EN

OPERATING
INSTRUCTIONS
DISHWASHER
 Contents

Front panel ................................................................................................ 2

Safety instructions ..................................................................................... 3
Before washing for the first time ............................................................... 4
Loading the dishwasher ............................................................................ 5
Using the dishwasher ................................................................................ 6
Settings ..................................................................................................... 9
Care and cleaning ..................................................................................... 11
Troubleshooting ........................................................................................ 13
Installation ................................................................................................. 16
Service ...................................................................................................... 19
Information for test institute .......................................................................20
Technical information ................................................................................ 24

Front panel

1 2 3 4 5 6 7 8 9 10 11 12 13 14

1 Main power switch 8 SpeedWash

2 Programme selector 9 Extra dry
3 Daily wash 10 Half load
4 Intensive wash 11 Delayed start
5 Eco wash 12 Display
6 Quick wash 13 Rinse aid indicator
7 Rinse 14 Salt indicator

2
Safety instructions

General Winter storage/transport

• Read the operating instructions and keep them • Store the dishwasher where the temperature remains
in a safe place! above freezing.
• Never use the dishwasher for any purpose other • Avoid long transport distances in very cold weather.
than that specified in these operating instructions. • Transport the dishwasher upright or laying on its back.
• Do not load the dishwasher door or dishwasher Overflow guard function
baskets with anything other than dishes. The overflow protection starts pumping out the machine
• Never leave the dishwasher door open as and turns off the water supply if the water level in the
someone may trip on it. dishwasher exceeds the normal level. If the overflow
• Use only dishwasher detergent! protection is triggered, turn off the water supply and call the
service department.
• This machine can be used by children aged 8
and upwards, and by people with reduced Packing material
physical capacity, mental ability, memory loss or The packaging protects the product during transport. The
lacking experience and knowledge. These packaging material is recyclable. Separate the different
individuals must be supervised when using the packaging materials to help reduce raw material use and
machine or have instructions on how to use the waste. Your dealer can take the packaging for recycling or
machine and understand the risks that can occur. direct you to the nearest recycling centre. The packaging
is comprised of:
Cleaning of the machine must not be carried out
by children without supervision. • Corrugated cardboard made from up to 100% recycled
• Children must be watched to ensure they do not material.
play with the dishwasher. • Expanded polystyrene (EPS) with no added chlorine or
fluorine.
• Damaged mains cables must only be replaced
• Supports made from untreated wood.
by a qualified electrician.
• Protective plastic made from polyethylene (PE).
• Only use the dishwasher in household-type
environments for dishwashing household dishes. Disposal
All other use is prohibited. • When the dishwasher has reached the end of its service
• Never place dishes with solvent residues in the life and is to be disposed of, it should immediately be
dishwasher due to the risk of explosion. Nor may made unusable. Pull out the power cable and cut it as
short as possible.
dishes that contain ash, wax or lubricants be
• The dishwasher is manufactured and labelled for
washed in the dishwasher.
recycling.
• Contact your local authority for information about where
WARNING! and how your dishwasher should be correctly recycled.
Knives and other pointed items must be placed
with the points down in the cutlery basket or
horizontally in other baskets.

Installation
See the section Installation.

Child safety
• Always start the dishwasher immediately after adding
detergent.
• Keep children away from the dishwasher when the door
is open. Some detergent may remain inside!
• Do not allow children to use or play with the dishwasher.
Be especially vigilant when the door is open.

WARNING!
Children must be supervised – dishwasher detergent is
corrosive!

