Advanced Engineering Materials

2.8.1. V-I CHARACTERSTICS AND WORKING OF TUNNEL DIODE

Fig. 2.11: V-I characteristics of tunnel diode

 As a forward voltage across the tunnel diode is increased from zero, electrons from N
region ‘tunnel’ through potential barrier to the P region. As a result, diode current
increases until the peak point ‘P’ is reached. Till then the diode exhibits positive
resistance.
 As the voltage is increased beyond VP, the tunneling action starts decreasing & diode
current decreases till valley point ‘V’ is reached. In the region between peak point &
valley point current decreases and the diode shows negative resistance (i.e., When the
forward bias is increased, the current decreases).
 When forward bias is increased beyond valley point voltage V v , the tunnel diode behaves
as a normal diode. The diode current increases with increase in forward voltage.

2.8.2. APPLICATIONS OF TUNNEL DIODE

 When operated in the negative resistanceregion, they can be used as oscillator.

 They are used in low power amplifiers.
 They can be used as switching device in computers.
 Since tunnel diodes are more resistant to nuclear radiation, they are used in space applications
like amplifiers for satellite communications.

QUE: Explain V-I characteristics of tunnel diode. (3)[Winter-12]

QUE: What is tunnel diode, draw and explain its V-I characteristics.

2.9 PHOTO DIODE

 A photodiode is a type of light detector, used to convert the light energy into electrical
energy (current or voltage) based on the mode of operation of the device.
 It is also called as light sensor.
 Typical photodiode materials are Silicon, Germanium, Indium Gallium Arsenide
Phosphide and Indium gallium arsenide.
 The symbol of the diode is shown in fig,2.12.

11
 Advanced Engineering Materials

Fig.2.12: Symbol of photodiode

2.9.1. V-I CHARACTERISTICS AND WORKING OF PHOTODIODE:

Fig.2.13: Working Principle of photodiode

 The Photodiode works in reverse bias mode.

 In this mode, the depletion region has large width.
 When reverse biased is applied to the diode, a small amount of current due to minority
charge carriers is produced.
 This current is obtained without the incidence of light radiation and hence called as
leakage current or dark current.
 Working Principle: When light photons of sufficient energy h  Eg are incident on
the depletion layer, electrons and holes are generated. This mechanism is called the inner
photoelectric effect.
 A photon of energy hv ≥ Eg incident in or near the depletion layer of the diode will excite
an electron from the valence band to the conduction band. This process generates a hole
in the valence band. Thus, an electron-hole pair is generated by the optical photon. These
are known as photocarriers.
 The electron-hole pairs generated in the depletion layer separates and drift in opposite
directions under the action of the electric field. Such a transport process induces an
electric current in the external circuit in excess of the already existing dark current
(reverse leakage current).
 If the absorption of light takes place in the depletion region, then the charge carriers are
removed from the junction by the inbuilt electric field of the depletion region.
 Therefore, the holes move towards the cathode, and electrons move towards the anode,
and a photocurrent is generated as shown in fig.2.13. Optical excitation leads to an
increase in the reverse-biased current.
 The V-I characteristics of photodiode is shown in fig.2.14.
 This current depends upon the intensity of incident radiation.

12
 Advanced Engineering Materials

 Photocurrent is proportional to the incident light intensity. The amount of photocurrent

generated increases as light intensity (IL) increases.
 The total current through the diode is the sum of dark current and photocurrent.
 To maximize the sensitivity of photodiode we need to minimize the dark current.
 It is desirable that the depletion region be sufficiently wide so that a large fraction of
incident light can be absorbed. Therefore, the diode can be used as a photo detector—
using a reverse bias voltage—as the measured photocurrent is proportional to the incident
light intensity.

Fig.2.14: V-I characteristics of photodiode

Modes of Operation:
The operating modes of the photodiode include three modes, namely Photovoltaic mode,
Photoconductive mode, an avalanche diode mode.
Photovoltaic Mode:
 In this mode, the diode is not connected to power source. We do not bias the diode.
 When the light falls in such condition on the photodiode, it excites the electrons to higher
energy state and results in electrons to move towards cathode terminal and holes towards
anode terminal. This process creates a potential difference between two terminals.
Photoconductive Mode:
 In photoconductive mode, the diode is connected to the power source and diode is reverse
biased.
 The reverse voltage application will increase the depletion layer’s width.
 When the light falls on the photodiode creates a pair of electrons and holes which move
in the opposite direction due to biased voltage.
Avalanche Diode Mode:
 An Avalanche photodiode is operated at reverse bias close to the breakdown voltage.
 When reverse-biased, there is a creation of strong fields in the junction region.
 When a photon generates an electron-hole pair, the pair flows through the junction.
Because of the strong fields in the junction, the electron gains enough energy to cause
ionisation of neutral atoms and secondary electrons and holes are generated.
 Thus, a multiplication (or avalanche) process takes place (hence the name), and a
substantial current is generated from few initial photons as shown in fig.2.15.
 The avalanche photodiodes are good for those optical systems where intensity of
incoming light signal is very low.

