December 2013

DIN 929
D
ICS 21.060.20 Supersedes
DIN 929:2013-05

Hexagon weld nuts,

English translation of DIN 929:2013-12

Sechskant-Schweißmuttern,
Englische Übersetzung von DIN 929:2013-12
Écrous hexagonaux à souder,
Traduction anglaise de DIN 929:2013-12

Document comprises 10 pages

Translation by DIN-Sprachendienst.
In case of doubt, the German-language original shall be considered authoritative.

© No part of this translation may be reproduced without

hasfür
Copyright Deutsches Institut theNormung
exclusive
prior permission of
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

DIN Deutsches Institut für Normung e. V., Berlin. Beuth Verlag GmbH, 10772 Berlin, Germany,
e. V. right of sale for German Standards (DIN-Normen).
www.din.de !%+ÑL"
Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957 www.beuth.de 01.14 2089641
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

A comma is used as the decimal marker.

Contents
Page
Foreword ......................................................................................................................................................... 3
1 Scope ................................................................................................................................................. 4
2 Normative references ....................................................................................................................... 4
3 Dimensions ........................................................................................................................................ 5
4 Technical delivery conditions ......................................................................................................... 7
5 Designation ....................................................................................................................................... 8
6 Marking .............................................................................................................................................. 8
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

7 Representation in drawings............................................................................................................. 8
8 Connecting dimensions ................................................................................................................... 8
Bibliography ................................................................................................................................................. 10

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

Foreword
This standard has been prepared by Working Committee NA 067-00-03 AA Verbindungselemente mit
metrischem Innengewinde of the Normenausschuss Mechanische Verbindungselemente (FMV) (Fasteners
Standards Committee).

The DIN 929:1972-12 edition assigned the property class 8 to hexagon weld nuts, adding ‘weldable’. Since
then, proof loads for nuts have been increased and new nut heights specified in international (and European)
specifications (see DIN EN ISO 898-2).

Neither in this nor in the previous revision of this standard did it seem advisable to increase the height of weld
nuts and thus harmonize it with the calculation basis for nuts with full loadability, since weld nut mounting is
largely automated. Changing nut dimensions would have caused major difficulties which would not have been
outweighed by a slightly greater resistance to stripping.

Therefore, this latest edition of this standard leaves nut dimensions unchanged, without specifying property
classes. Instead, it only specifies steel with a maximum carbon content of 0,25 % and relevant proof loads.
The proof loads of weld nuts specified in this standard are deemed sufficient to form fully loadable screw
connections with bolts of a property class < 8.8. Weld nuts with a higher loadability are specified in
DIN EN ISO 21670.

The DIN 4000-161-5 tabular layout of product properties applies to weld nuts covered by this standard.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. DIN shall not be held responsible for identifying any or all such patent rights.

Amendments

This standard differs from DIN 929:2000-01 as follows:

a) normative references have been updated;

b) in Table 1 and Table 4, the number of positions after the decimal comma has been harmonized;

c) according to DIN ISO 965-1, symbol d1 has been changed to D;

d) symbols d2 to d5 have been changed to d1 to d4;

e) Table 2 replaces 4.1 to 4.3, 4.5 and 4.6;

f) the standard has been editorially revised.

DIN 929:2013-05 contained an error that has been corrected as follows:

a) In Table 1, the limit deviations for h1 and h2 included in the standard preceding the May 2013 edition
have been re-included.

Previous editions

DIN 929: 1965-09, 1972-12, 1983-08, 1987-09, 1998-02, 2000-01, 2013-05

3
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

1 Scope
This document specifies requirements for hexagon weld nuts with coarse metric threads from sizes M3 to M16
and with fine pitch metric threads with nominal diameters from 8 mm to 16 mm in product grade A.

According to DIN EN ISO 898-1, weld nuts specified in this standard are suitable for connection with bolts of
property class < 8.8.

This standard does not apply to hexagon weld nuts with flange as specified in DIN EN ISO 21670.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.

