Doc. Ref.

: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 2 of 42

TABULATION OF REVISED PAGES

REVISIONS REVISIONS
SHEET SHEET
00 01 02 03 00
1 X 51
2 X 52
3 X 53
4 X X X 54
5 X 55
6 X 56
7 X 57
8 X 58
9 X 59
10 X 60
11 X X 61
12 X 62
13 X 63
14 X 64
15 X 65
16 X X 66
17 X X 67
18 X X X 68
19 X 69
20 X 70
21 X X X 71
22 X X 72
23 X X 73
24 X X 74
25 X X 75
26 X X 76
27 X X 77
28 X X 78
29 X X 79
30 X X 80
31 X X 81
32 X X 82
33 X 83
34 X 84
35 X 85
36 X 86
37 X 87
38 X 88
39 X 89
40 X 90
41 X X 91
42 92
43 93
44 94
45 95
46 96
47 97
48 98
49 99
50 100

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 3 of 42

7$%/(2)&217(176
1 Scope ...................................................................................................................................................... 4
2 Responsibilities ..................................................................................................................................... 4
3 Reference Documents ........................................................................................................................... 4
3.1 Standards ............................................................................................................................................. 4
3.2 Professional Documents ....................................................................................................................... 5
3.3 Regulations ........................................................................................................................................... 6
3.4 Codes ................................................................................................................................................... 6
3.5 Total General Specifications ................................................................................................................. 6
4 Class numbering principles .................................................................................................................. 7
4.1 Generation of number ........................................................................................................................... 7
4.2 Letters representing the flanges rating of the class.............................................................................. 7
4.3 Numbers representing the main material of the class .......................................................................... 7
4.4 Suffixes ................................................................................................................................................. 7
5 Abbreviations used (in alphabetical order) ......................................................................................... 8
6 General notes ......................................................................................................................................... 9
6.1 Units ...................................................................................................................................................... 9
6.2 Design limits and pipe wall thickness ................................................................................................... 9
6.2.1 Design limits ......................................................................................................................................... 9
6.2.2 Pipe wall thickness calculation principle ............................................................................................... 9
6.2.2.1 Corrosion allowance ............................................................................................................................. 9
6.2.2.2 Mill tolerance ......................................................................................................................................... 9
6.2.2.3 Retirement thickness .......................................................................................................................... 10
6.2.2.4 Sample of Wall thickness calculation ................................................................................................. 11
6.3 Pipe diameters .................................................................................................................................... 12
6.4 Threaded joints ................................................................................................................................... 12
6.4.1 Threads standards .............................................................................................................................. 12
6.4.2 Threaded connections limitations ....................................................................................................... 12
6.5 Joining of small bore pipes ................................................................................................................. 12
6.6 Bends and elbows in small bore piping .............................................................................................. 12
6.7 Unions ................................................................................................................................................. 12
6.8 Bolt tensioners .................................................................................................................................... 13
6.9 Valves ................................................................................................................................................. 13
6.9.1 Ball Valves .......................................................................................................................................... 13
6.9.2 Gate, globe, butterfly and check valves.............................................................................................. 13
6.9.3 Block and bleed valves ....................................................................................................................... 13
6.10 Pipes ................................................................................................................................................... 14
6.11 Fittings ................................................................................................................................................ 14
6.12 Flanges, blinds and spacers ............................................................................................................... 14
6.13 Bolting ................................................................................................................................................. 14
6.14 Gaskets ............................................................................................................................................... 14
6.15 Slip-on flanges .................................................................................................................................... 14
6.16 Miter bends ......................................................................................................................................... 14
6.17 Glass Reinforced Plastic materials (GRP).......................................................................................... 14
6.18 Branch Connection ............................................................................................................................. 15
6.19 Spectacle blinds.................................................................................................................................. 15
7 List of Classes ...................................................................................................................................... 16
8 Annexes ................................................................................................................................................ 19
8.1 Piping Classes .................................................................................................................................... 19
8.2 Branch Reinforcement Table .............................................................................................................. 19

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 4 of 42

1 Scope
This specification covers the technical requirements of materials for pipes, fittings, flanges, valves and
other piping components for use on process and utility piping systems for EPSC1 and EPSC 2 phase of
New FP2 platform and QP2 platform in the frame of YADANA –Subsidence Project.
All piping material classes specified on the Piping Layouts and P&ID of the YADANA Subsidence
Project shall refer to this specification.
This document does not apply to:
• Fabricated ducts
• Heating, plumbing, ventilation, HVAC piping, chilled waters system and similar piping inside buildings
• Instrumentation tubing
• Portions of steam, boilers water and exhaust piping covered by the ASME Code, Section 1

2 Responsibilities
Any conflict between the requirements of this specification and reference documents shall be referred to
COMPANY for clarification.

3 Reference Documents
The reference documents listed below form an integral part of this General Specification. Unless
otherwise stipulated, the applicable version of these documents, including relevant appendices and
supplements, is the latest revision published at the EFFECTIVE DATE of the CONTRACT.
This specification is based on the latest issue of the code ASME B31.3, incorporating all published
addenda for all classes, with the exception of refrigerated piping for which the code ASME B31.5 is used
(such classes are identified with a suffix letter “R”).

3.1 Standards
Reference Title
ASME B1.1 Unified Inch Screw Threads
ASME B1.2 Gages and Gaging for Unified Inch Screw Threads
ASME B1.20.1 Pipe Threads, general purpose (inch)
ASME B2.1 Pipe Threads (Except Dry seal)
Pipe Flanges and Flanged Fittings NPS 1/2 Through NPS 24 Metric/Inch
ASME B16.5
Standard
ASME B16.9 Factory-Made Wrought Buttwelding Fittings
ASME B16.10 Face to Face and End to End Dimensions of Valves
ASME B16.11 Forged Fittings, Socket-Welding and Threaded
ASME B16.20 Metallic Gaskets for Pipe Flanges Ring-Joint, Spiral-Wound, and Jacketed
ASME B16.21 Non-metallic Flat Gaskets for Pipe Flanges
Cast Copper Alloy Pipe Flanges and Flanged Fittings Classes 150, 300, 600,
ASME B16.24
900, 1500, and 2500
ASME B16.25 Butt Welding Ends
ASME B16.34 Valves-Flanged, Threaded, and Welding End
ASME B16.36 Steel Orifice Flanges

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 5 of 42

Reference Title
ASME B16.47 Large Diameter Steel Flanges NPS 26 Through NPS 60 Metric/Inch Standard
ASME B16.48 Line Blanks
Square, Hex, Heavy Hex, and Askew Head Bolts and Hex, Heavy Hex, Hex
ASME B18.2.1
Flange, Lobed Head, and Lag Screws (Inch Series)
Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange,
ASME B18.2.2
and Coupling Nuts (Inch Series)
ASME B36.10M Welded and Seamless Wrought Steel Pipe
ASME B36.19M Stainless Steel Pipe
ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)
Standard Finishes for Contact Faces of Pipe Flanges and Connecting-Ends
MSS SP 6
Flanges of Valves and Fittings
MSS SP 9 Spot Facing for Bronze, Iron and Steel Flanges
MSS SP 25 Standard Marking System for Valves, Fittings, Flanges and Unions
Corrosion Resistant Gate, Globe, Angle and Check Valves with Flanged and
MSS SP 42
Butt weld Ends
MSS SP 43 Wrought Stainless Steel Butt-Welding Fittings
MSS SP 45 By-pass and Drain Connection Standard
MSS SP 61 Pressure testing of Steel Valves
MSS SP 70 Cast Iron Gate Valves, Flanged and Threaded Ends
MSS SP 72 Ball Valves with Flanged or Butt-Welding Ends for General Service
MSS SP 75 High Test Wrought Welding Fittings
MSS SP 80 Bronze Gate, Globe, Angle and Check Valves
MSS SP 95 Swaged Nipple and Bull Pugs
Integrally reinforced forged branch outlet fittings - Socket welding, threaded
MSS SP 97
and butt welding end
ISO 10497 Testing of valves - Fire type-testing requirements
UKOOA/ ISO14692 Petroleum and natural gas industries - Glass-reinforced plastics

3.2 Professional Documents

Reference Title
API SPEC 5L Specification for Line Pipe
API SPEC 6D Pipeline valves
API SPEC 6FA Specification for Fire test for Valves
API STD 594 Check Valves : Flanged, Lug, Wafer and Butt-welding
API STD 598 Valves Inspection and Testing
API STD 600 Steel Gate Valves Flanged and Butt-welding Ends, Bolted Bonnets
API STD 602 Compact Steel Gate Valves
API STD 605 Large Diameter Carbon Steel Flanges
API STD 607 Fire Test for Quarter-turn Valves and Valves Equipped with Nonmetallic Seat
API STD 609 Butterfly Valves Double Flanged, Lug-type and Water-type

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 6 of 42

3.3 Regulations
Myanmar local regulation is fully applicable and takes precedence to any other codes and specifications.

3.4 Codes

Reference Title
ASME B31.3 Process Piping

3.5 Total General Specifications

Reference Title
GS EP COR 350 External protection of offshore and costal structures and equipment painting
GS EP COR 356 Corrosion Protection of Fasteners for Subsea and Topside applications
GS EP PVV 101 List of piping documents to be supplied to COMPANY
GS EP PVV 107 Piping Stress Analysis
GS EP PVV 111 Piping design specification
GS EP PVV 112 Piping Material Classes
GS EP PVV 113 Block models
GS EP PVV 114 Design models
GS EP PVV 115 3D electronic models
GS EP PVV 116 Model review check list
Design and fabrication of metallic piping supports - Standard for piping
GS EP PVV 119
supports
GS EP PVV 142 Valves
GS EP PVV 143 Metallic pipes
GS EP PVV 144 Fittings
GS EP PVV 145 Flanges
GS EP PVV 146 Bolting for piping
GS EP PVV 147 Gaskets for piping and vessels
GS EP PVV 148 Glass - Reinforced plastic. Piping materials (tubes and accessories)
GS EP PVV 149 Spring hangers and supports
GS EP PVV 171 Steel piping fabrication
GS EP PVV 178 Design and erection of Glass Reinforced Plastic (GRP) piping system
GS EP PVV 611 Welding of pressure containing piping and equipment

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 7 of 42

4 Class numbering principles

4.1 Generation of number

The class number shall consist of a capital letter representing the ASME or API flanges rating, and a
two-digit number representing the main material entering into the composition of the material used for
the pipes, fittings, flanges, valves, etc., of the piping material class in question.
Example: B01N

Rating 150 Carbon Steel material Suffix, Optional

The letters and numbers to be used for numbering piping classes are indicated hereafter

4.2 Letters representing the flanges rating of the class

Rating 150 300 600 900 1500 2500 5000 10000

Letter B D F G H J K L

4.3 Numbers representing the main material of the class

01 to 30: Carbon steels (digits "X"1 to "X"6 also indicate the corrosion allowance for carbon steels,
namely 1.27 to 6 mm)
(Digits “X2” indicate steam services fluids)
31 to 44: Alloy steels
(Digits “X2” indicate steam services fluids)
45 to 70: Stainless steels
71 to 85: Special alloys (Monel, Hastelloy, etc.)
86 to 99: Other materials (Cast-iron, copper alloy, GRE, etc.).

4.4 Suffixes
Not Applicable

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 8 of 42

5 Abbreviations used (in alphabetical order)

ASME American Society of Mechanical Engineers MI Malleable cast Iron

API American Petroleum Institute Mo Molybdenum
ASTM American Society for Testing and Materials MSS Manufacturers Standardization Society
BB Bolted Bonnet NPT Threading as per ASME B1.20.1
BC Bolted Cover OS&Y Outside Screw spindle and Yoke
BE Beveled End PE Plain End
Br Bronze PTFE Teflon
BW Butt Welding PVDF Polyvinylidiene Fluoride
CAS Cast Alloy Steel RF Raised Face
CCS Cast Carbon Steel RJ Machined face for ring Joint
CS Carbon Steel SAW Submerged Arc Welded
Cu-Ni Copper-Nickel SB Screwed Bonnet
Cr Chromium SF Small Female face
EFW Electric Fusion Welded SM Small Male face
ENP Electro-less Nickel Plated SMLS Seamless
ERW Electric Resistance Welded SO Slip-On
ES Extended Spindle SP Standard Practice (MSS)
FAS Forged Alloy Steel SPB Split Body
FCS Forged Carbon Steel SS Stainless Steel
FF Flat Face STD Standard
F6 Stainless steel, 13% Cr SW Socket Welding
Gr Grade TE Threaded End
GRP Glass Reinforced Plastic TM Trunnion Mounted
HCP Hard Chrome Plated TPE Top Entry
Hh Heavy Hexagonal WN Welding Neck
ISRS Inside Screw Riser Spindle WB Welded Bonnet
LJ Lap Joint WC Welded Cover
LTCS Low Temperature Carbon Steel

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 9 of 42

6 General notes
6.1 Units
All units are expressed in the international SI system, except for nominal bore sizes of pipes, which are in
inches. Pressures are gauge pressures (in barg), unless otherwise stated. Unless otherwise stated,
Temperatures are in degrees Celsius.
Pressure/Temperature ratings of flanges are based on the latest version of the ASME B16.5 & ASME
B16.47.

