Scribd
Upload
11 views1 page

Ftam16-1053 Threaded TW Only

The document outlines specifications for thermowell construction, including internal hydrostatic pressure testing at 3000 PSI, material requirements, and dimensional tolerances. It also details documentation requirements such as wake frequency analysis and material test reports, which must be approved before fabrication. Various options for thermowell design, materials, and dimensions are provided, along with specific tolerances for manufacturing.

Uploaded by

steelman.ryan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
11 views1 page

Ftam16-1053 Threaded TW Only

The document outlines specifications for thermowell construction, including internal hydrostatic pressure testing at 3000 PSI, material requirements, and dimensional tolerances. It also details documentation requirements such as wake frequency analysis and material test reports, which must be approved before fabrication. Various options for thermowell design, materials, and dimensions are provided, along with specific tolerances for manufacturing.

Uploaded by

steelman.ryan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

THERMOWELL NOTES:

1A. INTERNAL HYDROSTATIC PRESSURE TEST @ 3000 PSI.


1B. MANUFACTURE'S STANDARD TOLERANCES APPLY, UNLESS NOTED OTHERWISE.
1C. THERMOWELL TO BE STAMPED WITH 'TW' TAG#, MATERIAL, SERIAL#, MANUFACTURER NAME,
AND 'U' DIMENSION.
1D. ALL DIMENSIONS TO BE IN INCHES.
1E. THERMOWELL SHANK TO BE 4-16 Ra SURFACE FINISH.
1F. THERMOWELL SHANK SHALL BE SINGLE-PIECE CONSTRUCTION, 1-3/8" OD HEX BAR STOCK
3
FOR 1" NPT PROCESS CONNECTION. 4" 'T' 1" 'U'

DOCUMENTATION (UPON REQUEST):


2A. WAKE FREQUENCY ANALYSIS (VELOCITY/VIBRATION CALCULATIONS) PER ASME PTC 19.3-2010.
(A) ALL CALCULATION RESULTS AND DIMENSIONAL DRAWINGS SHALL BE APPROVED BY CITGO 'Q'
PRIOR TO START OF THERMOWELL FABRICATION.
2B. MTRs (MILL TEST REPORT) FOR BAR STOCK.
2C. INTERNAL HYDROSTATIC PRESSURE TEST REPORT.
2D. POSITIVE MATERIAL IDENTIFICATION TEST REPORT. 'V'

.281" BORE

THERMOWELL (OPTIONS): 'D'=1-3/8"


1" PROCESS CONNECTION
CODE DESIGN
T TAPERED
S STRAIGHT

CODE THERMOWELL MATERIAL


1 316SS 'A'= 'U' + 'T' + 134" - 't' 't'=41"
2 304SS
3 MONEL 400
4 INCONEL 600
5 HASTELLOY C-276
OTHER (PLEASE SPECIFY)

FTAM16-1053
CODE 'U' (INSERTION LENGTH)
PLEASE SPECIFY
THERMOWELL THERMOWELL 'T' 'U' 'Q' 'V'
DESIGN MATERIAL LAGGING INSERTION ROOT TIP
EXTENSION LENGTH DIAMETER DIAMETER
CODE 'T' (LAGGING EXTENSION)
PLEASE SPECIFY

CODE 'Q' (ROOT DIAMETER)


PLEASE SPECIFY

CODE 'V' (TIP DIAMETER)


PLEASE SPECIFY TOLERANCES
REVISIONS (UNLESS STATED OTHERWISE)

DIMENSIONS
REV DESCRIPTION DATE REV. BY APPROVED 'D', 'Q', 'V': ± 0.01"
(IF APPLICABLE TO DRAWING)
DIMENSIONS
'C', 'A', 'U', 'H', 't': ± 1/16"
5700 HARTSDALE DRIVE, HOUSTON, TX 77036 (713) 780-8600
(IF APPLICABLE TO DRAWING)
ALL OTHER DIMENSIONS: DATE: SCALE: DRAWN BY: APPROVED BY: REV
.X: ± .1" 08/10/16 NONE KER MEV 0
.XX: ± .01"
.XXX: ± .005"
FRACTIONS: ±1/16" SHEET: 1 OF 1
PROPRIETARY DRAWING CITGO STANDARD SCREW-IN THERMOWELL ASSEMBLY
ANGLES: ±5°
This document is the property of Daily Thermetrics Corporation and Daily Instruments DWG NO.
Corporation, and is delivered on the express condition that it and the technical data and RADII: ±1/16"
information embodied herein are not to be used, disclosed, or reproduced in whole or in CHAMFERS: ±1/16"
part, for any purpose without the express written approval of Daily Thermetrics TIR: ±10% WALL THICKNESS
FTAM16-1053
Corporation or Daily Instruments Corporation.
CONCENTRICITY: ± .010"

You might also like