___________________

Preface

___________________
Application and properties 1

___________________
LEDs and connectors 2
SIMATIC NET
___________________
Installation, connecting up,
commissioning 3
S7-1200 - TeleControl
CP 1243-1 ___________________
4
Configuration

___________________
Program blocks 5
Operating Instructions

___________________
Diagnostics and upkeep 6

___________________
Technical data 7

___________________
Approvals A

___________________
Dimension drawings B

___________________
Documentation references C

04/2017
C79000-G8976-C365-03
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.

DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION
indicates that minor personal injury can result if proper precautions are not taken.

NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will
be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to
property damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions.
Qualified personnel are those who, based on their training and experience, are capable of identifying risks and
avoiding potential hazards when working with these products/systems.
Proper use of Siemens products
Note the following:

WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended
or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks
All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software
described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the
information in this publication is reviewed regularly and any necessary corrections are included in subsequent
editions.

Siemens AG C79000-G8976-C365-03 Copyright © Siemens AG 2014 - 2017.

Division Process Industries and Drives Ⓟ 05/2017 Subject to change All rights reserved
Postfach 48 48
90026 NÜRNBERG
GERMANY
Preface

Validity of this manual

This document contains information on the following telecontrol product:
● CP 1243-1
Article number 6GK7 243-1BX30-0XE0
Hardware product version 2
Firmware version V3.0
The CP 1243-1 is the communications processor for connecting the SIMATIC S7-1200 to
control center systems via the public infrastructure (e.g. DSL).
With the help of VPN technology and the firewall, the CP allows protected access to the
S7-1200.
The CP can also be used as an additional interface of the CPU for S7 communication.

Figure 1 CP 1243-1

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 3
Preface

Behind the top hinged cover of the module housing, you will see the hardware product
version to the right of the article number printed as a placeholder "X". If the printed text is, for
example, "X 2 3 4", "X" would be the placeholder for hardware product version 1.
You will find the firmware version of the CP as supplied behind the top hinged cover of the
housing to the left below the LED field.
You will find the MAC address under the lower hinged cover of the housing.

Product names and abbreviations

● CP / submodule / module
These abbreviations are used below instead of the full product name CP 1243-1:
● TCSB
This abbreviation ill be used below for the "TeleControl Server Basic", version V3.
● STEP 7
This short form will be used below for the STEP 7 Basic / Professional configuration tool.
● ES
PC with the STEP 7 project

Purpose of the manual

This manual describes the properties of this module and supports you when installing and
commissioning it.
The required configuration steps are described as an overview and there are explanations of
the relationship between firmware functions and configuration.
You will also find information about the diagnostics options of the device.

New in this issue

● New hardware product version 2
● New functions in the firmware version named above include:
– Expansion of the telecontrol protocols DNP3 and IEC
– Sending messages even without telecontrol communicaton
– Changed behavior during time-of-day synchronization, see section Time-of-day
synchronization (Page 42).
– Expansion of the supported data types, refer to the section Datapoint types (Page 89).
● Functional improvement of data point configuration as of STEP 7 V14 SP1. see section
Data point configuration (Page 82).
● Editorial revision

CP 1243-1
4 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Preface

Replaced manual issue

Edition 12/2016

Current manual release on the Internet

You will find the current version of this manual on the Internet pages of Siemens Industry
Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15922/man)

Required experience
To install, commission and operate the CP, you require experience in the following areas:
● Automation engineering
● Setting up the SIMATIC S7-1200
● SIMATIC STEP 7 Basic / Professional

Cross references
In this manual there are often cross references to other sections.
To be able to return to the initial page after jumping to a cross reference, some PDF readers
support the command <Alt>+<Left arrow>.

Sources of information and other documentation

You will find an overview of further reading and references in the Appendix of this manual.

License conditions

Note
Open source software
The product contains open source software. Read the license conditions for open source
software carefully before using the product.

You will find license conditions in the following document on the supplied data medium:
● OSS-CP1243-1_86.pdf

Firmware
The firmware is signed and encrypted. This ensures that only firmware created by Siemens
can be downloaded to the device.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 5
Preface

Security information
Siemens provides products and solutions with industrial security functions that support the
secure operation of plants, systems, machines and networks.
In order to protect plants, systems, machines and networks against cyber threats, it is
necessary to implement – and continuously maintain – a holistic, state-of-the-art industrial
security concept. Siemens’ products and solutions only form one element of such a concept.
Customer is responsible to prevent unauthorized access to its plants, systems, machines
and networks. Systems, machines and components should only be connected to the
enterprise network or the internet if and to the extent necessary and with appropriate security
measures (e.g. use of firewalls and network segmentation) in place.
Additionally, Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
Link: (http://www.siemens.com/industrialsecurity)
Siemens’ products and solutions undergo continuous development to make them more
secure. Siemens strongly recommends to apply product updates as soon as available and to
always use the latest product versions. Use of product versions that are no longer supported,
and failure to apply latest updates may increase customer’s exposure to cyber threats.
To stay informed about product updates, subscribe to the Siemens Industrial Security RSS
Feed under
Link: (http://www.siemens.com/industrialsecurity).

SIMATIC NET glossary

Explanations of many of the specialist terms used in this documentation can be found in the
SIMATIC NET glossary.
You will find the SIMATIC NET glossary on the Internet at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/view/50305045)

Recycling and disposal

The product is low in pollutants, can be recycled and meets the requirements of the WEEE
directive 2012/19/EU "Waste Electrical and Electronic Equipment".
Do not dispose of the product at public disposal sites. For environmentally friendly recycling
and the disposal of your old device contact a certified disposal company for electronic scrap
or your Siemens contact.
Keep to the local regulations.
You will find information on returning the product on the Internet pages of Siemens Industry
Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/view/109479891)

Training, Service & Support

You will find information on Training, Service & Support in the multi--language document
"DC_support_99.pdf" on the data medium supplied with the documentation.

CP 1243-1
6 Operating Instructions, 04/2017, C79000-G8976-C365-03
Table of contents

Preface ................................................................................................................................................... 3
1 Application and properties ..................................................................................................................... 11
1.1 Properties of the CP................................................................................................................11
1.2 Communications services .......................................................................................................11
1.3 Other services and properties .................................................................................................12
1.4 Security functions ....................................................................................................................13
1.5 Configuration limits and performance data .............................................................................15
1.6 Configuration examples ..........................................................................................................17
1.6.1 Sending e-mails ......................................................................................................................17
1.6.2 TeleControl Basic ....................................................................................................................18
1.6.3 DNP3 / IEC .............................................................................................................................20
1.6.3.1 Configuration with 1 subnet ....................................................................................................20
1.6.3.2 Configuration with connections over the Internet ...................................................................21
1.6.3.3 Configuration with a redundant control center ........................................................................22
1.7 Requirements for use..............................................................................................................23
1.7.1 Hardware requirements ..........................................................................................................23
1.7.2 Software requirements ............................................................................................................23
2 LEDs and connectors ............................................................................................................................ 25
2.1 Opening the covers of the housing .........................................................................................25
2.2 LEDs .......................................................................................................................................26
2.3 Electrical connectors ...............................................................................................................30
2.3.1 Power supply ..........................................................................................................................30
2.3.2 Ethernet interface X1P1 ..........................................................................................................30
3 Installation, connecting up, commissioning ............................................................................................ 31
3.1 Important notes on using the device .......................................................................................31
3.1.1 Notices on use in hazardous areas ........................................................................................31
3.1.2 Notices on use in hazardous areas according to IECEx / ATEX ............................................32
3.1.3 Notices regarding use in hazardous areas according to UL HazLoc .....................................33
3.1.4 Notices on use in hazardous areas according to FM .............................................................33
3.2 Installing, connecting up and commissioning .........................................................................34
3.3 Note on operation ...................................................................................................................36
4 Configuration ........................................................................................................................................ 37
4.1 Security recommendations .....................................................................................................37
4.2 Configuration in STEP 7 .........................................................................................................40
4.3 Addressing and authentication ...............................................................................................41
4.3.1 TeleControl Basic ....................................................................................................................41