3
 Before washing for the first time

The water softener

In order to achieve good dishwashing results, the Refill salt indicator
dishwasher needs soft water (water with low mineral When the salt needs topping up, the above symbol lights
content). Hard water leaves a white coating on dishes and on the display.
the dishwasher.
When the salt runs out, unscrew the cap and fill the
Water hardness is specified using the following scales: The container with salt. Water is only needed the first time! Wipe
German water hardness scale (°dH) and the French water clean and tighten. Run a programme to ensure that any salt
hardness scale (°fH). A water supply with a water hardness in the dishwasher is rinsed away.
in excess of 6°dH (9°fH) must be softened. This is done
After topping up, it may take a while before the symbol goes
automatically with the aid of the built-in water softener. In
out.
order for the softener to function optimally, it must be
adjusted to the hardness of the water supply.
Top up with rinse aid
Contact the local waterworks to check the water hardness Drying is faster and a better result is achieved if you use
in your area. rinse aid. You will also achieve a better dishwashing result
with clear and spotless dishes.
Adjusting the water softener
1 Open the rinse aid compartment lid.
Chapter Settings on page 9 describes how to adjust the
water softener. 2 Carefully top up with rinse aid. Only add rinse aid to the
level marked max.
Fill up the salt 3 Wipe up any splashes of rinse aid around the
Before you begin using a dishwasher with a water softener, compartment.
you must fill the salt compartment with salt for the water 4 Close the lid firmly.
supply to be softened automatically. Use large grain salt or
special dishwasher salt. Press to open

WARNING!
In order to avoid rust stains a dishwashing programme
must be started immediately after adding salt.

Never pour dishwasher detergent into the salt

compartment. This destroys the water softener!

Do as follows the first time:

1 Unscrew the lid as illustrated. Refill rinse aid indicator
When the rinse aid needs topping up, the above symbol
2 Place the funnel supplied with the dishwasher in the salt
lights on the display.
compartment top-up hole. First, pour in about 1 l of
water. After topping up, it may take a while before the symbol goes
3 Then add salt, a maximum of 1.5 kg, until the out.
compartment is full.
4 Wipe up any excess salt so that the lid can be screwed
Setting the rinse aid dosage
on firmly. The section Settings describes how to set the rinse aid
dosage. Rinse aid dispensing can be set from 0 (Off) to 5
5 Run a programme to ensure that any salt in the
(High dose). (Factory settings: 5)
dishwasher is rinsed away.
Decrease the rinse aid dosage:
• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the rinse
aid can be diluted 50:50 with water.

Salt compartment lid

4
Loading the dishwasher

Energy-efficient dishwashing Raising and lowering the upper basket

• Do not start the dishwasher until it is fully loaded to save 1 Pull out the upper basket. (The basket must be empty.)
energy. 2 Turn the basket catch outwards at the end of both
• Do not rinse under running water. Simply scrape off runners.
large food particles before loading the dishwasher. 3 Grip the upper basket with both hands, pull it out and
• Choose an environmentally-friendly detergent. Read the move the upper basket to its other position.
environmental declaration on the packaging! Turn back the basket catch at the end of both runners.
4
• If the dishes are only slightly dirty, you can select a
programme with a low temperature.
• Better drying results are achieved if you open the door
a little once the programme has ended. (If the
dishwasher is built-in the surrounding furnishings must
be resistant to any condensation.)

Fragile dishes
Some cookware is not dishwasher safe. This can be for
several reasons. Some materials cannot withstand strong
heat, others can be damaged by dishwashing detergent.

Exercise caution with, for example, handmade items, fragile Lower basket
decoration, crystal/glassware, silver, copper, tin, aluminium, Place plates, side plates, serving dishes, pots and cutlery
wood and plastic. Look for the "Dishwasher safe" marking. (in the cutlery basket) in the lower basket.
The dishwasher's baskets
The dishwasher is equipped with an upper basket and a
lower basket with a cutlery basket.

Upper basket
Place glasses, cups, bowls, side plates and saucers in the
upper basket. All dirty surfaces should face inwards and
downwards! Wine glasses are placed on the wine glass
shelf and knives are placed in the knife stand on the right
(if fitted).

Cutlery basket
Place cutlery with the handles facing down, except for
knives, and spread them out as much as possible. Ensure
that spoons do not stack inside each other.

Place the cutlery basket in the lower basket.

Points to consider
• All dirty surfaces should face inwards and downwards!
• Dishes should not be placed in or on each other.
• Angle dishes with hollows, such as cups, so that the
rinse water will run off. This is also important for plastic
items.
• Make sure small items cannot fall through the
dishwasher basket; place them in the cutlery basket.

NOTE!
Check that the spray arms can rotate freely.
5
 Using the dishwasher

Add detergent
The main power switch
Press to open
Press and hold the main power switch until the display turns
on. Also check that the water tap is on.

