Scribd
Upload
2 views

DS.Z.04

This document outlines the product standard for Dowel Screws, including required dimensions, mechanical properties, and chemical characteristics. It specifies that national or international standards must be adhered to and lists various sizes and specifications for the screws. Additionally, it details the material properties, finish requirements, and tolerances for length and thread length.

Uploaded by

buttress0716
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2 views

DS.Z.04

This document outlines the product standard for Dowel Screws, including required dimensions, mechanical properties, and chemical characteristics. It specifies that national or international standards must be adhered to and lists various sizes and specifications for the screws. Additionally, it details the material properties, finish requirements, and tolerances for length and thread length.

Uploaded by

buttress0716
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2 Fastenal Product Standard REV-04

Date: March 25, 2021 DS.Z

Dowel Screw, Zinc


This product standard contains the required dimensional, mechanical, performance, and chemical characteristics of the products shown
in this purchase order (as applicable to the product). Unless specified below, current revisions of national or international standards
shall be applicable as of the date of Fastenal’s purchase order and must be adhered to in their entirety. If the order received does not
meet these requirements, corrective action may be issued which could jeopardize your status as an approved supplier to Fastenal.

Diameter & A B
Overall
Thread Thread Collar
Length
Pitch Lengths Lengths
3/4 3/8 -
#6-18
1 3/8 1/4
1 1/2 -
#8-15 1 1/4 5/8 -
1 1/2 5/8 1/4
1 1/2 -
1 1/4 1/2 1/4
1 1/2 3/4 -
1 3/4 3/4 1/4
3/16-11
2 7/8 1/4
2 1/4 7/8 1/2
2 1/2 1 1/8 1/4
3 1 3/8 1/4
1 1/2 3/4 -
1 3/4 3/4 1/4
2 7/8 1/4
1/4-10
2 1/2 1 1/8 1/4
3 1 3/8 1/4
3 1/2 1 5/8 1/4
1 1/2 3/4 -
1 3/4 3/4 1/4
2 7/8 1/4
2 1/2 1 1/8 1/4
3 1 3/8 1/4
5/16-9
3 1/2 1 5/8 1/4
4 1 5/8 3/4
4 1/2 2 1/4 -
5 2 1/4 1/2
6 2 1/4 1 1/2

RECORD OF REVISION CHANGES TO THIS DOCUMENT ARE LOCATED ON THE


LAST PAGE
Page 2 of 2 Fastenal Product Standard REV-04

Date: March 25, 2021 DS.Z

Diameter & A B
Overall
Thread Thread Collar
Length
Pitch Lengths Lengths
2 7/8 1/4
2 1/2 1 1/8 1/4
3 1 3/8 1/4
3 1/2 1 5/8 1/4
3/8-7 4 1 5/8 3/4
4 1/2 2 1/4 -
5 2 1/4 1/2
6 2 1/4 1 1/2
8 3 2
4 2 -
5 2 1
1/2-6
6 3 -
8 3 2

Length Length Tolerance


6" ≤ L ± 1/16"
6" > L ± 1/8"
Thread Length Tolerance: ± 0.06"

Specification Requirements:

• Dimensions: See table Above


• Thread Requirements: Lag Screw Threads
• Material &
Mechanical Properties: Low Carbon Steel.
Core hardness: HRB 70 to 100.
Tensile strength: 60,000 psi minimum.
• Finish: Fe/Zn 3AN per ASTM F1941/F1941M.

Revision Level Changes to this Document

Revision Revision
Document Name Rationale for Revision
Level Date
DS.Z 04 3/25/2021 Updated format.

The rationale above may not include all of the changes within each revision. A complete
review of the Fastenal Product Standard is required.

You might also like