DIN 13-1, ISO general purpose metric screw threads — Part 1: Nominal sizes for coarse pitch threads —
Nominal diameter from 1 mm to 68 mm

DIN 13-5, ISO general purpose metric screw threads — Part 5: Nominal sizes for 1 mm and 1,25 mm fine
pitch threads — Nominal diameter from 7,5 mm to 200 mm

DIN 13-6, ISO general purpose metric screw threads — Part 6: Nominal sizes for 1,5 mm fine pitch threads —
Nominal diameter from 12 mm to 300 mm

DIN 267-2, Fasteners — Technical delivery conditions — Design and dimensional accuracy

DIN EN ISO 898-1, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts,
screws and studs with specified property classes — Coarse thread and fine pitch thread

DIN EN ISO 898-2, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Bolts,
screws and studs with specified property classes — Coarse thread and fine pitch thread

DIN EN ISO 3269, Fasteners — Acceptance inspection

DIN EN ISO 4042, Fasteners — Electroplated coatings

DIN EN ISO 4759-1, Tolerances for fasteners — Part 1: Bolts, screws, studs and nuts — Product grades A, B
and C

DIN EN ISO 21670, Hexagon weld nuts with flange

DIN ISO 965-1, ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data

DIN ISO 8992, Fasteners — General requirements for bolts, screws, studs and nuts

ASME B 1.1, Unified Inch Screw Threads (UN and UNR Thread Form) 1)

1) Obtainable from Beuth Verlag GmbH (Foreign Standards Service), 10772 Berlin, Germany.
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

3 Dimensions
Hexagon weld nuts, with the exception of welding projections, do not need to be designed as shown in Figure
1, however, their dimensions shall be as specified in Table 1.

Dimensions in millimetres

Figure 1 — Dimensions (notation)

--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

Table 1 — Dimensions

Dimensions in millimetres
Thread size b d1 d2 d3 ea
D D × Pb Limit
d11 H13 max. min.
deviations
M3 – – 0,80 4,50 4,50 3,15 8,15
M4 – – 0,80 ±0,2 6,00 6,00 4,20 9,83
M5 – – 0,80 7,00 7,00 5,25 10,95
M6 – – 0,90 ±0,22 8,00 8,00 6,30 12,02
M8 M8 × 1 – 1,00 ±0,25 10,50 10,50 8,40 15,38
M10 M10 × 1,25 M10 × 1 1,25 12,50 12,50 10,50 18,74
– – 7/16-20 UNF-2Bc 1,25 12,50 13,50 11,70 18,74
±0,3
– – 7/16-20 UNF-2Bc 1,25 13,50 13,50 11,70 20,91
M12 M12 × 1,25 M12 × 1,5 1,25 14,80 14,80 12,60 20,91
(M14) (M14 × 1,5) – 1,50 ±0,4 16,80 16,80 14,70 24,27
M16 M16 × 1,5 – 1,50 18,80 18,80 16,80 26,51

Mass
h1 h2 m s (7,85 kg/dm3)
Thread size
kg per 1 000
units
D D × Pb Limit Limit
h14 h13 ≈
deviations deviations

M3 – – 0,55 0,25 3,0 7,5 0,78

0
M4 – – 0,65 0,35 0 3,5 9,0 1,13
-0,1
M5 – – 0,70 0,40 -0,1 4,0 10,0 1,73
M6 – – 0,75 0 0,40 5,0 11,0 2,50
M8 M8 × 1 – 0,90 -0,15 0,50 6,5 14,0 5,27
0
M10 M10 × 1,25 M10 × 1 1,15 0,65 -0,15 8,0 17,0 9,58
– – 7/16-20 UNF-2Bb 1,15 0,65 10,0 17,0 12
– – 7/16-20 UNF-2Bb 1,40 0 0,80 10,0 19,0 14
-0,2 0
M12 M12 × 1,25 M12 × 1,5 1,40 0,80 -0,2 10,0 19,0 13,7
(M14) (M14 × 1,5) – 1,80 1,00 11,0 22,0 21,3
(M16) (M16 × 1,5) – 1,80 1,00 13,0 24,0 28,5
Bracketed sizes should be avoided if possible.
a emin = 1,12 smin
b P is the thread pitch.
c According to ASME B 1.1; only for the fitting of safety belts in motor vehicles.