13
 Advanced Engineering Materials

Fig.2.15: Avalanche photodiode

2.9.3 APPLICATIONS:

We can use the photodiode in

 smoke detectors to sense smoke and fire,
 a solar panel as solar cells,
 barcode scanner for character recognition,
 the obstacle detection system,
 printers as page presence and page counter,
 Optical message transmission,
 Fibre optics-based communication network as photo detector.
 It is also used as Position sensor.

2.10 LIGHT EMITTING DIODE(LED)

 LED is a specially made forward biased P-N junction diode, which emits light due to
electron-hole recombination, when energized.
 This works on the principle of electroluminescence, the process in which electrical energy
is converted into light energy.
 Henry Joseph Round was the first person to observe the phenomenon of
electroluminescence in 1907 and invent the first LED.
 It is operated only in forward bias.
 The symbol of LED is shown in Fig. 2.16.

Fig. 2.16:Symbolic representation of LED

14
 Advanced Engineering Materials

2.10.1. V-I CHARACTERSTICS AND WORKING OF LED

Fig. 2.17(a): Working of LED diode Fig. 2.17 (b): V-I characteristics of LED

 When Light Emitting Diode (LED) is forward biased, the free electrons from N-side and
the holes from P-side move towards the junction as shown in fig.2.17(a)
 Like ordinary diode, the forward current is negligible up to a certain value of forward
applied voltage due to the potential barrier across the PN-junction.
 When free electrons reach the junction, they overcome the potential barrier and
recombine with the holes.
 In the similar way, holes from p-side recombine with electrons in the depletion
region. Because of the recombination of free electrons and holes in the depletion region,
the width of depletion region decreases.
 The recombination of free electrons and holes leads to generation of light.
 The wavelength of light emitted and its color depends on Energy Gap(Eg) of material
used in making of LED.
 The wavelength of light emitted = where = ℎ = . For light to be emitted in
visible region, Energy gap should be between 1.77eV to 3.11eV.
 Silicon and Germanium have bandgap energies that correspond to infrared light which is
not visible. Energy gap of Silicon is 1.1eV and that of Germanium is 0.72eV. They are
known as indirect- bandgap semiconductors. This means, it is not possible for electrons
and holes to recombine directly and form a photon. Instead, you get a phonon (type of
lattice vibration) which is effectively heat.
 An LED requires a direct- bandgap semiconductors having Energy gap ≥ 1.8eV.This can
happen very efficiently in materials like Gallium Arsenide Phosphide (GaAsP) =
1.9eV and Gallium Phosphide (GaP) = 2.26eV.The Energy released in these materials
produces intense visible light.
 The V-I characteristics of LED is shown in fig. 2.17(b).When the voltage applied
overcomes the Energy gap(potential barrier), current increases rapidly as more number of
charge carriers cross the PN junction. This voltage above which the diode starts
conducting is called cut-in voltage of LED.
 The voltage after cut-in value remains almost constant once LED starts conducting like
ordinary diode, but current increases rapidly.

2.10.2. APPLICATIONS OF LIGHT EMITTING DIODE

 LEDare commonly used as indicator in electronic circuits.
 They are used in electronic calculators to display the numbers.

15
 Advanced Engineering Materials

 They are used in digital meters & electronic clocks.

 Infrared LEDs can be used as a source in optical fiber communications.
 LEDs are used in Burglar alarms systems, Calculators, Picture phones, Traffic signals, Digital
computers, Microprocessors, Digital watches, Automotive heat lamps, Camera flashes and
Aviation lighting.

2.10.3 ADVANTAGES OVER FILAMENT LAMPS

 Low operational voltage and less power is required to operate.

 Fast action and no warm-up time required.
 Long life.
 Fast on-off switching capacity.
 Emits monochromatic light.
 Smaller in size and lighter in weight.

QUE: What is LED? Draw and explain its V-I characteristics.

2.11. TRANSISTORS
 Transistor was invented in 1947 by American Physicists Bardeen, Brattain and Schockley
at Bell Telephone laboratories.
 A transistor is a semiconductor device that contains three regions separated by two
distinct PN junctions. The two junctions are EB junction and CB junctions.
 The central region is called base.
 The two outer regions are called emitter and collector.
 There are two types of charge carriers, electrons and holes hence transistor is called
bipolar transistor.
 Transistor can be viewed as two PN junction diodes arranged back-to-back with base
being common to both the diodes.
 As soon as the two junctions are formed, majority charge carriers diffuse and form two
depletion layers. Depletion layer is narrow at EB junction and wide at CB junction.

