0% found this document useful (0 votes)
21 views1 page

Detailing Reference

The document provides specifications for minimum bolt rows, edge distances for standard round holes, and various gages for beams and channels. It includes details on maximum bolt rows, nominal hole dimensions, and minimum weld sizes based on material thickness. Additionally, it outlines requirements for slotted holes and cold bending radii for different steel thicknesses.

Uploaded by

anandh.rs14
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
21 views1 page

Detailing Reference

The document provides specifications for minimum bolt rows, edge distances for standard round holes, and various gages for beams and channels. It includes details on maximum bolt rows, nominal hole dimensions, and minimum weld sizes based on material thickness. Additionally, it outlines requirements for slotted holes and cold bending radii for different steel thicknesses.

Uploaded by

anandh.rs14
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Minimum Bolt Rows Column Web Gages Minimum Edge Distance for Standard Round Holes

W6 1 Nominal Depth Gage Bolt Diameter 1/2" 5/8" 3/4" 7/8" 1" 1 1/8" 1 1/4" Over 1 1/4"
W8, W10, W12 2 W6 * 2 1/2" Sheared Edge 7/8" 1 1/8" 1 1/4" 1 1/2" * 1 3/4" * 2" 2 1/4" 1 3/4 x Bolt Diameter
W14, W16, W18 3 W8 * 4" Rolled or Gas Cut Edge 3/4" 7/8" 1" 1 1/8" 1 1/4" 1 1/2" 1 5/8" 1 1/4 x Bolt Diameter
W21, W24 4 W10 4" * These may be 1 1/4" at the ends of beam connection angles.
W27, W30 5 W12 and Larger 5 1/2" All edges that are rolled or gas cut may be reduced by 1/8" when the hole is at a point where stress does
W33, W36 6 * Flange holes must be staggered not exceed 25% of the maximum allowed stress.
from the web holes
Maximum Bolt Rows @ 3" Spacing Usual Gages for Angles
W6 1 Usual Gages for Channels Leg 8" 7" 6" 5" 4" 3 1/2" 3" 2 1/2" 2" 1 3/4" 1 1/2" 1 3/8" 1 1/4" 1"
W8, W10 2 Channel Size Usual Gage g 4 1/2" 4" 3 1/2" 3" 2 1/2" 2" 1 3/4" 1 3/8" 1 1/8" 1" 7/8" 7/8" 3/4" 5/8"
W12, W14 3 C15x50 2 1/4" g1 3" 2 1/2" 2 1/4" 2"
2
W16 4 C15x40 2" g 3" 3" 2 1/2" 1 3/4"
W18 5 C15x33.9 2"
W21 6 C12x30 1 3/4" Nominal Hole Dimensions
W24 7 C12x25 1 3/4" Hole Dimensions
W27 8 C12x20.7 1 3/4" Bolt Diameter Short-Slot Long-Slot
Standard Diameter Oversized Diameter
W30 9 C10x30 1 3/4" (Width x Length) (Width x Length)
W33, W36 10 C10x25 1 3/4" 1/2" 9/16" 5/8" 9/16" x 11/16" 9/16" x 1 1/4"
C10x20 1 1/2" 5/8" 11/16" 13/16" 11/16" x 7/8" 11/16" x 1 9/16"
Anchor Bolt Hole Oversize C10x15.3 1 1/2" 3/4" 13/16" 15/16" 13/16" x 1" 13/16" x 1 7/8"
3/4" Diameter 9/16" C9x20 1 1/2" 7/8" 15/16" 1 1/16" 15/16" x 1 1/8" 15/16" x 2 3/16"
7/8" Diameter 11/16" C9x15 1 3/8" 1" 1 1/16" 1 1/4" 1 1/16" x 1 5/16" 1 1/16" x 2 1/2"
1" to 1 1/2" Diameter 13/16" C9x13.4 1 3/8" 1 1/8" and Larger Diameter + 1/16" Diameter + 5/16" (d+1/16") x (d+3/8") (d+1/16) x (dx2.5)
1 3/4" Diameter 1" C8x18.75 1 1/2"
2" to 2 1/2" Diameter 1 1/4" C8x13.75 1 3/8" Minimum Radius for Cold Bending
C8x11.5 1 3/8" Thickness
ASTM Designation
AWS/AISC Minimum Weld Size C7x14.75 1 1/4" Up to 1/4" Over 1/4" to 1/2" Over 1/2" to 1" Over 1" to 1 1/2" Over 1 1/2" to 2"
Thinner Part Weld Size C7x12.25 1 1/4" A36 1 1/2 x Thickness 1 1/2 x Thickness 2 x Thickness 3 x Thickness 4 x Thickness
To 1/4" Inclusive 1/8" C7x9.8 1 1/4" A572-50 2 1/2 x Thickness 2 1/2 x Thickness 4 x Thickness -a -a
Over 1/4" to 1/2" 3/16" C6x13 1 3/8" a
It is recommended that steel in this thickness range be bent hot. Hot bending, however, may result in a decrease in the as-rolled mechanical
Over 1/2" to 3/4" 1/4" C6x10.5 1 1/8"
properties.
Over 3/4" to 1 1/2" 5/16" C6x8.2 1 1/8"
Over 1 1/2" to 2 1/4" 3/8" C5x9 1 1/8"
Over 2 1/4" to 6" 1/2" C5x6.7 - Values of Edge Distance Increment Increase
Over 6" 5/8" C4x7.25 1" Slotted Holes
Nominal Diameter of
C4x5.4 - Oversized Holes Perpendicular to Edge
Fastener Parallel to Edge
C3x6 - Short Slots Long Slots
C3x5 - 7/8" and less 1/16" 1/8"
Usual Beam Gages C3x4.1 - 1" 1/8" 1/8" 3/4 d 0
Flange Width Gage 1 1/8" and greater 1/8" 3/16"
4" 2 1/4"
4 1/16" to 6" 2 3/4"
6 1/16" to 7 15/16" 3 1/2"
8" and up 5 1/2"

You might also like