6.2 Design limits and pipe wall thickness

6.2.1 Design limits
Pipe wall thickness values that are specified in the Piping Material Specifications are adequate for the full
range of pressure/temperature combinations tabulated.

6.2.2 Pipe wall thickness calculation principle

The calculation of pipe wall thickness values shall be in accordance with the ASME B31.3 design code,
and shall include a corrosion allowance as well as mill tolerances as applicable. The weld efficiency
coefficient of welded pipes shall be equal to 1.0 (i.e. full radiography). Threaded allowance as applicable
by design code to be added as per class specification.

6.2.2.1 Corrosion allowance

All carbon steel and low alloy steel materials shall incorporate a minimum corrosion allowance of 1.27
mm. Stainless steels, copper nickels, glass reinforced materials, and other corrosion resistant
materials shall be used without extra-thickness for corrosion allowance.

6.2.2.2 Mill tolerance

The mill tolerance on wall thickness shall be as follows:
• Minus 8% for diameters 18" and above
• Minus 12 ½% for diameters up to 16".

(These rules take into account the fabrication tolerances applicable to fittings, with a particular
reference to GS EP PVV 144).
Mill tolerance for other material which not specified in document shall be complying with applicable
ASTM standard.

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 10 of 42

6.2.2.3 Retirement thickness

The minimum wall thickness after reduction by:
• Corrosion Allowance
• Mill Tolerance
• Threading Allowance, where applicable, in accordance with ASME B1.20.1 shall not be less
than the following:

Nominal Pipe Size Minimum corroded thickness

(NPS) (retirement thickness)
½" to ¾" 1.0 mm
1" to 8" 1.5 mm
10" 2.3 mm
12" to 14" 2.8 mm
16" to 24" 3.1 mm
26" to 36" 3.8 mm
38" to 46" 4.6 mm
48" 5.3 mm
Above 48" 6.4 mm

Additionally, schedules "5 S" shall not be used for stainless steels, and schedule 80 shall be selected
as a minimum for pipes 1”½ in diameter and below.
If the wall thickness required to contain the pressure is less than the "Minimum Corroded Thickness",
the "Minimum Corroded Thickness" shall be used for pipe wall thickness selection purpose.

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 11 of 42

6.2.2.4 Sample of Wall thickness calculation

Doc.Ref : MM-YAD-00-GU01-504002
CTR Reference: NA
CALCULATION FOR PIPE WALL THICKNESS Revision : 01 Rev. Date : 15-Jun-2012
Discipline : PVV Document Type : SPE
Doc type : CAL Syst/S-Syst : N/A Discipline : PVV Class : 1 Page 9 of 38

7.1 PIPING CLASS B01

3LSLQJ6SHF&RGH % 'HVLJQ&RGH $60(%

$60(&ODVV  
3LSH0DWHULDO6WDQGDUG $3,/*U% (  0DWHULDO7\SH &6)HUULWLF6WHHO
: 
'HVLJQ3UHVVXUH3  EDU J  03D

'HVLJQ7HPSHUDWXUH  & 5HI'HVLJQ&RGH $60(%(G (TQ D

6#  &  03D
F  PP 0LOO7ROHUDQFH   XSWR

<#  &    DQGDERYH

W  3[' >[^ 6[([:  3[< `@ ZKHUH

9DOLGIRUW' Temp P S
' 2XWVLGH'LDPHWHURI3LSHPP 36 ( 0C ) bar (g) (MPa)
3 ,QWHUQDO'HVLJQ*DJH3UHVVXUH03D    
W 3UHVVXUH'HVLJQ7KLFNQHVVDVFDOFXODWHGLQDFFRUGDQFHZLWKSDUDIRULQWHUQDOSUHVVXUHPP    
WP 0LQLPXP5HTXLUHG7KLFNQHVVLQFOXGLQJ0HFKDQLFDO&RUURVLRQ (URVLRQ$OORZDQFHVPP    
WP WF  0LOO7ROHUDQFH    
6 6WUHVV9DOXHIRU0DWHULDOIURP7DEOH$03D 
( 4XDOLW\)DFWRUIURP7DEOH$$RU$%
: :HOGMRLQWVWUHQJWKUHGXFWLRQIDFWRUDVSHU7DEOH
< &RHIILFLHQWIURP7DEOHYDOLGIRUW'
F 6XPRI0HFKDQLFDO$OORZDQFHV 7KUHDGRU*URRYH'HSWKZKHUHYHUDSSOLFDEOH SOXV&RUURVLRQ (URVLRQ$OORZDQFHVPP
6FK 6FKHGXOHVHOHFWHGDVQH[WKLJKHUDVRIWPDVSHUWKHGLPHQVLRQDOVWDQGDUG 5HI$60(%0RU$60(%0
6FK 6FKHGXOHVSHFLILHGDVSHU6SHF3LSLQJ0DWHULDO&ODVVHV 5HI,'632$//
6FK 6HOHFWHGVFKHGXOHIRUWKHSLSHGLDPHWHU
75  UHWLUHPHQWWKLFNQHVVDVSHU*6399SDUD
730&  0D[LPXPYDOXHEHWZHHQFDOFXODWHGWKLFNQHVV W DQGUHWLUHPHQWWKLFNQHVV 75 

Pipe NB Pipe OD t TR T PMC tm Thk of Sch Ratio

Sch1 Sch2 Sch Validation
NPS ( in ) (mm) (mm) (mm) (mm) (mm) (mm) D/t >6
0.5 0.840 21.3 0.1508 1.00 1.000 2.5943 STD 80 80 3.73 141.51 Valid
0.75 1.050 26.7 0.1885 1.00 1.000 2.5943 STD 80 80 3.91 141.51 Valid
1 1.315 33.4 0.2360 1.50 1.500 3.1657 STD 80 80 4.55 141.51 Valid
1.5 1.900 48.3 0.3410 1.50 1.500 3.1657 30 80 80 5.08 141.51 Valid
2 2.375 60.3 0.4263 1.50 1.500 3.1657 30 80 80 5.54 141.51 Valid
3 3.500 88.9 0.6282 1.50 1.500 3.1657 30 40 40 5.49 141.51 Valid
4 4.500 114.3 0.8077 1.50 1.500 3.1657 30 40 40 6.02 141.51 Valid
6 6.625 168.3 1.1891 1.50 1.500 3.1657 10 40 40 7.11 141.51 Valid
8 8.625 219.1 1.5481 1.50 1.548 3.2207 10 20 20 6.35 141.51 Valid
10 10.750 273.1 1.9296 2.30 2.300 4.0800 10 20 20 6.35 141.51 Valid
12 12.750 323.9 2.2885 2.80 2.800 4.6514 20 20 20 6.35 141.51 Valid
14 14.000 355.6 2.5129 2.80 2.800 4.6514 10 10 10 6.35 141.51 Valid
16 16.000 406.4 2.8719 3.10 3.100 4.9943 10 10 10 6.35 141.51 Valid
18 18.000 457.2 3.2309 3.10 3.231 4.8923 10 10 10 6.35 141.51 Valid
20 20.000 508.0 3.5899 3.10 3.590 5.2825 10 10 10 6.35 141.51 Valid
24 24.000 609.6 4.3078 3.10 4.308 6.0629 10 20 20 9.53 141.51 Valid
26 26.000 660.4 4.6668 3.80 4.667 6.4531 10 10 10 7.92 141.51 Valid
28 28.000 711.2 5.0258 3.80 5.026 6.8433 10 10 10 7.92 141.51 Valid
30 30.000 762.0 5.3848 3.80 5.385 7.2335 10 10 10 7.92 141.51 Valid
32 32.000 812.8 5.7438 3.80 5.744 7.6237 10 10 10 7.92 141.51 Valid
34 34.000 863.6 6.1028 3.80 6.103 8.0139 STD STD STD 9.53 141.51 Valid
36 36.000 914.4 6.4618 3.80 6.462 8.4041 STD STD STD 9.53 141.51 Valid

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 12 of 42

6.3 Pipe diameters

No pipe diameter smaller than ½" shall be used, except for instruments.
Pipe diameters of 1”¼, 2”½, 3”½, 5", 7", 9" and 22" shall not be used. Equipment supplied with
connections of these sizes shall be adjusted to a standard size immediately adjacent to the equipment by
means of a suitable reducing fitting. Bushings shall not be used. For diameters above 24", sizes of 30",
36", 42", 48", 56" and 60" are preferred dimensions.

6.4 Threaded joints

6.4.1 Threads standards

All threaded connections shall have taper threads in accordance with ASME B1.20.1 (NPT) (formerly
ASME B2.1).

6.4.2 Threaded connections limitations

Threaded joints are only authorized on utility lines if and where listed on the relevant piping material
class.
Threaded joints shall not be used on process service, with the exception of instrument connections which
are located downstream a block valve; in such a case, the upstream side of this block valve shall be
flanged or may be socket welded on a nipple with a flanged joint immediately upstream to ensure further
possible maintenance.
Threaded connections are absolutely not authorized in the following cases (related to particular fluids or
services):
• Hazardous service, e.g.:
- Liquids above their Auto-Ignition Temperature (AIT), or at temperatures greater than 210°C, if the
AIT is not known
- Flammable liquids flashing on leakage to form a substantial vapor cloud (this includes LNG
condensate)
- Fluids liable to cause a hazard by blockage due to hydrate formation or solids deposits
- Lethal or toxic substances, including H2S gas
- High pressure air injection (ratings • 900)
• General chemical service
• Highly corrosive fluids (e.g., acids such as hydrochloric or Fluor hydric acids).

6.5 Joining of small bore pipes

With the exception of galvanized systems which shall be joined together only by threaded connections,
small bore piping (1”½ and smaller) shall be joined together by socket welding.
Threaded connections may only be used where permitted under paragraph 6.4.2 of this specification,
and butt welding joints shall not be used.

6.6 Bends and elbows in small bore piping

In small bore welded piping (1”½ and smaller), hot or cold-formed bends with a radius of 5D min. may be
used in lieu of elbows if and where authorized in the relevant piping material class.

6.7 Unions
Unions may only be used where threaded connections are authorized by this specification; in general,
their use shall be avoided wherever possible. They shall not be used in the following circumstances:

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 13 of 42

• Systems ratings 600 and above

• Where design temperature is above 250°C
• Cryogenic Temperature Service (Design temperatures < minus 46°C).
• Corrosive and Toxic Service (including H2S gas)
• Fuel Gas Service.

6.8 Bolt tensioners

Hydraulic bolt tensioners shall be used on flange stud bolts 50 mm in diameter and larger. Bolting for use
with bolt tensioners shall have the normal length increased by one bolt diameter.

6.9 Valves
All valves shall comply with the requirements of GS EP PVV 142.

6.9.1 Ball Valves

All Ball Valves are meant to be reduced bore, except otherwise indicated on the PID for each individual
Ball Valve. Valves of diameter ” 1”½ shall have a port size at least equal to the internal bore of the
matching pipe.

When Ball Valves are installed in lines that are insulated for any purpose, they shall be provided with
extended spindle assembly suitable for making an insulation seal. Extended spindles shall be:
• For Valves diameter 2 inches and smaller: 100 mm, plus or minus 10 mm
• For Valves diameter 3 inches and larger: 150 mm, plus or minus 10 mm.
For flanged valves, the extended spindle length is measured from the top of an end flange; for screwed
or socket weld valves, it is measured from the top of the valve body.

6.9.2 Gate, globe, butterfly and check valves

Forged materials are acceptable in lieu of cast materials.
Dual plate check valves are acceptable in lieu of swing check valves. Wafer-Lug type check valves are
acceptable in lieu of flanged check valves.

6.9.3 Block and bleed valves

Use of integral block and bleed valves shall be limited to instrument connections.
Instrument connections on either piping or pressure vessels requiring either single or double block or
bleed facilities shall be made of an integrated manifold.
Manifold shall be ball type two or three pieces bolted.
For integral manifold less than 2”, the internal diameter of the main body shall be 10 mm minimum.
The bleed valve shall be needle type with a bolted bonnet.
The side of this integrated manifold, which connects to the piping, or the pressure vessel must be
flanged, whilst the instrument connection side may be flanged or ½” NPT female depending on
instrument connection:
The bleed connection shall be ½” NPTF protected by a metallic plug screwed (as per GS EP PVV 142).
All integrated (or Monoblock) manifolds shall be in line type; the Monoflange type is prohibited.