QUE : What is a transistor ? (1)[Winter-18]

There are two types of transistors:

1.NPN transistor--P-type sandwiched between two N-type.
2.PNP transistor--N-type sandwiched between two P-type.

16
 Advanced Engineering Materials

Fig.2.18: Block diagram and Symbolic representation of NPN & PNP transistor

2.11.1 FUNCTIONS OF THREE REGIONS IN TRANSISTOR:

Emitter, Base and Collector are three regions in a transistor.
Emitter:
 It emits charge carriers.
 It is heavily doped and has moderate size.
 It is located at the one end of transistor.
Base:
 The base controls the flow of charge carriers from emitter to the collector. Therefore, it
acts as a gate between emitter and collector.
 It has minimum thickness and is lightly doped.
 It makes the central region of a transistor.
Collector:
 It collects the charge carriers coming from the base.
 It has largest size with moderate doping. It is moderately doped.
 It is at the other end of a transistor.

2.11.2Biasing of transistor

 The Emitter-Base (EB) junction of transistor is always forward biased, and Collector-
Base (CB) junction of transistor is always reverse biased.
 Therefore, it works in an active mode. Hence, it transfers current from low resistance
region (EB) to high resistance region (CB).
 It is seen that almost same current flows through the two junctions.
 Thus, the device is called as transistor- the shortened form of transfer resistor.

2.11.3. EXPLAIN WHY:

Base region is lightly doped:

 If base region is heavily doped, more holes would be present in the base (for NPN
transistor).
 The incoming electrons would then undergo more recombination with holes in base.
 This would decrease the no. of electrons entering the collector region.
 Hence the collector current will decrease and base current will increase.
 But in transistor circuits, more collector current and less base current is required.
 Hence to minimize base current base region is lightly doped.

17
 Advanced Engineering Materials

Base region is narrow:

 The main function of the base is to control the number of charge carriers from emitter to
collector and hence offers easy and quick diffusion of carriers into collector region.
 If the width of the base is more, then it would lead to more number of recombination
causing an increase in base current.
 But in transistor circuits, more collector current and less base current is required.
 Hence to offer quick diffusion of charge carriers and to keep base current to a minimum
amount, the base region is made narrow.

Emitter is heavily doped:

 The main function of the transistor is to emit charge carriers.
 In transistor circuit it is required that a maximum number of majority carriers are injected
into the base so that the emitter current IE will be large.
 Hence to provide large no. of charge carriers emitter is heavily doped as compared to base
and collector.

Collector region is larger:

 The main function of collector is to collect all the charge carriers coming from base.
 Due to the movement of minority charge carriers across the reverse biased collector base
junction, large amount of heat is produced as the minority charge carriers acquire large
amount of kinetic energy.
 Hence to collect all the charge carriers and to dissipate away the heat, the collector region
is made larger.

QUE: Explain why in a transistor (i) The base is thin and lightly doped (ii) The collector
is large in size. (2)[Winter-12, 15]
QUE : Why the base region is thin and lightly doped in a transistor? Explain.
(3)[Winter-16]
QUE: Explain the function of emitter, base and collector in a transistor.
(3)[Winter-12, Summer-18]
QUE:Explain whythe emitter is heavily doped? (1) [Winter-18]

2.12 CIRCUIT CONFIGURATION

COMMON BASE CONFIGURATION:

Fig.2.19: Transistor in common base configuration

In this circuit, Base terminal is made common to both input and output circuits.

18
 Advanced Engineering Materials

COMMON EMITTER CONFIGURATION:

Fig.2.20: Transistor in common emitter configuration

In this circuit, Emitter terminal is made common to both input and output circuits.

COMMON COLLECTOR CONFIGURATION:

Fig.2.21: Transistor in common collector configuration

In this circuit, collector terminal is made common to both input and output circuits.

