PM/10702/ 4

May 2024

www.bis.gov.in
उत्पाद मैन्यअ
ु ल
हवाई चप्पल – ववविष्ट
IS 10702: 2023 के अनस
ु ार

PRODUCT MANUAL
FOR HAWAI CHAPPAL – SPECIFICATION
ACCORDINGTO IS 10702: 2023

विभिन्न उत्पादों के भलए िारतीय मानक ब्यूरो( अनुरूपता मूलयाांकन )विननयम, 2018 की योजना -I के तहत प्रमाणन के
सांचालन में एकरूपता और पारदभशिता के भलए इस उत्पाद मैनुअल का उपयोग सिी क्षेत्रीय / शाखा कायािलयों और
लाइसेंसधाररयों द्िारा सांदिि सामग्री के रूप में ककया जाएगा। दस्तािेज़ का उपयोग बीआईएस प्रमाणन प्राप्त करने के
इच्छुक सांिावित आिेदकों द्िारा िी ककया जा सकता है I

This Product Manual shall be used as reference material by all Regional/Branch Offices &
licensees to ensure uniformity of practice and transparency in operation of certification under
Scheme-I of Bureau of Indian Standards (Conformity Assessment) Regulations,2018 for various
products. The document may also be used by prospective applicants desirous of obtaining BIS
certification.

1. : IS 10702 : 2023
मानक सांख्या
IS No.
शीर्िक : HAWAI CHAPPAL

Title
:
सांशोधनों की सांख्या 1
No. of amendments
2. नमूना ददशाननदे श
Sampling Guidelines
कच्चा माल Material shall be declared by manufacturer and shall be in
a) Raw material : accordance with Cl 4.1.

Note: This section indicates the requirements for raw material (if
specified in the IS) for which compliance is to be establishedduring
Grant of Licence/Change in Scope of Licence / Factory
Surveillance
b) समूहीकरण ददशाननदे श : Please refer ANNEX – A
Grouping Guidelines
 PM/10702/ 4
May 2024

c) : 4 Pairs
नमूने का पररमाण
Sample Quantity Note: This section indicates the quantity of the sample of the
product and/or the raw material (if applicable), required to be sent
to the laboratory for testing, for the purpose of Grant of
Licence/Change in Scope of Licence/ Factory Surveillance (in case
of market surveillance, effort may be made to procure therequired
quantity of product sample, as far as possible since raw material
sample may not be available in market)

3. परीक्षण उपकरणों की सच
ू ी : Please refer to Annex-B
List of Test Equipment
4. ननरीक्षण और परीक्षण की स्कीम :
Please refer to Annex-C

Scheme of Inspection Note: Please see Cl. 5 of the SIT for Applicability of SIT to
and Testing Small and Micro Scale Enterprises
5. एक ददन में सांिावित परीक्षण
Possible tests in a day
All tests possible on conditioned samples as applicable

Note: This section is for the guidance of BIS Certification Officers/Technical Auditors of BIS
Authorized Outside Surveillance Agencies (OSAs) during factory inspection to provide ready
reference regarding the tests which can be witnessed during the inspection in the factory by the
officer/auditor.
6. लाइसेंस का दायरा /Scope of the Licence:
“Licence is granted to use Standard Mark as per IS 10702 : 2023 with the following scope:
Name of the product HAWAI CHAPPAL
Category, Type and sizes a) Kids (sizes to be declared),
1) Children
2) Infants
and/or;
b) Adult (sizes to be declared)
1) Type 1
2) Type 2
BUREAU OF INDIAN STANDARDS
MANAK BHAVAN,9, BAHADUR SHAH ZAFAR MARG,
NEW DELHI-110002
 PM/10702/ 4
May 2024

ANNEX-A

GROUPING GUIDELINES

As per the Indian Standard, following varieties for HAWAI CHAPPAL may be applicable:
a) Based on use, HAWAI CHAPPAL are divided into the following Category –
a. Kids (Children and infants)
b. Adult
b) Adult Category of Footwear are further classified into two types as given below:
a. Type 1
b. Type 2

The requirement given is relaxed for type 2 Adult Hawai Chappal and relaxed even further for
Kids category of Hawai Chappal when compared with Type 1 adult category Hawai Chappal.
The following Grouping guidelines shall apply for Grant of Licence (GOL)/ Change in Scope
of Licence (CSOL):
Each category (kids and adults) and each Type (Type 1/Type 2 for adults) of any size
may be tested to cover the category and Type for all sizes in the scope of Licence.