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 7
Table of contents

4.3.2 DNP3 / IEC............................................................................................................................. 41

4.4 Time-of-day synchronization .................................................................................................. 42
4.5 Communication types ............................................................................................................ 45
4.6 Ethernet interface ................................................................................................................... 46
4.6.1 CP identification ..................................................................................................................... 46
4.6.2 Time-of-day synchronization .................................................................................................. 46
4.6.3 Advanced options .................................................................................................................. 47
4.6.4 Transmission settings – TeleControl Basic ............................................................................ 48
4.6.5 Transmission settings – DNP3 ............................................................................................... 49
4.6.6 Transmission settings - IEC ................................................................................................... 51
4.7 SNMP ..................................................................................................................................... 53
4.8 Partner stations ...................................................................................................................... 54
4.8.1 Partner stations > General parameters .................................................................................. 54
4.8.2 TeleControl Basic ................................................................................................................... 57
4.8.2.1 Addressing in the redundant TCSB system ........................................................................... 57
4.8.2.2 Advanced settings .................................................................................................................. 58
4.8.2.3 Partner for inter-station communication ................................................................................. 58
4.8.3 DNP3 / IEC............................................................................................................................. 59
4.8.3.1 Advanced settings (DNP3 / IEC)............................................................................................ 59
4.9 Security .................................................................................................................................. 63
4.9.1 Parameter overview ............................................................................................................... 63
4.9.2 CP iIdentifcation with the TeleControl Basic protocol ............................................................ 64
4.9.3 DNP3 security options ........................................................................................................... 65
4.9.4 Firewall ................................................................................................................................... 67
4.9.4.1 Pre-check of messages by the MAC firewall. ........................................................................ 67
4.9.4.2 Notation for the source IP address (advanced firewall mode) ............................................... 68
4.9.4.3 Firewall settings for configured connection connections via a VPN tunnel ........................... 68
4.9.4.4 Settings for online security diagnostics and downloading to station with the firewall
activated ................................................................................................................................. 68
4.9.5 E-mail configuration ............................................................................................................... 69
4.9.6 Log settings - Filtering of the system events ......................................................................... 70
4.9.7 SNMP ..................................................................................................................................... 70
4.9.8 Certificate manager ................................................................................................................ 72
4.9.9 Handling certificates ............................................................................................................... 72
4.9.10 VPN ........................................................................................................................................ 74
4.9.10.1 VPN (Virtual Private Network)................................................................................................ 74
4.9.10.2 Creating a VPN tunnel for S7 communication between stations ........................................... 76
4.9.10.3 VPN communication with SOFTNET Security Client (engineering station) ........................... 78
4.9.10.4 Creating the VPN connection telecontrol server .................................................................... 79
4.9.10.5 Establishment of VPN tunnel communication between the CP and SCALANCE M ............. 79
4.9.10.6 CP as passive subscriber of VPN connections ...................................................................... 79
4.9.10.7 SYSLOG ................................................................................................................................ 80
4.9.11 Configuration of the TeleService access ............................................................................... 80
4.10 Data points ............................................................................................................................. 82
4.10.1 Data point configuration ......................................................................................................... 82
4.10.2 Syntax of the data point names ............................................................................................. 88
4.10.3 Datapoint types ...................................................................................................................... 89
4.10.4 Configuration of the data point index ..................................................................................... 94
4.10.5 Status IDs of the data points .................................................................................................. 95

CP 1243-1
8 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Table of contents

4.10.6 Read cycle ..............................................................................................................................96

4.10.7 Process image, type of transmission, event classes, triggers ................................................97
4.10.8 "Trigger“ tab ..........................................................................................................................100
4.10.9 Threshold value trigger .........................................................................................................101
4.10.10 Analog value preprocessing .................................................................................................103
4.10.11 Command outputs .................................................................................................................109
4.10.12 Partner stations .....................................................................................................................112
4.10.12.1 Partner configuration for DNP3 and IEC data points ............................................................112
4.10.12.2 Partner configuration with TeleControl Basic data points. ....................................................112
4.11 Messages ..............................................................................................................................113
4.12 Access to the Web server .....................................................................................................115
5 Program blocks ................................................................................................................................... 117
5.1 Program blocks for OUC .......................................................................................................117
5.2 Changing the IP address during runtime ..............................................................................119
6 Diagnostics and upkeep ...................................................................................................................... 121
6.1 Diagnostics options ...............................................................................................................121
6.2 Online security diagnostics via port 8448 .............................................................................123
6.3 Online functions and TeleService .........................................................................................123
6.4 SNMP ....................................................................................................................................125
6.5 Processing status of e-mails .................................................................................................126
6.6 Downloading firmware ..........................................................................................................129
6.7 Module replacement .............................................................................................................132
7 Technical data .................................................................................................................................... 133
7.1 Technical specifications of the CP 1243-1............................................................................133
7.2 Pinout of the Ethernet interface ............................................................................................134
A Approvals............................................................................................................................................ 135
B Dimension drawings ............................................................................................................................ 139
C Documentation references .................................................................................................................. 141
Index................................................................................................................................................... 143

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 9
Table of contents

CP 1243-1
10 Operating Instructions, 04/2017, C79000-G8976-C365-03
Application and properties 1
1.1 Properties of the CP

Application
The CP is intended for operation in an S7-1200 automation system. The CP allows
connection of the S7-1200 to Industrial Ethernet or via the Internet to the following control
center systems:
● Telecontrol server (OPC server application TCSB V3)
● DNP3 master station
● IEC master station
With the combination of different security functions such as firewall and protocols for data
encryption, the CP protects the station and even entire automation cells from unauthorized
access and protects the communication between the remote S7 station and the master
station (TCSB) from espionage and manipulation.

1.2 Communications services

Communications services
The following communications services are supported:
● Telecontrol communication
The CP is a communications processor of the SIMATIC S7-1200 for system attachment
to the control center systems named above. The CP can communicate with redundant
control systems.
For each control center system the relevant telecontrol protocol is activated on the CP
("Type of communication"). The protocols allow IP-based data transmission for telecontrol
applications.
You will find the usable security functions in the section Security functions (Page 13).
● Messages / e-mail
With special events, the CP can send messages as e-mails.
You will find the requirements and functions in the section E-mail configuration (Page 69).
● S7 communication and PG/OP communication with the following functions:
– PUT/GET as client and server for data exchange with S7 stations
– PG functions
– Operator control and monitoring functions (HMI)

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 11
Application and properties
1.3 Other services and properties

1.3 Other services and properties

Other services and properties

● Data point configuration
Due to the data point configuration in STEP 7, programming program blocks in order to
transfer the process data is unnecessary. The individual data points are processed one-
to-one in the control system.
● IP configuration - IPv4 and IPv6
– IPv4 / IPv6
The CP supports IP addresses according to IPv4 and IPv6.
For telecontrol applications in IPv6 networks, an IPv6 address can be used in addition
to an IPv4 address.
– Address assignment
The IP address, the subnet mask and the address of a gateway can be set manually
in the configuration.
As an alternative, the IP address can be obtained from a DHCP server or by other
means outside the configuration.
● Time-of-day synchronization
The CP supports various methods of time-of-day synchronization. You will find
information in the section Time-of-day synchronization (Page 42).
For information on the format of the time stamp, refer to the section Datapoint types
(Page 89).
● Storage of events
The CP can store events of different classes chronologically and transfer them
spontaneously or together to the telecontrol server.
● Data transfer is on request or triggered
The telecontrol communication with the communications partner is triggered in two ways:
– After a request by the master or an OPC client connected to TCSB
– Unsolicited, triggered by various selectable criteria
● Analog value processing
Analog values can be preprocessed on the CP according to various methods.