2.13. TRANSISTOR ACTION

Fig.2.22 (a): Working of Transistor in common base mode

19
 Advanced Engineering Materials

Fig.2.22 (b): Working of Transistor in common base mode

1. Consider an NPN transistor biased by using two batteries VEE & VCC as shown in
fig.2.22The emitter base junction is kept at forward biased by battery VEE & collector
biased junction is kept as reverse biased junction by battery VCC.
2. As emitter base junction is forward biased the electron from emitter (E) moved towards
base (B) & holes from base (B) moves towards emitter (E). Since emitter is highly doped
& base is lightly doped, the emitter current IE is practically due to electron moving from
emitter to base.
3. On entering the base region, electrons recombine with small no. of available holes in the
base region, causing base current IB. Since the base region is light doped, the
recombination is very less & hence IB is very less.
4. The electrons experience a very strong electric field due to reversed biased CB junction &
get swept into the collector region. This constitutes collector current IC. Maximum number
of electrons flow from emitter into the collector. This is possible due to light doping &
small size of base region.
5. The total emitter current IE is given by I =I +I ---------- (1)
E B C

2.14APPLICATIONS OF TRANSISTOR
 It is used in switching electronic circuits.
 It is used as an amplifier.
 It is used in integrated circuits.

2.14.1Application of Transistor as amplifier

Transistor can work in three different regions like active region, cutoff region & saturation
region. They are turned off while working in the cut-off region and turned on while working
in the saturation region. Transistors work as an amplifier when they work in the active region.
The main function of a transistor as an amplifier is to enhance the input signal. The input of
the amplifier is a voltage otherwise current, where the output will be an amplified input
signal.

I. Common Emitter transistor amplifier:

A transistor in which the emitter terminal is made common for both the input and the output
circuit connections is known as common emitter configuration. When this configuration is
provided with alternating current (AC) supply and operated in between both positive and the
negative halves of a.c. cycle to generate the specific output signal is known as common
emitter amplifier. In this type of configuration, the input is applied at the base terminal and
the output is to be collected across the collector terminal. Emitter terminal is common in both
the cases of input as well as output as shown in fig.2.23.

20
 Advanced Engineering Materials

Fig.2.23: Common Emitter Transistor Amplifier

In this circuit, the Emitter Base junction is forward biased using base - emitter battery VEB
and collector -Base junction is reverse biased using collector - emitter battery Vcc. The low
input signal is applied to the emitter-base junction and the amplified output is obtained across
the Rc load connected in the collector circuit. The collector current is controlled by base
current. When input signal is applied to the base, very small change in base current produces
very large changes in collector current. Therefore, the current gain is substantially high.

a) D.C current Gain: It is the ratio of collector current to base current. It is denoted by
‘β’.

∴ . , = --------------- (1)
b) A.C current Gain: It is the ratio of change in collector current to change in base
current. It is denoted by ‘βac’.

∆
∴ . , = --------------- (2)
∆

The value of β is between 20 to 500.

c) A.C. Voltage Gain: It is the ratio of the a.c output voltage to a.c. input voltage. It is
denoted by AV.

∴ . , = = =-β ---------------- (3)

where RB is the input resistance.

The negative sign indicates that the output voltage is opposite with the phase of input
voltage.

d) Power gain
The power gain Ap is the product of the current gain and voltage gain.

Ap = βac * Av
The power gain is also defined as the ratio of change in output power to the change in
input power.

21
 Advanced Engineering Materials

II. Common base transistor Amplifier:

In common base configuration, emitter is the input terminal, collector is the output terminal
and base terminal is connected as a common terminal for both input and output.

Fig.2.24:Common Base Transistor Amplifier

Fig.2.24 shows NPN transistor connected in Common Base configuration. The transistor is
biased to operate in the active region. The battery VEE forward biases the EB junction and the
battery VCC reverse biases CB junction. As signal source Vi is connected to input circuit and a
load resistance RL is connected in output circuit. An output voltage Vo is developed across RL.
The input circuit has a low resistance. Hence a small change in the signal voltage will cause a
significant change in the collector current due to transistor action. Thus, a large voltage drop
occurs when collector current flows through load resistor. Hence a weak signal applied in
input circuit gets amplified in the collector circuit. The output voltage is in phase with
the input signal.

a) Current gain (amplification factor): The ratio of the change in the collector current
to the change in the emitter current at constant collector to base voltage (VCB) is
called the current amplification factor α.

22
 Advanced Engineering Materials
∆
= ∆
--------------- (5)

The value of the current amplification factor α is always less than 1.The typical current gain
of a common base amplifier is 0.98.
b) Voltage Gain (G): It is the ratio of output signal voltage to input signal voltage.

= -------------- (6)

The emitter current variation ∆ due to emitter-base voltage variation is taken as

∆ = ---------------- (7)
The change in collector current ∆ due to variation in emitter current ∆ is given by

∆ = ∆ ----------------- (8)

This current ∆ causes a voltage drop, =∆ = ∆ =α

∆
∴ = = =α
∆

= as α ≅ 1

is order of kilo- ohms, hence >> .Therefore, is larger than indicating that the
transistor amplifies a small input voltage to large output voltage.