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 14 of 42

6.10 Pipes
All metallic pipes shall comply with the requirements of GS EP PVV 143.

6.11 Fittings
All metallic pipe fittings shall comply with the requirements of GS EP PVV 144.

6.12 Flanges, blinds and spacers

All metallic pipe flanges, blinds and spacers shall comply with the requirements of GS EP PVV 145.

6.13 Bolting
All bolting for piping shall comply with the requirements of GS EP PVV 146.

6.14 Gaskets
All gaskets for piping shall comply with the requirements of GS EP PVV 147.

6.15 Slip-on flanges

The use of slip-on flanges is not generally permitted. They may be used, however, where necessary, for
tie-ins, subject to the following restrictions:
• Maximum pressure/temperature rating of class 300
• Maximum design temperature of 260°C
• Carbon steel materials only
• Their use is not permitted in sour, corrosive or severe cyclic services.

6.16 Miter bends

Butt weld elbows shall normally be used. Miter bends shall not be used except where specifically agreed
by the Company. In case such an agreement is given, a re-run of the flexibility analysis of the
corresponding line is necessary. No agreement may be granted on lines requiring more than 5%
radiographic examination, or being stress relieved, or being subject to sour, corrosive or severe cyclic
services.

6.17 Glass Reinforced Plastic materials (GRP)

GRP materials shall comply with GS EP PVV 148.

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 15 of 42

6.18 Branch Connection

The principle is as follows:
• Connections of equal sizes always require an equal Tee.
• Connections where both header and branch are of a diameter less than 2 inches are made using
Tees (equal or reduced).
• Reducing or equal Tees to be used if the branch diameter is equal to half the header diameter or
larger.
• All other connections shall be made using branch outlet fittings such as weldolets, sockolets,
sweepolets etc., for branch diameters less than half the header diameter only. The use of weldolets
shall be limited to 8” branch diameter maximum to avoid the risk of welding thermal distortion.
Sweepolet or reducing tee plus reducer are to be used instead.
• Special cases may require different rules or means for reinforcing branch connections (including the
use of extruded headers, etc.). These must be submitted to the Company for decision.
• Except for branch connections made of equal or reduced tees, the use of integral reinforced
connections in one single piece (comprising the required reinforcement, a nipple -“nippolet”-, and
eventually an end-flange - “weldoflange”) is permitted.

6.19 Spectacle blinds

Spectacle blinds dimensions (thickness) and materials shall be fully justified by the Engineering
Company by appropriate calculations in accordance with the applicable ASME code (i.e., ASME B31.3).
Detailed calculations shall be submitted to the COMPANY for approval.

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 16 of 42

7 List of Classes

Design
Rating Face
Conditions
Material corrosion
Class allowance Symbol Service
Gaskets P T
(mm)
Bolting (bar) ( °C )

150 RF 19.6 -29/+37

DO Diesel Oil
Non CAF Flat Carbon Steel
B01 17.7 +100 AV Atmospheric Vent (Noncorrosive)
Gaskets
CA = 1.27mm
FG Fuel Gas
B7 / 2H 13.12 +220

150 RF 19.6 -29/+37

Non CAF Flat Carbon Steel

B03 17.7 +100 FA Low Pressure Flare
Gaskets CA = 3 mm

B7 / 2H 13.8 +200

150 RF 19.6 -29/+37

OD Open Drain (Medium Corrosive)
B05 Non CAF Flat Carbon Steel
17.7 +100 CD Closed Drain (Medium Corrosive)
Gaskets CA = 5 mm
PW Process Water (Oily Water)
B7 / 2H 13.8 +200

150 RF 19.6 -29/+37

CS (1.27)
Non CAF Flat IA Instrument Air
B10 Galvanized 17.7 +100
Gaskets SA Service Air
CA = 1.27 mm
B7 / 2H 13.8 +200

150 RF 19.6 -29/+37

Non CAF Flat CS (3) Galvanized

B13 17.7 +100 UW Utility Water (Noncorrosive)
Gaskets CA = 3 mm

B7 / 2H 13.8 +200

150 RF 19.6 -46/+37

Low temperature
Non CAF Flat Carbon Steel
B23 (LCTS) 17.7 +100 FB High Pressure Flare
Gaskets
CA = 3 mm
B7M / 2HM 13.8 +200

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 17 of 42

Design
Rating Face
Conditions
Material corrosion
Class allowance Symbol Service
Gaskets P T
(mm)
Bolting (bar) ( °C )

150 RF 19 -46/+37 Process Water

IA Instrument Air
Non CAF Flat SS TP 321
B48 17 +100 SA Service Air
Gaskets CA = 0 mm
JF Jet Fuel
B8M / 8MA 13.8 +200 Fuel Gas

150 RF 15.9 -46/+37

SS 904L/316L(min
Non CAF Flat Mo Content 2.5%)
B50 13.3 +100 CK Corrosion Inhibitor
Gaskets
CA = 0 mm
B8M/8MA 11.2 +200

150 FF
Atmospheric Vent (Corrosive)
GRP AV
Neoprene Flat Fire-fighting Water –Wet System
B90 Copper – Nickel 18 -29/90 FW
Gaskets (Corrosive)
CA = 0 mm SW
Sea Water
B7 / 2H

150 FF
CI Chlorine injection
Neoprene Flat GRP
B91 12 -29/90 OD Open Drain (Corrosive)
Gaskets CA = 0 mm
WS Sewage Water
B7 / 2H

150 FF 19.6 -29/+37

Neoprene Flat Copper-Nickel Fire-fighting Water –Dry system

B92 18.8 +65 FW
Gaskets CA = 0 mm (Corrosive)

B7 / 2H 18.0 +90

150 FF 18.0 -29/+37

GRP
B93 Neoprene Flat SS TP 321 CD Closed Drain (Corrosive)
17.6 +65
Gaskets
CA = 0 mm
B8M/8MA 16.6 +90

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 18 of 42

Design
Rating Face
Conditions
Material corrosion
Class allowance Symbol Service
Gaskets P T
(mm)
Bolting (bar) ( °C )

150 FF -29/+37
GRP
Neoprene Flat DW Potable Water/Drinking Water
B95 Copper – Nickel 18 +65
Gaskets UW Utility Water (corrosive)
CA = 0 mm
B7 / 2H +90

D05 300 RF 51.1 -29/+37

Non CAF Flat Carbon Steel

46.6 +100 CD Closed Drain (Medium Corrosive)
Gaskets CA = 5 mm

B7 / 2H 43.8 +200

600 RF 102.1 -29/+37

Carbon Steel
F03 Spiral wound 93.2 +100 HC Corrosive Hydrocarbon
CA = 3 mm
B7 / 2H 87.6 +200

600 RF 99.3 -46/+37

SS TP 321
F48 Spiral wound 88.5 +100 HC Hydrocarbon
CA = 0 mm

B8M / 8MA 76.6 +200

900 RF 148.9 -46/+37

CD Closed Drain (Corrosive)
SS TP 321
G48 Ring Joint 132.7 +100 PW Process Water (Oily Water)
CA = 0 mm
HO Hydraulic Oil
B8M / 8MA 114.9 +200

1500 RF 248.2 -46/+37

SS TP 321
H48 Ring Joint 221.2 +100 HC Hydrocarbon
CA = 0 mm
B8M / 8MA 191.5 +200

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 19 of 42

1500 RF 206.8 -46/+37

SS 904L/316L(min
H50 Ring Joint Mo Content 2.5%) 173.9 +100 CK Corrosion Inhibitor
CA = 0 mm
B8M/8MA 145.8 +200

8 Annexes
8.1 Piping Classes
8.2 Branch Reinforcement Table

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 03 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 20 of 42

Annex 1- Piping Classes

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO&DUERQVWHHO 5DWLQJ /EV5)
B 01
Exploration & Production
6HUYLFH +\GURFDUERQV JDVRUOLTXLGV  QRQFRUURVLYH 1RQFRUURVLYHIXHO &RUURVLRQ Date: 
1.27 mm
JDV)XHO2LO'LHVHORLO DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                  
3LSHV 

/DUJHUVL]HVDFFRUGLQJWR
6FKHGXOH       WDEOHEHORZ
(QGV 3( %(
0DW6SHF  $3,/*U%VHDPOHVV $3,/*U%6$:UDGLRJUDSK\
/EV6:$ž
$670$:3%DVSHUSLSHVFKHGXOH%:žRUžHOERZV U GLD 
)LWWWLQJV RUžHOERZV  
FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV
FRXSOLQJVWHHVVRFNROHWV
/EV5)6:$ $:1/EV5)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 
)ODQJHV
 :1/EV5)RULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQW
FRQQHFWLRQ
/EV6:$
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUDQGDERYH
*DWHYDOYHV 6WHOOLWHFRDWHG
26 <%%*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
26 <%% 
/EV6:$ $670$RU$:&%%RG\$(13EDOO6HDOV  63%RU73(
%DOOYDOYHV
7ULP6HDOV )ORDWLQJEDOOIRUGLDPHWHUXSWRDQG7UXQQLRQPRXQWHGIRUGLDPHWHUDQGDERYH

)ORDWLQJEDOO  *HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG 
/EV6:$ $:&%%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%%  
/EV6:$
3OXJYDOYHV $:&%6HDOV  )ODQJHG:UHQFKRSHUDWHGIRU
6HDOV  
 GLDPHWHUVXSWR*HDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV 'XFWLOHLURQERG\VWDLQOHVVVWHHO73/GLVFDQGVKDIW1LWULOHOLQLQJ*HDUER[IRUGLDPHWHUV
 DQGDERYH)ODQJHGRU:DIHU/XJW\SH 
/EV6:$%& $670$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUWRDQG)IRUGLDPHWHUDQG
&KHFNYDOYHV 6WHOOLWHFRDWHG    DERYH'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH
+RUL]RQWDOSLVWRQOLIW   
&ODVV6:$%RG\
)LOWHUV 7HHW\SHILOWHUVFDUERQVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYHLQFKHVRU6SLUDO
*DVNHWV 
ZRXQGJUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
127(6
(1) Bending R=5 dia. to be used wherever possible
(2) Flanges as per ASME B16.5 for diameters up to 24" and as per (10) "Stock finish" facing for use of flat gasket
ASME B16.47 Serie 'A' for diameters 26" and above and "Smooth finish" facing for use of
(3) Single-piece wedge for diameters up to 24" and Flexible Spiral wound gasket
wedge for diameters 26" and above (11) Schedules up to 24" are acceptable for full vacuum
(4) Removable seat (12) as per GS EP PVV 147
(5) Service pressure according to temperature and supplier's
(6) recommendations. Use as per P&ID indications. (13) Butterfly valves are only allowed on cooling water service
o
Maximum temperature = 180 C (14) Thickness based on mill tolerance as per GS EP PVV 112 par.
Horizontal installation 5.2.2.2 and weld coefficient = 1 for SAW pipe
(7) Seal materials as per GS EP PVV 142 depending on operating 26 28 30 32 34 36 38 40 42 44 46
(8) conditions and fluid characteristics 10 STD XS
Swivel plug disc
(9) Firesafe and Anti-static device (15) Product Specification Level PSL-2 is required for pipe API 5L Gr.B

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO&DUERQVWHHO 5DWLQJ /EV5)
B 03
Exploration & Production
6HUYLFH &RUURVLYHK\GURFDUERQV JDVRUOLTXLGV  &2OLJKWFRUURVLRQ  &RUURVLRQ Date: 
3 mm
&RUURVLYHIODUHJDVOLQHV &2OLJKWFRUURVLRQ DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                  
/DUJHUVL]HVDFFRUGLQJWR
3LSHV 

6FKHGXOH         WDEOHEHORZ

(QGV 3( %(
0DW6SHF  $3,/*U%VHDPOHVV $3,/*U%6$:UDGLRJUDSK\
/EV6:$
žRUžHOERZV $:3%DVSHUSLSHVFKHGXOH%:žRUžHOERZV U GLD FRQFHQWULFHFFHQWULF
)LWWWLQJV
  FRXSOLQJVWHHV UHGXFHUVWHHVZHOGROHWVVZHHSROHWV
VRFNROHWV

