Hello world, 285o!

{uni}[WEI][arm64]
svn:4a613103623ea907 (Dec 28 2018 13:43:11)
flash_type = 2, secure_type = 2
b8062204=a5
HW off: 146
ABCDE[RPMB]Auth Key not Ready(7)!!!
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CTRL_REG_reg=0x1
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CPU_FLASH_REGION=0xba20b820
[go atf]U

U-Boot 2012.07 (Nov 06 2020 - 04:52:25) r-hdmi_test_only-2083-gccbc0125f5

[ENV] Writing to Factory...

factory_tarsize = 0x1c0800
[FAC] factory_save: MMC
[FAC] Save to eMMC (blk#:0x14000, buf:0x23900000, len:0x1c0a00)
[FAC] Save to eMMC (seq#:0xe957, pp:1)
done
Factory Address:0x2000000, Size:0x1000000!
Factory Read Only Address:0x1800000, Size:0x400000!
:Y: env_panel_set_default panel_src=0, panel_select=0
:Y: try to get setting from <tmp/factory/bin_panel/rtkPanel.ini>
:ERROR:--------is not find tmp/factory/bin_panel/rtkPanel.ini
:Y: from ini failed, use default [0]
default pq file tmp/factory/bin_panel/PanelParam/vip_default_pq.bin exsit!

<<<<<<Panel: JE445D3HA1L>>>>>>>>

<<<<<<parameter_len: 140 >>>>>>>>

[WARN] para_no is 33 > 32. Clear more pcb_parameter env.
logbuf fifo[0] [buffer=1ca0e000], [size=10000]
logbuf fifo[1] [buffer=1ca1e000], [size=2000]
logbuf fifo[2] [buffer=1ca20000], [size=10000]
logbuf fifo[3] [buffer=1ca30000], [size=10000]
logbuf fifo[4] [buffer=1ca40000], [size=10000]
logbuf fifo[5] [buffer=1ca50000], [size=20000]
logbuf fifo[6] [buffer=1ca70000], [size=10000]
------------parse tmp/factory/vsc_resource.xml ok!
------------parse tmp/factory/throttle_resource.xml ok!
------------parse tmp/factory/cpu_resource.xml ok!
[get_factory_ir_table_from_factory:1558]Err:tmp/factory_ro/ir_table.bin parse su
c, size:359
panel initialize....
panel_init_1st 0529_1022
Disp HTotal=2199, Htotal 4x alignment=2199
den_h_start=140, den_h_end=2060
[uzu] dvtotal(b8028504 = 464)
[uzu] dhtotal(b8028508 = 8970897)
[uzu] dh den start(b8028518 = 8c080c)
[uzu] dv den start(b802851c = 100448)
[uzu] uzudtg control (b8028500 = 80000051)
[memc] dvtotal(b8028604 = 464)
[memc] dhtotal(b8028608 = 8970897)
[memc] dh den start(b802861c = 8c080c)
[memc] dv den start(b8028618 = 100448)
[memc] uzudtg control (b8028100 = 50000)
###### SFG_SFG_CTRL_0_reg : 1 ########
##### drvif_clock_set_dclk : 149000000 ###########

After Mapping (ulFreq:596000000) (div:4)======

dclk_Temp:662222
nMCode:66, f_code:455
Panel: ulFreq:596000000, nDPLL:0, Mcode:66, Ncode:3, offset:0

#### 0xb8000208[1c]

#### [drvif_clock_set_dtg_uzu_div]

#### 0xb8000208[400001c]

#### [drvif_clock_set_dtg_memc_div]
=== Panel Type : 0 ===
=== iCONFIG_PANEL_CUSTOM_INDEX : 0 ===
===panel_lvds_tx ===0
=== RTD285O LVDS FHD tx phy ===[GDMA](Frome bdinfo)BUSH = 499 ; DISP = 148
=== Panel Index : 0 ===
[TCON]No demand of TCON(outputgamma,valc,OD,demura) setting.
In: serial
Out: serial
Err: serial
Net: r8168: REALTEK RTL8168 @0x18016000
Hit Esc or Tab key to enter console mode or rescue linux: 0
------------CONFIG_ANDROID_RECOVERY