2.14.2Relation between α and β:

∆ ∆
= and =
∆ ∆

Since = +

∆ =∆ +∆

∆ ∆ ∆
Dividing by ∆ , = +
∆ ∆ ∆

∆ ∆
= +1
∆ ∆

or = +1=

= +1

= or = ( = − 1=

=1− , = )

23
 Advanced Engineering Materials

2. To determine the sign of charge carriers.

3. To determine the charge carrier concentration.
4. To determine the mobility of charge carriers if conductivity of the material is known.
5. To measure variable magnetic fields up to frequency of 1012Hz.
6. To measure extremely heavy currents, where conventional ammeter cannot be used.

2.15.7. EFFECT OF TEMPERATURE ON HALL COEFFICIENT

 In metals, Hall coefficient does not depend on temperature.
 Hence concentration of free electrons does not vary with temperature.
 In semiconductors, Hall coefficient decreases with the rise in temperature.
 Thus, the concentration of free electrons increases with temperature.

1.14.8. SIGNIFICANCE OF HALL EFFECT

 Hall Effect experiment showed that it is the negative charge carriers namely electrons are
responsible for electrical conduction in metals.
 It also showed that there exist two types of charge carriers in semiconductors.

QUE : Explain Hall effect and its significance. Give its application. (5)[Summer-07]
QUE : What is Hall effect ? What are its applications? What is the effect of temperature on Hall
coefficient for semiconductors? (6) [Summer-09]
QUE : Explain Hall effect and its importance. (3)[Summer-05, Winter-11]

List of formulae:

1.Hall voltage VH = RH = where ‘t’ = thickness of sample.

2.Hall coefficient RH = − for N-Type and RH = forP-Type.
where ‘n’ or ‘p’ = Electron or hole (carrier) concentration.
3.Drift velocity = E or
4.Drift velocity =
5. Hall mobility = RH σ and w= width of the sample.
6. Hall Angle = tan ( ).
7.Current gain (CB mode) α = .

8. Current gain (CE mode) β = .

9.Emitter current = + .

10. Collector current, IC =

Solved Problems:
1. In Hall coefficient experiment a current of 0.25 A (2.5mA) is sent through a metal strip
having thickness 0.2 mm and width 5 mm. The Hall voltage is found to be 0.15 mV when a

28
 Advanced Engineering Materials

magnetic field of 2000 Gauss or 0.2 T is used. Calculate (a) carrier concentration (b) drift
velocity of the carriers. (4)[Summer-
03,07,08,10 &13]

Ans. Given: I = 0.25A,

thickness t= 0.2mm= 0.2×10-3m,
w= 5mm= 5×10-3m,
VH = 0.15mV=0.15×10-3V.
B =2000Gauss = 2000×10-4T.
n=? and =?
× × .
Solution: VH= = × . × × . ×

× × .
or 0.15 × 10 = × . × × . ×
× .
Hence Carrier concentration ‘n’ = = 1.04 × 10 /
. × × . × × . ×

. ×
Drift velocity = = = 0.15m/s.
× × ×

2.The resistivity of doped silicon crystal is 9.27 ×10-3 ohm-m and Hall coefficient is 3.84 ×10-4
m3/C. Assuming that the conduction is by a single type of charge carrier, calculate the
density (carrier concentration) and mobility of carriers. (4)[Winter-09,12 &17, Summer-09]
Ans.
Given: Resistivity ρ = 9.27 ×10-3 ohm-m,
Hall coefficient RH = -3.84×10-4 m3 /C,
Density (carrier concentration) n =?
Mobility of carriers μ=?
Solution:
Density (carrier concentration) = n= = = 1.6 × 1022/m3.
. × × . ×
. ×
= Hall mobility = RH σ = = = 0.0414 m2 /V.s.
. ×

3. A specimen of a semiconductor is 1mm thick and 1cm wide. A magnetic flux density of
0.5 T is applied parallel to 1mm edge and Hall voltage contacts are attached to measure the
voltage across the width of the sample. The current flowing length –wise through the sample
is 10mA.If the Hall coefficient of the material is 3.66×10-4m3 /C, compute the voltage between
the Hall contacts. ii) If the resistivity of the material is 8.93×10-3Ω.m, find the Hall angle.
Ans.
Given: Thickness‘t’= 1mm =10-3m,
width ‘w’=1cm=0.01m,
B=0.5T,
I =10mA= 10×10-3A,
RH = 3.66×10-4m3/C,
ρ= 8.93×10-3Ω.m,
find Hall voltage
. × ×
Solution: VH = RH = 3.66×10-4 = 1.86×10-4 volts.
θ = tan (μ B) = tan ( ) = tan (3.66 × 10 × × 0.5)
. ×
= tan (0.0205) =1.17o

