Seven Segment DisplayAlmost everywhere we can find seven segment
display; it is too common so that we often do not notice it at all. From pocket calculators, digital
clocks and electronic test equipment to petrol pumps everywhere information is delivered
through seven segment display.
A single seven segment display or a combination of such display arranged in an organized
manner invariably meets our display requirement. Normally there are two types of displays are
used those are LED (Light Emitting Diode) and LCD (Liquid crystal display) types.
History of Seven Segment Display
F W Wood invented the concept of seven segment display in the year of 1908 as found in the
Patents.
It actually displayed the number four by using a diagonal bar. Later the idea was taken and the
display system used to be made by incandescent bulbs which were used in power plant boiler
room signal panels in 1910. Finally from the year 1970 the use of Seven Segment Display
became worldwide and hugely popular when it were started to made from LEDs.
The obvious question which arises now is that how the stuff
works or rather how numbers can be displayed by a Seven Segment Display. To explain the
method we assume that we are considering the display system made of separate LCDs. Now to
display the numbers we have to take 8 LCDs as shown in the picture and arrange them exactly as
shown in the figure. The design of the LCDs can be different but the arrangement has to be
exactly similar to the figure. To display the numbers from 0 to 9 the
LCDs from A to G are lightened sequentially. So for displaying a zero all the LCDs except the G
marked of the figure are turned on and we can see a zero being displayed.
Similarly to display a one only the F and E are turned on and it shows a one
And in the same way all the other digits can be shown by the
sequential turning on of various LCDs to display all the numbers. Now we will look at the
science and method behind the display of the codes.
As we
have already shown that A to G is the LED or LCD displays and they are turned on sequentially
to display the desired number. Now they have to be connected in a circuit which can be given
input signal according to the nature of desired output. The first circuit diagram is of common
cathode type and here ‘1’ means on and the individual diodes are connected as shown in the
figure and the second diagram is of common anode type and here ‘0’ means on. The DP can be
located on left or right side of the display figure. Furthermore this display figure not only can be
used to display only numbers from 0 to 9 but also they can show the letters from A to F. The
table given below gives the binary code for displaying different numeric characters as well as
different alphabetical characters both for common cathode and common anode type displays.
Seven Segment Display Code
Common catdode type ‘1’ means ON Common anode type ‘0’ means ON
A B C D E F G DP A B C D E F G DP
0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1
1 0 1 1 0 0 0 0 1 1 0 0 1 1 1 1
2 1 1 0 1 1 0 1 2 0 0 1 0 0 1 0
3 1 1 1 1 0 0 1 3 0 0 0 0 1 1 0
4 0 1 1 0 0 1 1 4 1 0 0 1 1 0 0
5 1 0 1 1 0 1 1 5 0 1 0 0 1 0 0
6 0 0 1 1 1 1 1 6 1 1 0 0 0 0 0
7 1 1 1 0 0 0 0 7 0 0 0 1 1 1 1
8 1 1 1 1 1 1 1 8 0 0 0 0 0 0 0
9 1 1 1 0 0 1 1 9 0 0 0 1 1 0 0
A 1 1 1 1 1 0 1 A 0 0 0 0 0 1 0
B 0 0 1 1 1 1 1 B 1 1 0 0 0 0 0
C 0 0 0 1 1 0 1 C 1 1 1 0 0 1 0
D 0 1 1 1 1 0 1 D 1 0 0 0 0 1 0
E 1 1 0 1 1 1 1 E 0 0 1 0 0 0 0
F 1 0 0 0 1 1 1 F 0 1 1 1 0 0 0
