AEA176Hu 96 Tests
Enzyme-linked Immunosorbent Assay Kit
For Anti-Collagen Type III Antibody (Anti-COL3)
Organism Species: Homo sapiens (Human)
Instruction manual
FOR RESEARCH USE ONLY
NOT FOR USE IN CLINICAL DIAGNOSTIC PROCEDURES
Version 13.0
[ INTENDED USE ]
The kit is an enzyme immunoassay for in vitro quantitative measurement of Anti-COL3 in human serum, plasma
and other biological fluids.
[ REAGENTS AND MATERIALS PROVIDED ]
Reagents Quantity Reagents Quantity
Pre-coated, ready to use 96-well strip plate 1 Plate sealer for 96 wells 4
Standard 2 Standard Diluent 1×20mL
Detection Reagent A 1×120μL Assay Diluent A 1×12mL
TMB Substrate 1×9mL Stop Solution 1×6mL
Wash Buffer (30 × concentrate) 1×20mL Instruction manual 1
[ MATERIALS REQUIRED BUT NOT SUPPLIED ]
1. Microplate reader with 450 ± 10nm filter.
2. Precision single or multi-channel pipettes and disposable tips.
3. Eppendorf Tubes for diluting samples.
4. Deionized or distilled water.
5. Absorbent paper for blotting the microtiter plate.
6. Container for Wash Solution
[ STORAGE OF THE KITS ]
1. For unused kit: The whole kit could be stored at -20oC in shelf life, while up to one month at 4oC.
For experiment convenience, reagents could also be stored seperately, Standard, Detection Reagent A and
96-well strip plate should be stored at -20oC while the others could be at 4 oC.
2. For opened kit: When the kit is opened, the remaining reagents still need to be stored according to the above
storage condition. Besides, please return the unused wells to the foil pouch containing the desiccant pack, and
reseal along entire edge of zip-seal.
Note:
It is highly recommended to use the remaining reagents within 1 month provided this is within the expiration date
of the kit. For the expiration date of the kit, please refer to the label on the kit box. All components are stable until
this expiration date.
[ SAMPLE COLLECTION AND STORAGE ]
Serum - Use a serum separator tube and allow samples to clot for two hours at room temperature or overnight at
4oC before centrifugation for 20 minutes at approximately 1,000×g. Assay freshly prepared serum
immediately or store samples in aliquot at -20oC or -80oC for later use. Avoid repeated freeze/thaw cycles.
Plasma - Collect plasma using EDTA or heparin as an anticoagulant. Centrifuge samples for 15 minutes at
1,000×g at 2-8oC within 30 minutes of collection. Remove plasma and assay immediately or store samples in
aliquot at -20oC or -80oC for later use. Avoid repeated freeze/thaw cycles.
Other biological fluids - Centrifuge samples for 20 minutes at 1,000×g. Collect the supernates and assay
immediately or store samples in aliquot at -20oC or -80oC for later use. Avoid repeated freeze/thaw cycles.
Note:
1. Samples to be used within 5 days may be stored at 4oC, otherwise samples must be stored at -20oC (≤1
month) or -80oC (≤2 months) to avoid loss of bioactivity and contamination.
2. Sample hemolysis will influence the result, so hemolytic specimen should not be used.
3. When performing the assay, bring samples to room temperature.
4. It is highly recommended to use serum instead of plasma for the detection based on quantity of our in-house
data.
[ REAGENT PREPARATION ]
1. Bring all kit components and samples to room temperature (18-25oC) before use.
2. Standard - Reconstitute the Standard with 0.9mL of Standard Diluent, kept for 10 minutes at room
temperature, shake gently(not to foam). The concentration of the standard in the stock solution is 200ng/mL.
Please prepare 7 tubes containing 0.5mL Standard Diluent and produce a double dilution series according to
the picture shown below. Mix each tube thoroughly before the next transfer. Set up 7 points of diluted
standard such as 200ng/mL, 100ng/mL, 50ng/mL, 25ng/mL, 12.5ng/mL, 6.25ng/mL, 3.12ng/mL, and the last
EP tubes with Standard Diluent is the blank as 0ng/mL.
Tube 1 2 3 4 5 6 7 8
ng/mL 200 100 50 25 12.5 6.25 3.12 0
3. Detection Reagent A - Briefly spin or centrifuge the stock Detection A before use. Dilute to the working
concentration with working Assay Diluent A, respectively (1:100).