)ODQJHV /EV5)6:$ :1$/EV5)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 

 :1/EV5)VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
*DWHYDOYHV 6WHOOLWHFRDWHG
26 <%%*HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG   
26 <%% 
/EV6:$
%DOOYDOYHV $RU$:&%%RG\$(13EDOO6HDOV  63%RU73()ORDWLQJEDOOIRUGLDPHWHUXSWR
7ULP6HDOV
 DQG7UXQQLRQPRXQWHGIRUGLDPHWHUDQGDERYH*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG 
)ORDWLQJEDOO 
/EV6:$ $670$:&%%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%% 
/EV6:$
3OXJYDOYHV $:&%VHDOV  )ODQJHGZUHQFKRSHUDWHGIRU
6HDOV  
 GLDPHWHUVXSWRJHDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV
/EV6:$%&
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUWRDQG)IRUGLDPHWHUDQGDERYH
&KHFNYDOYHV 6WHOOLWHFRDWHG   
'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
+RUL]RQWDOSLVWRQOLIW
&ODVV6:$%RG\
)LOWHUV 7HHW\SHILOWHUVFDUERQVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYHLQFKHVRU6SLUDOZRXQG
*DVNHWV 
JUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
NOTES
(8) Swivel plug disc
(1) Bending R=5 dia. To be used wherever possible (9) Firesafe and Anti-static device
(2) Flanges as per ASME B16.5 for diameter up to 24" and as per (10) "Stock finish" facing for use of flat gasket and "Smooth
ASME B16.47 Serie 'A' for diameter 26" and above (11) finish" facing for use of Spiral wound gasket
(3) Single-piece wedge for diameters up to 24" and Flexible Schedules up up to 24" are acceptable for full vacuum
wedge for diameters 26" and above (12) as per GS EP PVV 147
(4) Removable seat (13) Thickness based on mill tolerance as per GS EP PVV 112 para
(5) Service pressure according to temperature and supplier's 5.2.2.2 and weld coeficient = 1 for SAW pipe
Recommendations. Use as per P&ID indications. 26 28 30 32 34 36 38 40 42 44 46
o STD 20 XS
Maximum temperature = 180 C
(6) Horizontal installation (14) Product Specification Level PSL-2 is required for pipe API 5L Gr.B
(7) Seal materials as per GS EP PVV 142 depending (15) For Piping stress purpose on 12" LP Flare line, sch XS shall be used
on operating conditions and fluid characteristics from 1m before the latest support located on upstream of the expansion
loop up to 2 m after the first vertical support on the FP2

(16) For Piping stress purpose on 12" LP Flare line,all elbow which located
on MCP platform shall be reinforced with sch XS

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS GS EP PVV 112

CLASS
0DWHULDO&DUERQVWHHO 5DWLQJ /EV5)
B 05
Exploration & Production
6HUYLFH &RUURVLYH+\GURFDUERQV JDVRUOLTXLGV  &RUURVLRQ Date: 
5 mm (12)
&2PHGLXPFRUURVLRQ DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                  
6FKHGXOH  ;;6    67'  67'  ;6 
3LSHV

(QGV 3( %(
0DW6SHF  $3,/*U%VHDPOHVV $3,/*U%6HDPOHVV6$: UDGLRJUDSK\

/EV6:$ž
$:3%DVSHUSLSHVFKHGXOH%:žRUžHOERZV U GLD FRQFHQWULFH[FHQWULF
)LWWWLQJV RUžHOERZV  
UHGXFHUVWHHVZHOGROHWVVZHHSROHWV 
FRXSOLQJVWHHVVRFNROHWV
/EV5)6:$ :1/EV5)$KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 
)ODQJHV
 :1/EV5)RULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ

/EV6:$
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
*DWHYDOYHV 6WHOOLWHFRDWHG
26 <%%*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
26 <%% 
/EV6:$ $RU$:&%%RG\$(13EDOO6HDOV  63%RU73()ORDWLQJEDOOIRUGLDPHWHUXSWR
%DOOYDOYHV
7ULP6HDOV DQG7UXQQLRQPRXQWHGIRUGLDPHWHUVDQGDERYH*HDUER[IRUGLDPHWHUVDQGDERYH

)ORDWLQJEDOO  )ODQJHG 
/EV6:$ $670$:&%%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%% 
/EV6:$
3OXJYDOYHV $:&%6HDOV  )ODQJHGZUHQFKRSHUDWHGIRU
6HDOV  
 GLDPHWHUVXSWRJHDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV
/EV6:$%&
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH'XDO
&KHFNYDOYHV 6WHOOLWHFRDWHG   
3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
+RUL]RQWDOSLVWRQOLIW
&ODVV6:$%RG\
)LOWHUV 7HHW\SHILOWHUVFDUERQVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUDERYHLQFKHVRU6SLUDOZRXQG
*DVNHWV 
JUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGVXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
NOTES
(1) Connections to be calculated for application (9) Swivel plug disc
(2) Bending R=5 dia. to be used wherever possible (10) Firesafe and Anti-static device
(3) Flanges as per ASME B16.5 for diameters up to 24" and as per (11) "Stock finish" facing for use of flat gasket and "Smooth
ASME B16.47 Serie 'A' for diameters 26" and above finish" facing for use of Spiral wound gasket
(4) Single-piece wedge for diameters up to 24" and Flexible (12) Corrosion allowance limited to 3.1 mm only for fittings
Wedge for diameters 26" and above below 2 inches
(5) Removable seat (13) as per GS EP PVV 147
(6) Service pressure according to temperature and supplier's (14) Thickness based on mill tolerance as per GS EP PVV 112
recommendations. Use as per P&ID indications. par. 5.2.2.2 and weld coefficient = 1 for SAW pipe
o Product Specification Level PSL-2 is required for pipe API
Maximum temperature = 180 C (15)
(7) Horizontal installation 5L Gr.B
(8) Seal materials as per GS EP PVV 142 depending
on operating conditions and fluid characteristics

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
&DUERQVWHHO
0DWHULDO 5DWLQJ /EV5)
*DOYDQL]HGXSWRLQFKHV B 10
Exploration & Production
6HUYLFH ,QVWUXPHQWDLU &RUURVLRQ Date: 
1.27 mm
8WLOLW\DLU DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU     
6FKHGXOH   
3LSHV

(QGV 7(
$3,/*U%VHDPOHVV*DOYDQLVHGWR$
0DW6SHF 
&ODVV%

/EV7KUHDGHG$žRUž
)LWWWLQJV HOERZV  FRXSOLQJVWHHVWKUHDGROHWV
*DOYDQLVHGWR$&ODVV%

)ODQJHV /EVWKUHDGHG5)$*DOYDQLVHGWR
 $&ODVV%

/EVWKUHDGHG$6WHOOLWHFRDWHG
*DWHYDOYHV
26 <%% 

%DOOYDOYHV

/EVWKUHDGHG$6WHOOLWHFRDWHG
*OREHYDOYHV
26 <%%  

3OXJYDOYHV

%XWWHUIO\YDOYHV

/EVWKUHDGHG$%&6WHOOLWHFRDWHG
&KHFNYDOYHV
  +RUL]RQWDOSLVWRQOLIW
&ODVVWKUHDGHG$<7\SH
)LOWHUV
VWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNPPWKLFN
*DVNHWV  /66ZLQGLQJPPWKLFN,QWHUQDODQG
H[WHUQDOFHQWHULQJULQJVSHU$60(%
6WXGV$%+KQXWV$+]LQFSODWHG
%ROWLQJ
ELFKURPDWHWUHDWHG

0LVFHOODQHRXV 6SHFWDFOHEOLQGXSFDUERQVWHHO
NOTES
(1) Bending not permitted (6) Swivel plug disc
(2) Flanges as per ASME B16.5. " Stock finish" facing for use of (7) as per GS EP PVV 147
flat gasket "Smooth finish" facing for use of Spiral wound (8) Thickness based on mill tolerance as per GS EP PVV 112 par. 5.2.2.2
gasket (9) Product Specification Level PSL-2 is required for pipe API 5L Gr.B
(3) Single-piece wedge
(4) Removable seat
(5) Horizontal installation

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
&DUERQVWHHO
0DWHULDO 5DWLQJ /EV5)
*DOYDQL]HGXSWRLQFKHV B 13
Exploration & Production
6HUYLFH 8WLOLW\ZDWHU 1RQ&RUURVLYH &RUURVLRQ Date: 
3 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU     
6FKHGXOH  ;;6 
3LSHV

(QGV 7(
$3,/*U%VHDPOHVV*DOYDQLVHGWR$
0DW6SHF 
&ODVV%
/EV7KUHDGHG$žRUž
)LWWWLQJV HOERZV  FRXSOLQJVWHHVWKUHDGROHWV
*DOYDQLVHGWR$&ODVV%

)ODQJHV /EVWKUHDGHG5)$*DOYDQLVHGWR
 $&ODVV%

/EVWKUHDGHG$6WHOOLWHFRDWHG
*DWHYDOYHV
26 <%% 

%DOOYDOYHV

/EVWKUHDGHG$6WHOOLWHFRDWHG
*OREHYDOYHV
26 <%%  

3OXJYDOYHV

%XWWHUIO\YDOYHV

/EVWKUHDGHG$%&6WHOOLWHFRDWHG
&KHFNYDOYHV
  +RUL]RQWDOSLVWRQOLIW
&ODVVWKUHDGHG$<7\SH
)LOWHUV
VWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNPPWKLFN
*DVNHWV  /66ZLQGLQJPPWKLFN,QWHUQDODQG
H[WHUQDOFHQWHULQJULQJVSHU$60(%
6WXGV$%+KQXWV$+]LQFSODWHG
%ROWLQJ
ELFKURPDWHWUHDWHG

0LVFHOODQHRXV 6SHFWDFOHEOLQGXSFDUERQVWHHO
NOTES
(1) Bending not permitted (6) Swivel plug disc
(2) Flanges as per ASME B16.5. " Stock finish" facing for use of (7) as per GS EP PVV 147
flat gasket "Smooth finish" facing for use of Spiral wound (8) Thickness based on mill tolerance as per GS EP PVV 112 par. 5.2.2.2
gasket (9) Product Specification Level PSL-2 is required for pipe API 5L Gr.B
(3) Single-piece wedge
(4) Removable seat
(5) Horizontal installation

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
/RZ7HPSHUDWXUH&DUERQ6WHHO
0DWHULDO 5DWLQJ /EV5)
Exploration & Production
/7&6 B 23
6HUYLFH /RZ7HPSHUDWXUHK\GURFDUERQV &ROLJKWFRUURVLRQ  &RUURVLRQ Date: 
3 mm
+LJK3UHVVXUHIODUHJDV &ROLJKWFRUURVLRQ  DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                    
/DUJHUVL]HVDFFRUGLQJWRWDEOH
6FKHGXOH       
3LSHV

EHORZ
(QGV 3( %(
2
$&&&/:6DW )
0DW6SHF  $670$*U6HDPOHVV
UDGLRJUDSKHG
/EV6:
žRUžHOERZV   $:3/DVSHUSLSHVFKHGXOH%:žRUžHOERZV
)LWWWLQJV
FRXSOLQJVWHHV U GLD FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV
VRFNROHWV$/)
/EV5)6:
)ODQJHV :1/EV5)/)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJH 
$/)

:1/EV5)RULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$/)
$/&&%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
*DWHYDOYHV 6WHOOLWHFRDWHG
26 <%%*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
26 <%% 
/EV6:$/) $/)RU$/&&%RG\$/)(13EDOO6HDOV  63%RU73()ORDWLQJEDOOIRUGLDPHWHU
%DOOYDOYHV
7ULP6HDOV XSWRDQG7UXQQLRQPRXQWHGIRUGLDPHWHUVDQGDERYH*HDUER[IRUGLDPHWHUVDQGDERYH

)ORDWLQJEDOO  )ODQJHG 
/EV6:$/) $/&&%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%%  
/EV6:$/)
3OXJYDOYHV $/&&6HDOV  )ODQJHGZUHQFKRSHUDWHGIRU
6HDOV  
 GLDPHWHUVXSWRJHDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV

/EV6:$/)
$/&&%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
&KHFNYDOYHV %&6WHOOLWHFRDWHG   
'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
+RUL]RQWDOSLVWRQOLIW

&ODVV6:$/)%RG\
)LOWHUV 7HHW\SHILOWHUV$:3/FDUERQVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU

1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUDERYHLQFKHVRU6SLUDOZRXQG
*DVNHWV 
JUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%

%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGVXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
NOTES
(1) Bending not permitted (8) Swivel plug disc
(2) Flanges as per ASME B16.5 for diameters up to 24" and as (9) Firesafe and Anti-static device
per ASME B16.47 Serie 'A' for diameters 26" and above (10) "Stock finish" facing for use of flat gasket and "Smooth
(3) Single-piece wedge for diameters up to 24" and Flexible finish" facing for use of Spiral wound gasket
Wedge for diameters 26" and above (11) as per GS EP PVV 147
(4) Removable seat (12) For size 18" above, thickness calculations are performed with allowable
(5) Service pressure according to temperature and supplier's Stress values of A333 Gr.6
recommendations. Use as per P&ID indications. (13) Thickness based on mill tolerance as per GS EP PVV 112
o par. 5.2.2.2 and weld coefficient = 1 for SAW pipe
Maximum temperature = 180 C
(6) Horizontal installation 26 28 30 32 34 36 38 40 42 44 46
(7) Seal materials as per GS EP PVV 142 depending STD 20 XS
on operating conditions and fluid characteristics