------------CONFIG_SYS_RTK_EMMC_FLASH
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001
(Re)start USB...
USB0: ----------- ehci_hcd_init -----------
#@# ehci_hcd_init(452) ehci mac0
----------- usb2_crt on(0) -----------
----------- usb2_crt -----------
----------- usb2_crt on(1) -----------
----------- usb2_crt -----------
[ehci], dbg, ---- ehci_usb2_load_phy_params start ----
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, ---- ehci_usb2_load_phy_params complete ----
[ehci], info, #@# usb2_phy_setting(335) +++ for usbphy setting 20170420
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe1 set 0x18 get 0x18
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe2 set 0x34 get 0x34
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe3 set 0xcd get 0xcd
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe5 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xdb get 0xdb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x53 get 0x53
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x41 get 0x41
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe4 set 0x68 get 0x68
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0x23 get 0x23
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe0 set 0x27 get 0x27
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0x61 get 0x61
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf0 set 0xfc get 0xfc
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf1 set 0x88 get 0x88
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf3 set 0x31 get 0x31
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf5 set 0x15 get 0x15
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf6 set 0x1 get 0x1
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf7 set 0x8a get 0x8a
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0xbb get 0xbb
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe1 set 0x70 get 0x70
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe2 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe3 set 0x12 get 0x12
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe4 set 0x0 get 0x0
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe5 set 0xf get 0xf
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe6 set 0x58 get 0x58
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xe7 set 0xe3 get 0xe3
[ehci], dbg, set_usb2_phy, port 1 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 2 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], dbg, set_usb2_phy, port 3 phy_reg 0xf4 set 0x9b get 0x9b
[ehci], info, #@# usb2_phy_setting(337) ---
----------- ehci_usb_mac_init -----------
USB EHCI 1.00
scanning bus 0 for devices... 2 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
1: Hub, USB Revision 2.0
- u-boot EHCI Host Controller
- Class: Hub
- PacketSize: 64 Configurations: 1
- Vendor: 0x0000 Product 0x0000 Version 1.0
Configuration: 1
- Interfaces: 1 Self Powered 0mA
Interface: 0
- Alternate Setting 0, Endpoints: 1
- Class Hub
- Endpoint 1 In Interrupt MaxPacket 8 Interval 255ms

2: , USB Revision 2.10

- Realtek 802.11n WLAN Adapter 00e04c000001
- Class:
- PacketSize: 64 Configurations: 1
- Vendor: 0x0bda Product 0xb720 Version 2.0
Configuration: 1
- Interfaces: 3 Self Powered Remote Wakeup 500mA
Interface: 0
- Alternate Setting 0, Endpoints: 3
- Class
- String: "Bluetooth Radio"
- Endpoint 1 In Interrupt MaxPacket 16 Interval 4ms
- Endpoint 2 Out Bulk MaxPacket 512
- Endpoint 2 In Bulk MaxPacket 512
Interface: 1
- Alternate Setting 0, Endpoints: 2
- Class
- String: "Bluetooth Radio"
- Endpoint 3 Out Isochronous MaxPacket 0
- Endpoint 3 In Isochronous MaxPacket 0
- Endpoint 3 Out Isochronous MaxPacket 9
- Endpoint 3 In Isochronous MaxPacket 9
 - Endpoint 3 Out Isochronous MaxPacket 17
- Endpoint 3 In Isochronous MaxPacket 17
- Endpoint 3 Out Isochronous MaxPacket 25
- Endpoint 3 In Isochronous MaxPacket 25
- Endpoint 3 Out Isochronous MaxPacket 33
- Endpoint 3 In Isochronous MaxPacket 33
- Endpoint 3 Out Isochronous MaxPacket 49
- Endpoint 3 In Isochronous MaxPacket 49
Interface: 2
- Alternate Setting 0, Endpoints: 6
- Class Vendor specific
- String: "802.11n WLAN Adapter"
- Endpoint 4 In Bulk MaxPacket 512
- Endpoint 5 Out Bulk MaxPacket 512
- Endpoint 6 Out Bulk MaxPacket 512
- Endpoint 7 In Interrupt MaxPacket 64 Interval 3ms
- Endpoint 8 Out Bulk MaxPacket 512
- Endpoint 9 Out Bulk MaxPacket 512

[INFO]check_usb_file_ini:fatload start.

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **

** Invalid boot device **

stopping USB..
----------- usb2_crt on(0) -----------
----------- usb2_crt -----------
find ini file failed

Start Boot Setup ...