4. Wash Solution - Dilute 20mL of Wash Solution concentrate (30×) with 580mL of deionized or distilled water
to prepare 600mL of Wash Solution (1×).
5. TMB substrate - Aspirate the needed dosage of the solution with sterilized tips and do not dump the residual
solution into the vial again.
Note:
1. The standard for this kit is liquid. Due to its small volume, maybe invisible to the eye.
2. Making serial dilution in the wells directly is not permitted.
3. Prepare standard within 15 minutes before assay. Please do not dissolve the reagents at 37oC directly.
4. Please carefully reconstitute Standards or working Detection Reagent A according to the instruction, and
avoid foaming and mix gently until the crystals are completely dissolved. To minimize imprecision caused by
pipetting, use small volumes and ensure that pipettors are calibrated. It is recommended to suck more than
10μL for once pipetting.
5. The reconstituted Standards and Detection Reagent A can be used only once.
6. If crystals have formed in the Wash Solution concentrate (30×), warm to room temperature and mix gently
until the crystals are completely dissolved.
7. Contaminated water or container for reagent preparation will influence the detection result.
[ SAMPLE PREPARATION ]
1. We are only responsible for the kit itself, but not for the samples consumed during the assay. The user should
calculate the possible amount of the samples used in the whole test. Please reserve sufficient samples in
advance.
2. Please predict the concentration before assaying. If values for these are not within the range of the standard
curve, users must determine the optimal sample dilutions for their particular experiments. Sample should be
diluted by PBS.
3. If the samples are not indicated in the manual, a preliminary experiment to determine the validity of the kit is
necessary.
4. Tissue or cell extraction samples prepared by chemical lysis buffer may cause unexpected ELISA results due
to the impacts from certain chemicals.
5. Due to the possibility of mismatching between antigen from other origin and antibody used in our kits (e.g.,
antibody targets conformational epitope rather than linear epitope), some native or recombinant proteins
from other manufacturers may not be recognized by our products.
6. Influenced by the factors including cell viability, cell number or sampling time, samples from cell culture
supernates may not be detected by the kit.
7. Fresh samples without long time storage is recommended for the test. Otherwise, protein degradation and
denaturalization may occur in those samples and finally lead to wrong results.
[ ASSAY PROCEDURE ]
1. Determine wells for diluted standard, blank and sample. Prepare 7 wells for standard, 1 well for blank.
Add 100μL each of dilutions of standard (read Reagent Preparation), blank and samples into the appropriate
wells. Cover with the Plate sealer. Incubate for 1 hour at 37oC.
2. Remove the liquid of each well, don’t wash.
3. Add 100μL of Detection Reagent A working solution to each well. Incubate for 1 hour at 37oC after covering
it with the Plate sealer.
4. Aspirate the solution and wash with 350μL of 1× Wash Solution to each well using a squirt bottle,
multi-channel pipette, manifold dispenser or autowasher, and let it sit for 1~2 minutes. Remove the remaining
liquid from all wells completely by snapping the plate onto absorbent paper. Totally wash 5 times. After the
last wash, remove any remaining Wash Buffer by aspirating or decanting. Invert the plate and blot it against
absorbent paper.
5. Add 90μL of Substrate Solution to each well. Cover with a new Plate sealer. Incubate for 10 - 20 minutes at
37oC (Don't exceed 30 minutes). Protect from light. The liquid will turn blue by the addition of Substrate
Solution.
6. Add 50μL of Stop Solution to each well. The liquid will turn yellow by the addition of Stop solution. Mix the
liquid by tapping the side of the plate. If color change does not appear uniform, gently tap the plate to ensure
thorough mixing.
7. Remove any drop of water and fingerprint on the bottom of the plate and confirm there is no bubble on the
surface of the liquid. Then, run the microplate reader and conduct measurement at 450nm immediately.
Note:
1. Assay preparation: Keep appropriate numbers of wells for each experiment and remove extra wells from
microplate. Rest wells should be resealed and stored at -20oC.