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO6WDLQOHVVVWHHO73  5DWLQJ /EV5)
B 48
Exploration & Production
6HUYLFH &RUURVLYHK\GURFDUERQV +6&2KHDY\FRUURVLRQ  &RUURVLRQ Date: 
0 mm
-HW)XHO DOORZDQFH Rev: 
/XEHRLO DIWHUILOWHU  3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
6HDORLO DIWHUILOWHU  3UHVVXUH EDUV    
,QVWUXPHQWJDV DIWHUILOWHU 7HPSHUDWXUH ž&     
'LDPHWHU                  
3LSHV 

/DUJHUVL]HVDFFRUGLQJWR
6FKHGXOH  6 6 6 WDEOHEHORZ
(QGV 3( %(
0DW6SHF $73VHDPOHVVRUZHOGHG 6$: SHU$*U&ODVV UDGLRJUDSKHG
/EV6:$
)žRUžHOERZV $:3DVSHUSLSHVFKHGXOH  %:žRUžHOERZV U GLD 
)LWWWLQJV
FRXSOLQJVWHHV FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV
VRFNROHWV 
/EV5)6:
)ODQJHV $):1/EV5)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 
$)

:1/EV5)RULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$)
$&)&%RG\7ULPPDWHULDO7ULPVWHOOLWHFRDWHG26 <%%*HDUER[IRUGLDPHWHUV
*DWHYDOYHV 7ULP26 <
DQGDERYH)ODQJHG   
%%  
/EV$) $)RU$&)&%RG\7\SH7ULPPDWHULDO6HDOV  63%RU73()ORDWLQJEDOOIRU
%DOOYDOYHV
 7ULP6HDOV GLDPHWHUVXSWRDQG7UXQQLRQPRXQWHGIRUGLDPHWHUVDQGDERYH*HDUER[IRUGLDPHWHUV

6:)ORDWLQJEDOO  DQGDERYH)ODQJHG 
/EV6:$ $&)&%RG\
*OREHYDOYHV
)7ULP26 < 7ULP)ODQJHG

%%   26 <%%  
/EV6:$) $&)&%RG\7ULP6HDOV)ODQJHGZUHQFK
3OXJYDOYHV
6HDOV   RSHUDWHGIRUGLDPHWHUVXSWR*HDUER[IRUGLDPHWHUV

:UHQFKRSHUDWHG  DQGDERYH   
%XWWHUIO\YDOYHV
/EV6:$
$&)&%RG\7\SH7ULPPDWHULDO'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LV
&KHFNYDOYHV )%&    
DFFHSWDEOHLIGHQVLW\LVDERYH  
+RUL]RQWDOSLVWRQOLIW
&ODVV6:$)
)LOWHUV 7HHW\SHILOWHUV7\SH6WDLQOHVVVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYHLQFKHVRU6SLUDOZRXQG
*DVNHWV 
JUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH$73$60(%
NOTES
(1) SS TP 321 to be coated as per GS EP COR 350 (12) "Stock finish" facing
(2) Connections to be calculated for application (13) Valve bodies may be ASTM A182 F316L
(3) Bending not permitted (14) Forged steel to ASTM A182 F321 is an acceptable alternate for body
(4) Flanges as per ASME B16.5 for diameters up to 24" and materials
as per ASME B16.47 Serie 'A' for diameters 26" and above (15) Acceptable between -46ºC and -140ºC for blowdown situation only (no
(5) Single-piece wedge for diameters up to 24" and Flexible valve operated below -46ºC)
wedge for diameters 26" and above. (16) Schedules up to 24" are acceptable for full vacuum
(6) Removable seat (17) As per GS EP PVV 147. Graphite impregnated flat gaskets shall not be
(7) Service pressure according to temperature and supplier's used in case of cloride containing fluid
recommendations. Use as per P&ID indications. (18) Thickness based on mill tolerance as per GS EP PVV 112 par. 5.2.2.2
Maximum temperature = 180 C
o and weld coefficient = 1 for SAW pipe
(8) Horizontal installation 26 28 30 32 34 36 38 40 42 44 46
(9) Seal materials as per GS EP PVV 142 depending 6.35 6.35 6.35 6.35 7.14 7.14 7.92 7.92 8.74 8.74 8.74
on operating conditions and fluid characteristics mm mm mm mm mm mm mm mm mm mm mm
(10) Swivel plug disc (19) A403 WP 321 class S or class WX ful dye penetrant on the weld surface
(11) Firesafe and Anti-static device and radiographic examination after forming and heat treatment

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO6WDLQOHVVVWHHO//  5DWLQJ /EV5)
B 50
Exploration & Production
6HUYLFH &RUURVLRQLQKLELWRU &RUURVLRQ Date: 
0 mm
'HPXOVLILHU DOORZDQFH Rev: 
$QWLIRDP
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
&KHPLFDOLQMHFWLRQSURGXFWV
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU     
6FKHGXOH 6
3LSHV

(QGV 3(
0DW6SHF $8161VHDPOHVV
/EV$)/
)LWWWLQJV žRUžHOERZV
FRXSOLQJVWHHV6: 
)ODQJHV /EV5)6:$)/ 

*DWHYDOYHV
/EV$)/7ULP
%DOOYDOYHV 
VHDOV)ORDWLQJEDOO6: 
*OREHYDOYHV

3OXJYDOYHV
/EV$)/
1HHGOHYDOYHV
7ULP%%6:
/EV$)/%&6:
&KHFNYDOYHV
  +RUL]RQWDOSLVWRQOLIW
&ODVV7HHW\SH
)LOWHUV
$)/6:
1RQ&$)IODWJDVNHWVPPWKLFNRU6SLUDOZRXQGJUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFN
*DVNHWV 
LQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWR$73
NOTES
(1) Bending not permitted (5) Seal materials as per GS EP PVV 142 depending
(2) Per ASME B16.5, "Stock finish" facing for use of flat on operating conditions and fluid characteristics
gasket and "smooth finish" for use of Spiral wound (6) As per GS EP PVV 147. Graphite impregnated flat
gasket
gaskets shall not be used in case of clorine
(3) Removable seat containing fluid
(4) Horizontal installation (7) Firesafe and Anti-static device

(8) Grade 316L Mo shall be selected and shall ave a molybdenum

minimum content of 2.5%

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO*53&RSSHU1LFNHO 1RWH 5DWLQJ /EV))
B 90
Exploration & Production
6HUYLFH )LUHILJKWLQJZDWHU :HWV\VWHP  FRUURVLYH  &RUURVLRQ Date: 
0 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                
7KLFNQHVV PP  3HUVSHFLILFDWLRQ*6(3399DQG0DQXIDFWXUHU VVWDQGDUGVIRUEDUV
3LSHV

(QGV  %HOODQG6SLJRWW\SH
0DW6SHF  *53PDWHULDOFRQIRUPLQJWRVSHFLILFDWLRQ*6(3399
*53PDWHULDOLGHQWLFDOWRSLSHPDWHULDOFRQIRUPLQJWR
)LWWWLQJV 
VSHFLILFDWLRQ*6(3399%HOOHQGV

)ODQJHV )L[HG*53IODQJHVPDWHULDOLGHQWLFDOWRSLSHPDWHULDOGHVLJQHGWREHERQGHGWRWKHDGMDFHQW

  SLHFHRISLSHRUILWWLQJ EHOODQGVSLJRWMRLQWV FRQIRUPLQJWRVSHFLILFDWLRQ*6(3399

/EV)))ODQJHG$OX%U
*DWHYDOYHV &DVW$OX%URQ]HERG\DQGWULPWR%*UDGH&%%26 <*HDUER[
ERG\ WULPWR%&
    IRUGLDPHWLUDQGDERYH))IODQJHG
26 <%%
%DOOYDOYHV

/EV)))ODQJHG$OX%U /EV$OX%UERG\
*OREHYDOYHV
ERG\ WULPWR%& WULP%&
   
26 <%% 26 <%%))IODQJHG

3OXJYDOYHV
%XWWHUIO\YDOYHV &DVW$OX%URQ]HERG\RUFDUERQVWHHOERG\SOXVQLWULOVOHHYHDQGGLVFWR%*UDGH&
   0RQHOVKDIW*HDUER[IRUGLDPHWHUVDQGDERYHIODQJHGRUZDIHU/XJW\SH
/EV)))ODQJHG$OX%U
&KHFNYDOYHV &DVW$OXEURQ]HERG\DQGWULPWR%JUDGH&%&6ZLQJW\SH LQFRQHOVSULQJ 
ERG\ WULP%&
   RUGXDO3ODWH)ODQJHGRU:DIHU/XJ7\SH
+RUL]RQWDOSLVWRQOLIW
/EV))$OX%U%RG\
)LOWHUV 7HHW\SHILOWHUV&X1L)ODQJHG
<7\SH66RU%U6FUHHQ
1HRSUHQHIODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYH
*DVNHWV 
LQFKHV6+25(KDUGQHVVWRPD[LPXP
%ROWLQJ 6WXGV$%ZLWKWZRZDVKHUVDQG++QXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
6SHFWDFOHEOLQXSWRDQGEOLQGHUVIRUDQGDERYH&X1LWR%816DOOR\QR&LQFKLHV/EVILUHSOXJV
0LVFHOODQHRXV QRQIUHH]LQJW\SH/EV)LUHK\GUDQWVQRQIUHH]LQJW\SHV\PPHWULFDOXQLRQLQFHQWHUDQGV\PPHWULFDO
XQLRQRQVLGHVPRQLWRULQJQR]]OH%UDQG&XPDWHULDOVZLWK7RSHUDWLQJDQGEORFNLQJVHJPHQWV
NOTES
(1) All valve, etc. flanges must be flat facing as they are (6) Sizes below 1" should be avoided. Size below 1" if absoluterly
designed to connect to a GRP system. required shall be made of Cu-Ni materal identical to class B92
including for facing of flanges and gaskets
(2) Blind flanges FF shall be made of C.S material with
an overlay of Cu-Ni on the contact face (7) GRP shall be fire resistant tersted as per GS EP PVV 148 requirement
(3) Valves packing to be CRANE 1066 type, or approved equal
(4) Bores of all valves to suit pipe bores.
(5) "Grade 9 A" equals UNS alloy no C95200. UNS alloy no C95800
is an acceptable aleternate material

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO*53 1RWH 5DWLQJ /EV))
B 91
Exploration & Production
6HUYLFH &KORULQH,QMHFWLRQ &RUURVLRQ Date: 
0 mm
2SHQ'UDLQ FRUURVLYH DOORZDQFH Rev: 
6HZDJH:DWHU
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV  
7HPSHUDWXUH ž&  
'LDPHWHU                
7KLFNQHVV PP 3HUVSHFLILFDWLRQ*6(3399DQG0DQXIDFWXUHU VVWDQGDUGVIRUEDUV
3LSHV

(QGV %HOODQG6SLJRWW\SH
0DW6SHF *53PDWHULDOFRQIRUPLQJWRVSHFLILFDWLRQ*6(3399
*53PDWHULDOLGHQWLFDOWRSLSHPDWHULDOFRQIRUPLQJWR
)LWWWLQJV
VSHFLILFDWLRQ*6(3399%HOOHQGV

)ODQJHV )L[HG*53IODQJHVPDWHULDOLGHQWLFDOWRSLSHPDWHULDOGHVLJQHGWREHERQGHGWRWKHDGMDFHQWSLHFH
  RISLSHRUILWWLQJ EHOODQGVSLJRWMRLQWV FRQIRUPLQJWRVSHFLILFDWLRQ*6(3399

/EV)))ODQJHG
*DWHYDOYHV &DVW$OX%URQ]HERG\DQGWULPWR%*UDGH&%%26 <
$OX%UERG\ WULPWR
    *HDUER[IRUGLDPHWLUDQGDERYH)))ODQJHG
%&26 <%%
%DOOYDOYHV

/EV)))ODQJHG /EV$OX%UERG\
*OREHYDOYHV
$OX%UERG\ WULPWR WULP%&
   
%&26 <%% 26 <%%))IODQJHG

3OXJYDOYHV
%XWWHUIO\YDOYHV &DVW$OX%URQ]HERG\RUFDUERQVWHHOERG\SOXVQLWULOVOHHYHDQGGLVFWR%*UDGH&
   0RQHOVKDIW*HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHGRUZDIHU/XJW\SH
/EV)))ODQJHG$OX%U
&KHFNYDOYHV &DVW$OXEURQ]HERG\DQGWULPWR%JUDGH&%&6ZLQJW\SH LQFRQHOVSULQJ 
ERG\ WULP%&
   RU'XDO3ODWH)ODQJHGRU:DIHU/XJ7\SH
+RUL]RQWDOSLVWRQOLIW
/EV))$OX%U%RG\
)LOWHUV 7HHW\SHILOWHUV&X1L)ODQJHG
<7\SH66RU%U6FUHHQ
1HRSUHQHIODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYH
*DVNHWV  
LQFKHV6+25(KDUGQHVVWRPD[LPXP
%ROWLQJ 6WXGV$%ZLWKWZRZDVKHUVDQG+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG

