1.

What is mean by compliant

coating?
 a. Coating which applied on specified atmosphere condition
 b. Coating which suitable with the requirements of the
EPA
 c. Coating which suitable for the steel substrate
 d. Coating with non compliance report
2.

Which situation is expressed as

damp surface?
 a. Surface with detectable water
 b. Surface temperature below dew point
 c. Surface with a noticeable film of water
 d. Surface temperature above dew point
3.

Which information is not available

in MDS?
 a. Flash point
 b. Dew point
 c. VS%
 d. Recommended Thinner
4.

Who is having duty of Safety on a

Working site?
  a. HSE (Health & safety executive)
 b. Contractor
 c. Engineer
 d. Employees
5.

___________ used to detect the

voltage in Impressed current
system
 a. National Grid
 b. Transformer Rectifier
 c. Copper/Copper Sulphate half cell electrode
 d. Sodium Chloride
6.

A Coating continues protection of

7 years, Which falls in
_____________
 a. Long term protection
 b. Medium term protection
 c. Short term protection
 d. Fixed term protection
7.

In dragger tube number specified

is n=5,what is RAQ
 a. 500 ppm
 b. 5 rpm
 c. 500 cfm
  d. 500 cc
8.

A Galvanized substrate with oxide

layer has formed called
 a. New Galvanising
 b. Weathered Galvanising
 c. Unsuitable galvanizing
 d. Previously painted Galvanising
9.

A primer used for pretreatment for

zinc metal surfaces.
 a. Zinc rich epoxy
 b. T.Wash
 c. FBE
 d. Zinc Phosphate
10.

PA 10 specification is suitable for

use in the following area:
 a. Onshore installations
 b. offshore installations
 c. internal coatings of pipes
 d. below ground (buried)
11.

After applying primer on steel

surface, Paint got wetted by
raining. As a painting inspector
what you do?
 a. Wait for water to dry
 b. Blast to remove existing primer, recoat
 c. Continue next stage after rain
 d. Recoat primer without removing existing coat
12.

Who is having permission to

change a specified paint system?
 a. Paint technologist
 b. Painting inspector
 c. Engineer
 d. Contractor
13.

Which surfaces comes on hot duty

surfaces?
 a. Metal surfaces attaining a temperature above 340o C
 b. Metal surfaces attaining a temperature above 100o C.
 c. Metal surfaces attaining a temperature above 37o C
 d. Metal surfaces attaining a temperature above 540o C
14.

At which temperature aluminium

melts
 a. 100 oC
 b. 240 oC
  c. 425 oC
 d. 625 oC
15.

A Multi component paint dried by

 a. Solvent evaporation
 b. Oxidation
 c. Chemical reaction
 d. Coalescense
16.

Biscuit Gauge is another name for

 a. Hegman’s grind gauge
 b. Surface Comparator
 c. Banana Gauge
 d. Comb Gauge.
17.

Gold leaf test is used for _________

 a. Adhesion
 b. Drying
 c. Residual tack
 d. Dust detection
18.

A single pack epoxy paint dry by

 a. Coalescence
 b. Chemical curing
 c. Oxidation
 d. Solvent evaporation
19.
Pull of Adhesion is a term
associated with
 a. Tinsley pencil
 b. Banana Gauge
 c. HATE
 d. Dolly Test
20.

Which is not a property of

extender pigments?
 a. Increase Gloss
 b. Increase Adhesion
 c. Increase Cohesion
 d. Increase film strength
21.

___________ can be used to detect

the presence of oil or grease
 a. Copper sulphate
 b. Transparent Sticking Paper
 c. UV Light
 d. Brestle Sample Patch
22.

A coating fault which resembles

holidays
 a. Checking
 b. Cratering
  c. Crazing
 d. Cissing
23.

Which grade of surface

preparation required for hot duty
surfaces from above 150oC?
 a. Sa1
 b. Sa2
 c. Sa2½
 d. Sa3
24.

In Electrostatic spray, The

thickness of paint as controlled by
 a. Time used to spray
 b. Velocity of the particles
 c. Voltage
 d. Degree of dispersion
25.