FW Table to 0x06800000, size=0x00000a00 (0x06800a00)
FW Table fr 0x04000000, fw count: 50
[OK] fw_entry[0] offset = 0x8000 length = 0x1ab0ddc (paddings = 0x2800000) act_s
ize = 0 part_num = 0
[OK] fw_entry[1] offset = 0x2808000 length = 0x1d9f88 (paddings = 0x500000) act_
size = 0 part_num = 0
[OK] fw_entry[2] offset = 0x2d08000 length = 0x3d8dd8 (paddings = 0x600000) act_
size = 0 part_num = 0
[OK] fw_entry[3] offset = 0x3308000 length = 0xa19a0 (paddings = 0xc00000) act_s
ize = 0 part_num = 0
[OK] fw_entry[4] offset = 0x3f08000 length = 0x5eec00 (paddings = 0x800000) act_
size = 0 part_num = 0
Normal boot fw follow...
Linux Kernel:
FW Image to 0x00108000, size=0x01ab0ddc (0x01bb8ddc)
FW Image fr 0x04008000 (non-lzma)
Audio FW 1:
FW Image to 0xdeaddead, size=0x001d9f88 (0xdecb7e35)
FW Image fr 0x06808000 (non-lzma)
Enter standby, skip this entry
Video FW 1:
FW Image to 0xdeaddead, size=0x003d8dd8 (0xdeeb6c85)
FW Image fr 0x06d08000 (non-lzma)
 Enter standby, skip this entry
TEE FW target_addr = 0x16008000
(skip)
show raw video raw file ddr 0x84f00000 len 0xec5e00
FW Image to 0x84f00000, size=0x005eec00 (0x854eec00)
FW Image fr 0x07f08000 (non-lzma)
Enter standby, skip this entry
current avb status on
do_avb_init success!!!!!
current avb status on
## Android Verified Boot 2.0 version 1.1.0
sw sha256 ret 0
sw sha256 ret 0

EVer:2▒1067059
(build:3
Apr 2 2020 309:51:53)
share[0x0]:0x360001
share[0x1]:0x10000a
share[0x2]:0x0
share[0x3]:0x0
share[0x4]:0x0
share[0x5]:0x0
share[0x6]:0x0
share[0x7]:0x0
share[0x8]:0x0
share[0x9]:0x0
share[0xa]:0x0
share[0xb]:0x0
share[0xc]:0x0
share[0xd]:0x1
share[0xe]:0xbf40fb04
share[0xf]:0xf30cf700
share[0x10]:0xf40bbf40
share[0x11]:0xf40bdf20
share[0x12]:0xfc03bf00
share[0x13]:0xfd020707
share[0x14]:0x0
share[0x15]:0x0
share[0x16]:0x3
share[0x17]:0x0
share[0x18]:0x0
share[0x19]:0x0
share[0x1a]:0x0
share[0x1b]:0x0
share[0x1c]:0x0
share[0x1d]:0x401f00
share[0x1e]:0x401e00
share[0x1f]:0x401d00

PwNum:0x30x0 M
0xa, 0xas
0x14, 0x14s
0x1e, 0x1es
0x28, 0x28s
0x32, 0x32s
0x1 M
0xa, 0x46s
0x14, 0x50s
0x1e, 0x5as
0x28, 0x64s
0x32, 0x6es
0x2 M
0xa, 0x82s
0x14, 0x8cs
0x1e, 0x96s
0x28, 0xa0s
0x32, 0xaas
0x3 M
0xa, 0xbes
0x14, 0xc8s
0x1e, 0xd2s
0x28, 0xdcs
0x32, 0xe6s
0x4 M
0xa, 0xfas
0x14, 0x104s
0x1e, 0x10es
0x28, 0x118s
0x32, 0x122s
0x5 M
0xa, 0x136s
0x14, 0x140s
0x1e, 0x14as
0x28, 0x154s
0x32, 0x15es
0x6 M
0xa, 0x172s
0x14, 0x17cs
0x1e, 0x186s
0x28, 0x190s
0x32, 0x19as
0x7 M
0xa, 0x1aes
0x14, 0x1b8s
0x1e, 0x1c2s
0x28, 0x1ccs
0x32, 0x1d6s
0x8 M
0xa, 0x1eas
0x14, 0x1f4s
0x1e, 0x1fes
0x28, 0x208s
0x32, 0x212s
0x9 M
0xa, 0x226s
0x14, 0x230s
0x1e, 0x23as
0x28, 0x244s
0x32, 0x24es
0xa M
0xa, 0x262s
0x14, 0x26cs
0x1e, 0x276s
0x28, 0x280s
0x32, 0x28as
0xb M
0xa, 0x29es
0x14, 0x2a8s
0x1e, 0x2b2s
0x28, 0x2bcs
0x32, 0x2c6s
0xc M
0xa, 0x2das
0x14, 0x2e4s
0x1e, 0x2ees
0x28, 0x2f8s
0x32, 0x302s
0xd M
0xa, 0x316s
0x14, 0x320s
0x1e, 0x32as
0x28, 0x334s
0x32, 0x33es
0xe M
0xa, 0x352s
0x14, 0x35cs
0x1e, 0x366s
0x28, 0x370s
0x32, 0x37as
0xf M
0xa, 0x38es
0x14, 0x398s
0x1e, 0x3a2s
0x28, 0x3acs
0x32, 0x3b6s
0x10 M
0xa, 0x3cas
0x14, 0x3d4s
0x1e, 0x3des
0x28, 0x3e8s
0x32, 0x3f2s
0x11 M
0xa, 0x406s
0x14, 0x410s
0x1e, 0x41as
0x28, 0x424s
0x32, 0x42es
0x12 M
Keypad_match.
wake