0LVFHOODQHRXV 6SHFWDFOHEOLQXSWRDQGEOLQGHUVIRUDQGDERYH&X1LWR%816DOOR\QR&

NOTES
(1) All valve, etc. flanges must be flat facing as they are (6) Sizes below 1" and above 28" should be avoided.
designed to connect to a GRP system. (7) GRP shall be fire resistant tersted as per GS EP PVV 148 requirement
(2) Blind flanges FF shall be made of C.S material with
an overlay of Cu-Ni on the contact face
(3) Valves packing to be CRANE 1066 type, or approved equal
(4) Bores of all valves to suit pipe bores.
(5) "Grade 9 A" equals UNS alloy no C95200. UNS alloy no C95800
is an acceptable aletrnate material

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO&RSSHU1LFNHO 5DWLQJ /EV5)
B 92
Exploration & Production
6HUYLFH )LUH)LJKWLQJ:DWHU 'U\V\VWHPV  FRUURVLYH &RUURVLRQ Date: 
0 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                   
7KLFNQHVV PP                   
3LSHV

(QGV 3( %(
0DW6SHF $670%&6HDPOHVVRU$670%&DQQHDOHGDQGUDGLRJUDSKHG
/EV6:žRUž
&X1LVHDPOHVVWRJUDGH816& SHU0DQXIDFWXWHU VVWDQGDUGV DVSHUSLSHWKLFNQHVV
)LWWWLQJV HOERZVFRXSOLQJVWHHV
%:žRUžHOERZV U GLD UDGLRJUDSKHGLIZHOGHG
 VRFNROHWV&X1LWRJUDGH
FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV
816&
/EV&RPSRVLWHW\SH
)ODQJHV /DSMRLQW/EV&RPSRVLWHW\SH &6&X1L 6WXEHQGWKLFNQHVVDVSHUSLSHVFKHGXOH
&6&X1L 6WRFN
  6WRFNILQLVK%OLQGV$&X1LRYHUOD\RQWKHFRQWDFWIDFH
ILQLVK6:
/EV6:$OX%UERG\
*DWHYDOYHV &DVW$OX%URQ]HERG\DQGWULPWR%*UDGH&%%26 <
WULPWR%*U$
   *HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG
26 <%%
%DOOYDOYHV
/EV6:$OX%U /EV$OX%UERG\ 
*OREHYDOYHV
%RG\ 7ULPWR WULP%*U
  
%*U$26 <%% 26 <%%)ODQJHG
3OXJYDOYHV

%XWWHUIO\YDOYHV &DVW$OX%URQ]H%RG\DQGGLVFWR%*UDGH&0RQHOVKDIWRUFDUERQVWHHOERG\SOXVQLWULO
  VOHHYH*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHGRU:DIHU/XJW\SH

/EV6:$OX%U
&KHFNYDOYHV &DVW$OX%URQ]HERG\DQG7ULPWR%*U&%&6ZLQJW\SH LQFRQHOVSULQJ RU'XDOSODWH
ERG\ 7ULPWR%*U
  )ODQJHGRU:DIHU/XJW\SH
$+RUL]RQWDOSLVWRQOLIW
&ODVV6:$OX%U%RG\
)LOWHUV <7\SH6WDLQOHVV6WHHORU 7HHW\SHILOWHUV&X1L
EURQ]HVFUHHQ
*DVNHWV  1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYHLQFKHV

%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG

6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH&X1LWR%816DOOR\QR&LQFKHV/EVILUHSOXJV
0LVFHOODQHRXV QRQIUHH]LQJW\SH/EV)LUHK\GUDQWVQRQIUHH]LQJW\SHV\PHWULFDOXQLRQLQFHQWUHDQGV\PHWULFDOXQLRQ
RQVLGHVPRQLWRULQJQR]]OH%UDQG&XPDWHULDOVZLWK7RSHUDWLQJDQGEORFNLQJVHJPHQWV
NOTES
(1) Branch connections to be reinforced as necessary (5) "Grade 9A" equals to UNS alloy no. C95 200.
accordance with BS MA 18 UNS alloy no. C95 800 is an acceptable alternate material
(2) Composite flanges to have stub ends in Cu-Ni to (6) "Stock finish" facing
BS EN 1652 Gr CW352H with loose flange in CS, the (7) As per GS EP PVV 147
drilling and outside dimensions of which per ASME B16.5,
bore to suit pipe and inner flange OD.
(3) Valve packing to be CRANE 1066 or approved equal
(4) Bores of all valves to suit pipe bores

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO*536673  5DWLQJ /EV))
B 93
Exploration & Production
6HUYLFH &RUURVLYHSURFHVVZDWHU &RUURVLRQ Date: 
0 mm
3RUWDEOHGULQNLQJZDWHU DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                
7KLFNQHVV PP  3HUVSHFLILFDWLRQ*6(3399DQG0DQXIDFWXUHU VVWDQGDUGVIRUEDUV
3LSHV

(QGV  %HOODQG6SLJRWW\SH
0DW6SHF  *53PDWHULDOFRQIRUPLQJWRVSHFLILFDWLRQ*6(3399
*53PDWHULDOLGHQWLFDOWRSLSHPDWHULDOFRQIRUPLQJWR
)LWWWLQJV 
VSHFLILFDWLRQ*6(3399%HOOHQGV

)ODQJHV )L[HG*53IODQJHVPDWHULDOLGHQWLFDOWRSLSHPDWHULDOGHVLJQHGWREHERQGHGWRWKHDGMDFHQW

  SLHFHRISLSHRUILWWLQJ EHOODQGVSLJRWMRLQWV FRQIRUPLQJWRVSHFLILFDWLRQ*6(3399

/EV)))ODQJHG
*DWHYDOYHV $&)&%RG\7ULPPDWHULDO7ULPVWHOOLWHFRDWHG26 <%%*HDUER[
$OX%UERG\ WULPWR
  IRUGLDPHWHUDQGDERYH)ODQJHG   
%&26 <%% 
/EV)))ODQJHG$ $)RU$&)&%RG\7\SH7ULPPDWHULDO6HDOV  63%RU73()ORDWLQJEDOO
%DOOYDOYHV
)7ULP6HDOV IRUGLDPHWHUVXSWRDQG7UXQQLRQPRXQWHGIRUGLDPHWHUVDQGDERYH*HDUER[IRU
   
)ORDWLQJEDOO  GLDPHWHUVDQGDERYH)ODQJHG 
/EV)))ODQJHG$ $&)&%RG\
*OREHYDOYHV
)7ULP26 <%% 7ULP26 <%%
 
   )ODQJHG   
/EV)))ODQJHG$ $&)&%RG\7ULP6HDOV  )ODQJHG
3OXJYDOYHV    )6HDOV  :UHQFK ZUHQFKRSHUDWHGIRUGLDPHWHUVXSWRJHDUER[IRU
RSHUDWHG GLDPHWHUVDQGDERYH 
%XWWHUIO\YDOYHV $&)&%RG\7ULPPDWHULDO7ULPVWHOOLWHFRDWHG*HDUER[IRUGLDPHWHUDQGDERYH
  )ODQJHG 
/EV)))ODQJHG%&
&KHFNYDOYHV $&)&%RG\7\SH7ULPPDWHULDO'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG
$)   +RUL]RQWDO
  %& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
SLVWRQOLIW
/EV)))ODQJHG$)
)LOWHUV 7HHW\SHILOWHUV736WDLQOHVVVWHHO
<W\SHVWDLQOHVVVWHHOVWUDLQHU
1HRSUHQHIODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRU
*DVNHWV 
GLDPHWHUVDERYHLQFKHV6+25(KDUGQHVVWRPD[LPXP
%ROWLQJ 6WXGV$%0FODVV+KQXWV$*U0$

0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH$73

NOTES
(1) SS TP 321 to coated as per GS EP COR 350 (8) Sizes below 1" should be avoided. Sizes below 1" if absolutely
(2) All valve, etc., flanges up to 28" must be flat facing as they are required shall be made of Stainless steel material identical to
designed to connect to a GRE system class B48, including for facing of flanges and gaskets

(3) Blind flanges shall be made of C.S. material with an overlay of Cu-Ni (9) Horizontal installation
on the contact face (10) Seal materials as per GS EP PVV 142 depending on operating
(4) Bores of all valves to suit pipe bores conditions and fluid characteristics
(5) Single-piece wedge for diameters up to 24" and Flexible wedge for (11) Swivel plug disc
diameters 26" and above (12) Forged steel to ASTM A182 F321 is an acceptable alternate for body
(6) Service pressure according to temperature and supplier’s materials
recommendations. Use as per P&ID indications. Maximum (13) Fire safe and Anti-static device
temperature = 180°C
(7) Removable seat

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO*53&RSSHU1LFNHO 5DWLQJ /EV))
B 95
Exploration & Production
6HUYLFH 3RUWDEOHZDWHU'ULQNLQJZDWHU &RUURVLRQ Date: 
0 mm
8WLOLW\ZDWHU FRUURVLYH  DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                
7KLFNQHVV PP  3HUVSHFLILFDWLRQ*6(3399DQG0DQXIDFWXUHU VVWDQGDUGVIRUEDUV
3LSHV

(QGV  %HOODQG6SLJRWW\SH
0DW6SHF  *53PDWHULDOFRQIRUPLQJWRVSHFLILFDWLRQ*6(3399
*53PDWHULDOLGHQWLFDOWRSLSHPDWHULDOFRQIRUPLQJWR
)LWWWLQJV 
VSHFLILFDWLRQ*6(3399%HOOHQGV

)ODQJHV )L[HG*53IODQJHVPDWHULDOLGHQWLFDOWRSLSHPDWHULDOGHVLJQHGWREHERQGHGWRWKHDGMDFHQWSLHFH

  RISLSHRUILWWLQJ EHOODQGVSLJRWMRLQWV FRQIRUPLQJWRVSHFLILFDWLRQ*6(3399

/EV)))ODQJHG
*DWHYDOYHV &DVW$OX%URQ]HERG\DQGWULPWR%*UDGH&%%26 <*HDUER[IRU
$OX%UERG\ WULPWR
    GLDPHWLUDQGDERYH)))ODQJHG
%&26 <%%
%DOOYDOYHV

/EV)))ODQJHG /EV$OX%UERG\
*OREHYDOYHV
$OX%UERG\ WULPWR WULP%&
   
%&26 <%% 26 <%%))IODQJHG

3OXJYDOYHV
%XWWHUIO\YDOYHV &DVW$OX%URQ]HERG\RUFDUERQVWHHOERG\SOXVQLWULOVOHHYHDQGGLVFWR%*UDGH&0
   VKDIW*HDUER[IRUGLDPHWHUVDQGDERYHIODQJHGRUZDIHU/XJW\SH
/EV)))ODQJHG$OX%U
&KHFNYDOYHV &DVW$OXEURQ]HERG\DQGWULPWR%JUDGH&%&6ZLQJW\SH LQFRQHOVSULQJ 
ERG\ WULP%&
   RUGXDO3ODWH)ODQJHGRU:DIHU/XJ7\SH
+RUL]RQWDOSLVWRQOLIW
/EV))$OX%U%RG\
)LOWHUV 7HHW\SHILOWHUV&X1L)ODQJHG
<7\SH66RU%U6FUHHQ
1HRSUHQHIODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYH
*DVNHWV 
LQFKHV6+25(KDUGQHVVWRPD[LPXP
%ROWLQJ 6WXGV$%ZLWKWZRZDVKHUVDQG++QXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
6SHFWDFOHEOLQXSWRDQGEOLQGHUVIRUDQGDERYH&X1LWR%816DOOR\QR&LQFKLHV/EVILUHSOXJVQR
0LVFHOODQHRXV IUHH]LQJW\SH/EV)LUHK\GUDQWVQRQIUHH]LQJW\SHV\PPHWULFDOXQLRQLQFHQWHUDQGV\PPHWULFDOXQLRQRQVLG
PRQLWRULQJQR]]OH%UDQG&XPDWHULDOVZLWK7RSHUDWLQJDQGEORFNLQJVHJPHQWV
NOTES
(1) All valve, etc. flanges must be flat facing as they are (6) Sizes below 1" should be avoided. Size below 1" if absoluterly
designed to connect to a GRP system. required shall be made of Cu-Ni materal identical to class B92
including for facing of flanges and gaskets
(2) Blind flanges FF shall be made of C.S material with an
overlay of Cu-Ni on the contact face
(3) Valves packing to be CRANE 1066 type, or approved equal
(4) Bores of all valves to suit pipe bores.
(5) "Grade 9 A" equals UNS alloy no C95200. UNS alloy no C95800
is an acceptable aletrnate material