CP 1243-1
12 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.4 Security functions

● Online functions / TeleService

From the engineering station you can access the station via the CP with the online
functions of STEP 7.
The following online functions are available:
– Downloading project or program data from the STEP 7 project to the station
– Querying diagnostics data on the station
– Downloading firmware files to the CP
For information on the online functions, refer to the section Online functions and
TeleService (Page 123).
● SNMP
As an SNMP agent, the CP supports data queries using SNMP (Simple Network
Management Protocol).
For more detailed information, refer to section SNMP (Page 125).

1.4 Security functions

Industrial Ethernet Security

With Industrial Ethernet Security, individual devices, automation cells or network segments
of an Ethernet network can be protected. The data transfer via the CP can be protected from
the following attacks by a combination of different security measures:
● Data espionage
● Data manipulation
● Unauthorized access
Secure underlying networks can be operated via additional Ethernet/PROFINET interfaces of
the CPU.
The security functions can be used independently of telecontrol communication.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 13
Application and properties
1.4 Security functions

Security functions of the telecontrol protocols

● TeleControl Basic
– Encrypted telecontrol communication
As an integrated (unconfigurable) security function, the protocol encrypts the data for
transfer.
You configure the interval of the key exchange between the CPU and telecontrol
server in STEP 7 in the parameter group "Ethernet interface (X1) > Advanced options
> Transmission settings".
– Telecontrol password
To authenticate the CP with the telecontrol server
● DNP3
The security functions specific to DNP3 can be used.
● IEC 60870-5
For the IEC protocol there are no protocol-specific security functions available.

Further configurable security functions of the CP

As a result of using the CP, as a security module, the following security functions are
accessible to the S7-1200 station on the interface to the external network:
● Firewall
– IP firewall with stateful packet inspection (layer 3 and 4)
– Firewall also for "non-IP" Ethernet frames according to IEEE 802.3 (layer 2)
– Limitation of the transmission speed ("Bandwidth limitation")
– Global firewall rules
● Communication made secure by IPsec tunnels (VPN)
VPN tunnel communication allows the establishment of secure IPsec tunnels for
communication with one or more security modules.
The CP can be put together with other modules to form VPN groups during configuration.
IPsec tunnels (VPN) are created between all security modules of a VPN group. All
internal nodes of these security modules can communicate securely with each other
through these tunnels.
● Logging
To allow monitoring, events can be stored in log files that can be read out using the
configuration tool or can be sent automatically to a Syslog server.
● STARTTLS / SMTPS
For the secure transfer of e-mails
● NTP (secure)
For secure transfer during time-of-day synchronization

CP 1243-1
14 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.5 Configuration limits and performance data

● SNMPv3
For secure transmission of network analysis information safe from eavesdropping
● Protection for devices and network segments
The protection provided by the firewall can cover individual devices, several devices or
even entire network segments.

Note
Plants with security requirements - recommendation
Use the following options:
• If you have systems with high security requirements, use the secure protocols
NTP (secure), HTTPS and SNMPv3.
• If you connect to public networks, you should use the firewall. Think about the services
you want to allow access to the station via public networks. By using the "bandwidth
limitation" of the firewall, you can restrict the possibility of flooding and DoS attacks.
See also section Security recommendations (Page 37).

For configuring the security functions refer to the section Security (Page 63).
You will find further information on the functionality and configuration of the security functions
in the information system of STEP 7 and in the manual /4/ (Page 142).

1.5 Configuration limits and performance data

Number of CMs/CPs per station

In each S7-1200 station, up to three CMs/CPs can be plugged in and configured; this allows
three CP 1243-1 modules.
To use telecontrol communication, three CP 1243-1 modules can be plugged in per station.

Connection resources
● Telecontrol connections
With the various telecontrol protocols the CP can establish connections to the following
master station types:
– To non-redundant or redundant telecontrol servers (TCSB).
– To up to four non-redundant or redundant DNP3 masters
– To up to four non-redundant or redundant IEC masters
With the Telecontrol Basic protocol, in addition to this, inter-station communication with
up to 15 S7 stations with a CP 1243-1 can be operated via the telecontrol server.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 15
Application and properties
1.5 Configuration limits and performance data

● S7 connections and TCP / UDP / ISO-on-TCP connections

Max. 14 connection resources, can be distributed as required for:
– S7 connections (PUT/GET)
– Connections via program blocks (OUC) to S7 stations
● Online functions
1 connection resource is reserved for online functions.
● PG/OP connections
– 1 connection resource for PG connections
– 3 connection resources for OP connections

Number of data points for the data point configuration

The maximum number of configurable data points is 200.

User data
The data to be transferred by the CP is assigned to various data points in the STEP 7
configuration.
The size of the user data per data point depends on the data type of the relevant data point.
You will find details in the section Datapoint types (Page 89).

Frame memory (send buffer)

The CP has a frame memory (send buffer) for the values of data points configured as an
event and that are sent to the communications partner.
The send buffer has a maximum size of 64000 events divided into equal parts for all
configured communications partners. The size of the frame memory can be set in STEP 7,
refer to the section SNMP (Page 53).
With the Telecontrol Basic protocol the send buffer can also be used for up to three partners
for inter-station communication You create the configuration in the "Partner" parameter
group.

Messages (e-mail)
● Sending of up to 10 messages (e-mails) can be configured with the message editor.
● Sending e-mails via the TMAIL_C program block

IPsec tunnel (VPN)

Up to 8 IPsec terminals can be established for secure communication with other security
modules.

CP 1243-1
16 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.6 Configuration examples

Firewall rules
The maximum number of firewall rules in advanced firewall mode is limited to 256.
The firewall rules are divided up as follows:
● Maximum 226 rules with individual addresses
● Maximum 30 rules with address ranges or network addresses
(e.g. 140.90.120.1 - 140.90.120.20 or 140.90.120.0/16)
● Maximum 128 rules with limitation of the transmission speed ("Bandwidth limitation")

1.6 Configuration examples

1.6.1 Sending e-mails

Configuration with sending of e-mails:

The following example shows a configuration with sending of e-mails. The telecontrol
communication of the CP is dsiabled.

Figure 1-1 Sending e-mails

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 17
Application and properties
1.6 Configuration examples

1.6.2 TeleControl Basic

Telecontrol with a non-redundant master station (TCSB)

Figure 1-2 Communication between S7 stations and a master station (TCSB)

In the telecontrol applications of the example shown, SIMATIC S7 stations communicate with
a non-redundant telecontrol server (TCSB) in the master station.
● Telecontrol communication between stations and master station
The communication is via the following paths and communications modules:
– Communication via the Internet: S7-1200 with CP 1243-1
– Communication via the GSM network and the Internet: S7-1200 with CP 1242-7 or
S7-200 with MODEM MD720
The establishment of terminal connections with encryption is initiated automatically by the
telecontrol protocol used by the various communications modules.
The creation of VPN connections between the CP 1243-1 and telecontrol server is
optional.
The telecontrol server monitors the connections established by the remote stations.
● Inter-station communication
Stations of the same type, for example S7-1200 with CP 1243-1, can communicate with
each other by sending the frames via the telecontrol server.

