Scribd
Upload
15 views2 pages

2copies Specific Instruction To The Candidate

The document outlines specific instructions for candidates undertaking the Electrical Installation and Maintenance NC II qualification, detailing the competencies required and the tools, equipment, and materials needed for the tasks. Candidates will be observed during a 6-hour practical demonstration and will be rated on their performance, followed by a questioning and feedback session. Clarifications can be sought from the observer as needed.

Uploaded by

Mark Joseph Mirasol Mabugay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
15 views2 pages

2copies Specific Instruction To The Candidate

The document outlines specific instructions for candidates undertaking the Electrical Installation and Maintenance NC II qualification, detailing the competencies required and the tools, equipment, and materials needed for the tasks. Candidates will be observed during a 6-hour practical demonstration and will be rated on their performance, followed by a questioning and feedback session. Clarifications can be sought from the observer as needed.

Uploaded by

Mark Joseph Mirasol Mabugay
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Specific Instruction for the Candidate

Qualification:

ELECTRICAL INSTALLATION AND MAINTENANCE NC II


Unit of Competency:
 Perform roughing-in activities, wiring and cabling works for
single-phase distribution, power, lighting and auxiliary
systems
 Install electrical protective devices for distribution, power,
lighting, auxiliary, lightning protection and grounding
systems
 Install wiring devices of floor and wall mounted outlets,
lighting fixtures/switches, and auxiliary outlets

General Instruction:
Given the necessary tools, materials and equipment you need to
perform the task within 6 hours. I will be observing you while you are
performing the tasks.

Specific Instruction:
I will be observing you while you are performing the tasks.

You will be rated using the rating sheet.

After your demonstration, I will ask you some questions related to your
demonstration, and you will have a written examination.

You may call me when there is a need for me to translate or explain


items for clarification

After the questioning portion, I will give feedback regarding your


performance

Any questions/clarifications? If there are no more questions you may


start now.
Tools: Equipment Materials:

 Spirit level  Electric drill  Safety goggles


 Hack saw  Portable grinder  RSC/IMC
 Pipe cutter  Multi-tester  Entrance cap
 Pipe reamer  Fire alarm  Locknut & bushing
 Pipe threader system  Ground Fault Current
 Pipe bender (5units detector, interrupting device
 Bolt cutter 1  (GFCI)
 Ball hammer control panel)  3/16’ x 1” Metal Screw
 Electrician Pliers  Motion sensors  Conduit strap/clamp
 Screwdrivers set  Security  Wiring boards, ¾ ft. x 4
 Box Wrench equipment ft. x 8 ft.
 Wire splicer Access  Floor outlet
 Wire stripper Control  Working gloves
 Electrician knife  CCTV (4  Safety shoes
 Tools holster cameras,  Hard hat
 Push-pull 0-5 1 DVR)  Wire AWG #12,
mtrs  Clamp-on meter (3.5mm2)
 Claw hammer  Insulation  Wire AWG
 Prick punch Resistance #14(2.0mm2)
 Heat gun 1200 Tester  Electrical tape
watts  Earth resistance  Wood screw ½” x 8
 Heavy-duty Tester  Receptacle surface
soldering iron  Labeling type
 Flat file smooth machine  Receptacle flush type
8”  Fire extinguisher  Incandescent bulb 50
 #16 G.I wire KGS ABC w/250V AC
 Whiteboard 4 x 8  LCD Projector  Convenient outlet c.o.
x  Laptop (grounding
¾ type,/flush
 Whiteboard 4 x 4 type) 2 gang w/
x plate and
 ¾ with movable cover
stand  PVC square box, 4 x 4
 Whiteboard  flexible conduit ½”, ¾
marker,  PVC conduit ½, ¾
assorted color  Junction box PVC
 Push pin  Utility box
 Pencil sharpener  Connectors PVC, ½
 Pencil with eraser  Connectors PVC, ¾
 Rags  Connectors RSC, ¾
 Cleaning agent  Elbow PVC ½
liquid  Elbow PVC ¾
 First aid kit  Elbow RSC ½
 Bond paper  Elbow RSC ¾
 Whiteboard  Panel board with 70
eraser magnetic amp main and 4
branch ckt.
 20 amps, 2 pcs.
 15 amps, 2 pcs.
 Switch (3 way with
plate and cover)
 Switch (single pole with
plate and cover)

You might also like