All combinations of components and material of footwear within the scope of Licence may
be informed by Licencee to BIS. It shall be responsibility of the manufacturer to ensure
compliance of the footwear with different component and material combination to all the
requirements of the Indian Standard.

If certain materials have already been tested (and footwear made from these materials already
covered in the scope of licence on that basis), new varieties of footwear may be added in the
scope of licence without chemical testing of those materials which have already been tested
before, provided that there is no change in the type/nature of the material and/or the source
of material. In such cases, the manufacturer seeking relaxation from chemical testing for
certain materials, shall declare that there is no change in the type/nature and/or the source of
the materials already tested.

Scope of licence shall be restricted based on the manufacturing and testing facilities (if
applicable) available.

During operation of licence, samples of each variety covered in the scope of licence, shall
be testedin rotation, to the extent possible
 PM/10702/ 4
May 2024

ANNEX – B

LIST OF TEST EQUIPMENTS

(INDICATIVE LIST, FOR GUIDANCE ONLY)
Sr. Tests used in with Clause Test Equipment
No. Reference
1 Length (Cl 4.2) Steel scale/ Vernier Calipers
2 Thickness of sole (Cl 4.3) Dial Gauge / Thickness Gauge, vernier Caliper
Compression set (Cl. 4.4, Thickness gauge , Conditioning chamber capable of
3 Table 1, Sl no i) maintaining oven, compression testing apparatus,
rotating circular cutter
Split tear strength (Cl. 4.4, Steel scale/Vernier calipers , Tensile testing machine (
4 Table 1, Sl no ii) Capable of rate of traverse of 75 mm/min)
shrinkage test at (Cl. 4.4, Steel scale/Vernier calipers (LC-0.1mm) ,
Table 1, Sl no iii) Conditioning chamber capable of maintaining 65 ±5
5
% RH and 27 ±2 oC temperature, Hot air
oven,
Abrasion Resistance (Cl. 4.4, abrasion machine as per 5.1 of IS 3400 (Part 3), abrasive
Table 1, Sl no iv) sheet, Hollow drill, balance, standard reference
6 compounds. Conditioning chamber, arrangement for
keeping ambient temperature, standard reference
compounds
Flexing Resistance (Cl. 4.4, Ross flexing machine as per IS 3400 (Part 16),
Table 1, Sl no v) piercing tool and holder, rule, thickness guage, soap,
7
conditioning chamber, cold chamber, arrangement to
maintaining temp of 27 +/-2
Hydrolysis Resistance (Cl. 4.4, As per IS 15298 (Part 1)
8
Table 1, Sl no vi)
Breaking strength, Elongation Steel scale/Vernier caliper, Conditioning chamber capable
At Break (Cl 4.4,Table 2 Sl no i) of maintaining 65 ±5 % RH and 27 ±2 oC temperature ,
9
Tensile testing machine ( Capable of rate of traverse of
500 mm/min)
Toe Post Attachment Tensile testing machine with jaw separation speed
Strength, (Cl 4.4,Table 3 of100 mm/min ± 10 mm/min, twist drill bit, conditioning
10 Sl no i) and Attachment chamber, template, wire loops
Strength Of Rear Strap,
(Cl 4.4,Table 3 Sl no ii)
Inter Layer Bond Strength, (Cl Tensile testing machine as per 5.2.2 of IS 15298
11 4.4,Table 3 Sl no iii) (Part1)
CHEMICAL REQUIREMENT As per IS 17011 for critical substance category I and
FOR HAWAI CHAPPAL(Cl. category II as specified under 3.6 of the IS
12
4.4, Table 1, Sl no vii, Table
2, Sl no ii)
Lead Content (Cl. 4.4, Table 1, Nessler cylinders, P-Nitrophenol indicator Sol, Dil
13 Sl no vii, Table 2, Sl no ii) Hydrochloric acid, hydrogen sulphide solution, Standard
lead solution, whatman filter paper
 PM/10702/ 4
May 2024

ANNEX C

SCHEME OF INSPECTION AND TESTING

1. QUALITY ASSURANCE PLAN

1.1 It is expected that manufacturers (licensees/applicants) will implement a Quality Assurance Plan
i.e. a plan of regular testing and in-process controls, designed to ensure that the product bearing the
Standard Mark conforms to all requirements of the Indian Standard.