CP 1243-1
18 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.6 Configuration examples

Telecontrol with a redundant master station (TCSB)

The following figure shows a possible configuration with S7 stations communicating with a
redundant master station (TCSB).

Figure 1-3 S7 station communication with a redundant a master station

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 19
Application and properties
1.6 Configuration examples

1.6.3 DNP3 / IEC

1.6.3.1 Configuration with 1 subnet

Configuration example with a non-redundant control center

The following example describes a configuration with a non-redundant control center in
which all nodes are located in 1 IP subnet.
In this example, the DNP3 protocol is used; in other words, the stations are equipped with a
CP 1243-1.
A configuration in which the IEC protocol is used would have the same setup.

Figure 1-4 Configuration example with a non-redundant control center and stations in one IP subnet

The S7-1200 stations are connected to the Internet via the CP and connected to the control
center.
When using the DNP3 protocol, for example, SIMATIC PCS 7 TeleControl or the system of a
third-party provider can be used as the control center. If you use SIMATIC PCS 7
TeleControl as the DPN3 master in the control center, you require the necessary DPN3
driver.

CP 1243-1
20 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.6 Configuration examples

1.6.3.2 Configuration with connections over the Internet

Configuration example with connections over the Internet

The following example contains a configuration with a non-redundant control center.
In this example, the DNP3 protocol is used. A configuration in which the IEC protocol is used
would have the same setup.
The S7-1200 stations are connected to the Internet via the CP and connected to the control
center.
When using the DNP3 protocol, for example, SIMATIC PCS 7 TeleControl or the system of a
third-party provider can be used as the control center. If you use SIMATIC PCS 7
TeleControl as the DPN3 master in the control center, you require the necessary DPN3
driver.

Figure 1-5 Configuration example with connections over the Internet

As an alternative to the router SCALANCE 812, you can also use a standard DSL modem
and establish the VPN connection with a security module SCALANCE S.

Addressing
Refer to the information in the section DNP3 / IEC (Page 41).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 21
Application and properties
1.7 Requirements for use

1.6.3.3 Configuration with a redundant control center

Configuration example with a redundant control center

The following example contains a configuration with a redundant control center and
connections via the Internet.
In this example, the DNP3 protocol is used. A configuration in which the IEC protocol is used
would have the same setup.

Figure 1-6 Configuration example with a redundant DNP3 master station

Addressing of the redundant DNP3 master

The two devices of the redundant DNP3 master in the control center are addressed by the
CP using one DNP3 address but two different IP addresses.

CP 1243-1
22 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Application and properties
1.7 Requirements for use

1.7 Requirements for use

1.7.1 Hardware requirements

The following description relates to a configuration with telecontrol communication.
Rails, housing, cabling and other accessories are not taken into account.
Depending on the configuration of your plant, you require the following devices and firmware
versions.

Application example: Telecontrol communication with a control center

In the S7-1200 station:

● CPU with firmware version as of V3
The full functionality of the CP is only available with a CPU as of V4.2.
● DSL router SCALANCE M812

In the master station:

● PC with control center application (alternative):
– TCSB (version V3)
For more detailed information on the structure of TCSB , refer to the section /3/
(Page 142).
– DNP3 master
– IEC master
● DSL router SCALANCE M812
● When using online functions: Engineering station with STEP 7 (refer to the section
Software requirements (Page 23)).

For the configuration of the S7 station with CP:

Engineering station with STEP 7

1.7.2 Software requirements

Software for configuration and online functions

To configure and use the CP, the following configuration tool is required:
● STEP 7 Basic / Professional V14.0 SP1

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 23
Application and properties
1.7 Requirements for use

CP 1243-1
24 Operating Instructions, 04/2017, C79000-G8976-C365-03
LEDs and connectors 2
2.1 Opening the covers of the housing

Location of the display elements and the electrical connectors

The LEDs for the detailed display of the module statuses are located behind the upper cover
of the module housing.
The Ethernet connector is located behind the lower hinged cover of the module.

Opening the covers of the housing

Open the upper or lower cover of the housing by pulling it down or up as shown by the
arrows in the illustration. The covers extend beyond the housing to give you a grip.

Figure 2-1 Opening the covers of the housing

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 25
LEDs and connectors
2.2 LEDs

2.2 LEDs

LEDs of the module

The module has various LEDs for displaying the status:
● LED on the front panel
The "DIAG" LED that is always visible shows the basic statuses of the module.
● LEDs below the upper cover of the housing
The LEDs below the upper cover provide more detailed information on the module status.

Table 2- 1 LED on the front panel

LED / colors Name Meaning

DIAG Basic status of the module

(red / green)

Table 2- 2 LEDs below the upper cover of the housing

LED (color) Name Meaning

LINK Status of the connection to Industrial Ethernet

(green)
CONNECT Status of the connections to the communications partner

(green)
VPN Status of the VPN configuration

(green)
SERVICE Status of a connection for online functions

(green)

LED colors and illustration of the LED statuses

The LED symbols in the following tables have the following significance:

Table 2- 3 Meaning of the LED symbols

Symbol -

LED status OFF ON (steady light) Flashing Not relevant

CP 1243-1
26 Operating Instructions, 04/2017, C79000-G8976-C365-03
 LEDs and connectors
2.2 LEDs

Note
LED colors when the module starts up
When the module starts up, all its LEDs are lit for a short time. Multicolored LEDs display a
color mixture. At this point in time, the color of the LEDs is not clear.

Display of the basic statuses of the CP ("DIAG" LED)

Table 2- 4 Display of the basic statuses of the CP

DIAG Meaning
(red / green) (if more than one point listed: alternative meaning)
Basic statuses of the CP
• Power OFF
• Incorrect startup
Running (RUN) without serious error

green
• Partner not connected

flashing green • Firmware loaded successfully

• Starting up

flashing red • Module fault

• Invalid STEP 7 project data
Error loading firmware

flashing red-green

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 27
LEDs and connectors
2.2 LEDs

Display of the operating and communications statuses

The LEDs indicate the operating and communications status of the module according to the
following scheme:

Table 2- 5 Display of the operating and communications statuses

DIAG - LINK CONNECT VPN SERVICE Meaning

(red / green) (green) (green) (green) (green) (if more than one point listed: alternative
meaning)
Module startup (STOP → RUN) or error statuses
Power OFF

Startup - phase 1

red
- Startup - phase 2

flashing red
- - - - Running (RUN) without serious error

green
Incorrect startup

- - - Invalid STEP 7 project data

red
- - - Missing STEP 7 project data

flashing red
- - Backplane bus error

flashing red
Connection to Industrial Ethernet
- - - - Connection to Industrial Ethernet exists

- - - • Connection to Industrial Ethernet being

established.
green
• IP address being obtained.
- - - - No connection to Industrial Ethernet

Connection to communications partners

- - Connection established to at least one
partner
green
- - Partner reachable, CPU in STOP mode

green
- - Partner not reachable

flashing
green

CP 1243-1
28 Operating Instructions, 04/2017, C79000-G8976-C365-03
 LEDs and connectors
2.2 LEDs

DIAG - LINK CONNECT VPN SERVICE Meaning

(red / green) (green) (green) (green) (green) (if more than one point listed: alternative
meaning)
Connection for online functions
- - Connection for online functions established

green
- - Attempt to establish connection for online
functions
green
- - - No connection to engineering station

green
VPN connection
- - VPN connection established

green
- - VPN connection configured but not estab-
lished.
flashing flashing
green green
- - - - No VPN connection configured on the CP

Loading firmware
Loading firmware. The DIAG LED flashes
alternating red and green.
Firmware was successfully loaded.

flashing
green
Error loading firmware

flashing red

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 29
LEDs and connectors
2.3 Electrical connectors

2.3 Electrical connectors

2.3.1 Power supply

Power supply
The CM is supplied with power from the backplane bus. It does not require a separate power
supply.