4. An electric field of 100 V/m is applied to a sample of n-type semiconductor whose Hall
coefficient is -0.0125 m3/C. determine the current density in the sample assuming  e = 0.36
m2 /Vs. (3)[Winter-06]

29
 Advanced Engineering Materials

Ans.
Given: E=100V/m,
RH = 0.0125 m3/C,
e = 0.36 m2 /V.s
Find J.
. ×
Solution: Current density J = σE = = = 2880A/m2.
.
5. A specimen of a semiconductor is 1mm thick is placed in transverse magnetic field of 0.5T.
If the current flowing through the sample is 10mA, find (i) Hall angle(ii)Hall voltage if the
Hall coefficient of the material is 3.66x10-4 m3/C and the resistivity of the material is 8.93x10-
3
Ω.

Ans.

Given: t = 1 mm= 10-3m

w = 1 mm = 10-3 m
B = 0.5 T
I = 10 mA = 10 x10-3A
RH = 3.66x10-4 m3/C
ρ = 8.93x 10-3 Ω-m.
VH=?
θH=?
. ×
Solution:VH = RH = 3.66×10-4 = 1.83mV.
θ = tan (μ B) = tan ( ) = tan (3.66 × 10 × × 0.5)
. ×
= tan (0.0205) =1.17o
6. A semiconducting plate of thickness 2mm is placed in a magnetic field of 0.6 wb/m2
normal to its thickness. If the current of value 1.5x10-2A flows along its length, calculate the
Hall voltage if the Hall coefficient is 3.6x10-4 m3C-1.
Ans.
Given: t = 2 mm= 2x10-3m
B = 0.6 wb/m2
I = 1.5x10-2A
RH = 3.6 x10-4 m3/C
VH=?

. × . ×
Solution: VH = RH = 3.6×10-4 = 1.62 mV.
×

7.A semiconductor of width 4 mm is subjected to transverse magnetic field. The drift

velocity of electrons under this magnetic field is 3x103 m/sec. Calculate Hall voltage, if the
applied magnetic field is 4 Wb/m2.
Ans.
Given: w=4mm=4 x10-3 m
vd=3 x103m
B= 4 Wb/m2

: = = 4 × 3 × 10 × 4 × 10 = 48 V

30
 Advanced Engineering Materials

8. The Hall coefficient of certain silicon specimen is found to be -7.5×10-5 m3/C at a certain
temperature. If the conductivity is found to be 200mho/m, calculate density of charge
carriers and their mobility. (3M, W-2013)
Ans.
Given: Hall coefficient RH = -7.5×10-5 m3/C,
Conductivity = 200mho/m.
(1) n=? (2) μ =?
(1) RH = −
or n = −
=− = 8.32×1022/m3.
( . × × . ×

(2) = Hall mobility = RH σ

= 7.5 × 10 ×200mho/m
= 0.015 m2/V.s

___________________________________________________________________________

9. N-type germanium sample has a donor density of 1021 / m3. It is arranged in a Hall
experiment having magnetic field of 0.5 T and the current density is 500 A/m2. Find the Hall
voltage if the sample is 3 mm wide. (3M, S-2014)

Ans.

Given: n = donor density of 1021 / m3,

B= 0.5T,
Current density ‘J’= 500 A/m2,
width of sample ‘w’= 3mm = 3×10-3m.
Hall Voltage VH =?

RH = =
= =
or =
× × × .
= × . ×
= 4.68×10-3Volts= 4.68mV

10.Calculate the value of Hall angle for a given semiconductor from given data. RH = 3.66
×10-4 m3/C, ρ = 8.3 ×10-3 Ω-m, B= 0.5 Wb/m2. (2M, W-2012)

Ans.:
Given: RH = 3.66 ×10-4 m3 /C,
Ρ = 8.3 ×10-3 Ω-m,
B= 0.5 Wb/m2.
Hall angleθ =?
Hall angle θ = tan (μ B)
1
= tan ( )
ρ
= tan (3.66 × 10 × . ×
× 0.5)
= tan (0.02205)
=1.263o

31
 Advanced Engineering Materials

11. Find d.c. current gain for a PNP transistor in a common emitter mode if collector
current is 2mA and base current is 20μA. (3M, W-2016)
Ans.

Given: Ic = 2mA,
IB = 20μA,
β =?
Solution: β=

×
= ×
= 100.

12. In an NPN transistor in a common base configuration emitter current is 2mA and base
current is 20μA.What are the values of collector current and current gain?
(3M, W-2011, 2017)
Ans.:

Given: IE = 2mA,

IB = 20μA =20×10-3mA = 0.02mA,

(1) IC =? (2) α =?