Over thickness of Zinc silicate

cause
 a. Sagging
 b. Mud Cracking
 c. Curtaining
 d. Cohesive failure
26.
Which factor does not affect gloss
of a paint film?
 a. CPVC
 b. Flash Point
 c. Particle Size
 d. Solvent type
27.

According to Transco PA10,which

metal spray not required a sealer
 a. TSA
 b. Polysiloxane Inorganic Coating
 c. Poly Vinyl Buterol
 d. Inorganic Zinc Silicate
28.

It is advisable to apply Moisture

curing polyurethane by
 a. Airless spray
 b. Brushing
 c. Roller
 d. Padding
29.

IGE SR 21 is associated with

 a. Gas Plant Manufacture
 b. Handling of Methanol
 c. Abrasive Blasting Safety
 d. Using of Sand Abrasive
30.

Which paint application have

“Insulation” effect?
 a. Airless Spray
 b. Remote Pressure pot
 c. Dip coating
 d. Electrostatic spray
31.

Reflectometer measures _________

 a. Aggregate Size
 b. Agglomerates Percentage
 c. Gloss
 d. Colour
32.

A Non Destructive test can be

done
 a. When substrate contain MIO
 b. When substrate is non ferromagnetic and coating is Ferro
magnetic
 c. When substrate is Ferro magnetic and coating is Ferro
magnetic
 d. When substrate is ferromagnetic and coating is non
Ferro magnetic
33.

Which one is not included in non

ferrous substrate?
  a. Stainless steel
 b. Mild steel
 c. New Galvanising
 d. Weathered Galvanising
34.

Which one is not a compound in

millscale?
 a. FeO
 b. Fe2O3
 c. Fe2 O4
 d. Fe3O4
35.

What is the approximate overlap

area in painting?
 a. 100 mm
 b. 100 cm
 c. 10 mm
 d. 100 um
36.

In colour attributes, Brightness

also referred by the term
 a. Chroma
 b. Intensity
 c. Value
 d. Weight
37.
What is the minimum time for over
coating?
 a. 30 Minutes
 b. 4 Hrs
 c. 12 Hrs
 d. 24 Hrs
38.

Colour of Millscale
 a. Dark Blue
 b. Dark Grey
 c. Black
 d. No Colour
39.

RAL number represents

 a. Batch Number
 b. Thinner Code
 c. Colour Code
 d. Solvent Code
40.

Ropiness is fault look like

 a. Roller Stiple
 b. Rivelling
 c. Brush Marks
 d. Blisters
41.
____________ Abrasive is preferred
for Wheel abrator
 a. Steel Grit
 b. Steel Shot
 c. Grit and Shot Mixed
 d. Copper Slag
42.

_____________ flow cup can be used

to check viscosity of hot paint
 a. Ford
 b. Zahn
 c. ISO
 d. DIN
43.

Miser Valve ___________________ in

dry blasting
 a. Controls the Air Pressure
 b. Controls the flow of abrasives
 c. Removes oil and water
 d. Avoids leakage
44.

Which solution is used for cathodic

disbandment test?
 a. Slightly acidic liquid
 b. Salt water
  c. Alkaline liquid
 d. Distilled water
45.

Concentration and temperature of

sulphuric acid in pickling process
 a. 5-10% , 65-70 oC
 b. 65-70% , 5-10 oC
 c. 2%, 80 oC
 d. 80%, 65-75 oC
46.

Which one is not a laminar

pigment?
 a. Graphite
 b. Aluminium flake
 c. Glass flake
 d. China Clay
47.

Phosphating process of steel

structure is termed as
 a. Pickling
 b. Passivation
 c. Cathodic protection
 d. Salt Detection
48.
Millscale test done , when Blast
grade is
 a. Sa1
 b. Sa2 and Above
 c. Sa2½ and Above
 d. Sa3
49.

Which one is not a Paint fault?

 a. Grinning through
 b. Efflorescence
 c. Cracking
 d. Bittiness
50.

