Error Codes List page 9

All About this machine Error Code:

page

Code: 7220

Description:

Broken in-machine thermistor wire The sensor input sampling value is greater than the reference value.

Remedy:

In-machine temperature sensor 1. Confirm that the wiring connector is firmly connected, Insert the
connector all the way in. In-machine temperature sensor - Main/engine PWB (YC1) 2. If the wiring is
disconnected, shortcircuited or has a ground fault, replace the wire. Replace the in-machine
temperature sensor PWB.

Main/Engine PWB Replace the main/engine PWB.

Code: 7800

Description:

Broken outer thermistor wire The sensor input sampling value is abnormal. (After detecting an error, it is
controlled at 23C/77 °F and 50%RH)

Remedy:

Temperature and humidity Sensor 1. Confirm that the wiring connector is firmly connected, and if
necessary, connect the connector all the way in. Temperature and humidity sensor - Main/engine PWB
(YC2) 2. If the wiring is disconnected, shortcircuited or has a ground fault, replace the wire. 3. Replace
the Temperature and humidity sensor PWB.

Main/Engine PWB Replace the main/engine PWB.

Code: 7990

Description:

Waste toner full The waste toner sensor detected the waste toner reservoir in the drum unit is full

Remedy:

Drum unit Turn the power switch off and on Replace the drum unit if not repaired.

Waste toner sensor Replace the waste toner sensor.

Code: F000

Description:

Communication error between Main/Engine PWB - Operation panel PWB

Remedy:

Connection of the wires and connectors between the main/engine PWB - the operation panel PWB. If
the connector is not inserted enough, reinsert it. Or check the wire's continuity and replace the wire if
there is no continuity.

Operation panel PWB Replace the operation panel PWB. (TSI: see page 4-138, LCD: see page 4- 141)

Main/Engine PWB Replace the main/engine PWB.

Code: F010

Description:

Main/Engine PWB Checksum error

Remedy:

Main/Engine PWB Unplug the power cord from the wall outlet, and wait five seconds. Then plug in the
power cord and then turn on the power switch. If not corrected, replace the main/ engine PWB.

Code: F020

Description:

Main/engine PWB RAM checksum error

Remedy:

Main/engine PWB memory (RAM) Turn the power switch off and on If not corrected, replace the main/
engine PWB.

Expansion memory (DIMM) Replace the expansion memory (DIMM)

Error Codes List page 10

page

Code: F040

Description:

Main/engine PWB engine communication error

Remedy:

Main/Engine PWB Turn the power switch off and on If not repaired, replace the EEPROM on the
main/engine PWB or main/engine PWB.

Code: F041

Description:

Main/engine PWB - Scanner PWB communication error

Remedy:

Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.

Code: F050

Description:

Main/engine PWB engine checksum error

Remedy:

Main/Engine PWB Download the engine firmware again (TSI: see page 4-138,LCD: see page 4- 141)

Main/Engine PWB Turn the power switch off and on If not repaired, replace the EEPROM on the
main/engine PWB or main/engine PWB.

Code: F051

Description:

No scan engine main program

Remedy:

Main/Engine PWB Turn the power switch off and on If not corrected, replace the main/ engine PWB.
Code: F12X

Description:

Abnormality detecting in a Scan control section

Remedy:

(1) Check the harness between Scan/DP<=>Main/Engine PWBs, and the connection state of a connector,
and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation
check is performed. (3) Exchange a Scan/DP board and perform an operation check. (4) Exchange a
Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.

Code: F14X

Description:

Abnormality detecting in a FAX control part

Remedy:

(1) Check the harness between FAX<=>Main/Engine PWBs, and the connection state of a connector, and
perform an operation check. (2) U021 Controller backup initialization is carried out and an operation
check is performed. (3) Perform a deed operation check for DIMM Clear by U671. * Notes(Since it
disappears when received data remain, cautions are required.) (4) Exchange a FAX board and perform
an operation check. (5) Exchange a Main/Engine PWB and perform an operation check. (6) Get USBLOG
and contact service headquarters.

Error Codes List page 11

All About this machine Error Code:

page

Code: F15X

Description:

Abnormality detecting in an authentication device control section

Remedy:

(1) Check the harness between authentication device <=>Main/ Engine PWBs, and the connection
situation of a connector, and perform an operation check. (2) Carry out U021 Main backup initialization
and perform an operation check. (3) Exchange a Main/Engine PWB and perform an operation check. (4)
Get USBLOG and contact service headquarters.