1.2 The manufacturers shall define a Quality Assurance Plan defining the control unit (i.e. lot/batch
etc.) and the levels of control (i.e. the frequency and number of samples for conducting the different
tests as per the Indian Standard) and submit the same to BIS Branch Office for information. The
manufacturer shall comply with the same and maintain test records in accordance with para 2.4.

1.3 RECOMMENDED LEVELS OF CONTROL/CONTROL UNIT:

1.3.1 For the guidance of manufacturers, the recommended definition of control unit is : 50,000 pairs
or Fortnight production (whichever is earlier), of Hawai Chappal of same combination of materials,
manufactured from the same raw material

1.3.2 For the guidance of manufacturers in preparing the Quality Assurance Plan, recommended
levels of control are given in Table 1.

1.3.3 The manufacturer shall ensure inspection and testing as per the Quality Assurance Plan
submitted by them on the whole production of the factory which is covered by this plan. Alternatively,
the manufacturer has the option of adherence to the quality plan as per levels of control recommended
in column 3 of Table 1.

1.4 However, all manufacturers shall ensure compliance of their products to all the requirementsof
the Indian Standard.
2. ENSURING COMPLIANCE THROUGH TESTING- It is expected that manufacturers
(licensees/applicants) will establish a suitably equipped and staffed in house laboratory (In house
testing facility) for testing at least those parameters of the Indian Standard which require routine testing
for ensuring quality of the product. This includes in-process controls as may be defined and put in
place by the manufacturer and testing parameters/requirements which can only be performed in the
factory.

2.1 For the guidance of manufacturers, Table 1 giving the recommended levels of control is given
below. Column 2 of Table 1 indicates routine tests where test equipment is required in house as “R”
or other tests which can be subcontracted as “S”. Subcontracting is permitted to BIS
recognized/empanelled laboratory or any other laboratory having valid NABL accreditation as per
IS/ISO/IEC 17025.

2.2 For MSME manufacturers, the requirement of maintaining a laboratory/in-house testing

facility for routine tests (indicated as “R” in Column 2 of Table 1) is also optional.

2.2.1 MSME manufacturers may utilize common cluster based facilities as per guidelines for the
utilization of cluster based test facilities by MSMEs or the provisions of Sharing of testing facilities or
get testing done from BIS recognized/empaneled laboratory or any other laboratory having validNABL
accreditation as per IS/ISO/IEC 17025.
 PM/10702/ 4
May 2024

2.3 Large Scale manufacturers shall maintain an in-house laboratory equipped at least withtest
facilities for routine tests (indicated as “R” in Column 2 of Table 1), where different testsgiven in
the specification shall be carried out in accordance with the method given in the specification. They
shall also implement a calibration plan for the in-house test equipment.
2.3.1 Alternatively, in lieu of an in-house laboratory, large scale manufacturers can also utilize the
provisions of Sharing of testing facilities as per the Guidelines for Grant of Licence available on BIS
website www.bis.gov.in. (Under Conformity Assessment>Product Certification Process). Even for
subcontracted tests, provisions for sharing of testing facilities can be utilized.

2.4 TEST RECORDS- The manufacturers maintaining an in-house laboratory or utilizing common
cluster based facilities or shared test facilities shall maintain test records for the tests carried out to
establish conformity. For the tests being subcontracted to BIS recognized/empanelled laboratoryor any
other laboratory having valid NABL accreditation as per IS/ISO/IEC 17025, test reports issued by the
laboratories shall be available for inspection by BIS.

3. PACKING AND MARKING - The Standard Mark as given in the Schedule of the licence shall be
incorporated legibly and indelibly on each Hawai Chappal for each pair, provided always that the
material so marked conforms to each requirement of the specification.

3.1 Packing and Marking shall be done as per the Indian Standard. Kids hawai chappal shall be marked
as ‘0’ whereas infants hawai chappal shall be marked as ‘00’ for Type

3.2 Additional Marking requirements: The material shall also be marked (through tags/stickers or
otherwise) with the following additional requirement on the package/Product (in case only bulk
packaging is done):

a) “For BIS certification details please visit www.bis.gov.in”

4. REJECTION - All the production which conforms to the Indian Standard and covered under the
scope of this licence shall be marked with the Standard Mark. Disposal of non-conforming product
shall be done in such a way so as to ensure that there is no violation of provisions of BIS Act, 2016.