2. Samples or reagents addition：Please use the freshly prepared Standard. Please carefully add samples
to wells and mix gently to avoid foaming. Do not touch the well wall. For each step in the procedure, total
dispensing time for addition of reagents or samples to the assay plate should not exceed 10 minutes. This
will ensure equal elapsed time for each pipetting step, without interruption. Duplication of all standards and
specimens, although not required, is recommended. To avoid cross-contamination, change pipette tips
between additions of standards, samples, and reagents. Also, use separated reservoirs for each reagent.
3. Incubation: To ensure accurate results, proper adhesion of plate sealers during incubation steps is
necessary. Do not allow wells to sit uncovered for extended periods between incubation steps. Once
reagents are added to the well strips, DO NOT let the strips DRY at any time during the assay. Incubation
time and temperature must be controlled.
4. Washing: The wash procedure is critical. Complete removal of liquid at each step is essential for good
performance. After the last wash, remove any remaining Wash Solution by aspirating or decanting and
remove any drop of water and fingerprint on the bottom of the plate. Insufficient washing will result in poor
precision and false elevated absorbance reading.
5. Controlling of reaction time: Observe the change of color after adding TMB Substrate (e.g. observation
once every 10 minutes), if the color is too deep, add Stop Solution in advance to avoid excessively strong
reaction which will result in inaccurate absorbance reading.
6. TMB Substrate is easily contaminated. Please protect it from light.
7. The environment humidity which is less than 60% might have some effects on the final performance,
therefore, a humidifier is recommended to be used at that condition.
[ TEST PRINCIPLE ]
The microtiter plate provided in this kit has been pre-coated with COL3. Standards or samples are then added to
the appropriate microtiter plate wells with a Horseradish Peroxidase (HRP)-conjugated secondary antibody. After
TMB substrate solution is added, those wells that contain Anti-COL3 will exhibit a change in color. The
enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is
measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of Anti-COL3 in the
samples is then determined by comparing the O.D. of the samples to the standard curve.
[ CALCULATION OF RESULTS ]
Average the duplicate readings for each standard, control, and samples and subtract the average zero standard
optical density. Create a standard curve with Anti-COL3 concentration on the y-axis and absorbance on the x-axis.
Draw a best fit curve through the points and it can be determined by regression analysis. If samples have been
diluted, the concentration read from the standard curve must be multiplied by the dilution factorr.
[ TYPICAL DATA ]
In order to make the calculation easier, we plot the O.D. value of the standard (X-axis) against the known
concentration of the standard (Y-axis), although concentration is the independent variable and O.D. value is the
dependent variable. However, the O.D. values of the standard curve may vary according to the conditions of
assay performance (e.g. operator, pipetting technique, washing technique or temperature effects), plotting log of
the data to establish standard curve for each test is recommended. Typical standard curve below is provided for
reference only.
Typical Standard Curve for Anti-COL3, Human ELISA.
[ DETECTION RANGE ]
3.12-200ng/mL. The standard curve concentrations used for the ELISA’s were 200ng/mL, 100ng/mL, 50ng/mL,
25ng/mL, 12.5ng/mL, 6.25ng/mL, 3.12ng/mL.
[ SENSITIVITY ]
The minimum detectable dose of Anti-COL3 is typically less than 1.25ng/mL.
The sensitivity of this assay, or Lower Limit of Detection (LLD) was defined as the lowest protein concentration
that could be differentiated from zero. It was determined by adding two standard deviations to the mean optical
density value of twenty zero standard replicates and calculating the corresponding concentration.
[ SPECIFICITY ]
This assay has high sensitivity and excellent specificity for detection of Anti-COL3.
No significant cross-reactivity or interference between Anti-COL3 and analogues was observed.
Note:
Limited by current skills and knowledge, it is impossible for us to complete the cross- reactivity detection between
Anti-COL3 and all the analogues, therefore, cross reaction may still exist.
[ RECOVERY ]
Matrices listed below were spiked with certain level of recombinant Anti-COL3 and the recovery rates were
calculated by comparing the measured value to the expected amount of Anti-COL3 in samples.
Matrix Recovery range (%) Average(%)
serum(n=5) 80-103 92
EDTA plasma(n=5) 91-105 101
heparin plasma(n=5) 84-96 90
[ LINEARITY ]
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Anti-COL3 and
their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the
expected.