2.3.2 Ethernet interface X1P1

Ethernet interface
The Ethernet connector is located behind the lower hinged cover of the module. The
interface is an RJ-45 jack according to IEEE 802.3.
The pin assignment and other data relating to the Ethernet interface can be found in the
section Technical data (Page 133).

CP 1243-1
30 Operating Instructions, 04/2017, C79000-G8976-C365-03
Installation, connecting up, commissioning 3
3.1 Important notes on using the device

Safety notices on the use of the device

Note the following safety notices when setting up and operating the device and during all
associated work such as installation, connecting up or replacing the device.

Overvoltage protection

NOTICE
Protection of the external power supply
If power is supplied to the module or station over longer power cables or networks, the
coupling in of strong electromagnetic pulses onto the power supply cables is possible. This
can be caused, for example by lightning strikes or switching of higher loads.
The connector of the external power supply is not protected from strong electromagnetic
pulses. To protect it, an external overvoltage protection module is necessary. The
requirements of EN61000-4-5, surge immunity tests on power supply lines, are met only
when a suitable protective element is used. A suitable device is, for example, the Dehn
Blitzductor BVT AVD 24, article number 918 422 or a comparable protective element.
Manufacturer:
DEHN+SOEHNE GmbH+Co.KG Hans Dehn Str.1 Postfach 1640 D-92306 Neumarkt,
Germany

3.1.1 Notices on use in hazardous areas

WARNING
EXPLOSION HAZARD
DO NOT OPEN WHEN ENERGIZED.

WARNING

The device may only be operated in an environment with pollution degree 1 or 2 (see IEC
60664-1).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 31
Installation, connecting up, commissioning
3.1 Important notes on using the device

WARNING

The equipment is designed for operation with Safety Extra-Low Voltage (SELV) by a
Limited Power Source (LPS).
This means that only SELV / LPS complying with IEC 60950-1 / EN 60950-1 / VDE 0805-1
must be connected to the power supply terminals. The power supply unit for the equipment
power supply must comply with NEC Class 2, as described by the National Electrical Code
(r) (ANSI / NFPA 70).
If the equipment is connected to a redundant power supply (two separate power supplies),
both must meet these requirements.

WARNING
EXPLOSION HAZARD
DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR
COMBUSTIBLE ATMOSPHERE IS PRESENT.

WARNING
EXPLOSION HAZARD
SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION
2 OR ZONE 2.

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I,

Zone 2, the device must be installed in a cabinet or a suitable enclosure.

3.1.2 Notices on use in hazardous areas according to IECEx / ATEX

WARNING
Requirements for the cabinet/enclosure
To comply with EU Directive 94/9 (ATEX95), the enclosure or cabinet must meet the
requirements of at least IP54 in compliance with EN 60529.

WARNING

If the cable or conduit entry point exceeds 70 °C or the branching point of conductors
exceeds 80 °C, special precautions must be taken. If the equipment is operated in an air
ambient in excess of 50 °C, only use cables with admitted maximum operating temperature
of at least 80 °C.

CP 1243-1
32 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Installation, connecting up, commissioning
3.1 Important notes on using the device

WARNING

Take measures to prevent transient voltage surges of more than 40% of the rated voltage.
This is the case if you only operate devices with SELV (safety extra-low voltage).

3.1.3 Notices regarding use in hazardous areas according to UL HazLoc

WARNING
EXPLOSION HAZARD
DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE
NON-HAZARDOUS.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-
hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations
only.

3.1.4 Notices on use in hazardous areas according to FM

WARNING
EXPLOSION HAZARD
Do not connect or disconnect while the circuit is live or unless the area is known to be free
of ignitible concentrations.

This equipment is suitable for use in Class I, Division 2, Groups A, B, C and D or non-
hazardous locations only.
This equipment is suitable for use in Class I, Zone 2, Group IIC or non-hazardous locations
only.

WARNING
EXPLOSION HAZARD
The equipment is intended to be installed within an ultimate enclosure. The inner service
temperature of the enclosure corresponds to the ambient temperature of the module. Use
installation wiring connections with admitted maximum operating temperature of at least
30 ºC higher than maximum ambient temperature.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 33
Installation, connecting up, commissioning
3.2 Installing, connecting up and commissioning

3.2 Installing, connecting up and commissioning

Prior to installation and commissioning

CAUTION
Read the system manual "S7-1200 Programmable Controller"
Prior to installation, connecting up and commissioning, read the relevant sections in the
system manual "S7-1200 Programmable Controller", refer to the documentation in the
Appendix.
When installing and connecting up, keep to the procedures described in the system manual
"S7-1200 Programmable Controller".

Pulling/plugging the module

NOTICE
Turning off the station when plugging/pulling the module
Before pulling or plugging the module, always turn off the power supply to the station.

Dimensions for installation

Figure 3-1 Dimensions for installation of the S7-1200

CP 1243-1
34 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Installation, connecting up, commissioning
3.2 Installing, connecting up and commissioning

Table 3- 1 Dimensions for installation (mm)

S7-1200 devices Width A Width B *

CPU (examples) CPU 1211C, CPU 1212C 90 mm 45 mm
CPU 1214C 110 mm 55 mm
Communications inter- CM 1241, CM 1243-5, CM 1242-5 30 mm 15 mm
faces (examples) CP 1242-7, CP 1243-1, CP 1243-7, CP 1243-8 IRC 30 mm 15 mm

* Width B: The distance between the edge of the housing and the center of the hole in the DIN rail mounting clip

You will find detailed dimensions of the module in the section Dimension drawings
(Page 139).

DIN rail clamps, control panel installation

All CPUs, SMs, CMs and CPs can be installed on the 35 mm DIN rail in the cabinet. Use the
pull-out DIN rail mounting clips to secure the device to the rail. These mounting clips also
lock into place when they are extended to allow the device to be installed in a switching
panel. The inner dimension of the hole for the DIN rail mounting clips is 4.3 mm.

Installation location

NOTICE
Installation location
The module must be installed so that its upper and lower ventilation slits are not covered,
allowing adequate ventilation. Above and below the device, there must be a clearance of 25
mm to allow air to circulate and prevent overheating.
Remember that the permitted temperature ranges depend on the position of the installed
device. You will find the permitted temperature ranges in the section Technical
specifications of the CP 1243-1 (Page 133).

Device position / permitted temperature range Installation location

Horizontal installation of the rack

Vertical installation of the rack:

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 35
Installation, connecting up, commissioning
3.3 Note on operation

Requirement: Configuration prior to commissioning

One requirement for the commissioning of the module is the completeness of the STEP 7
project data (see below, step 5).

Installing, connecting up and commissioning the module

Note
Connection with power off
Only wire up the S7-1200 with the power turned off.