5. Applicability of SIT for Small and Micro Enterprises (SMEs):

5.1 Compliance to the Scheme of Inspection and Testing is OPTIONAL for Micro, and Small Scale
Units with respect to the requirements for Clause 1(Quality Assurance Plan), Clause 2 (Ensuring
Compliance through Testing). However, ALL units shall ensurecompliance of their products to
the requirements of the Indian Standard.

5.2 The requirements of SIT with respect to Clause 3 (Packing and Marking) and Clause 4 (Rejection)
shall be followed by all.
 PM/10702/ 4
May 2024

TABLE 1
(ONLY FOR GUIDANCE PURPOSE)

(1) (2) (3)

Test Details Test equipment Levels of
requirement Control
Clause Requirement Test Methods R: required (or) S: Sub- No. of Frequency Remarks
Clause Reference IS contracting Sampl
permitted e
4.1.1, Firm to have adequate in-process Each consignment if
4.1 Material 4.1.2, 4.1.3, IS 10702 : 2023 R controls to check compliance of this components are
& 4.1.4 parameter given in the Indian bought
Standard. However, appropriate Recommendary as
4.2 Length 4.2 IS 10702 : 2023 R records shall be maintained by the per Cl 4.2 of IS
10702:2023
manufacturer for evidence of
4.3 Thickness 4.3.1 IS 10702 : 2023 R conformity
4.4, Table 1 Physical Requirement Of Bottom Material For Hawai Chappal
i) Compression Set Annex D IS 10702 : 2023 S one Once in a month
one -do- Applicable for Adult
ii) Split Tear Strength, Annex-E IS 10702 : 2023 S
category Type 1 only
Shrinkage,
iii) Applicable for Adult
Polymeric Material Annex-F IS 10702 : 2023 S one -do-
category
Shrinkage, Rubber,
one Once in three Applicable for Adult
months or each category
Abrasion consignment (If
iv) - IS 3400 (Part 3) S
Resistance components are
bought) whichever
is earlier
v) Flexing Resistance: - IS 3400 : Part 16 S one -do-
one -do- 1. Applicable for
Adult category
Hydrolysis Type 1 only
vi) - IS 15298 (Part 1) S
Resistance, 2. applicable only for
polyester based
PU bottom
 PM/10702/ 4
May 2024

1. The bottom (only

in contact with
skin) of hawai
chappal shall
comply with Table
1 of IS 17011 for
critical substance
Chemical Category 1 and
Each consignment of
vii) requirement for - Table 1 Of IS 17011 S one raw material
Category 2
hawai Chappal 2. Test
Certificate/report
should be
obtained either
from supplier or
from any
independent
Laboratory
1. Applicable for Kids
category and Type
1 of adult category
2. Only In case of
PVC material
3. Test
Each consignment of
viii) Lead Content. - IS 12240 (Part 5). S one raw material
Certificate/report
should be
obtained either
from supplier or
from any
independent
Laboratory
4.4 Table 2, Physical Requirement Of Strap Material For Hawai Chappal
Breaking Strength,
Strap To Strap
Toe portion to strap
i) 1. Applicable for
Annex ‘G’ IS 10702 : 2023 S one Each control unit Adult category
Elongation At
Type 1 only
Break, 2. applicable to strap
to strap (V shape)
 PM/10702/ 4
May 2024

1. The strap of hawai

chappal shall
comply with Table
1 of IS 17011 for
critical substance
Category 1 and
Chemical Category 2
Each consignment of
ii) requirement for - Table 1 Of IS 17011 S one raw material
2. Test
hawai Chappal Certificate/report
should be
obtained either
from supplier or
from any
independent
Laboratory
1. Applicable for
Kids category and
Type 1 of adult
category
2. Test
Each consignment of Certificate/report
iii) Lead Content. - IS 12240 (Part 5). S one raw material should be
obtained either
from supplier or
from any
independent
Laboratory
4.4, table 3 Attachment Strength And Inter Layer Bond Strength Requirement For Hawai Chappal
Toe Post
i) Attachment S one Each control unit
Strength,
Annex H IS 10702 : 2023
Attachment
ii) Strength Of Rear S one -do-
Strap,
applicable only for
Inter Layer Bond
iii) - IS 15298 : Part 1 S one -do- multilayer pasted
Strength, stuck-on bottom sole