Sample 1：2 1：4 1：8 1：16
serum(n=5) 95-105% 90-101% 78-91% 85-94%
EDTA plasma(n=5) 90-99% 93-107% 80-92% 79-104%
heparin plasma(n=5) 83-103% 81-99% 88-104% 92-109%
[ PRECISION ]
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Anti-COL3 were
tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Anti-COL3 were
tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
[ STABILITY ]
The stability of ELISA kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within
the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room
temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the
whole assay is performed by the same operator from the beginning to the end.
[ ASSAY PROCEDURE SUMMARY ]
1. Prepare all reagents, samples and standards;
2. Add 100μL standard or sample to each well. Incubate 1 hour at 37oC;
3. Aspirate and add 100μL prepared Detection Reagent A. Incubate 1 hour at 37oC;
4. Aspirate and wash 5 times;
5. Add 90μL Substrate Solution. Incubate 10-20 minutes at 37oC;
6. Add 50μL Stop Solution. Read at 450nm immediately.
[ IMPORTANT NOTE ]
1. Limited by the current condition and scientific technology, we can't completely conduct the comprehensive
identification and analysis on the raw material provided by suppliers. So there might be some qualitative and
technical risks to use the kit.
2. The final experimental results will be closely related to validity of the products, operation skills of the end
users and the experimental environments. Please make sure that sufficient samples are available.
3. Kits from different batches may be a little different in detection range, sensitivity and color developing time.
Please perform the experiment exactly according to the instruction attached in kit while electronic ones from
our website is only for information.
4. Do not mix or substitute reagents from one kit lot to another. Use only the reagents supplied by manufacturer.
5. Protect all reagents from strong light during storage and incubation. All the bottle caps of reagents should be
covered tightly to prevent the evaporation and contamination of microorganism.
6. There may be some foggy substance in the wells when the plate is opened at the first time. It will not have
any effect on the final assay results. Do not remove microtiter plate from the storage bag until needed.
7. Wrong operations during the reagents preparation and loading, as well as incorrect parameter setting for the
plate reader may lead to incorrect results. A microplate plate reader with a bandwidth of 10nm or less and an
optical density range of 0-3 O.D. or greater at 450 ± 10nm wavelength is acceptable for use in absorbance
measurement. Please read the instruction carefully and adjust the instrument prior to the experiment.
8. Even the same operator might get different results in two separate experiments. In order to get better
reproducible results, the operation of every step in the assay should be controlled. Furthermore, a
preliminary experiment before assay for each batch is recommended.
9. Each kit has been strictly passed Q.C test. However, results from end users might be inconsistent with our
in-house data due to some unexpected transportation conditions or different lab equipments. Intra-assay
variance among kits from different batches might arise from above factors, too.
10. Kits from different manufacturers with the same item might produce different results, since we haven’t
compared our products with other manufacturers.
11. The instruction manual also suits for the kit of 48T, but all reagents of 48T kit are reduced by half.
12. The kit is designed for research use only, we will not be responsible for any issue if the kit was used in
clinical diagnostic or any other procedures.
[ PRECAUTION ]
The Stop Solution suggested for use with this kit is an acid solution. Wear eye, hand, face, and clothing protection
when using this material.
[ TROUBLE SHOOTING ]
Problem Possible Source Correction Action
Poor Improper standard curve preparation Ensure accurate operation of the dilution
Standard Incomplete washing and aspiration Adequate washing and adequate aspiration
Curve Inaccurate Pipetting Check and Calibrate pipettes
Incomplete washing of wells Ensure sufficient washing
Poor Inadequate mixing and aspiration reagents Adequate aspiration and mixing reagents
Precision Reused pipette tips, containers and sealers Change and use new pipette tips, containers and sealers
Inaccurate Pipetting Check and Calibrate pipettes
Inadequate reagent volumes added to wells Calibrate pipettes and Add adequate reagents
Incorrect incubation times Ensure sufficient incubation times
Low
Incorrect incubation temperature Reagents balanced to room temperature
O.D
Conjugate or substrate reagent failure Mix conjugate & substrate, color should develop immediately
Values
No stop solution added Follow the assay protocol in the kit manual
Read beyond suggested reading time Read within the time recommended in the manual
Improper Sample Storage Store the sample properly and use the fresh sample
Sample
Improper sample collection and preparation Take proper sample collection and preparation method
Values
Low quantity of analyte in samples Use new sample and repeat assay