PwNum:0x3
EMCU final!
BI$
Hello world, 285o!{uni}[WEI][arm64]
svn:4a613103623ea907 (Dec 28 2018 13:43:11)
flash_type = 2, secure_type = 2
b8062204=a5
HW off: 146
ABCDE[RPMB]Auth Key not Ready(7)!!!
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CTRL_REG_reg=0x1
Test Print1 SB2_CTRL_REG_reg=0x0
Test Print1 SB2_CPU_FLASH_REGION=0xba20b820
[go atf]U
U-Boot 2012.07 (Nov 06 2020 - 04:52:25) r-hdmi_test_only-2083-gccbc0125f5

Mac Address use 00:CB:B4:64:30:DA in env

[ENV] Writing to Factory...
factory_tarsize = 0x1c0800
[FAC] factory_save: MMC
[FAC] Save to eMMC (blk#:0x10000, buf:0x23900000, len:0x1c0a00)
[FAC] Save to eMMC (seq#:0xe958, pp:0)
done
Factory Address:0x2000000, Size:0x1000000!
Factory Read Only Address:0x1800000, Size:0x400000!
:Y: env_panel_set_default panel_src=0, panel_select=0
:Y: try to get setting from <tmp/factory/bin_panel/rtkPanel.ini>
:ERROR:--------is not find tmp/factory/bin_panel/rtkPanel.ini
:Y: from ini failed, use default [0]
default pq file tmp/factory/bin_panel/PanelParam/vip_default_pq.bin exsit!

<<<<<<Panel: JE445D3HA1L>>>>>>>>

<<<<<<parameter_len: 140 >>>>>>>>

[WARN] para_no is 33 > 32. Clear more pcb_parameter env.
logbuf fifo[0] [buffer=1ca0e000], [size=10000]
logbuf fifo[1] [buffer=1ca1e000], [size=2000]
logbuf fifo[2] [buffer=1ca20000], [size=10000]
logbuf fifo[3] [buffer=1ca30000], [size=10000]
logbuf fifo[4] [buffer=1ca40000], [size=10000]
logbuf fifo[5] [buffer=1ca50000], [size=20000]
logbuf fifo[6] [buffer=1ca70000], [size=10000]
------------parse tmp/factory/vsc_resource.xml ok!
------------parse tmp/factory/throttle_resource.xml ok!
------------parse tmp/factory/cpu_resource.xml ok!
[get_factory_ir_table_from_factory:1558]Err:tmp/factory_ro/ir_table.bin parse su
c, size:359

board_init_r board.c 2021 -- (0) key=0x1b

board_init_r board.c 2021 -- (1) key=0x1b
board_init_r board.c 2021 -- (2) key=0x1b
board_init_r board.c 2021 -- (3) key=0x1b
board_init_r board.c 2021 -- (4) key=0x1b
panel initialize....
panel_init_1st 0529_1022
Disp HTotal=2199, Htotal 4x alignment=2199
den_h_start=140, den_h_end=2060
[uzu] dvtotal(b8028504 = 464)
[uzu] dhtotal(b8028508 = 8970897)
[uzu] dh den start(b8028518 = 8c080c)
[uzu] dv den start(b802851c = 100448)
[uzu] uzudtg control (b8028500 = 80000051)
[memc] dvtotal(b8028604 = 464)
[memc] dhtotal(b8028608 = 8970897)
[memc] dh den start(b802861c = 8c080c)
[memc] dv den start(b8028618 = 100448)
[memc] uzudtg control (b8028100 = 50000)
###### SFG_SFG_CTRL_0_reg : 1 ########
##### drvif_clock_set_dclk : 149000000 ###########