Table 3- 2 Procedure for installation and connecting up

Step What to do Notes and explanations

1 Mount the CP on the DIN rail and connect it to Use a 35 mm DIN rail.
the module to its right. The slots to the left of the CPU are permitted.
2 Secure the DIN rail.
3 Connect the Ethernet cable to the CP. You will find the pinout of the interface in the section Technical
data (Page 133).
4 Turn on the power supply.
5 The remaining steps in commissioning involve The STEP 7 project data of the CP is transferred when you
downloading the STEP 7 project data. load to the station. To load the station, connect the engineer-
ing station on which the project data is located to the Ethernet
interface of the CPU.
You will find more detailed information on loading in the follow-
ing sections of the STEP 7 information system:
• "Loading project data"
• "Using online and diagnostics functions"
6 Close the front covers of the module and keep
them closed during operation.

3.3 Note on operation

NOTICE
Closing the front panels
To ensure interference-free operation, keep the front panels of the module closed during
operation.

CP 1243-1
36 Operating Instructions, 04/2017, C79000-G8976-C365-03
Configuration 4
4.1 Security recommendations
Keep to the following Security recommendations to prevent unauthorized access to the
system.

General
● You should make regular checks to make sure that the device meets these
recommendations and other internal security guidelines if applicable.
● Evaluate your plant as a whole in terms of security. Use a cell protection concept with
suitable products.
● Do not connect the device directly to the Internet. Operate the device within a protected
network area.
● Keep the firmware up to date. Check regularly for security updates of the firmware and
use them.
● Check regularly for new features on the Siemens Internet pages.
– Here you will find information on network security:
Link: (http://www.siemens.com/industrialsecurity)
– Here you will find information on Industrial Ethernet security:
Link: (http://w3.siemens.com/mcms/industrial-communication/en/ie/industrial-ethernet-
security/Seiten/industrial-security.aspx)
– You will find an introduction to the topic of industrial security in the following
publication:
Link:
(http://w3app.siemens.com/mcms/infocenter/dokumentencenter/sc/ic/InfocenterLangu
agePacks/Netzwerksicherheit/6ZB5530-1AP02-
0BA4_BR_Network_Security_en_112015.pdf)

Physical access
Restrict physical access to the device to qualified personnel.

Network attachment
Do not connect the PC directly to the Internet. If a connection from the CP to the Internet is
required, arrange for suitable protection before the CP, for example a SCALANCE S with
firewall or use the CP 1543SP-1.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 37
Configuration
4.1 Security recommendations

Security functions of the product

Use the options for security settings in the configuration of the product. These includes
among others:
● Protection levels
Configure a protection level of the CPU.
You will find information on this in the information system of STEP 7.
● Security function of the communication
– Enable the security functions of the CP and set up the firewall.
If you connect to public networks, you should use the firewall. Think about the services
you want to allow access to the station via public networks. By using the "bandwidth
limitation" of the firewall, you can restrict the possibility of flooding and DoS attacks.
– Use the secure protocol variants NTP (secure) and SNMPv3.
– Using the security functions of the telecontrol protocols.
– Leave access to the Web server of the CPU (CPU configuration) and to the Web
server of the CP disabled.
● Logging function
Enable the function in the security configuration and check the logged events regularly for
unauthorized access.

Passwords
● Define rules for the use of devices and assignment of passwords.
● Regularly update the passwords to increase security.
● Only use passwords with a high password strength. Avoid weak passwords for example
"password1", "123456789" or similar.
● Make sure that all passwords are protected and inaccessible to unauthorized personnel.
See also the preceding section for information on this.
● Do not use one password for different users and systems.

Protocols

Secure and non-secure protocols

● Only activate protocols that you require to use the system.
● Use secure protocols when access to the device is not prevented by physical protection
measures.
– The NTP protocol provides a secure alternative with NTP (secure) if you do not use
telecontrol communication.
– The HTTP protocol provides a secure alternative with HTTPS when accessing the
Web server (configuration of the CPU).

CP 1243-1
38 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.1 Security recommendations

Table: Meaning of the column titles and entries

The following table provides you with an overview of the open ports on this device.
● Protocol / function
Protocols that the device supports.
● Port number (protocol)
Port number assigned to the protocol.
● Default of the port
– Open
The port is open at the start of the configuration.
– Closed
The port is closed at the start of the configuration.
● Port status
– Open
The port is always open and cannot be closed.
– Open after configuration
The port is open if it has been configured.
– Open (login, when configured)
As default the port is open. After configuring the port, the communications partner
needs to log in.
– Closed after configuration
The port is closed because the CP is always client for this service.
● Authentication
Specifies whether or not the protocol authenticates the communications partner during
access.

Protocol / function Port number (pro- Default of the port Port status Authentication
tocol)
DNP3 listener 20000 (TCP) Closed Open after configuration No
port
IEC listener port 102 (TCP) Closed Open after configuration No
S7 and online 2404 (TCP) Open Open after configuration * No
connections
Online security 8448 (TCP) Closed Open after configuration No
diagnostics
HTTP 80 (TCP) Closed Open after configuration No
HTTPS 443 (TCP) Closed Open after configuration Yes
SNMP 161 (UDP) Open Open after configuration Yes (with SNMPv3)

* For information on avoiding opening the port during diagnostics, see section Online
security diagnostics via port 8448 (Page 123).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 39
Configuration
4.2 Configuration in STEP 7

4.2 Configuration in STEP 7

Configuration in STEP 7
You configure the modules and networks in SIMATIC STEP 7. You will find the required
version in the section Software requirements (Page 23).

Fitting CPs in a rack

You can configure a maximum of three CMs/CPs per station.

Requirement for configuring the communication

One requirement for configuring communication between the CP and the communications
partner is the programming of the assigned CPU and the input and output data of the station.
PLC tags must also be created to assign the user data to the data points.
For more detailed information, refer to the following sections.

How to configure telecontrol communication in STEP 7

Follow the steps below when configuring:
1. Create a STEP 7 project.
2. Insert the required SIMATIC stations.
Configuration of control center devices and applications and connections between the CP
and partner is neither possible nor necessary.
3. Insert the CPs and the required input and output modules in the stations.
4. Create an Ethernet network.
5. Connect the stations to the Ethernet subnet.
6. Configure the inserted CPs.
For details on configuring the communication, refer to the following section.
7. Save the project.
You will find more detailed information on configuring the CP in the Information system of
STEP 7 and in the following sections.

Loading and storing the configuration data

When you load the station, the project data of the station including the configuration data of
the CP is stored on the CPU.
You will find information on loading the station in the STEP 7 information system.

CP 1243-1
40 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.3 Addressing and authentication

4.3 Addressing and authentication

4.3.1 TeleControl Basic

IP address of the CP
Since the CP always establishes the connection with TCSB, a dynamic IP address can be
assigned to the CP by the Internet service provider.
To change the IP address during operation, refer also to the section Changing the IP
address during runtime (Page 119).

Address and authentication data for communication with TCSB

The following information is required for the STEP 7 configuration of the CP for
communication with TCSB:
● Parameters in the "Partner stations" parameter group
– Partner IP address
IP address or host name of the DSL router via which the telecontrol server is
connected to the Internet.
A fixed IP address is recommended.
– Partner port (port number of the listener port of TCSB)
● Parameters in the "Security > CP identification" parameter group
– Project number
– Station number
– Password (for authentication)

4.3.2 DNP3 / IEC

To configure and commission the CP, the following information is required:

Address information of the master

The following information is required for the STEP 7 configuration of the CP:
● Address of the master
– IP address
or
– Name that can be resolved with DNS
If you use DNS, there must be a DNS server (see below) and this must be reachable
for the CP.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 41
Configuration
4.4 Time-of-day synchronization

● Port number of the listener port of the master

● DNS server address(es)
You require the DNS server address if you address the master using a name that can be
resolved by DNS.

