Service Repair Manual

Models

329D L Excavator
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 3/12

Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 154-6181 Forcing Screw 1
D 138-7574 Link Bracket 2
5F-7366 Forcing Screw 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
E 1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F 1U-8846 Gasket Sealant 1

Start By:

a. Remove the final drive. Refer to Disassembly and Assembly, "Final Drive - Remove".

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.

1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the part's original locations.

Illustration 1 g00708089

2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 4/12

3. Remove bolts (1) and the washers that hold the cover in position.

Illustration 2 g00708090

4. Remove the setscrews from the cover. Fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).

Illustration 3 g00708091

5. Remove thrust plate (3) from cover (2).

6. Remove plugs (4) from cover (2).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
https://www.ebooklibonline.com

Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.

https://www.ebooklibonline.com
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 5/12

Illustration 4 g00708235

7. Remove O-ring seals (5) from both plugs (4) that were in the cover.

Illustration 5 g00708092

8. Remove spacer (6) from carrier assembly (7).

9. Remove sun gear (8) from carrier assembly (7).

10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).

Illustration 6 g01304883

11. Disassemble carrier assembly (7), as follows.

a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 6/12

Illustration 7 g00708144

b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.

c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.

Illustration 8 g00708218

d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.

e. Remove bearing (12) from planetary gear (13).

12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 7/12

Illustration 9 g00708162

13. Remove sun gear (14) from carrier assembly (15).

Illustration 10 g00708325

14. Remove spacer (16).

Illustration 11 g00708184

Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.

15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 8/12

Illustration 12 g00708360

16. Use a screwdriver or a chisel in order to separate the two ring gears (17).

Note: The two ring gears are held together with Tooling (F). It may be necessary to heat the
ring gears in order to soften the sealant. Do not heat over 135 °C (275 °F) for more than
thirty minutes.

Illustration 13 g00708172

17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).

18. Fasten a suitable lifting device to the shackle.

19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).

20. Disassemble carrier assembly (15), as follows.

Illustration 14 g00708175

a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 9/12

Illustration 15 g00708370

Illustration 16 g00708220

b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.

c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.

d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.

e. Remove bearings (22) from planetary gear (23).

21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 10/12

Illustration 17 g00708186

22. Remove O-ring seal (24) from main housing (18).

Illustration 18 g00708187

23. Remove bolts (25) from gear (26).

Illustration 19 g00708202

24. Use Tooling (C) in order to remove gear (26) from main housing (18).

Note: The motor housing will separate from the main housing (18) once gear (26) is
removed. Make sure that the motor housing is supported.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 11/12

Illustration 20 g00708211

25. Remove shims (27) from the main housing.

Illustration 21 g00708212

26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.

27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from the motor housing (28). The combined weight of main housing (18) and the
final drive sprocket is approximately 82 kg (180 lb).

Illustration 22 g00708214

28. Remove Duo-Cone seal (29) from motor housing (28).

29. Remove alignment pins (30).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 12/12

Illustration 23 g00708215

Illustration 24 g00708216

30. Remove Duo-Cone seal (31) from main housing (18).

31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.

32. If necessary, remove the final drive sprocket from the main housing.

33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".

Copyright 1993 - 2019 Caterpillar Inc. Wed Nov 27 23:47:31 UTC+0800 2019
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 3/13

Tool Part Number Part Description Qty

A 1P-2420 Transmission Repair Stand 1
B 138-7573 Link Bracket 2
C 1P-1863 Retaining Ring Pliers 1
D 138-7575 Link Bracket 3
E 4C-8359 Eyebolt 2
F 138-7574 Link Bracket 2
G 138-7576 Link Bracket 2

Start By:

a. Start by removing the final drive. Refer to Disassembly and Assembly, "Final Drive -
Remove".

Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of
the component should be thoroughly cleaned. This will prevent dirt from entering the
internal mechanism.

1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled to the original locations.

Illustration 1 g00892878

2. Use Tooling (G) and a suitable lifting device to position the final drive assembly onto
Tooling (A). The weight of the final drive assembly is approximately 550 kg (1200 lb).

3. Remove bolts (1).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 4/13

Illustration 2 g00892883

4. Use Tooling (B) and a suitable lifting device to remove cover (2). The weight of cover (2) is
approximately 32 kg (70 lb).