After Mapping (ulFreq:596000000) (div:4)======

dclk_Temp:662222
nMCode:66, f_code:455
Panel: ulFreq:596000000, nDPLL:0, Mcode:66, Ncode:3, offset:0

#### 0xb8000208[1c]

#### [drvif_clock_set_dtg_uzu_div]

#### 0xb8000208[400001c]

#### [drvif_clock_set_dtg_memc_div]
=== Panel Type : 0 ===
=== iCONFIG_PANEL_CUSTOM_INDEX : 0 ===
===panel_lvds_tx ===0
=== RTD285O LVDS FHD tx phy ===[GDMA](Frome bdinfo)BUSH = 499 ; DISP = 148
=== Panel Index : 0 ===
[TCON]No demand of TCON(outputgamma,valc,OD,demura) setting.
panel_init_2nd 6300:
panel_init_2nd
rtk_hw_get_divider M_best:0 N_best:1 freq:4700000 totalcnt:254 duty_max:255
set pwm duty=182 success!!

panel_init_2nd,6349 iLVDS_TO_LIGHT_ON_ms=200
panel_init_2nd,6350 iPANEL_TO_LVDS_ON_ms=50
panel_init_2nd,6351 iLIGHT_TO_LDVS_OFF_ms=200
panel_init_2nd,6352 iLVDS_TO_PANEL_OFF_ms=40
:Y: boot current backlight is on ! [1]
bootparam is NULL. run default sscg.
In: serial
Out: serial
Err: serial
Net: r8168: REALTEK RTL8168 @0x18016000
Hit Esc or Tab key to enter console mode or rescue linux: 0
------------CONFIG_ANDROID_RECOVERY

------------CONFIG_SYS_RTK_EMMC_FLASH

Press Esc Key

Find CONFIG_BOARD_299S_TV010_BGA_EERPOM
name=PIN_KEYPAD_PWR ppcb_enum.Name=PIN_KEYPAD_PWR, ppcb_enum.info=74000a00000001

Enter console mode, disable watchdog ...

Realtek> help
avb - Provides commands for testing Android Verified Boot 2.0 functionality
bdinfo - print Board Info structure
bootr - boot realtek platform
cp_ddts - CP ddts test
cusboot - cusboot [port, 1] [dev, 0]
dcache - enable or disable data cache
diseqc - DISEQC command description/usage
dssinfo - print dss
env - environment handling commands
facro - FACTORY read-only sub system
factory - FACTORY sub system
fatinfo - print information about filesystem----usage: fatinfo <interface>
<dev[:part]>
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
go - start application at address 'addr' or start running fw
help - print command description/usage
hwmonitor- hw monitor setting
i2c - i2c test
icache - enable or disable instruction cache
irda - irda - select irda protocol
kboot - start kboot function
layout - show flash layout
loady - load binary file over serial line (ymodem mode)
logbuf - rtd logbuffer sub system
loglevel- set console loglevel to env and bootcode will pass this value to kerne
l
lsadc - Test
md - memory display-----md [.b, .w, .l] address [# of objects]

