Code No: 201224 Time: 3 hours LB. Tech I Semester Regular Examinations, September- 2021 ENGINEERING DRAWING (Comm, to Mining, Agri. E, Phar. E) Max. Marks: 70 Dy 6 ») “Answer any five Questions one Question from Each Unit All Questions Carry Equal Marks UNTI The Directrix of a hyperbola is 65mm from its focus. Draw the curve if the eccentricity is 3/2. Draw a normal and a tangent at a point on the curve. 75 mm from the Focus, Construct a scale of 1:8 to show decimeters and centimeters and to read up to Im. Show a Jength of 7.6 dm on it. or Draw epicycloids if a circle of 40 mm diameter rolls outside another cirele of 120 mm diameter for one revolution Inscribe an ellipse in a parallelogram of sides 150 x 100 mm with an inclined angle of 120”, UN Dravy the projections of the following points, keeping the distance between the projectors as 25 mm on the same reference line: (@) Point ‘A’ on HP and 20 mm behind VP. Gil) Point ‘B’ 20 mm below HP and 30 mm behind VP. Draw the projections of a 60 mm Tong straight line, in the following positions, (@) Perpendicular to the HP, in the VP and its one end in the HP. (ii) Inclined at 45° to the VP, in the HIP and its one end in the VP. or A line AB. 80 mm long, makes an angle of 30" with the VP, and lies in a plane perpendicular to both the HP and VP. Its end A is in the HP, and the end B is in the VP. Draw its projections and show its traces UNIT-IL A semi-circular plane of diameter 70 rm has its straight edge on the HP and inclined at 45° to the VP. Draw the projection of the plane when its surface is ‘inlined at 30° to the HP. Or PQRS is a rhombus having diagonal PR = 60 mm and QS = 40 mm and they are perpendicular to each other. The plane of the rhombus is inclined with H.P. Such that its top view appears to be square. The top view of PR makes 30” with the ‘V.P. Draw its projections and determine inclination of the plane with the HLP. UNIT-IV Draw the projections of a pentagonal prism of base side 25 mm and axis length St) mm rests on the HP on one of its rectangular faces. The axis is inclined at 45° to the VP. or A cone with 50 mm diameter and axis 65 mm has one of its generators in the VP and inelined at 45° to the HP. Draw the projections of the cone 1of2 «™) cM) «™) OM) (MD (@M) 4M) (14M (lam aM) 4m)Code No: R201224 UNITY 9, Figure shows two views of an object. Draw the isometric view of the object. All (14N1) dimensions in the figure are in mm. FRONT VIEW or 10. Draw the three views of the part shown in the figure below. All dimensions are in (14M) mm,Code No: R201224 TB. Tech I Semester Regular/Supplementary Examinations, AUGUST- 2022 ‘Time: 3 hours ENGINEERING DRAWING (Com. to Mining, Agri. E, Pharm E) Max. Marks: 70 a) 6) a) 6) ‘Answer any five Questions one Question from Each Unit All Questions Carry Equal Marks UNIT Draw an ellipse having the major axis of 100 mm and the minor axis of 60 ‘The actual length of 500 m is represented by a line of 15 em on a drawing. Construct a vernier seale to read up to 600 m, Mark on ita length of 568 m, Or Draw a hyperbola when the distance between its focus and ditectrix is 50 mm and eccentricity is 3/2. Also draw the tangent and normal at a point 25 ‘mm from the directrix. UNIT-IT ‘The TV of a line CD measures 80 mm and makes an angle 55° with XY. End isin VP and the HT of line is 25 mm above XY. The line is inclined at 30° to the HP. Draw the projections of line CD, Determine its true length, (rue §nclination with VP and VT. Or ‘Draw the projections of the following points on @ common reference line, (a) P35 mm behind the VP and 20 mm below the HP. (b) Q.40 mm infront the VP and 30 mm above the HP. (c) R50 mm behind the VP and 15 mm above the HP. (a) S 40 mm below the HP and in the VP. (c) T 30 mm infront of the VP and 50 mm below the HP. Line AB is $5 mm long and it is 25° & 45° inclined to HP & VP respectively. End A is 15 