Illustration 3 g00892888

5. Remove bolts (3) and gear (4). Check plate (6). Replace plate (6) if plate (6) is worn.
Remove plugs (5) from cover (2).

Illustration 4 g00892906

6. Remove O-ring seals (7) from plugs (5).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 5/13

Illustration 5 g00892930

7. Remove gear (8) and spacer (9).

Illustration 6 g00892965

8. Use Tooling (C) to remove retaining ring (10). Remove washer (11) and gear (12). Remove
bearing assembly (13) and washer (14).

9. Repeat Step 8 for the other two gear assemblies.

Illustration 7 g00892968

10. Remove retaining ring (15).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 6/13

Illustration 8 g00892975

11. Remove carrier assembly (16).

Illustration 9 g01389804

12. Use a suitable press to remove the shafts from carrier assembly (16).

Illustration 10 g00892977

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 7/13

13. Remove gear (17) and spacer (18).

Illustration 11 g00892997

14. Use Tooling (D) and a suitable lifting device to remove planetary carrier (19). The weight of
planetary carrier (19) is approximately 48 kg (105 lb).

Illustration 12 g00893019

15. Remove retaining ring (21). Lift planetary carrier (19) off sun gear (20).

Illustration 13 g00896860

16. Drive spring pin (23) into planetary shaft (22).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 8/13

Illustration 14 g00893043

17. Remove planetary shaft (22). Use a suitable punch to remove spring pin (23) from planetary
shaft (22).

Illustration 15 g00896863

18. Remove washers (24) and bearing (25) from planetary gear (26).

19. Repeat Steps 16 through 18 for the other two planetary gears.

Illustration 16 g01842853

20. Remove gear (27). Remove spacer (27A).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP549... 9/13

Illustration 17 g01842974

21. Use two people to remove carrier assembly (28). The weight of carrier assembly (28) is
approximately 38 kg (85 lb).

Illustration 18 g01843140

22. Drive spring pin (30) into shaft (29).

Illustration 19 g00893658

23. Remove shaft (29). Use a suitable punch to remove spring pin (30) from shaft (29).

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 10/13

Illustration 20 g00893674

24. Remove washers (31) and bearings (32) from planetary gear (33).

25. Repeat Steps 22 through 24 for the other three planetary gears.

Illustration 21 g01208300

26. Fasten Tooling (E) and a suitable lifting device to ring gear (34), as shown. Remove ring
gear (34) from sprocket housing (35). The weight of ring gear (34) is approximately 66 kg
(146 lb).

Illustration 22 g01208542

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 11/13

27. Remove O-ring seal (36) from sprocket housing (35).

Illustration 23 g01208553

28. Remove bolts (37) from coupling gear (38).

Illustration 24 g01208572

29. Install suitable forcing bolts (39) in coupling gear (38). Tighten the forcing bolts evenly in
order to loosen coupling gear (38). Remove the coupling gear from the motor housing.

Illustration 25 g01208578

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 12/13

Illustration 26 g01208625

30. Remove shims (40) from the motor housing.

Note: Inner cones and outer bearing cones (42) are a slip fit on the motor housing. While
you remove sprocket housing (35) from the motor housing, inner bearing cone (42) may
stay with the sprocket housing or the inner bearing cone may stay on the motor housing.

31. Fasten Tooling (F) and a suitable lifting device to sprocket housing (35). Separate the
sprocket housing from the motor housing. The weight of sprocket housing (35) is
approximately 109 kg (240 lb).

Illustration 27 g01208626

32. Remove the locating pins from the motor housing.

33. Remove Duo-Cone seal (41) from the motor housing.

34. If inner bearing cone (42) remained on the motor housing, then remove the inner bearing
cone.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
329D L Excavator CZF00001-UP (MACHINE) POWERED BY C7 Engine(SEBP5... 13/13

Illustration 28 g01208633

35. Remove Duo-Cone seal (43) from the sprocket housing.

36. If inner bearing cone (42) remained on the sprocket housing, then remove the inner bearing
cone.

37. Remove the bearing cups from the sprocket housing.

Copyright 1993 - 2019 Caterpillar Inc. Wed Nov 27 23:48:27 UTC+0800 2019
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2019/11/27
https://www.ebooklibonline.com

Hello dear friend!

Thank you very much for reading.
Enter the link into your browser.
The full manual is available for immediate
download.

https://www.ebooklibonline.com