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO&DUERQVWHHO 5DWLQJ /EV5)
D 05
Exploration & Production
6HUYLFH &RUURVLYHK\GURFDUERQV &2PHGLXPFRUURVLRQ &RUURVLRQ Date: 
5 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                  
/DUJHUVL]HDFFRULQJ
6FKHGXOH  ;;6  
3LSHV

60 XS
WRWDEHOEHORZ
(QGV 3( %(
0DW6SHF $3,/*U%VHDPOHVV $3,/*U%6$:UDGLRJUDSKHG
/EV6:$ž
$:3%DVSHUSLSHVFKHGXOH%:žRUžHOERZV U GLD 
)LWWWLQJV RUžHOERZV  
FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVZHHSROHWV 
FRXSOLQJVWHHVVRFNROHWV

)ODQJHV /EV5)6:$ $:1/EV5)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 

 :1/EV5)2ULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
*DWHYDOYHV 6WHOOLWHFRDWHG
26 <%%*HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG  
26 <%% 
/EV6:$ $RU$:&%%RG\$(13EDOO6HDOV  63%RU73(
%DOOYDOYHV
7ULP6HDOV )ORDWLQJEDOOIRUGLDPHWHUXSWRDQG7UXQQLRQPRXQWHGIRUGLDPHWHUVDQGDERYH

)ORDWLQJEDOO  *HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG 
/EV6:$ $670$:&%%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%% 
/EV6:$
3OXJYDOYHV $:&%6HODV  )ODQJHGZUHQFKRSHUDWHGIRUGLDPHWHUV
6HDOV  
 XSWR*HDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV
/EV6:$%&
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH
&KHFNYDOYHV 6WHOOLWHFRDWHG   
'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
+RUL]RQWDOSLVWRQOLIW
&ODVV6:$%RG\<
)LOWHUV 7HHW\SHILOWHUVFDUERQVWHHO
7\SHVWDLQOHVVVWHHOVWUDLQHU
1RQ&$)IODWJDVNHWVPPWKLFNIRUGLDPHWHUVXSWRLQFKHVDQGPPWKLFNIRUGLDPHWHUVDERYHLQFKHVRU6SLUDOZRXQG
*DVNHWV 
JUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
NOTES
(1) Connections to be calculated for application (8) Seal materials as per GS EP PVV 142 depending
(2) Bending R = 5 dia. to be used wherever possible on operating conditions and fluid characteristics
(3) Flanges as per ASME B16.5 for diameters up to 24" and as per (9) Swivel plug disc
ASME B16.47 Serie 'A' for diameters 26" and above (10) Firesafe and Anti-static device
(4) Single-piece wedge for diameters up to 24" and Flexible (11) "Stock finish" facing for use of flat gasket
wedge for diameters 26" and above and "Smooth finish" facing for use of
(5) Removable seat Spiral wound gasket
(6) Service pressure according to temperature and supplier's (13) As per GS EP PVV 147
recommendations. Use as per P&ID indications. (14) Thickness based on mill tolerance as per
Maximum temperature = 180 oC GS EP PVV 112 par. 5.2.2.2 and
(7) Horizontal installation weld coefficient = 1 for SAW pipe
26 28 30 32 34 36 38 40 42 44 46
19.5 20.62 20.62 22.23 23.83 23.83 25.40 26.97 26.97 28.58 30.18
mm mm mm mm mm mm mm mm mm mm mm

(15) Product Specification Level PSL-2 is required for pipe API 5L Gr.B

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO&DUERQVWHHO 5DWLQJ /EV5)
F 03
Exploration & Production
6HUYLFH &RUURVLYHK\GURFDUERQV JDVRUOLTXLGV  &2OLJKWFRUURVLRQ  &RUURVLRQ Date: 
3 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU                  
/DUJHUVL]HVDFFRUGLQJWR
6FKHGXOH     WDEOHEHORZ
3LSHV

(QGV 3( %(
$3,/*U%VHDPOHVV‘OHVVWKDQ´DQG6$:
0DW6SHF  $3,/;6$:UDGLRJUDSKHG
UDGLRJUDSKHG‘DQGDERYH

/EV6:$
$:3%DVSHUSLSHVFKHGXOH%:žRUžHOERZV U GLD FRQFHQWULFHFFHQWULFUHGXFHUV
)LWWWLQJV žRUžHOERZV  
WHHVZHOGROHWVVZHHSROHWV  
FRXSOLQJVWHHVVRFNROHWV

)ODQJHV /EV5)6:$ :1/EV5)$KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV  

 :1/EV5)2ULILFHIODQJHDVSHU$60(%VXSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUVWRDQG)IRUGLDPHWHUVDQGDERYH26 <
*DWHYDOYHV 6WHOOLWHFRDWHG
%%*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
26 <%% 
/EV6:$
%DOOYDOYHV $RU$:&%%RG\$(13EDOO6HDOV  63%RU73(7UXQQLRQPRXQWHG*HDUER[IRU
7ULP6HDOV
 GLDPHWHUDQGDERYH)ODQJHG 
)ORDWLQJEDOO 
/EV6:$ $670$:&%%RG\
*OREHYDOYHV 6WHOOLWHFRDWHG )7ULP)ODQJHG
26 <%%   26 <%%  
/EV6:$
3OXJYDOYHV $:&%VHDOV  )ODQJHGZUHQFKRSHUDWHGIRU
6HDOV  
 GLDPHWHUVXSWRJHDUER[IRUGLDPHWHUVDQGDERYH
:UHQFKRSHUDWHG
%XWWHUIO\YDOYHV
/EV6:$%&
$:&%%RG\7ULPVWHOOLWHFRDWHGIRUGLDPHWHUWRDQG)IRUGLDPHWHUDQGDERYH
&KHFNYDOYHV 6WHOOLWHFRDWHG   
'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\LVDERYH 
+RUL]RQWDOSLVWRQOLIW
&ODVV6:$%RG\
)LOWHUV 7HHW\SHILOWHUVFDUERQVWHHO
<7\SHVWDLQOHVVVWHHOVWUDLQHU

*DVNHWV  6SLUDOZRXQGJUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%

%ROWLQJ 6WXGV$%+KQXWV$+]LQFSODWHGELFKURPDWHWUHDWHG
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYHFDUERQVWHHO
NOTES
(8) Swivel plug disc
(1) Bending R=5 dia. To be used wherever possible (9) Firesafe and Anti-static device
(2) Flanges as per ASME B16.5 for diameter up to 24" and as per (10) "Smooth finish" facing
ASME B16.47 Serie 'A' for diameter 26" and above (11) For diameters 26 inches and above, fittings according to A860 WPHY60,
(3) Single-piece wedge for diameters up to 24" and Flexible wall thickness to suit matching pipe
wedge for diameters 26" and above (12) For diameters 26 inches and above, flanges per ASTM A694
(4) Removable seat grade F60,to match pipe wall thickness.
(5) Service pressure according to temperature and supplier's (13) As per GS EP PVV 147
Recommendations. Use as per P&ID indications. (14) Minimum calculated thickness for pipe diameter 26" and above
o Thickness based on mill tolerance as per GS EP PVV 112 para
Maximum temperature = 180 C (15)
(6) Horizontal installation 5.2.2.2 and weld coeficient = 1 for SAW pipe
(7) Seal materials as per GS EP PVV 142 depending 26 28 30 32 34 36 38 40 42 44 46
on operating conditions and fluid characteristics 24.1mm 25.6mm 27.2mm 28.8mm 30.4mm 32.0mm 33.6mm 35.2mm 36.8mm 38.4mm 40.0mm

(16) Product Specification Level PSL-2 is required for pipe API 5L Gr.B and
API5L X60

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

/EV5) CLASS
0DWHULDO6WDLQOHVVVWHHO73  5DWLQJ
6PRRWKILQLVK
Exploration & Production
F 48
6HUYLFH &RUURVLYHK\GURFDUERQV +6&2KHDY\FRUURVLRQ  &RUURVLRQ Date: 
0 mm
6HDO*DV DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&     
'LDPHWHU                  
/DUJHUVL]HVDFFRUGLQJ
6FKHGXOH  6 6 6 
3LSHV

WRWDEOHEHORZ
(QGV 3( %(
0DW6SHF $736HDPOHVV‘OHVVWKDQRUZHOGHG (): SHU$670$*UFODVV 5DGLRJUDS\
/EV$)
6:RRUHOERZV $:3DVSHUSLSHVFKHGXOH  %:RUHOERZV U GLD 
)LWWWLQJV
FRXSOLQJVWHHV FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV 
VRFNROHWV 
/EV5)6:
)ODQJHV :1/EV5)$)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV 
$)

:1/EV5)6XSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:$)
$&)&%RG\7ULPPDWHULDO7ULPVWHOOLWHFRDWHG26 <%%
*DWHYDOYHV 7ULP26 <%%
*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
 
/EV$)
%DOOYDOYHV $)RU$&)&%RG\7\SH7ULPPDWHULDO6HDOV  63%RU73(7UXQQLRQPRXQWHG
7ULP6HDOV6:
 *HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG 
)ORDWLQJ%DOO 
/EV6:$) $&)&%RG\
*OREHYDOYHV
7ULP26 < 7ULP26 <%%
 
%%  )ODQJHG 
/EV6: $&)&%RG\7ULP6HDOV  )ODQJHG
3OXJYDOYHV
$)6HDOV   ZUHQFKRSHUDWHGIRUGLDPHWHUVXSWR

:UHQFKRSHUDWHG  JHDUER[IRUGLDPHWHUVDQGDERYH 
%XWWHUIO\YDOYHV
OEV6:%&
$&)&%RG\7\SH7ULPPDWHULDO'XDO3ODWH :DIHU/XJW\SH 
&KHFNYDOYHV $)    
6ZLQJW\SH IODQJHG%& LVDFFHSWDEOHLIGHQVLW\DERYH  
+RUL]RQWDOSLVWRQOLIW
/EV6:$)
)LOWHUV 7HHW\SHILOWHUV736WDLQOHVVVWHHO
<W\SHVWDLQOHVVVWHHOVWUDLQHU
*DVNHW  6SLUDOZRXQGJUDSKLWHILOOHUPPWKLFN/66ZLQGLQJPPWKLFNLQWHUQDODQGH[WHUQDOFHQWHULQJULQJVSHU$60(%
%ROWLQJ 6WXG$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH$73
NOTES
(1) SS TP 321 to be coated as per GS EP COR 350 (11) Firesafe and Anti-static device
(2) Connections to be calculated for application (12) "Smooth finish" facing
(3) Bending not permitted (13) Valves bodies may be ASTM A182 F316L. Grade 316L Mo shall be
(4) Flanges as per ASME B16.5 for diameters up to 24" and as selected and shall have a molybdenum minimum content of 2.5%
per ASME B16.47 Serie 'A' for diameters 26" and above (14) Forged steel to ASTM A182 F321 is an acceptable alternate
(5) Single-piece wedge for diameters up to 24" and Flexible for body materials
wedge for diameters 26" and above (15) o o
Acceptable between -46 C and 140 C for blow down
(6) Removable seat o
situation only (no valve operated below -46 C)
(7) Service pressure according to temperature and supplier's (16) As per GS EP PVV 147
recommendations. Use as per P&ID indications. (17) Thickness based on mill tolerance as per GS EP PVV 112
o
Maximum temperature = 180 C §.5.2.2.2 and weld coeficient = 1 for EFW pipe
(8) Horizontal installation 26 28 30 32 34 36 38 40 42 44 46
(9) Seal materials as per GS EP PVV142 depending 25.2 27.1 29 31 32.9 34.8 36.8 38.7 40.6 42.6 44.5
on operating conditions and fluid characteristics mm mm mm mm mm mm mm mm mm mm mm
(10) Swivel plug disc (18) A403 WP 321 class S or class WX full dye penetrant on the weld surface
and radiographic examination after forming and heat treatment

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO6WDLQOHVVVWHHO73  5DWLQJ /EV5-

Exploration & Production

G 48
6HUYLFH &RUURVLYHK\GURFDUERQ +6&2KHDY\FRUURVLRQ &RUURVLRQ Date: 
0 mm
DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&     
'LDPHWHU                  
       
6FKHGXOH  6 7REHFDOFXODWHG
3LSHV

PP PP PP PP PP PP PP PP

(QGV 3( %(
0DW6SHF $736HDPOHVV‘OHVVWKDQRUZHOGHG (): SHU$670$*UFODVV 5DGLRJUDSHG
/EV$)
6:RRUHOERZV $:3DVSHUSLSHVFKHGXOH  %:RUHOERZV U GLD 
)LWWWLQJV
FRXSOLQJVWHHV FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV 
VRFNROHWV 
/EV5-6:
)ODQJHV :1/EV5-$)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV+%PLQ 
$)