PROGRAMS - Choose programme

Choose a programme to suit the type of dishes and how
dirty they are.

Press the Programme selector one or more times until the

desired programme symbol is activated.
1 Prewash detergent compartment
2 Main wash detergent compartment
Daily wash
Detergent is added according to water hardness.
An effective programme for daily use for slightly dried
Follow the instructions on the detergent packaging. This leftovers. (This programme is not intended for burnt food,
dishwasher is fitted with a water softener, so use detergent such as on oven dishes.)
and rinse aid doses suitable for soft water.

Too much detergent can result in less effective dishwashing

and also entails greater environmental impact. Intensive wash
Programme for very dirty dishes, such as pans, casserole
The detergent compartment must be dry when adding
dishes and oven dishes. Also ideal for situations where
detergent. There is one compartment for the prewash and
demands on hygiene are especially high, such as when
one for the main wash. If powder or liquid dishwasher
dishwashing baby bottles and cutting boards. If these dishes
detergent is used, add a small amount of the detergent to
do not completely fill the dishwasher, you can add plates
the prewash compartment. Contact the detergent
and the like.
manufacturer if you have questions about the detergent.

NOTE!
Use only dishwasher detergent! Washing up liquid must Eco wash
not be used as the foam that forms prevents the This programme is intended for cleaning normally dirty
dishwasher from operating effectively. dishes and is the most effective programme in terms of
combined energy and water consumption.

Dishwasher tablets
Halve the tablet if it is difficult to close the dispenser lid. Quick wash
There is a risk that the detergent will not be released This programme is used for glasses and porcelain that is
properly if the lid is tight and will not open correctly. slightly dirty, such as coffee cups.

NOTE! In combination with SpeedWash, a shorter programme is

achieved (15 minutes).
Dishwasher tablets are not recommended for short
programmes (less than 75 minutes). Use powder or liquid
dishwasher detergent instead.
Rinse
Used to rinse dishes while you wait for the dishwasher to
3-in-1/All-in-one detergent become fully loaded.
Chapter Settings describes how to activate TAB (3-in-1/
All-in-one detergent). Note that salt must be put in the salt EXTRA - Selecting Options
compartment. If you are not satisfied with the dishwashing To select an option, press one of the option buttons until
or drying results, deactivate the setting TAB (3-in-1/ the option is activated. The available options vary between
All-in-one detergent) and top up with salt, detergent and programmes and some options cannot be combined
rinse aid. See Chapter Before washing for the first time. (available options glow dimly).

Read through the directions for these products carefully. If

anything is unclear, contact the detergent manufacturer. SpeedWash
This option shortens the programme time, but uses more
energy and water.

6
 Extra dry
Do you want to add more dishes?
A higher temperature in the final rinse improves the drying Open the door. The dishwasher stops automatically. Add
results if you activate this option. Energy consumption is the dishes and close the door. After a while, the dishwasher
slightly increased. continues the programme.

If the dishwasher is turned off due to a

Half load
This option adapts the dishwashing programme to a
power failure
half-filled dishwasher, using less energy and water. If the dishwashing programme was not finished, the
interrupted programme continues when power is restored.

Delayed start
NOTE!
When you select Delayed start the dishwasher will start
1-24 hours after you close the door. During drying, the programme is interrupted if the power
is cut or the door is open for more than 2 minutes.
1 Press the button once to activate Delayed start. Press
the button several times – or hold it in – to set the
desired number of hours.
How to get the best drying results
2 Close the door and the dishwasher counts down 1 hour
• Fully load the dishwasher.
at a time and starts after the selected delay.
• Angle dishes with hollows, such as cups, so that the
If you want to cancel the Delayed start option, open the door rinse water will run off. This is also important for plastic
and press and hold the main power switch until the display items.
turns off. • Top up with rinse aid or increase the rinse aid dosage
level.
Starting the dishwasher • Activate the Extra dry option.
Close the door to start the dishwasher. If the main power • Open the door a little once the programme has finished.
switch is on the dishwasher will start automatically when • Allow the dishes to cool before unloading the
the door is closed. dishwasher.