What is the total thickness of

compliant epoxy based paint?
 a. 325 um
 b. 225um
 c. 265um
 d. 365um
51.

Which term is not relate with

binder?
 a. VOC
 b. Film former
 c. Vehicle
 d. Non volatile
52.

Internal coating of pipeline come

under
 a. PA7
 b. PA8
 c. PA9
 d. PA10
53.

If a comb gauge show 120-140 um

,then the actual Dft is
 a. 120 um
 b. 130um
 c. 140 um
 d. 120 / 140 um
54.

De-lamination is a fault occurs

when using
 a. Epoxy
 b. CR
 c. Micaceous Iron Oxide
 d. Poly Urethane
55.

Nuts and Bolts can be coated by

 a. Calorising
 b. Galvanising
  c. Sheradizing
 d. Anodising
56.

________________are examples for

natural resin
 a. Amber, Laq
 b. Soya Oil, Tung Oil
 c. Bitumen , Coal tar
 d. Phenolic resin, Cellulosic resin
57.

If Paint in a density cup weighs

135gm,Relative Density is ______
 a. 135
 b. 13.5gm/cc
 c. 1.35
 d. 1.35 gm/cc
58.

Which paint from below, can be

applied over Phenolics?
 a. CR
 b. Epoxy
 c. Alkyd
 d. None of these
59. Which warning symbol represents Toxic?
  a
 b
 c
 d
60.

If more pigments added in a paint,

then the surface should be
___________
 a. Gloss
 b. Matt
 c. Grinning
 d. Fast Drying
61.

____________ is an example for

aliphatic HC solvents
 a. Water
 b. Xylene
 c. Turpentine.
 d. Acetone
62.

Non drying oils can be used in

paints, for __________
  a. Fast drying
 b. Slow drying
 c. Activate Chemical reaction
 d. Flexibility
63.

Which additive used in paints to

stop settlements?
 a. Drying oils
 b. Non Drying oils
 c. Wax
 d. Anti skinning agents
64.

If an airless spray pump ratio 35;1

delivery pressure 2800.howmuch
the inlet pressure
 a. 100psi
 b. 90psi
 c. 80psi
 d. 70psi
65.

How atomization is achieved in

conventional spray?
 a. Two air channels outside the nozzle
 b. Air pressure applied before nozzle
 c. Paint forced at high pressure
 d. Hydraulic pressure
66.
Which term is used when heat
applied over 65 oC for Drying of
Paint?
 a. Metal Spray
 b. Air Drying
 c. Stoving
 d. Forced Drying
67.

The following is not an information

of Daily report sheet
 a. Dew point
 b. Relative Humidity
 c. Relative Density
 d. Air Temperature
68.

Which one is thermoplastic?

 a. Poly ethylene
 b. Poly urethane
 c. Epoxy
 d. Natural Resin
69.

Steel temperature can be

measured by
 a. Psychro meter
 b. Limpet Gauge
  c. Thermo meter
 d. Horseshoe gauge
70.

What is the solution ,if damage

occurs to a galvanizing?
 a. T Wash
 b. Zinc Rich Epoxy
 c. CR
 d. Water Borne Acrylic
71.

Which mill widely used for

producing thick paint?
 a. Ball Mill
 b. Pearl Mill
 c. Triple Roll Mill
 d. Single Roll Mill
72.

Which one is suitable for steel

work?
 a. Short oil paint
 b. Medium oil paint
 c. Long Oil paint
 d. Full Oil paint
73.
Pigment, which dissolve in a
binder called
 a. Lacquer
 b. Dye
 c. Varnish
 d. Solute
74.

If 11 Litres Paint Weighs 18 Kg

then density =
 a. 1.8 gm/cm
 b. 1.6 gm/cm
 c. 1.1 gm/cc
 d. 1.6 gm/cc
75.

Ford Flow cup made of ___________

 a. Stainless Steel
 b. Aluminium Alloy
 c. Mild Steel
 d. Glass Reinforced Plastic
76.