Configurations with connections over the Internet: VPN connections

For connections running via the Internet, dynamic IP addresses can be used.
To allow communication in both directions and to ensure that the data is protected during
transfer, a connection with a VPN tunnel is necessary. For this the security modules of the
SCALANCE S or SCALANCE M series are available.
Remember the following points when configuring:
● You configure the master IP address as normal.
● When configuring the CP interface, configure the IP address of the router.
● You create the VPN configuration with SCALANCE S/M both for the station end and for
the control center end in STEP 7.

4.4 Time-of-day synchronization

Synchronization method of the CP

Note
Time-of-day synchronization of the CP
With applications that require time-of-day synchronization (e.g. telecontrol), you need to
synchronize the time of day of the CP regularly. If you do not synchronize the time of day of
the CP regularly, there may be deviations of several seconds per day in the time information
of the CP.
With security functions enabled, you need to enable time-of-day synchronization.

Note
Recommendation for setting the time
Synchronization with a external clock at intervals of approximately 10 seconds is
recommended. This achieves as small a deviation as possible between the internal time and
the absolute time.

CP 1243-1
42 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.4 Time-of-day synchronization

The CP supports the following methods of time-of-day synchronization:

● Time from partner
The CP adopts the time-of-day from the communications partner in the master station.
Only when telecontrol communication is enabled.
● NTP
The time of day is synchronized by an NTP server in the connected network.
The method can also be used when the telecontrol communication is enabled.
With CPs as of firmware version V3, the address of the NTP server can also be entered
as a URL, e.g. <ntp.server.com>. For this a DNS server is required.
● NTP (secure)
The secure method NTP (secure) uses symmetrical keys according to the hash
algorithms MD5 or SHA-1.
On the CP you specify the servers used.
You configure NTP servers of the type NTP (secure) in the global security settings of
STEP 7.
● Time from the CPU
As of V4.2, the CPU synchronizes all CMs/CPs of the station with a synchronization cycle
of 10 seconds.
Parameters of the CPU:
If for the CPU the option "CPU synchronizes the modules of the device" is enabled, all
smart modules of the station (CPs with of firmware ≥ V2.1.77) are synchronized with the
CPU time in a synchronization cycle of 10 seconds.

Parameter groups for time-of-day synchronization

You can configure time-of-day synchronization in the following parameter groups:
● Ethernet interface
Here you create the configuration under the following conditions:
– Telecontrol communication is disabled.
– The security functions are disabled.
● Security
Here you create the configuration under the following condition:
– The security functions are enabled.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 43
Configuration
4.4 Time-of-day synchronization

Dependence of the synchronization method on the use of the CP

Depending on the use of the telecontrol communication or the security functions, the
following synchronization methods can be selected:
● Telecontrol communication disabled, security disabled
– NTP
– Time from the CPU
● Telecontrol communication disabled, security enabled
– NTP
– NTP (secure)
– Time from the CPU
● Telecontrol communication and security enabled
– Time from partner
– NTP
– NTP (secure)
– Time from the CPU

Time-of-day synchronization with the S7-1200

When using an external time source, the S7-1200 station can obtain the current time of day
both via the CPU as well as via a CP.
With the S7-1200 there is no forwarding of the time of day from the station to the subnet.

Note
Recommendation: Time-of-day synchronization only by 1 module
Only have the time of day of the station from an external time source synchronized by a
single module so that a consistent time of day is maintained within the station.
When the CPU takes the time from the CP, disable time-of-day synchronization of the CPU.

Time-of-day synchronization of the CPU

The following synchronization methods are possible for the CPU:
● NTP
Only this option can be configured actively for the CPU:
● Time from CP
The CPU adopts the time of day from a CP of the station if time forwarding from the CP to
the CPU is enabled (see below).

CP 1243-1
44 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.5 Communication types

Forwarding the time from the CP to the CPU

Note
Forwarding the time to the CPU
Depending on the firmware version of the modules involved, the time-of-day of the CP is
forwarded to the CPU in different ways:
• Optional forwarding of the CP time to the CPU using a PLC tag
• Obligatory forwarding of the CP time to the CPU via the backplane bus

The forwarding of the CP time to the CPU depends on the firmware version of the CP and
the CPU. Note the following behaviour.
● CP firmware ≤ V2.1.6x
With this firmware version the CP can make the time-of-day available to the CPU as an
option via a PLC tag. When this PLC tag is read cyclically by the CPU, the CPU adopts
the CP time.
In the parameter group "Communication with the CPU", you can set whether or not the
current time of day of the CP will be made available to the CPU via a PLC tag. For TLC
tags, see parameter group "Communication with the CPU" of the CP.
● CP firmware ≥ V2.1.77 and CPU firmware ≥ V4.2
If both modules in the station have the named firmware versions, the time of day of the
CP is automatically forwarded to the CPU.
Since the CPU automatically adopts the CP time, you no longer require the forwarding
option using the PLC tag.
If for the CPU the option "CPU synchronizes the modules of the device" is enabled in
"PROFINET interface > Time synchronization", all smart modules of the station are
synchronized with the CPU time.

4.5 Communication types

In this parameter group, you enable the communication types of the CP.
To minimize the risk of unauthorized access to the station via Ethernet, you need to enable
the communications services that the CP will execute individually. You can enable all options
but at least one option should be enabled.

"Communication types" parameter group

● Enable telecontrol communication
– TeleControl Basic
– DNP3
– IEC 60870-5
Note that if you change the telecontrol communication type later, all specific parameters
are deleted. These also include data point and partner information among other things.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 45
Configuration
4.6 Ethernet interface

● Activate online functions

Enables access to the CPU for the online functions via the CP (diagnostics, loading
project data etc.). If the function is enabled, the engineering station can access the CPU
via the CP.
If the option is disabled, you have no access to the CPU via the CP with the online
functions. Online diagnostics of the CPU with a direct connection to the interface of the
CPU however remains possible.
● Enabling S7 communication
Enables the functions of S7 communication with a SIMATIC S7 on the CP.
If you configure S7 connections to the relevant station, and these run via the CP, you will
need to enable this option.

4.6 Ethernet interface

4.6.1 CP identification
The parameter group is available only when telecontrol communication is enabled.

CP addressing
The parameter group is used for addressing and identification of the CP in the network.
● TeleControl Basic
You will find the parameters for the TeleControl Basic protocol in "Security", refer to the
section CP iIdentifcation with the TeleControl Basic protocol (Page 64).
● DNP3
The station address is the DNP address.
Entry of the station address (digits only). Permitted range of values: 1...65519.
● IEC
The station address is the “common address of the ASDU" or the address of the
information object.
Entry of the station address (digits only). Permitted range of values: 1...65534.

4.6.2 Time-of-day synchronization

Time-of-day synchronization
For the configuration of the time-of-day synchronization read the section Time-of-day
synchronization (Page 42).