TIME - Time remaining Once the programme has finished

Once you have chosen a programme and options, the time Once the programme has finished, "End" appears on the
the programme took when last used is displayed. display.
Once you have started the dishwasher the display shows The dishwasher switches off automatically after the
the remaining programme time. The remaining time is programme ends. Shut off the water tap after each use.
updated after the water for the final rinse has been heated.
Unloading the dishwasher
This may differ somewhat from time to time depending on
Hot porcelain is more fragile. Leave the dishes to cool in
the temperature of the water supply, the amount of dishes,
the dishwasher before unloading them.
the ambient temperature and other factors.
Unload the lower basket first to avoid any water drops from
Front display
the upper basket falling onto the dishes in the lower basket.

Dishwashing Time remaining Drying

Stopping or changing a programme

If you want to change programme after starting the
dishwasher, open the door then press and hold the main
power switch until the display turns off. Add more detergent
if the lid of the detergent dispenser has opened. Then press
the main power switch, choose a new programme and close
the door.

7
8
Programme chart
PROGRAMS Detergent, EXTRA Prewashes Main wash Number of Final rinse Consumption values 1)

- Programme compartment - Options rinses

1/2 Dishwashing Energy Water cons.
(ml) time (approx. (L)
(approx. kWh)
hrs:min)
Daily wash --- / 25 2 60 °C 2 65 °C 1:45 1.2 16
Intensive wash 10 / 25 2 70 °C 2 70 °C 3:35 1.7 17
Eco wash 2) --- / 25 1 55 °C 2 62 °C 4:10 1.04 11.0
Quick wash --- / 10 35 °C 1 25 °C 0:20 0.2 10
Rinse --- / --- 1 --- °C 0:07 0.01 4
1) Consumption values vary depending on the temperature of the incoming water, room temperature, load size, selected additional functions and more.
2) This dishwashing programme is the standard cleaning cycle used to compile the energy labelling information. It is intended for washing normally dirty
dishes and is the most effective programme in terms of combined energy and water consumption.
Settings

Open the settings menu:

1. First, open the door. Turn off the machine. Press and hold the main power switch until the display
lights up.
2. Within 10 seconds:
+
- press the Programme selector and the option button for SpeedWash.
3. The display shows the settings menu (current setting and its currently set value).
(Exit the menu by browsing through the menu or pressing the main power switch.)
Navigate the settings menu:

Press to save the set value and continue to the

Press to browse between setting values. next setting.

Current setting.
Current setting value.

You can now adjust the following settings:

Settings Options

1. Rinse aid 1:00 - 1:05 Rinse aid dosage setting.

Increase the rinse aid dosage:
• If the dishes have water marks.

Decrease the rinse aid dosage:

• If the dishes have a sticky white/blue film.
• If the dishes are streaked.
• Build-up of foam. If you have very soft water, the
rinse aid can be diluted 50:50 with water.

2. Water hardness 2:00 - 2:09 Adjusting the water softener. Read off the appropriate
setting from the water hardness table below.

°dH °fH °dH °fH

0-5 0-9 20-24 35-43

6-8 10-14 25-29 44-52

9-11 15-20 30-39 53-70

12-14 21-25 40-49 71-88

15-19 26-34 50+ 89+

Do not forget to put salt in the salt compartment after

you have set the water softener to 2:01 - 2:09.
For a water supply with a hardness under 6°dH (9°fH),
select 2:00. The water softener is deactivated and no
salt is needed.

9
 Settings Options

3. TAB 3:00 (Off) You can activate this setting when using 3-in-1/
(3-in-1/all-in-one detergent) 3:01 (On) All-in-one detergent. The dishwashing programmes
automatically adapt to provide the best possible
dishwashing and drying results every time. If this setting
is activated there is no need to add rinse aid since this
option disables rinse aid dispensing. It also reduces the
amount of salt added to the water softener. Note that
salt must be put in the salt compartment.
NOTE!
In order to achieve good dishwashing results, it is
essential to check which type of detergent or
all-in-one product best suits your needs! Read the
detergent packaging carefully for information on
proper use. Always follow the directions for use or
information on the detergent packaging!