:1/EV5-2ULILFHIODQJHDVSHU$60(%6XSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:
$&)&%RG\7ULPPDWHULDO7ULPVWHOOLWHFRDWHG26 <%%
*DWHYDOYHV $)7ULP
*HDUER[IRUGLDPHWHUDQGDERYH)ODQJHG   
26 <%%  
/EV$)
%DOOYDOYHV $)RU$&)&%RG\7\SH7ULPPDWHULDO6HDOV  63%RU73(
 7ULP6HDOV6:
 7UXQQLRQPXRQWHG*HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHG 
)ORDWLQJ%DOO 
/EV6:$ $&)&%RG\
*OREHYDOYHV )7ULP26 < 7ULP26 <%%
%%    )ODQJHG 
/EV6: $&)&%RG\7ULP6HDOV  )ODQJHG
3OXJYDOYHV
$)6HDOV   ZUHQFKRSHUDWHGIRUGLDPHWHUVXSWR

:UHQFKRSHUDWHG  *HDUER[IRUGLDPHWHUVDQGDERYH 
%XWWHUIO\YDOYHV
OEV6:%&
$&)&%RG\7\SH7ULPPDWHULDO'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG%& LV
&KHFNYDOYHV $)    
DFFHSWDEOHLIGHQVLW\DERYH  
+RUL]RQWDOSLVWRQOLIW
/EV6:$)
)LOWHUV 7HHW\SHILOWHUV736WDLQOHVVVWHHO
<W\SHVWDLQOHVVVWHHOVWUDLQHU
*DVNHW 2FWRJRQDO5LQJ-RLQW73/66SHU$60(%+%PD[/EVUDWLQJ
%ROWLQJ 6WXG$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH$73
NOTES
(1) SS TP 321 to be coated as per GS EP COR 350 (9) Seal materials as per GS EP PVV142 depending on
(2) Connections to be calculated for application operating conditions and fluid characteristics
(3) Bending not permitted (10) Swivel plug disc
(4) Flanges as per ASME B16.5 for diameters up to 24" and as (11) Firesafe and Anti-static device
per ASME B16.47 Serie 'A' for diameters 26" and above
(12) Ring joint facing, minimum hardness 150 HB
(13) Valves bodies may be ASTM A182 F316L. Grade 316L Mo shall be
(5) Single-piece wedge for diameters up to 24" and Flexible
selected and shall have a molybdenum minimum content of 2.5%
wedge for diameters 26" and above
(14) Forged steel to ASTM A182 F321 is an acceptable alternate for
(6) Removable seat body materials
o o
(7) Service pressure according to temperature and supplier's (15) Acceptable between -46 C and 140 C for blow down situation
recommendations. Use as per P&ID indications. only (no valve operated below -46 C) o
o
Maximum temperature = 180 C (16)
(8) Horizontal installation EFW
(17) A403 WP 321 class S or class WX full dye penetrant on the weld
surface and radiographic examination after forming and heat treatment

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO6WDLQOHVVVWHHO73  5DWLQJ /EV5-

Exploration & Production

H 48
6HUYLFH &RUURVLYHK\GURFDUERQ +6&2KHDY\FRUURVLRQ &RUURVLRQ Date: 
0 mm
&RUURVLRQ,QKLELWRU DOORZDQFH Rev: 
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
3UHVVXUH EDUV    
7HPSHUDWXUH ž&     
'LDPHWHU                  
6FKHGXOH  6  ;;6  7REHFDOFXODWHG
3LSHV

(QGV 3( %(
0DW6SHF $736HDPOHVV‘OHVVWKDQRUZHOGHG (): SHU$670$*UFODVV 5DGLRJUDSHG
/EV$)
6:RRUHOERZV $:3DVSHUSLSHVFKHGXOH  %:RUHOERZV U GLD 
)LWWWLQJV
FRXSOLQJVWHHV FRQFHQWULFHFFHQWULFUHGXFHUVWHHVZHOGROHWVVZHHSROHWV 
VRFNROHWV 
/EV5-6: :1/EV5-$)KXEWKLFNQHVVDVSHUSLSHVFKHGXOHEOLQGIODQJHV+%PLQ 
)ODQJHVRU+XE $) RU+XE&RQQHFWRU 
&RQQHFWRUV
:1/EV5-2ULILFHIODQJHDVSHU$60(%6XSSOLHGZLWKEROWLQJIRULQVWUXPHQWFRQQHFWLRQ
/EV6:
$&)&%RG\7ULPPDWHULDO  7ULPVWHOOLWHFRDWHG26 <%%
*DWHYDOYHV $)7ULP
*HDUER[IRUGLDPHWHUDQGDERYH  )ODQJHGRU+XEFRQQHFWRU
26 <%%  
/EV$)
%DOOYDOYHV $)RU$&)&%RG\7\SH7ULPPDWHULDO6HDOV  63%RU73(
7ULP6HDOV6:
 7UXQQLRQPXRQWHG*HDUER[IRUGLDPHWHUVDQGDERYH)ODQJHGRUKXEFRQQHFWRU
)ORDWLQJ%DOO   
/EV6:$ $&)&%RG\
*OREHYDOYHV
)7ULP26 < 7ULP26 <%%
 
%%  )ODQJHG 
/EV6: $&)&%RG\7ULP6HDOV  )ODQJHGRUKXE
3OXJYDOYHV
$)6HDOV   FRQQHFWRUZUHQFKRSHUDWHGIRUGLDPHWHUV

:UHQFKRSHUDWHG  *HDUER[IRUGLDPHWHUVDQGDERYH
%XWWHUIO\YDOYHV
OEV6:%&
$&)&%RG\  7\SH7ULPPDWHULDO'XDO3ODWH :DIHU/XJW\SH 6ZLQJW\SH IODQJHG
&KHFNYDOYHV $)    
%& LVDFFHSWDEOHLIGHQVLW\DERYH  
+RUL]RQWDOSLVWRQOLIW
/EV6:$)
)LOWHUV 7HHW\SHILOWHUV736WDLQOHVVVWHHO
<W\SHVWDLQOHVVVWHHOVWUDLQHU
2FWRJRQDO5LQJ-RLQW73/66SHU$60(%+%PD[/EVUDWLQJRUULQJSHUKXEFRQQHFWRUPDQXIDFWXUHU
*DVNHW
6WDQGDUG
%ROWLQJ 6WXG$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQGXSWRDQGEOLQGHUVIRUDQGDERYH$73
NOTES
(1) SS TP 321 to be coated as per GS EP COR 350 (10) Swivel plug disc
(2) Connections to be calculated for application (11) Firesafe and Anti-static device
(12) Forged steel to ASTM A 182 F321 is an acceptable alternate for body
(3) Bending not permitted
materials
Ring joint facing, minimum hardness 150 HB Flanges as per (13) o o
(4) Acceptable between -46 C and 140 C for blow down situation
ASME B16.5 for diameters up to 24" o
only (no valve operated below -46 C)
(5) Single-piece wedge for diameters up to 24" and Flexible (14) Gearbox for diameters 3" and above
wedge for diameters 26" and above (15) Valves bodies may be ASTM A182 F316L. Grade 316L Mo shall be
(6) Removable seat selected and shall have a molybdenum minimum content of 2.5%
(7) Service pressure according to temperature and supplier's (16) Thickness based on mill tolerance as per GS EP PVV 112
recommendations. Use as per P&ID indications. §.5.2.2.2 and weld coeficient = 1 for SAW pipe
o
Maximum temperature = 180 C (17) A403 WP 321 class S or class WX full dye penetrant on the weld
(8) Horizontal installation surface and radiographic examination after forming and heat treatment

(9) Seal materials as per GS EP PVV142 depending on (18) Hub connector for NPS 12” and above. Hub connector shall be all of the
operating conditions and fluid characteristics same Manufacturer. One standard ring per size required

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 PIPING MATERIALS As per GS EP PVV 112

CLASS
0DWHULDO6WDLQOHVVVWHHO// 5DWLQJ /EV5)
H 50
Exploration & Production
6HUYLFH &RUURVLRQLQKLELWRU &RUURVLRQ Date: 
0 mm
'HPXOVLILHU DOORZDQFH Rev: 
$QWLIRDP
3UHVVXUH7HPSHUDWXUH5DWLQJ *URXS
&KHPLFDOLQMHFWLRQSURGXFWV
3UHVVXUH EDUV    
7HPSHUDWXUH ž&    
'LDPHWHU    
6FKHGXOH 6
3LSHV

(QGV 3(
0DW6SHF $8161VHDPOHVV
/EV$)/
)LWWWLQJV žRUžHOERZV
FRXSOLQJVWHHV6: 
)ODQJHV /EV5-6:$)/ 

*DWHYDOYHV
%DOOYDOYHV /EV$)/7ULP
 VHDOV)ORDWLQJEDOO6: 
*OREHYDOYHV

3OXJYDOYHV
/EV$)/
1HHGOHYDOYHV
7ULP%%6:
/EV$)/%&6:
&KHFNYDOYHV
  +RUL]RQWDOSLVWRQOLIW
&ODVV7HHW\SH
)LOWHUV
$)/6:

*DVNHWV 2FWRJRQDO5LQJ-RLQW73/66SHU$60(%+%PD[/EVUDWLQJ
%ROWLQJ 6WXGV$%0FODVV+KQXWV$*U0$
0LVFHOODQHRXV 6SHFWDFOHEOLQG$73$60(%
NOTES
(1) Bending not permitted (6) Fire safe and anti-static device
Ring joint facing as per ASME B16.5, minimum (7) Grade 316L Mo shall be selected and shall have a molybdenum
(2)
hardness 150 HB minimum content of 2.5%
(3) Removable seat
(4) Horizontal installation
(5) Seal materials as per GS EP PVV 142 depending
on operating conditions and fluid characteristics

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 02 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 40 of 42

Annex 2 - Branch Reinforcement Table

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 02 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 41 of 42

Table of Connections for Steel Classes 150 Lbs to 1500 Lbs

Header

1/2 3
3/4 6 3
1 6 6 3
1½ 6 6 6 3
2 1 1 1 1 4
3 1 1 1 1 7 4
4 1 1 1 1 7 7 4
6 1 1 1 1 2 7 7 4
8 1 1 1 1 2 2 7 7 4
10 1 1 1 1 2 2 2 7 7 4
12 1 1 1 1 2 2 2 7 7 7 4
14 1 1 1 1 2 2 2 2 7 7 7 4
16 1 1 1 1 2 2 2 2 7 7 7 7 4
18 1 1 1 1 2 2 2 2 2 7 7 7 7 4
20 1 1 1 1 2 2 2 2 2 7 7 7 7 7 4
24 1 1 1 1 2 2 2 2 2 5 7 7 7 7 7 4
26 1 1 1 1 2 2 2 2 2 5 5 7 7 7 7 7 4
28 1 1 1 1 2 2 2 2 2 5 5 7 7 7 7 7 7 4
30 1 1 1 1 2 2 2 2 2 5 5 5 7 7 7 7 7 7 4
32 1 1 1 1 2 2 2 2 2 5 5 5 7 7 7 7 7 7 7 4
34 1 1 1 1 2 2 2 2 2 5 5 5 5 7 7 7 7 7 7 7 4
36 1 1 1 1 2 2 2 2 2 5 5 5 5 7 7 7 7 7 7 7 7 4
½ ¾ 1 1½ 2 3 4 6 8 10 12 14 16 18 20 24 26 28 30 32 34 36 Branch

Note: For piping class B10, use of threaded connection for 2” and below

LEGEND
1: Sockolet
2: Weldolet
3: Equal Tee Socket Weld
4: Equal Tee Butt Weld
5: Reducing Tee + Reducer or sweepolet
6: Reducing Tee Socket Weld
7: Reducing Tee Butt Weld

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03
 Doc. Ref.: MM-YAD-00-GU01-504002

CTR Reference: NA
Revision: 02 Rev Date: 30-Nov-2012
General – Piping Material Classes
Discipline: PVV Document Type: SPE

Phase: DE System / Subsystem: NA Equipment Type: NA Status: AFC Class: 1 Page 42 of 42

Table of Branch Reinforcement for Class B90, B91, B93& B95

Header

1 1

2 1
1½

2 2 1
2

3 2 2 2 1

2 2 2 2 1
4

2 2 2 2 2 1
6

8 2 2 2 2 2 2 1

2 2 2 2 2 2 2 1
10

2 2 2 2 2 2 2 2 1
12

14 2 2 2 2 2 2 2 2 2 1

2 2 2 2 2 2 2 2 2 2 1
16

1 1½ 2 3 4 6 8 10 12 14 16 Branch

Note: The branch connections shall be in accordance with Manufacturer’ standard dimension tables.

LEGEND
1: Equal Tee Bell Ends
2: Reducing Saddle

This document is the property of TOTAL E&P MYANMAR. It must not be stored, reproduced or disclosed to others without written authorisation from the Company.

MM-YAD-00-GU01-504002_rev03