When temperature
increases,__________?
 a. Viscosity increases
 b. Viscosity decreases
 c. Viscosity Stable
 d. Drying time increases
77.

What is the approximate induction

period of CR?
 a. 20 minutes
 b. 30 minutes
 c. 6-8 hrs
 d. Not Applicable
78.

Stroboscope checks
 a. Rotation
 b. Polarity
 c. Potential
 d. Aggregate count
79.

Which paint mill produce

expensive materials?
 a. Triple roll mill
 b. Single roll mill
 c. Sand mill
 d. Ball mill
80.

High speed stone mill is another

name for
 a. High speed disperser
 b. Pearl mill
  c. Colloid mill
 d. Attritor Mill
81.

Which paint is not suitable for

EPA?
 a. Water borne
 b. High volume solid
 c. Solvent Based
 d. Solvent free
82.

By which polymerisation method a

2 pack epoxy paint dry?
 a. Cross linked Polymer
 b. Branched Polymer
 c. Solution Polymer
 d. Linear Polymer
83.

Transco Specification PA9

Specifies
 a. New and Maintenance painting at work and site for AGI
 b. Paint Properties and Performance
 c. Internal coating of steel small bore pipe
 d. Preparation of steel substrate before application of
paint
84.
Which term cannot be used for
solid particles in binder?
 a. Aggregates
 b. Emulsion
 c. Degree of dispersion
 d. Fineness of grind
85.

Which one is more suitable for CR

paint to increase flexibility?
 a. Alkyd resin
 b. Linceed oil
 c. Bentones
 d. Coconut oil
86.

__________ is not a unit of viscosity

 a. Stoke
 b. Poise
 c. Littre
 d. Second
87.

Which type of Comb gauge is not

available?
 a. Square
 b. Circle
 c. Triangular
 d. Rectangular
88.

Which application method used to

apply paints on damp surface?
 a. Brush
 b. Roller
 c. Airless Spray
 d. Dip coating
89.

What is BS 4800 specifies?

 a. Colour co-ordination
 b. Specification of abrasive size sieves
 c. Methods of test for paints
 d. Glossary of paint and related terms
90.

Which application greatly reduce

pinholes?
 a. Brush
 b. Spray
 c. Aerosol
 d. Roller
91.

Spray tip with adjustable aperture

size known as
 a. Carbide
 b. Venturi
  c. Titan
 d. Taber
92.

Pyro meter is an instrument to

check
 a. Adhesion
 b. Hardness
 c. Steel Temp
 d. Density
93.

Graticule scale is a part of

 a. PIG
 b. Hegman Grind Gauge
 c. Eccentric Wheel
 d. Tough type Pfund Crypto meter
94.

MDS shows a two pack paint

density is 1.35 gm/cc, when the
density check completed it shows
the density as 1.25.Which one is
true
 a. Base Part is High
 b. Activator Part is High
 c. Mix ratio on MDS is incorrect
 d. Activator Part is Low
95.
In which temperature
Density,Viscosity etc tests of
Paints done?
 a. 20 ºC ± 0.5 ºC
 b. 37 ºC ± 0.5 ºC
 c. 100 ºC ± 0.5 ºC
 d. Temperature not affected
96.

If metal spray applied on a thin

steel plate ,
 a. Plate should not be heated
 b. Plate should be preheated
 c. Plate should be post heated
 d. Cannot be applied
97.

BS 7079 does not contains

 a. Rust Grades
 b. Blast Grades
 c. Hand and Power tool Grades
 d. Salt tests on Substrate
98.

Wa1 ,Wa2 are grades of

 a. Abrasive blasting
 b. Closed blasting
 c. Water Blasting
 d. Weathering Grades
99.

When using replica tape 50um

deducted because _________?
 a. Thickness of paper
 b. Thickness of transparent layer
 c. Thickness of Testex
 d. Dial micrometer Criteria
100.

Which blasting is suitable for non-

ferrous substrates?
 a. Thorough abrasive blasting
 b. Sweep blasting
 c. Sa2½
 d. Not Applicable