10
Care and cleaning

Coarse filter Spray arms

The coarse filter traps larger food particles, which cannot Holes and bearings can sometimes become blocked.
get past the drainage pump. Empty the coarse filter as Remove any debris using a pin or the like. The spray arms
necessary. also have holes underneath.

Coarse filter

1 Lift the coarse filter by the handle. To facilitate cleaning you can remove the spray arms.
2 Empty the coarse filter. Remember to replace it! Remember to fit them firmly back into place afterwards.

Lower spray arm

Fine filter • Pull the lower spray arm straight up to release it.
Debris that collects on the fine filter is automatically rinsed
away during each wash. Clean the fine filter when
necessary.

Fine filter Upper spray arm

1 Pull out the upper basket.
2 Unscrew the spray arm bearings counterclockwise to
1 Turn the handle anticlockwise. remove the spray arm from the upper basket.
2 Lift the filter straight up using the handle. Free the coarse
filter to clean the fine filter.
3 Replace in reverse order. Check that the edges seal
properly when replacing the fine filter.
4 Lock the filter in place by turning the handle clockwise
to the stop position. The handle should point straight
out from the dishwasher.

NOTE!
The dishwasher must not be used without the filters in
place! The door and the door seal
Regularly clean the sides of the door and the door seal. Use
Dishwashing results may be affected if the coarse filter is
a slightly damp cloth (with a little cleaner if necessary).
incorrectly fitted.
The dishwasher tub
The dishwasher tub is made of stainless steel and is kept
clean through normal use.

Limescale deposits
If you have hard water, limescale deposits may build up in
the dishwasher. If this happens, run the Intensive wash
programme with two tablespoons of citric acid in the
detergent compartment (with no dishes in the machine).

11
 Front panel NOTE!
Keep the buttons clean and free from grease. Wipe them
Do not forget to replace the drainage pump stop.
clean with a dry or slightly damp cloth. Never use cleaners
– they can scratch the surface. Use the main power switch
to turn off the dishwasher before cleaning the buttons to
avoid activating any buttons unintentionally. Unblocking the inlet hose filter
If the water supply contains small particles, the outer filter
Unblocking the drainage pump on the inlet hose may become blocked, which results in
If the dishwasher still contains water after the programme Water inlet fault.
has finished, something may be blocking the drainage pump.
Such items are easily removed. 1 Turn off the machine using the main power switch and
unplug it from the wall socket.
1 Turn off the machine using the main power switch and 2 Turn off the water tap.
unplug it from the wall socket.
3 Unscrew the inlet hose.
2 Remove the coarse filter and the fine filter.
4 Carefully remove the outer filter from the inlet hose and
3 Scoop out the water from the dishwasher tub. clean it.
4 In order to inspect the drainage pump, remove the 5 Replace the filter and check that the gasket is correctly
coloured stop on the right in the bottom drain. positioned.
5 Turn the pump wheel located behind the drainage pump 6 Screw the inlet hose firmly into place.
stop by hand. Carefully remove any items.
7 Plug the machine into the wall socket and turn on the
6 Replace the drainage pump stop along with the fine and water tap. Allow the pressure to settle for a while and
coarse filters. check that the connection is watertight.
7 Plug the machine in again.
If the dishwasher still does not start and a whirring sound
is heard, the overflow protection has been activated. Outer filter on inlet
hose
• Shut off the water.
Remove the plug from the wall socket. Gasket
•
• Call the service department.

Drainage pump stop

12
Troubleshooting

Type of fault on the display Action

F10 Overfilling Clear the drainage pump. See the section Care and cleaning. If the problem
persists, call the service department.

F11 Water outlet fault See “Water remains in the dishwasher” in the table “Problem” below. If the problem
persists, call the service department.

F12 Water inlet fault Check that the water tap is on. If the problem persists, call the service department.

F40 Inlet valve leakage Turn off the water tap and call the service department.

F52 Water level fault Check that the drainage hose is fitted in accordance with the installation
instructions. If the problem persists, call the service department.

F54 Overfilling Turn off the water tap and call the service department.

F56 Circulation fault Call the service department.

