1.

DC Circuits(Chap1 &2)
1. Use KVL, nodal, mesh and Thevenin equivalent circuit analysis techniques to determine i1
and i2 for Fig1.( Ans :i 1=−0.625 A , i2=−1.75 A)

Fig1 Fig2
2. Use KVL, nodal, mesh and Thevenin equivalent circuit analysis techniques to determine v
in Fig2. In addition, if the 5 Ω resistor can be replaced by another suitable resistor, then
find its value if it is required to receive maximum power from the source.
3. Use KVL, nodal, mesh and Thevenin equivalent circuit analysis techniques to determine i
for Fig3.

Fig3

2.Transient Circuits(Chap4)

Fig4 Fig5

4. The switch in the circuit given in Fig4 above has been closed for a long time. At t = 0, the
switch is opened. Calculate i(t) for t > 0.
5. In the circuit shown in Fig5, the switch opens at t = 0. Find i 1 (t) for t >0.

Electrical and Electronics Dept Page 1

 Fig6 Fig7
6. The switch in the circuit Fig6 has been closed for a long time, and it is opened at t = 0.
Find v (t) for t ≥ 0. Calculate the initial energy stored in the capacitor
7. Refer to the circuit in Fig7. Let v C ( 0 )=30 V . Determine v C , v x ∧i 0 for t ≥ 0.
3. Steady State AC Circuit Analysis (Chap3)
3.1 Sinusoids and Phasors
8. Evaluate the following complex numbers:

9. Transform these sinusoids to phasors:

( a ) v (t)=−4 sin ⁡(30 t +50 0) ( b ) i (t )=6 cos ⁡(50 t−400 )
( c ) i(t)=8 co s ( 5 t−30 0 )+ 6 cos 5 t
10. Given v 1=20 sin ( ωt +600 ) ∧v 2=60 cos ( ωt−10 0 ), determine the phase angle between the two
sinusoids and which one lags the other.
11. Using phasors, find the simplified form of:
( a ) 3 cos ⁡(20 t+ 10 0)−5 cos ⁡(20t−3 0 0) ( b ) 40 sin50 t +30 cos ⁡(50 t−450 )
( c ) 20 sin 400 t+10 cos ( 400 t +600 ) −5 sin ⁡(400t−200)
12. Obtain the sinusoids corresponding to each of the following phasors:
13. ( a ) V 1=60¿ 15 0 , ω=1 ( b ) V 2=6+ j 8 , ω=40 ( c ) I 1=2e− j 0.5 π ,ω=377
3.2 Equivalent Impedances and Admittances( AC
Circuits)
14. At ω=50 rad / s, determine Z ¿ for each of the circuits in Fig8.

(a) (b)
Electrical and Electronics Dept Page 2
 Fig8
15.Determine I ∧ZT for the circuit in Fig9.

Fig9
16. At ω=10 rad / s, find the input admittance of each of the circuits in Fig10.
3

(a) (b)

(c)
Fig10

3.3 Voltages and currents in AC Circuits

17.Find i (t )∧v (t) in the circuit of Fig.11.
18.Calculate i 1 ( t )∧i 2 ( t )in the circuit of Fig.12, if the source frequency is 60 Hz

Fig.11 Fig.12

Electrical and Electronics Dept Page 3

 19.Find current i 0 in the network of Fig.13.

Fig.13

3.4 AC power Analysis(single phase)

20.In the circuit of Fig.14, calculate the average power absorbed by the resistor and
inductor. Find the average power supplied by the voltage source.

Fig.14 Fig.15
21.Determine the power generated by each source and the average power absorbed by each
passive element in the circuit of Fig.15.
22.Determine the load impedance Z Lthat maximizes the average power drawn from the
circuit of Fig.16. What is the maximum average power?

Fig.16 Fig.17
23.In Fig.17, the resistor R L is adjusted until it absorbs the maximum average power.
Calculate R L and the maximum average power absorbed by it.
24.The waveform shown in Fig.18(a) is a half-wave rectified sine wave. Find the rms value
and the amount of average power dissipated in a 10 Ω resistor.
25.Determine the rms value of the waveform in Fig.18(b). Calculate the average power
dissipated in a 6 Ω resistor.
26.Find the rms value of the current waveform of Fig.18(c). If the current flows through a 9 Ω
resistor, calculate the average power absorbed by the resistor.

Electrical and Electronics Dept Page 4

 (a) (b)

(c)
Fig.18

27.The voltage across a load is v ( t )=60 cos ( ωt−100 ) V and the current through the element in
the direction of the voltage drop is i (t )=1.5 cos ( ωt +500 ) A. Find:
(a) the complex and apparent powers, (b) the real and reactive powers, and (c) the power
factor and the load impedance.
28.For a load, V rms =110 ¿ 85 0 V , I rms =0.4 ¿ 150 A . Determine:
(a) the complex and apparent powers, (b) the real and reactive powers, and
(c) the power factor and the load impedance.
29.A load Z draws 12 kVA at a power factor of 0.856 lagging from a 120-V rms sinusoidal
source. Calculate: (a) the average and reactive powers delivered to the load, (b) the peak
current, and (c) the load impedance.
4. Three Phase Systems(Chap5)
30.For the Y −Y circuit of Fig. 19, find the line currents, the line voltages, and the load
voltages

Electrical and Electronics Dept Page 5

 Fig. 19 Fig. 20
31.Obtain the line currents in the three-phase circuit of Fig. 20 above. (Y −Y )

Fig. 21 Fig. 22
32.If V an=440 ¿ 60 V in the network of Fig. 21, find the load phase currents I AB , I BC ∧I CA .
0

(Y −Δ type)
33.A balanced abc-sequence Y-connected source with V an=100 ¿ 100 V is connected to a
Δ−connected balanced load ( 8+ j 4 ) Ω per phase . Calculate the phase and line currents. Two
ways(direct or after converting to Y-Y).
34.For the Δ−Δ circuit of Fig. 22, calculate the phase and line currents.

Electrical and Electronics Dept Page 6

 Fig. 23

35.For the unbalanced circuit in Fig. 23 , find: (a) the line currents, (b) the total complex
power absorbed by the load, and (c) the total complex power supplied by the source

Electrical and Electronics Dept Page 7