Solution: (1) IC = IE -IB = (2-0.02) mA

= 1.98 mA
.
(2) α = = = 0.99

13.When a diode is forward biased a current of 50 mA flows through it. When it is reverse
biased the current drops to 20 nA. What is the ratio of forward to reverse current?

Ans.:
Given: Forward current, = 50 = 50 × 10
Reverse current, = 20 = 20 × 10
×
Solution: = = 2.5 × 10
×

14. A transistor is connected in the CE configuration. The collector supplies voltage of 10V
and the voltage drop across 500 ohms is 0.6V. If α = 0.96, find the (i) Collector-emitter
current (ii) emitter current (iii) base current.
Ans.
Given: VCC = 10 V
Voltage drops across collector VC = 0.6 V
RC = 500 ohms
Current gain = α = 0.96,
(1) VCE =? (2) IE =? (3) IB =?

Solution: i) VCE = VCC - VC = 10-0.6 = 9.4V

ii) α =

32
 Advanced Engineering Materials
.
Collector current, IC = = = 1.2

.
rIE = = = 1.25 mA
.
iii) IB = I E - IC = 1.25mA - 1.2 mA = 0.05mA.

15. For a transistor working as a common base amplifier, current gain is 0.96. If the emitter
current is 7.2mA, then calculate the base current.

Ans.
Givenα = 0.96
IE = 7.2mA
IB =?
IB =?
Solution: Current gain α = IC / IE
Therefore IC = αIE = 0.96 x7.2 = 6.91 mA

IB = IE – IC

IB= 7.2 mA - 6.91 mA

IB= 0.29 mA.

16. In a npn transistor circuit, the collector current is 15 mA. If 95% of the electrons emitted
by the emitter reaches the collector, what is the base current?

Ans.
Given: Collector current, IC = 15 mA
IC = 95% IE
IB=?
Solution: Since IC = 95% IE, IC = 0.95 IE
=
.
Since IE = IB + IC
Base current, IB = IE – I C
IB = IE – IC = . −
= − 15 = 0.79 mA
.
17.The base current of a transistor is 105 μA and collector current is 2.05 mA. Determine the
value of β, IE, and α. A change of 27 μA in the base current produces a change of 0.65 mA in
the collector current. Find βa.c.
Ans.
Given: IB = 105 μA =105 × 10-6 A,
IC = 2.05 mA = 2.05 × 10-3A
(1) IE =? (2) α =? (3) β =? (4) βa.c.=?

Solution: (1) IE = IB + IC
= (105 × 10-6 +2.05 × 10-3 ) A
= 2.155 × 10-3 A
(2) α = IC / IE= 2.05 × 10-3A /2.155 × 10-3A
= 0.95
(3) β = IC / IB = 2.05 × 10-3A /105 × 10-6 A
=19.52
(4) ΔIB = 27μA = 27 × 10-6 A
ΔIC = 0.65mA = 0.65 × 10-3 A
β = ΔIC / ΔIB = 0.65 × 10-3 A/27 × 10-6 A
=24.1

33
 Advanced Engineering Materials

18.A transistor has current gain factor α = 0.95. the transistor is connected in common-
emitter configuration. Calculate the change in collector current when the base current is
changed by 0.1 mA.
Ans.
Given: α = 0.95
Change in base current ΔIB = 0.1 mA
∆ =?
Solution: ΔIC = β ΔIB
But, =
∴ ∆ = ∆
0.95
∆ = (0.1) = 1.9
1 − 0.95
Question Bank

Q1. What is PN junction diode. Explain the characteristics of PN junction diode in forward and
reverse bias mode.
Q2. What do you understand by avalanche breakdown process in reverse bias PN junction diode?
Q3. What is rectification?
Q4. Explain how PN junction diode can be used as half wave rectifier.
Q5. What is bridge wave rectifier? Explain its working.
Q6. Explain the working of full wave rectifier.
Q7. What is the advantage of bridge rectifier over full wave rectifier?
Q8. How is half wave rectification different from full wave rectification, explain with the
help of diagram.
Q9. Draw circuit symbol of Zener diode.
Q10. What is Zener diode. Explain its VI characteristics in forward and reverse bias.
Q11. State the applications of Zener diode.
Q12. What is Zener breakdown process? Explain.
Q13. Write a note on LED.
Q14.What are uses and applications of LED?
Q15. Explain the construction and working of LED.
Q16. Why Silicon and Germanium cannot be used in fabrication of LED.
Q17. Draw V-I characteristics of photodiode. Explain dark current.
Q18.What is a photodiode. Explain its working principle.
Q19. What are the modes of operation of photodiode?
Q20. State the applications of photo diode.
Q21.Draw the circuit symbol of (1) Tunnel diode (2) Photodiode.
Q22.What is tunnel diode. Explain its working.
Q23.State the applications of tunnel diode.
Q24. Write short notes on
(a)Zener diode (b) Tunnel diode (c) LED (d) Photodiode
Q25.How does a transistor work as amplifier in Common base mode?
Q26. Define (1) current gain α (2) current gain β (3) Voltage gain Av.
Q27.Define Voltage gain Av in Common emitter and common base mode of an amplifier.
Q28. Give the relation between current gain α and β.
Q29. Explain the formation of energy bands in solids on the basis of band theory of solids.
Q.30 Distinguish between conductors, semiconductors and insulators.
Q.31 Prove that the probability function is symmetrical about EF at all temperatures except zero.
Q.32 Explain in brief the concept of Fermi energy. Derive an expression for Fermi energy in
intrinsic semiconductor.

