into separate ranges). Cable TVs and analog
television networks widely use Coaxial cables.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
Advantages:

 High Bandwidth
 Better noise Immunity
 Easy to install and expand
 Inexpensive

Disadvantages:

 Single cable failure can disrupt the entire network

iii) Optical Fiber Cable –

It uses the concept of refraction of light through a core made up of glass or plastic. The core
is surrounded by a less dense glass or plastic covering called the cladding. It is used for the
transmission of large volumes of data.

 The cable can be unidirectional or bidirectional. The WDM (Wavelength Division

Multiplexer) supports two modes, namely unidirectional and bidirectional mode.

Advantages:

 Increased capacity and bandwidth

 Lightweight
 Less signal attenuation
 Immunity to electromagnetic interference
 Resistance to corrosive materials

Disadvantages:

 Difficult to install and maintain

 High cost
 Fragile

(iv) Stripline

Stripline is a transverse electromagnetic (TEM) transmission line medium invented by Robert

M. Barrett of the Air Force Cambridge Research Centre in the 1950s. Stripline is the earliest
form of the planar transmission line. It uses a conducting material to transmit high-frequency
waves it is also called a waveguide. This conducting material is sandwiched between two
layers of the ground plane which are usually shorted to provide EMI immunity.

(v) Microstripline

In this, the conducting material is separated from the ground plane by a layer of dielectric.

2. Unguided Media:
It is also referred to as Wireless or Unbounded transmission media. No physical medium is
required for the transmission of electromagnetic signals.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
Features:

 The signal is broadcasted through air

 Less Secure
 Used for larger distances

There are 3 types of Signals transmitted through unguided media:

(i) Radio waves –

These are easy to generate and can penetrate through buildings. The sending and receiving
antennas need not be aligned. Frequency Range:3KHz – 1GHz. AM and FM radios and
cordless phones use Radio waves for transmission.

(ii) Microwaves –
It is a line of sight transmission i.e. the sending and receiving antennas need to be properly
aligned with each other. The distance covered by the signal is directly proportional to the
height of the antenna. Frequency Range:1GHz – 300GHz. These are majorly used for mobile
phone communication and television distribution.

(iii) Infrared –
Infrared waves are used for very short distance communication. They cannot penetrate
through obstacles. This prevents interference between systems. Frequency Range:300GHz –
400THz. It is used in TV remotes, wireless mouse, keyboard, printer, etc.

5.13.3 Switching

In large networks, there can be multiple paths from sender to receiver. The switching
technique will decide the best route for data transmission.

Switching technique is used to connect the systems for making one-to-one communication.

Classification Of Switching Techniques

Circuit Switching

 Circuit switching is a switching technique that establishes a dedicated path

between sender and receiver.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 In the Circuit Switching Technique, once the connection is established then the
dedicated path will remain to exist until the connection is terminated.
 Circuit switching in a network operates in a similar way as the telephone works.
 Circuit switching is used in public telephone network. It is used for voice
transmission.
 Fixed data can be transferred at a time in circuit switching technology.
Communication through circuit switching has 3 phases:

 Circuit establishment
 Data transfer
 Circuit Disconnect

Space Division Switches:

 Space Division Switching is a circuit switching technology in which a single

transmission path is accomplished in a switch by using a physically separate set of
crosspoints.

Time Division Switching

The incoming and outgoing signals when received and re-transmitted in a different time slot,
is called Time Division Switching.

Message Switching

 Message Switching is a switching technique in which a message is transferred as

a complete unit and routed through intermediate nodes at which it is stored and
forwarded.
 In Message Switching technique, there is no establishment of a dedicated
path between the sender and receiver.
 The destination address is appended to the message. Message Switching provides a
dynamic routing as the message is routed through the intermediate nodes based on the
information available in the message.
 Message switches are programmed in such a way so that they can provide the most
efficient routes.
 Each and every node stores the entire message and then forward it to the next node.
This type of network is known as store and forward network.
 Message switching treats each message as an independent entity.

