Scribd
Upload
15 views5 pages

ELG4139MT2Preparation

The document outlines preparation for a midterm exam in ELG4139, focusing on various electrical engineering applications involving different types of switches, energy systems, and converters. It includes questions on proposing switches for specific applications, drawing block diagrams for energy systems, and performing calculations related to DC to DC converters and motor drives. Additionally, it covers topics like pulse-width modulation and the operation modes of choppers.

Uploaded by

hashan A.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
15 views5 pages

ELG4139MT2Preparation

The document outlines preparation for a midterm exam in ELG4139, focusing on various electrical engineering applications involving different types of switches, energy systems, and converters. It includes questions on proposing switches for specific applications, drawing block diagrams for energy systems, and performing calculations related to DC to DC converters and motor drives. Additionally, it covers topics like pulse-width modulation and the operation modes of choppers.

Uploaded by

hashan A.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

ELG4139: Midterm 2 Preparation

Question 1:
Propose a proper switch (MOSFET/Thyristor/GTO/IGBT) for the following applications

An inverter for the light-rail train (LRT) locomotive operating from a DC


supply of 750 V. The locomotive is rated at 150 kW. The induction motor is to
run from standstill up to 200 Hz, with power switches frequencies up to 10
kHz.
A switch-mode power supply (SMPS) for remote telecommunication
equipment is to be developed. The input voltage is obtained from a photovoltaic
array that produces a maximum output voltage of 100 V and a minimum
current of 200 A. The switching frequency should be higher than 100 kHz.
A HVDC transmission system transmitting power of 300 MW from one AC
system to another AC system both operating at 50 Hz, and the DC link voltage
operating at 2.0 kV.
A variable frequency drive (VFD) for a vacuum cleaner using a three phase AC
motor.
An ordinary compact fluorescent lamp (CFL).
An induction heater.
Battery charger up to 40 A.
An industrial motor drive of more than 1000 kW and more than 2000 kV.
A motor drive of more less than 250 W and less than 100 kV.
Shunt compensation within FACTS (Flexible AC Transmission Systems)
Question 2: Draw a block diagram for the following energy systems.

Grid-
connected
wind energy
system using
an induction
generator

Grid-
connected
Solar energy
System
(20 solar panels,
each with 12.5
V)

AC Motor
Drive

A switching
mode power
Supply with
power factor
Correction
Question 3: Consider the following DC to DC converter. L = 24 µH. It is operating in DC
steady-state under the following condition: Vin = 20 V, D = 0.6, Po = 14 W and fs = 200 kHz.
Calculate the values of the generated signal forms.
Question 4: Consider a boost converter, the inductor current has Δi = 2 A, V = 5 V, V = 12 V,
L in o
P = 11 W, f = 200 kHz. Calculate L and values of the generated signal forms.
o s

Question 5: Draw a 180 electrical degrees of a waveform that is generated through pulse-width
modulation. Show the details of chopping pieces out of the wave to control the fundamental in
the output.

Question 6: Consider the following step-down and step-up chopper (two quadrant chopper). The
circuit can provide both motoring forward operation (S1 and D1) and regenerating braking
operation (S2 and D2).

For the Buck circuit (S1 and D1), determine the duty cycle and turn-on time in the motoring
mode if n = 500 r/min, and io = 90 A. Assume Vs = 120 V, Ea = 0.1 n, Ra = 0.2 Ohm, fs = 300 Hz.
Calculate the absorbed power in the motor armature winding and the power delivered by the
voltage supply. What is the role of the diode (D1)? Draw the Buck (step-down chopper) voltage
waveform first with D1 and second without D1.

For the Boost (S2 and D2) circuit, determine the duty cycle and turn-on time in the motoring
mode if n = 380 r/min, and io = -90 A. Assume Vs = 120 V, Ea = 0.1 n, Ra = 0.2 Ohm, fs = 300
Hz. Calculate the absorbed power in the motor armature winding and the power delivered by the
voltage supply. Also draw the output voltage waveform.

Question 7: An IGBT- based one-quadrant chopper is used to power a DC motor. The motor
armature winding Ra = 0.25 Ohm and winding inductance La = 1 mH. The input DC voltage Vd =
250 V. The armature constant of the DC motor is Kaφ = 0.98 V/rad/sec. When the duty cycle is
0.5, the motor is running at 1200 rpm. The switching frequency fs = 1 kHz. Determine the
operation mode of the converter and the ripple torque ΔT. Hint: The converter usually operates at
two modes: discontinuous conduction mode (DCM) and continuous conduction mode (CCM).
DCM occurs because switching ripple in inductor current or capacitor voltage causes polarity of
applied switch current or voltage to reverse (2 marks).

Vd e ton /   1 E a V  Ea
Use: Ea = Kaφ; ΔT= KaφΔI; I min  ts / 
 ; I max  d (1  e ton /  )
Ra e  1 Ra Ra

You might also like