34
 Advanced Engineering Materials

Q.33 Define Fermi level.

Q.34 Draw energy band diagram for N- type semiconductor at 0 K and T K.
Q.35 Draw energy band diagram for P- type semiconductor at 0 K and T K.
Q.35When donor impurities are added to a semiconductor, the concentration of holes decreases.
Explain with reasons.
Q.36 Distinguish between intrinsic and extrinsic semiconductors with suitable examples.
Q.37 Explain the detailed mechanism of current conduction in N-type and P-type semiconductors.
Q.38Explain Hall effect. Obtain an expression for Hall coefficient and density of charge carriers
for a P- type semiconductor.
Q.39 Explain the formation of potential barrier across the junction region of semiconductor diode.
Q.40 Explain the concept of diffusion current and drift current in a P-N junction diode.
Q.41 Draw the energy band diagram for symmetrically doped P-N junction when it is (i) Forward
biased (ii) Reverse biased.
Q.42 Explain why in a transistor: (i) Base is thin & lightly doped (ii) Collector region has large
area (iii) Emitter is heavily doped.
Q.43 Explain the action NPN and PNP transistor when operated in Common base mode.
Q.44 Explain the action NPN and PNP transistor when operated in Common emitter mode.
Q. 45 Explain the input and output characteristics of NPN transistor when operated in Common
base mode.
Q.46 Explain the input and output characteristics of NPN transistor when operated in Common
emitter mode.
Q.47 What is current gain in a transistor? Derive its relation for common base mode and common
emitter mode transistor.
Q.48 What is tunnel diode, draw and explain its V-I characteristics.
Q.49 What is Zener diode, draw and explain its V-I characteristics.
Q.50 What is LED? Which factor decides the colour emitted out of it. Draw and explain its V-I
characteristics.
Q.51. A strip of n-type germanium semiconductor of width 1mm and thickness 1mm has a Hall
coefficient 102m3/C.If magnetic field used is 0.1T and current through the sample is 1mA,
determine the Hall voltage produced and also find carriers concentration of electron.
(3M Winter-2015, Summer-2019)
(Ans. VH = 1mV, concentration of electron = n = 6.24X1016 /m3.)
Q.52. In Hall coefficient experiment a current of 2.5mA is sent through a metal strip having
thickness 0.2 mm and width 5 mm. The Hall voltage is found to be 0.15 mV when a magnetic field
of 200 Gauss is used. Calculate (a) carrier concentration (b) drift velocity of the carriers.
(3M, Summer-2016)(Ans. n= 1.04×1022/m3, vd = 1.5m/s.)
Q.53.Calculate the value of Hall voltage if observed Hall coefficient 5m3/C for a current of 1mA
flowing through a specimen of 20 mm thickness placed suitably in a magnetic field of flux density
1.0 Wb/m2. (3M, Summer-2018) (Ans. VH =0 .01 V)
Q.54. If the emitter current is 6 mA and collector current is 5.75mA, calculate the value of D.C.
current gain in common base mode. (3M, Summer-2018) (Ans. α = 0.958)
Q.55. In a common base connection, current amplification factor is 0.9. If the emitter current is
1mA, determine the value of base current. (Ans.0.1 mA)
Q.34.In a common base configuration, IC = 0.95 mA and IB = 0.05 mA. Find the value of α.
(Ans. 0.95)
Q.56.In a common base configuration, α = 0.95. The voltage drops across 2 kΩ resistance which is
connected in the collector is 2V. Find the base current. (Ans. 0.05 mA)

Q.57.Calculate IE in a transistor for which β = 50 and IB = 20 μA. (Ans.1.02 mA)

35