Packet Switching

 The packet switching is a switching technique in which the message is sent in one
go, but it is divided into smaller pieces, and they are sent individually.
 The message splits into smaller pieces known as packets and packets are given
a unique number to identify their order at the receiving end.
 Every packet contains some information in its headers such as source
address, destination address and sequence number.
 Packets will travel across the network, taking the shortest path as possible.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 www.BrainKart.
com
 All the packets are reassembled at the receiving end in correct order.
 If any packet is missing or corrupted, then the message will be sent to resend the
message.
 If the correct order of the packets is reached, then the acknowledgment message
will be sent.

Approaches Of Packet Switching:

There are two approaches to Packet Switching:

Datagram Packet switching:

 It is a packet switching technology in which packet is known as a datagram, is

considered as an independent entity. Each packet contains the information about
the destination and switch uses this information to forward the packet to the correct
destination.
 The packets are reassembled at the receiving end in correct order.
 In Datagram Packet Switching technique, the path is not fixed.
 Intermediate nodes take the routing decisions to forward the packets.
 Datagram Packet Switching is also known as connectionless switching.

Virtual Circuit Switching

 Virtual Circuit Switching is also known as connection-oriented switching.

 In the case of Virtual circuit switching, a preplanned route is established before
the messages are sent.
 Call request and call accept packets are used to establish the connection between
sender and receiver.
 In this case, the path is fixed for the duration of a logical connection.

https://play.google.com/store/apps/details?
id=info.therithal.brainkart.annauniversitynotes&hl=en_IN
 Click on Subject/Paper under Semester to
enter. Environmental
Professional English Sciences
Professional and Sustainability -
English - I - - II - HS3252 Discrete GE3451
HS3152
Mathematics
Statistics and Theory of Computation
- MA3354
Numerical - CS3452
Matrices and
Methods - MA3251
Calculus Digital Principles
and Computer Artificial
- MA3151

Semester
Engineering Intelligence and
Semester

Organization
Semester

Graphics Machine Learning

Semester

- CS3351
Engineering - CS3491
Physics - PH3151 - GE3251
Foundation of Data
Physics for Science - CS3352 Database Management

4th
System - CS3492
2nd
1st

Engineering Information
3rd

Chemistry Science
Data Structure -
- CY3151 - PH3256 CS3301 Algorithms - CS3401
Basic Electrical and
Electronics Object Oriented Introduction to
Problem Solving Engineering Operating
Programming -
and Python - BE3251 Systems - CS3451
CS3391
Programming -
GE3151 Programming in C
- CS3251

Computer
Networks - Object Oriented
CS3591 Software
Engineering
- CCS356 Human Values and
Compiler Design - Ethics - GE3791
CS3501 Embedded
Semester

Semester

Systems and IoT - Open Elective 2

Cryptography CS3691
Semester

Project Work /
Semester

and Cyber
Security - Open Elective 3 Intership
CB3491 Open
Open Elective 4
5th

7th

Distributed Elective-1
8th

Computing
6th

Management
- CS3551 Elective-3
Elective
Elective 1 Elective-4

Elective 2 Elective-5

Elective-6
 All Computer Engg [ B.E., M.E., ] (Click on Subjects to
Subjects - enter)

Programming in C Computer Operating Systems

Networks
Programming and Data Programming and Problem Solving and
Structures I Data Python
Structure II Programming
Database Management Computer Analog and Digital
Systems Architecture Communication
Design and Analysis of Microprocessors and Object Oriented
Algorithms Microcontrollers Analysis
and Design
Software Engineering Discrete Internet Programming
Mathematics
Theory of Computation Computer Graphics Distributed Systems
Mobile Computing Compiler Design Digital Signal
Processing
Artificial Intelligence Software Testing Grid and Cloud
Computing
Data Ware Housing and Cryptography and Resource
Data Mining Network Security Management
Techniques
Service Oriented Embedded and Real Multi - Core
Architecture Time Systems Architectures and
Programming
Probability and Queueing Physics for Transforms and
Theory Information Partial Differential
Science Equations
Technical English Engineering Engineering Chemistry
Physics
 Engineering Graphics Total Quality Professional Ethics in
Management Engineering
Basic Electrical and Problem Solving Environmental Science
Electronics and and Python and Engineering
Measurement Engineering Programming