mmc - MMC sub system

Usage:
mmc info - display info of the current MMC device
----------
mmc debug - show current debug output behavior
mmc debug on - enable debug message
mmc debug off - disable print debug message
----------
mmc read addr blk# cnt
mmc write addr blk# cnt
mmc readb addr byte_addr# byte_cnt
mmc writeb addr byte_addr# byte_cnt
----------
mmc erase blk# cnt
mmc erase secure blk# cnt
mmc erase trim blk# cnt
----------
mmc wp info
mmc wp enable start_blk# blk_cnt - enable write-protect setting on mmc device
mmc wp disable start_blk# blk_cnt - disable write-protect setting on mmc device
mmc wp disable_whole - disable write-protect setting on whole mmc device
mmc wp chks start_blk# blk_cnt - To check write-protect status corresponds to the
start_addr
mmc wp chks_all - To check write-protect status all emmc.
mmc wp chkt start_blk# blk_cnt - To check write-protect type corresponds to the
start_addr
mmc wp chkt_all - To check write-protect type all emmc.
----------
mmc compare blk# cnt loop - write pattern cnt blocks to blk#, then read back
compare
mmc compare w_pat - write pattern to mmc
mmc compare chk_pat - check pattern of mmc
----------
mmc extcsd - Display all of ext_csd.
mmc extcsd idx# - check item of idx# from ext_csd.
mmc extcsd idx# w val# - set value to assigned idx# to ext_csd.
----------
mmc chgpart idx# - chang partiton to ixd#; 0:user; 1:boot1; 2:boot2
----------
mmc lftest result - Display last result of life testing
mmc lftest loop# [show] - mmc write/read life testing, #loop is whole mmc testing
sycle,
"show" for display cmd information, can skip.
----------
mmc rpmb read addr blk# cnt [address of auth-key] - block size is 256 bytes
mmc rpmb write addr blk# cnt <address of auth-key> - block size is 256 bytes
mmc rpmb key <address of auth-key> - program the RPMB authentication key.
mmc rpmb counter - read the value of the write counter
----------
mmc rescan - initialize emmc again
mmc part - lists available partition on current mmc device
mmc dev [dev] [part] - show or set current mmc device [partition]
mmc list - lists available devices
mmc report - report the device life time
mmc speed - display current speed that emmc running.
mmc test case1-6 start size chunk
case1 : sequential read
case2 : sequential write
case3 : random read
case4 : random write
case5 : same address write
case6 : random read & write

mtest - simple RAM read/write test

mw - memory write (fill)
panel - select the specific panel config from panel array
ping - send ICMP ECHO_REQUEST to network host
print - print - turn on/off print message.

pwm - PWM command description/usage

pwminvert- set the pwminvert [on|off]

reset - Perform RESET of the CPU

rtkmmc - RTK MMC direct function
saveenv - save environment variables to persistent storage
setuart - uart - turn on/off uart0.

showvdq - showvdq - show vdq info

sleep - delay execution for some time
spanel - spanel - select panel
swu - FW upgrade sub-system
swuu - FW upgrade sub-system
tftp - download image from TFTP server
tftpput - TFTP put command, for uploading files to a server
timelog - set the bootloader time log [on|off]

tuner - tuner - select tuner model;

uart2rbus- uart2rbus [off|on|on_0|on_1|on_2]

usb - USB sub-system

vsyncapad- vsyncapad [I2S|VGA]

wdt - watch dog enable/disable

Realtek> avb - Provides commands for testing Android Verified Boot 2.0
functionality
current avb status on
avb - Provides commands for testing Android Verified Boot 2.0 functionality

Usage:
avb init <dev> - initialize avb2 for <dev>
avb read_rb <num> - read rollback index at location <num>
avb write_rb <num> <rb> - write rollback index <rb> to <num>
avb is_unlocked - returns unlock status of the device
avb get_uuid <partname> - read and print uuid of partition <part>
avb read_part <partname> <offset> <num> <addr> - read <num> bytes from
partition <partname> to buffer <addr>
avb read_part_hex <partname> <offset> <num> - read <num> bytes from
partition <partname> and print to stdout
avb write_part <partname> <offset> <num> <addr> - write <num> bytes to
<partname> by <offset> using data from <addr>
avb verify - run verification process using hash data
from vbmeta structure

Realtek> bdinfo - print Board Info strucb system

bdinfo - print Board Info structure

Usage:
bdinfo
Realtek> loglevel- set cnsole loglevel to
l
Unknown command 'loglevel-' - try 'help'
Realtek> lsadc - Test
[LSADC] The parameter is incorrect
lsadc init index=<index>
lsadc get index=<index>
Realtek> md - memorydead/write test
md - memory display

Usage:
md [.b, .w, .l] address [# of objects]
Realtek> nd ICMP ECHO_RQUEST to network husage
Unknown command 'nd' - try 'help'
Realtek> pwminvert- set the pwminvert [o| - RTK MMC direct function
syntax error
Realtek> saveenv - save nvironment variab
saveenv - save environment variables to persistent storage

Usage:
saveenv
Realtek> setart - uart - turn on/off uarel - select panel
Unknown command 'setart' - try 'help'
Realtek> wu - FW upgrade sub-system
Unknown command 'wu' - try 'help'
Realtek> smage from FTP server
Unknown command 'smage' - try 'help'
Realtek> tftpput - er
TFTP to server 192.168.0.3; our IP address is 192.168.0.200
Filename 'er'.
Save address: 0x0
Save size: 0x0
Saving: T T
Abort
Realtek> <INTERRUPT>
Realtek> mmcinfo
Unknown command 'mmcinfo' - try 'help'
Realtek>