Code: F18X

Description:

Abnormality detecting in a Video control section

Remedy:

(1) Check the harness between Engine<=>Main/Engine PWBs, and the connection state of a connector,
and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation
check is performed. (3) Exchange a Main/Engine PWB and perform an operation check. (4) Get USBLOG
and contact service headquarters.

Code: F1DX

Description:

Abnormality detecting of the image memory Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F21X, F22X, F23X

Description:

Abnormality detecting in an image-processing part

Remedy:

(1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup
initialization and perform an operation check. (3) Exchange a Main/Engine PWB and perform an
operation check. (4) Get USBLOG and contact service headquarters.

Code: F24X

Description:

Abnormality detecting in the system Management Department

Remedy:
(1) Check contact of a DDR memory and perform an operation check. (2) Carry out U021 Main backup
initialization and perform an operation check. (3) Exchange a Main/Engine PWB and perform an
operation check. (4) Get USBLOG and contact service headquarters.

Code: F25X

Description:

Abnormality detecting in a network management department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and packet capture and contact
service headquarters.

Error Codes List page 12

All About this machine Error Code:

page

Code: F26X ... F2AX

Description:

Abnormality detecting in the system Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F2BX ... F32X

Description:

Abnormality detecting in a network control part

Remedy:
(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.
(Depending on an analysis result, it is packet capture acquisition)

Code: F33X

Description:

Abnormality detecting in the Scan Management Department

Remedy:

(1) Check the harness between Scan/DP<=>Main/Engine PWBs, and the connection state of a connector,
and perform an operation check. (2) U021 Controller backup initialization is carried out and an operation
check is performed. (3) Exchange a Scan/DP board and perform an operation check. (4) Exchange a
Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.

Code: F34X

Description:

Abnormality detecting in the Panel Management Department

Remedy:

(1) Check the harness between Panel<=>Main/Engine PWBs, and the connection state of a connector,
and perform an operation check. * Notes (2) U021 Controller backup initialization is carried out and an
operation check is performed. (3) Exchange a Panel board and perform an operation check. (4) Exchange
a Main/Engine PWB and perform an operation check. (5) Get USBLOG and contact service headquarters.

Code: F35X

Description:

Abnormality detecting in the printing controlling Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F37X

Description:

Abnormality detecting in the FAX Management Department

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Error Codes List page 13

All About this machine Error Code:

page

Code: F38X

Description:

Abnormality detecting in the authentication authorized Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F3AX ... F45X

Description:

Abnormality detecting in the Entity Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F46X

Description:

Abnormality detecting of a printer rendering part

Remedy:
(1) Exchange a Main/Engine PWB and perform an operation check. (2) the acquisition wish of USBLOG --
carry out (Depending on the (2) case, it is print capture data acquisition)

Code: F47X, F48X, F49X

Description:

Abnormality detecting of an image editing processing part

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F4DX, F4EX

Description:

Abnormality detecting in the Entity Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F4FX

Description:

Abnormality detecting in the JOB Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Kyocera ECOSYS M2040dn

All About this machine Error Code:

page

Code: F50X

Description:

Abnormality detecting in the FAX Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F51X ... F57X

Description:

Abnormality detecting in a JOB execution part

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F58X ... F5EX

Description:

Abnormality detecting in the various-services Management Department

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F5FX

Description:

Abnormality detecting in a service execution part

Remedy:
(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F62X

Description:

Abnormality detecting in a service execution part

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Code: F63X

Description:

Abnormality detecting in a device control section

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

PrintCopy.info service

Search by model Kyocera

Catalog Sign In Contacts Forum Eng

USD 0.00

Discount 0.0%

Parts List 0
Error Codes

Kyocera

ECOSYS M2040dn

All codes

Kyocera ECOSYS M2040dn

Error Codes List page 15

All About this machine Error Code:

page

Code: F69X ... F6CX

Description:

Abnormality detecting in a HyPAS-E part

Remedy:

(1) Carry out U021 Main backup initialization and perform an operation check. (2) Exchange a
Main/Engine PWB and perform an operation check. (3) Get USBLOG and contact service headquarters.

Error Code

Parts Catalog

Service Mode, Troubleshooting

Downloads Files

Used abbreviations

Compatibility

Discounts

Payments

Privacy, Terms, Refunds

Total in database

Brands: 24
Models: 8626

Kyocera: 438

PrintCopy .info service 2001 - 2025