Press any button to clear the error message.

Problem Possible causes Action

The buttons do not react when pressed. You have pressed the buttons too soon Wait a moment then try again.
after opening the door.

The buttons are dirty. Clean with a dry or slightly damp cloth.

The door is closed. Open the door. The buttons only react
to use when the door is open.

Cannot close door. The baskets are not correctly positioned. Check that the baskets are correctly
positioned horizontally.

Check that the dishes are not blocking

the baskets from sliding properly into
place.

The dishwasher does not start. The door is not properly closed. Check.

You have opened the dishwasher to add Close the door and wait. After a while,
more dishes while a programme is in the dishwasher continues the
progress. programme.

A fuse/circuit breaker has been tripped. Check.

The plug is not plugged into the wall Check.

socket.

The water tap is turned off. Check.

Overflow/leaks. Check.

A whirring sound (the drainage pump) Turn off the water tap. Pull out the plug
is heard from the dishwasher and does and call the service department.
not stop when the main power switch is
turned off.

Check that the Delayed start option has Press and hold the main power switch
not been selected. until the display turns off if you want to
cancel the Delayed start option. Restart
the dishwasher.

13
 Problem Possible causes Action

The dishes are not clean. The spray arms do not rotate. Remove the arms and clean them.

Check that the dishes are not blocking

the spray arms.

Old detergent. Detergent is a perishable Avoid large packages.

product.

Incorrect detergent dosage. Dose according to water hardness. Far

too much or far too little detergent results
in poorer dishwashing results.

Unsuitable dishwashing programme. Choose a longer programme.

Dishes loaded incorrectly. Do not cover porcelain with large bowls

or the like. Avoid placing very tall
glasses in the corners of the baskets.

Glasses and cups have toppled over Place dishes to sit steady.
during the programme.

The filter is not correctly fitted. Screw the filter firmly into place. See the
section Care and cleaning.

Spots on stainless steel or silver. Some foodstuffs, such as mustard, Rinse off these types of foodstuffs if not
mayonnaise, lemon, vinegar, salt and starting the dishwasher immediately.
dressings, can mark stainless steel if left Why not use the Rinse programme.
for too long.

All stainless steel can cause spots on In order to avoid marks and tarnishing,
silver if they come into contact during separate dishes made from different
dishwashing. Aluminium can also cause metals, such as silver, stainless steel
spots on dishes. and aluminium.

Spots or films on the dishes. The water softener is leaking salt. Check that the salt compartment lid is
properly tightened. Otherwise call the
service department.

Incorrect water softener setting. See the section Settings.

Incorrect rinse aid dosage setting. See the section Settings.

Salt compartment empty. Top up with salt. See the section Before
washing for the first time.

3-in-1/ All-in-one detergent is used and Inactivate the setting TAB (3-in-1/
the setting TAB (3-in-1/ All-in-one All-in-one detergent) and top up salt and
detergent) is activated. rinse aid.

Too high temperature and/or too much Wash crystal at a low temperature and
detergent can cause etching on crystal. with a conservative amount of detergent.
Unfortunately, this cannot be repaired, Contact the detergent manufacturer.
only prevented.

The dishes have a sticky white/blue film. Rinse aid dosage setting too high. Reduce the amount. See the sections
Before washing for the first time and
Settings. If you have very soft water, you
may want to dilute the rinse aid 50:50
with water.

Spots left after washing. Lipstick and tea can be difficult to wash Use a detergent with a bleaching agent.
off.

Detergent residue in the detergent The detergent compartment was damp The detergent compartment must be dry
compartment after dishwashing. when adding detergent. when adding detergent.

14
Problem Possible causes Action

Rattling sound when dishwashing. The dishes are not correctly placed or Check that the dishes are placed
the spray arms are not rotating. securely. Spin the spray arms to make
sure they can rotate.

1 minute appears in the display. The programme is taking longer than No action. The programme time is stored
estimated. and next time the programme is run the
corrected time will be displayed.

Water remains in the dishwasher. The filters are blocked. Clean the coarse and fine filters.

Debris in the drainage pump. Clean the drainage pump. See the
section Care and cleaning.