6
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

4 Technical delivery conditions

See Table 2.

Table 2 — Technical delivery conditions

Material Steel (St) with a maximum carbon mass of 0,25 %a

General
Standard DIN ISO 8992
requirements
Tolerance class 6G
Thread
Standard DIN 13-1, DIN 13-5, DIN 13-6, DIN ISO 965-1

Mechanical Proof loads See Table 3.

properties Proof load test DIN EN ISO 898-2
Limit Product grade A
deviations,
geometrical Standard DIN EN ISO 4759-1, DIN 267-2
tolerances
Plain
DIN EN ISO 4042 applies with regard to electroplating.
Surface finish — Coating Plain weld nuts may already be affected by corrosion during storage
or transportation. It is the manufacturer’s responsibility to take
protective measures against corrosion during transportation without
impairing nut weldability.
Acceptance inspection DIN EN ISO 3269 applies with regard to acceptance inspection.
a Other steel qualities shall be subject to agreement.

If the proof load test is carried out according to DIN EN ISO 898-2, the loads given in Table 3 apply. In case of
dispute, welding projections shall be removed prior to testing.

Table 3 — Proof loads

Coarse thread Proof load Fine pitch thread Proof load

D in N D×P in N
M3 3 800 – –
M4 6 800 – –
M5 11 000 – –
M6 15 500 – –
M8 28 300 M8 × 1 30 200
M10 44 800 M10 × 1 50 200
– – M10 × 1,25 47 800
– – 7/16-20 UNF-2B 53 600
M12 65 300 M12 × 1,25 72 100
– – M12 × 1,5 68 200
M14 89 700 M14 × 1,5 97 500
M16 123 000 M16 × 1,5 132 000

7
--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

5 Designation
Designation of an M10 hexagon weld nut, made of steel (St):

Weld nut DIN 929 – M10 – St

For hexagon weld nuts with UNF thread the relevant width across flats is to be added to the designation.

Designation of a hexagon weld nut with 7/16-20 UNF-2B thread and a width across flats of 17 mm (SW17),
made of steel (St):

Weld nut DIN 929 – 7/16-20 UNF-2B – SW17 – St

6 Marking
Hexagon weld nuts of thread sizes M5 and above are to be marked with the manufacturer’s symbol by
indenture to a spot at the discretion of the manufacturer.

7 Representation in drawings
See Table 2.

Figure 2 — Representation in drawings

8 Connecting dimensions

See Figure 3 and Table 4.

--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

Figure 3 — Connecting dimensions (Nut not welded on) (notation)

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

Table 4 — Connecting dimensions

Dimensions in millimetres
Thread size as in Table 1 Sheet thickness a Hole diameter d4
D D×P min. max. H11
M3 – – 0,63 1,5 4,5
M4 – – 0,75 1,5 6,0
M5 – – 0,88 2,0 7,0
M6 – – 0,88 2,5 8,0
M8 M8 × 1 – 1,00 3,0 10,5
M10 M10 × 1,25 M10 × 1 1,25 4,0 12,5

--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---
– – 7/16-20 UNF-2B 1,25 4,0 13,5
M12 M12 × 1,25 M12 × 1,5 1,50 5,0 14,8
M14 M14 × 1,5 – 2,00 6,0 16,8
M16 M16 × 1,5 – 2,00 6,0 18,8

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT
 DIN 929:2013-12

Bibliography

DIN 4000-161, Tabular layout of product properties — Part 161: Fasteners with internal thread

--`,`,,`,``,`````,``,`,``,`,```-`-`,,`,,`,`,,`---

10

Copyright Deutsches Institut für Normung e. V.

Provided by IHS Markit under license with DIN Sold to:Bulten ltd, 1012957
No reproduction or networking permitted without license from IHS Not for Resale,06/08/2021 04:20:44 MDT