mm ahove HP and 15 mm in front of VP. Draw projections. Ling is in Ist quadrant UNIT-IIE Semi-cireular plate of 80 mm diameter has its straight edge on VP and ‘inclined at 30° to HP, while the surface of the plate is inclined at 45° to VP. Draw the projections of the plate or A regular hexagon of 40mm has a corner in the HP. Its surface is inclined at 45" to the HP and the top view of the diagonal through the corner which is in the HP makes an angle of 60° with the VP. Draw its projeetions.9 UNIT-IV Draw the projections of a cone, base 75 mm diameter and axis 100 mm long, lying on the ground on one of its generators with the axis parallel to the VP. Assuming the cone to be resting on its base on the ground, dravy its projections. Or tof? OM) aM) (4M) 4p cM) «My amy 4M) (lam)Code No: R201224 8 ‘Draw the projections of hexagonal pyramid of base 25 mm and height 60 (14ND) rmm long, has an edge of its base on the ground. Its axis is inclined at 30° to the ground and parallel to the V.P. Draw its projections. 9 Draw the isometric view of given casting as shown in figure below. All (4M) dimensions are in mam, Or 10 Draw the a) Front view b) Side view from the left c) Top view as shown in (14M) figure below. all dimensions are in mm,Code No: R201224 Time: 3 hours 1B. Tech II Semester Regular/Supplementary Examinations, July/August-2023, ENGINEERING DRAWING (Common to Mining, Agri. E, Phar.) ‘Max. Marks: 70 b) ‘Answer any five Questions one Question from Each Unit All Questions Carry Equal Marks UNIT-I ‘A fixed point F is 7.5 em from a fixed straight line. Draw the locus of a point P moving in such a way that its distance from the fixed straight Tine is 2/3 times its distance from F. Name the curve, Draw normal and tangent at a point 6 cm from F. (OR) ‘Two fixed points A and B are 100 mn apart. Trace the complete path of @ point P moving (in the same plane as that of A and B) in such a way that the sum of its distances from A and B is always cqual to 125 mm, Name the curve, Draw another curve parallel to and 25 mm away from this curve. UNIT-IT A 100mm long line is parallel to and 40mm above the H.P. Its two ends are 25mm and SOmm in front of the V.P. respectively. Draw it projections and find its inelination with the VP. Draw the projections of a line AB, 90 mm long, its midpoint M being 50 mm above the HP and 40 mm in front of the VP. The end A is 20 rm above the HP and 10 mm in front of the VP. (OR) A line AB of 70mm long has its end A at 10mm above LLP. and 15mm in front of VP Its front view and top view measure 5mm and 60mm respectively. Draw the Projections of the line and determine its inclinations with H.P, and V.P. UNIT-IT A rectangle ABCD 60) mm x 40 mm is parallel to HP with one of its sides inelined at 30” to VP and the end of the side near to VP is 15 mm in front of the VP and 30 mm above the HP. Draw its projections (OR) A regular pentagon of 30mm sides is resting on HP on one of its side while its opposite vertex is Mmm above HP. Draw the projections whea the side in HP is 30” inclined to VP UNIT-IV Draw the projections of 2 hexagonal prism of base 25mm and axis 60mm Tong, when it is resting on one of its corners of the base on H.P. The axis of the solid is inclined at 45° to HP. A cube of 50mm long edges is resting on the H.P. with its Vertical faces equally inelined to the V.P, Draw its projections. (OR) A square pyramid, base 40mm side and axis 90mm Tong, has a trigngular face on the ground and the vertical plane containing the axis makes an angle of 45° with the V.P. Draw its projections Lof2 [4M [14M] (7™] i) (4M [14M] [14M (7™] i™) [14M]Code No: R201224 R20 ‘UNIT-V 9. ‘Sketch the pictorial view for the below figure irom the given orthographic views. [14M] 21 KB 0 Ao, as (OR) 10. Draw the elevation, plan, left and right views of the part shown in the figure below. [14M] (ATI dimensions are in mn). lof2