Kink in drainage hose. Check that the hose is free from kinks
and sharp bends.

Blocked drainage hose. Disconnect the drainage hose where it

connects to the sink unit's water trap.
Check that no debris has fastened and
that the connection has an inner
diameter of at least 14 mm.

Bad odour in dishwasher. Dirt around the seals and in corners. Clean with washing-up brush and low
foaming cleaner.

Low temperature programmes have Run a programme with a higher

been selected for a prolonged period. temperature about once a month.

The dishes are not dry enough. Depending on the load, the programme's Activate the Extra dry option.
drying cycle may be insufficient.

The dishwasher is not fully loaded. Fully load the dishwasher.

Rinse aid needs topping up or dosage Top up with rinse add or increase the
is set too low. rinse aid dosage. See the sections
Before washing for the first time and
Settings.

3-in-1/ All-in-one detergent is used and Inactivate the setting TAB (3-in-1/
the setting TAB (3-in-1/ All-in-one All-in-one detergent) and top up salt and
detergent) is activated. rinse aid.

Open the door a little once the

programme has finished.

15
 Installation

[mm]

1214
596
600 575

30
85

848- 898

670
720
718

123-173

52 51

Nominal dimensions. Actual measurements may vary.

Safety instructions Transport protection for the door

• Connections to electricity, water and drainage must be Do not forget to remove the transport protection for the door
performed by a qualified professional. when unpacking the dishwasher.
• Always follow applicable regulations for water, drainage
and electricity.
• Take care during installation! Wear protective gloves!
There must always be two people!
• Place a drip tray on the floor beneath the dishwasher to
REMOVE
prevent damage from any water leaks.
• Before screwing the dishwasher into place, test the
dishwasher by running the Rinse programme. Check
that the dishwasher fills with water and drains. Check
also that none of the connections leak.

WARNING!
Turn off the water supply when installing the dishwasher!

WARNING!
The plug must be disconnected or power to the socket
turned off while the work is carried out!

16
Placing the dishwasher
The dishwasher is intended for freestanding installation, but
can also be installed under a worktop.

Adjust the height and slide the dishwasher

into place

6 Make any final adjustments to the front feet (the

24 mm dishwasher may lean no more than 5 mm).
7 Once the feet are properly adjusted, tighten the anti-tip
feet firmly against the floor.

The dishwasher can also be installed in a recess without

its worktop. See Remove dishwasher worktop.
Freestanding
1 Make sure the area on which the dishwasher is to be Attach the plinth
installed is firm. Adjust the dishwasher's height using (Packed inside the dishwasher.)
the four feet so that the dishwasher is level. The
dishwasher may lean no more than 5 mm.
2 Once the feet are properly adjusted, tighten the anti-tip
feet firmly against the floor.

Anti-tip feet

Drainage connection

min.
Built-in
14 mm
1 Start by measuring the height from the floor to the
bottom edge of the worktop.
2 Measure the height from the floor to the top edge of the
dishwasher.
3 Adjust the dishwasher's feet by turning them clockwise
to raise or anticlockwise to lower the machine.
4 Check that there is an air gap of at least 3 mm between
the underside of the worktop and the top edge of the
dishwasher.
5 Slide the dishwasher into place.
• Pull through the drainage and supply hoses when
the machine is slid into place.
• Check that the hoses have no kinks or sharp bends,
and check that there is nothing that can damage the
hoses.

17
 Connection to water supply
Use only the inlet hose supplied with the dishwasher. Do
not re-use old or other spare hoses.

The supply pipe must be fitted with a water tap (stopcock).

The water tap must be easily accessible, so that the water
can be shut off if the dishwasher has to be moved.

Once the installation is complete, turn on the water tap and

allow the pressure to settle for a while. Check that all
connections are watertight.

Connection to cold water supply

Connect the dishwasher to the cold water supply if the
building is heated using oil, electricity or gas.

Connection to hot water supply

Connect the dishwasher to the hot water supply (max. 70
350--950 mm min. 350 mm °C) if the building is heated using an energy-efficient means
such as district heating, solar power or geothermal power.
Choosing a hot water connection cuts dishwashing times
and reduces the dishwasher's energy consumption.
The drainage hose may be extended by a maximum of 3 m
(the total length of the drainage hose must not exceed 4.5
m). Any joins and connecting pipes must have an internal NOTE!
diameter of at least 14 mm. However, the drainage hose Do not exceed the permitted water supply temperature.
should ideally be replaced with a new hose without joins. Certain materials used in some cookware cannot
No part of the drainage hose may be more than 950 mm withstand strong heat. See Fragile dishes in the chapter
above the bottom of the dishwasher. The hose must not be Loading the dishwasher.
routed directly to a floor drain or the like. In such cases, the
hose can act as a siphon and empty the dishwasher.
Electrical connection
The hose must always discharge at least 350 mm above
Information about the electrical connection can be found on
the bottom of the machine.
the serial number plate. This specification must match the
Ensure that the drainage hose has no kinks. electricity supply.

The dishwasher must be connected to an earthed socket.

NOTE!
The electric wall socket must be placed outside of the
When the drainage hose is routed to a connection nipple
installation area to be easily accessible after installing the
on the sink unit's water trap (see illustration 1), please
dishwasher. Do not use an extension cord!
note that the hose must be attached at the same height
as the underside of the sink unit, otherwise dishwater from
the sink may flow back into the dishwasher. For other NOTE!
connection alternatives, see illustrations 2 and 3. Repairs and maintenance relating to safety or
performance must be carried out by a qualified
1 2 3 professional.

Remove dishwasher worktop

The dishwasher can be installed in a recess without its
worktop. If the dishwasher's worktop is removed, the
dishwasher must be installed so that it is enclosed on both
sides and is under a separate worktop. If the dishwasher is
installed so that one of the sides is visible, a brace must be

18
 Service

fitted to the rear edge of the dishwasher. Accessories can Read the chapter Troubleshooting before contacting the
be purchased where you bought the dishwasher. service department. If you have encountered a problem that
you cannot resolve, please contact your nearest dealer, see
www.gorenje.com.
3
When making contact, provide the details on the serial
2 number plate. Include the article number (1) and the serial
number (2).

ART. NO. 1
SERIAL NO.
2
2x

For recess installation, see the section Placing the

dishwasher.

19
 Information for test institute

Request test institute information via e-mail

[email protected].
ART. NO. 1
The request should include the details on the serial number SERIAL NO.
2
plate. Include the article number (1) and the serial number
(2).

20
Your notes

21
 Your notes

22
Your notes

23
 Technical information

Information on energy labelling

Information sheet, in compliance with Commission Delegated Regulation (EU) No. 1059/2010

Gorenje
Model designation: GS63160
Number of standard place settings: 13 1)
Energy efficiency class: A+
Annual energy consumption(AEC): 295 kWh per year 2)
Energy consumption of the standard cleaning cycle(Et):1.04 kWh
Power consumption
Off-mode (Po): 0.49 W
Left-on mode (Pl): 0.49 W
Annual water consumption (AWC): 3080 litres per year 3)
Drying efficiency class: A 4)
Standard programme: Eco wash 5) , no options
Programme time for the standard cleaning cycle: 250 minutes
Duration of the left-on mode (Tl): Infinite
Noise emissions: 47 dB(A) re 1 pW
1) In accordance with standard, EN 50242.
2) Based on 280 standard cleaning cycles with a cold water connection and consumption in accordance with energy saving mode. The actual
energy consumption depends on how the machine is used.
3) Based on 280 standard cleaning cycles. The actual water consumption depends on how the machine is used.
4) On a scale from G (least efficient) to A (most efficient).
5) This dishwashing programme is the standard cleaning cycle used to compile the energy labelling information. It is intended for washing
normally dirty dishes and is the most effective programme in terms of combined energy and water consumption.

Technical data
Height: 848-898 mm
Width: 600 mm
Depth: 596 mm
Weight: 55 kg 1)
Water pressure: 0.03–1.0 MPa
Electrical connection:See serial number plate
Rated power: See serial number plate
1)
Art. No.: 547751. Rev. 02. We reserve the right to make changes.
Weight can vary due to different specifications.

 en (01-17)
24 www.gorenje.com