CP 1243-1
46 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.6 Ethernet interface

4.6.3 Advanced options

TCP connection monitoring

The settings made here apply globally to all configured TCP connections of the CP.
With TeleControl Basic and DNP3:
Note the option of overwriting the values configured here for individual communications
partners, refer to the section Partner stations (Page 54).
● TCP connection monitoring time
Function: If there is no data traffic within the TCP connection monitoring time, the CP
sends a keepalive to the communications partner.
Default setting: 180 s. Permitted range: 1...65535 s.
– The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface globally for all TCP
connections. The parameter is preset to 180 seconds as default.
– The parameter below "Partner stations"
The parameter "TCP connection monitoring time" occurs again with the individual
partners in the parameter group "Connection to partner". This parameter applies only
to the individual partner. The value of 180 seconds preset on the Ethernet interface is
adopted for the individual partners.
If for any reason you want to change the value of the TCP connection monitoring time
for individual partners, you can adapt the value for every partner individually in
"Partner stations". If. for example, you want to check the connection at shorter
intervals, reduce the value.
● TCP keepalive monitoring time
After sending a keepalive, the CP expects a reply from the communications partner within
the keepalive monitoring time. If the CP does not receive a reply within the configured
time, it terminates the connection.
Default setting: 10 s. Permitted range: 1...65535 s.
– The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface as a global setting for all
TCP connections.
– The parameter below "Partner stations"
As with the TCP connection monitoring time, the value of "Partner stations" can be
adapted for each partner individually.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 47
Configuration
4.6 Ethernet interface

4.6.4 Transmission settings – TeleControl Basic

Transmission settings – TeleControl Basic

● Connection establishment delay
The settings made here apply to the connection to the telecontrol server.
The reconnection delay is the waiting time between repeated attempts to establish the
connection by the CP when the telecontrol server is not reachable or the connection has
aborted.
This waiting time avoids continuous connection establishment attempts at short intervals
if there are connection problems.
A basic value is configured for the waiting time before the next connection establishment
attempt. Starting at the basic value, the current waiting time is doubled after every 3
unsuccessful retries up to a maximum value of 900 s.
Default setting: 10 s. Permitted range of values for the basic value: 10...300 s
Example:
A configured basic value 20 results in the following intervals (waiting times) between the
attempts to re-establish a connection:
– three times 20 s
– three times 40 s
– three times 80 s
– etc. up to max. 900 s

Note
If the partner cannot be reached, connection establishment via the mobile wireless
network can take several minutes. This may depend on the particular network and current
network load.
Depending on your contract, costs may result from each connection establishment
attempt.

● Send monitoring time

Time for the arrival of the acknowledgment from the partner (Telecontrol server) after
sending unsolicited frames. The time is started after sending an unsolicited frame. If no
acknowledgement has been received from the partner when the send monitoring time
elapses, the frame is repeated up to three times. After three unsuccessful attempts, the
connection is terminated and re-established.
Default setting: 60 s. Permitted range: 1...65535 s.
● Watchdog monitoring time
With the watchdog cycle, the CP checks the connection to the telecontrol server. The
watchdog cycle is the interval without data exchange between the CP and telecontrol
server after which the CP sends a watchdog frame to the telecontrol server. The
watchdog cycle is only configured with TCSB (parameter "Keepalive monitoring time").

CP 1243-1
48 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.6 Ethernet interface

The value configured in TCSB is transferred by the telecontrol server to the CP the first
time the connection is established.
Each time the CP transfers data to TCSB and receives the acknowledgment from the
telecontrol server, the CP starts the watchdog cycle. When the watchdog cycle has
expired the CP sends a watchdog frame to the telecontrol server.
After sending a watchdog frame, the CP starts the watchdog monitoring time within which
the CP expects a reply from the telecontrol server. If the CP does not receive a reply from
the Telecontrol server within the monitoring time, it terminates and re-establishes the
connection.
Default setting: 30 s. Permitted range: 0...65535 s. If you enter 0 (zero), the function is
disabled.
● Key exchange interval
Here, you enter the interval in hours after which the key is exchanged again between the
CP and the telecontrol server. The key is a security function of the telecontrol protocol
used by the CP and TCSB V3.
Default setting: 8 s. Permitted range: 0...65535 s. If you enter 0 (zero), the function is
disabled.

4.6.5 Transmission settings – DNP3

Transmission settings – DNP3

● Disturbance bit
The disturbance bit can be used as bit 1.6 (IIN1.6) of the "Internal Indication Bytes" to
indicate to the master when the CPU is in STOP mode.
● Max. time between Select and Operate
Max. duration (seconds) between Select and Operate. For a Select command to be
transferred to the CPU and to take effect, no other frame may be sent to the station
between Select and Operate.
Permitted range: 1..65535
Default setting: 1
● Frame repetitions
Number of frame repetitions at the Data Link Layer if no acknowledgement is received
from the master.
Permitted range: 0 ... 255
Default setting: 0
If you enter 0 (zero), the function is disabled.
● Connection confirmation
Condition for the CP to request a connection confirmation from the master (never,
always, only with segmented frames).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 49
Configuration
4.6 Ethernet interface

● Connection monitoring time

Time (in seconds) within which an acknowledgement is expected from the master.
Permitted range: 0...65535
Default setting: 2
If you enter 0 (zero), the function is disabled.
● Transfer mode "Unsolicited"
Transfer mode for events
– Spontaneous
Event frames are transferred immediately.
– Conditional spontaneous
Event messages are only sent when spontaneous frames are sent or the partner
establishes the connection.
● Max. number of unsolicited frames
Maximum number of repetitions of unsolicited frames if no acknowledgement is received
from the communications partner .
Permitted range: 0...255
Default setting: 3
● Monitoring time for unsolicited frames
Time (in seconds) within which an acknowledgement of unsolicited frames is expected
from the master.
Permitted range: 1...65535
Default setting: 5
● Buffer for class 1 / 2 / 3 events
Here, for each of the three event classes you specify the number of events after which
the stored events are sent to the communications partner.
Permitted range: 1 ... 255.
● Delay time class 1 / 2 / 3 events
Here, for each of the three event classes you specify the maximum time in seconds the
events can be stored in the send buffer before they are sent to the communications
partner.
Permitted range: 0 ... 65535
If you enter 0 (zero), the function is disabled.
● Event class for image memory
Selection of an event class in which only the last current values are stored in the send
buffer.
In the default setting all values of events of classes 1 and 2 are stored in the send buffer,
of class 3 only the current values (image memory procedure).

CP 1243-1
50 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.6 Ethernet interface

You will find details of how the image buffer and send buffer work as well as the options for
transferring data in the section Process image, type of transmission, event classes, triggers
(Page 97).

4.6.6 Transmission settings - IEC

Transmission settings - IEC 60870-5

● Max. time between Select and Operate
Max. duration (seconds) between Select and Operate. For a Select command to be
transferred to the CPU and to take effect, no other frame may be sent to the station
between Select and Operate.
Permitted range: 1..65535
Default setting: 1
● Monitoring time for connection establishment (t0)
Monitoring time for the connection establishment (t0) in seconds. If the communications
partner does not confirm connection establishment within the monitoring time, the CP
attempts to establish the connection again.
Permitted range: 1..255
Default setting: 30
● Frame monitoring time (t1)
Monitoring time in seconds for the acknowledgement of frames sent by the CP by the
communications partner. The monitoring time applies to all frames sent by the CP in I, S
and U format.
If the partner does not send an acknowledgment during the monitoring time, the CP
terminates the connection to the partner.
Permitted range: 1..255
Default setting: 15

Note
Settings on the master
When configuring the monitoring times t1 and t2 make sure that you make the
corresponding settings on the master so that there are no unwanted error messages or
connection aborts.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 51
Configuration
4.6 Ethernet interface

● Monitoring time for S and U frames (t2)

Monitoring time in seconds for the acknowledgment of data frames of the master by the
CP.
After receiving data from the master, the CP acknowledges the received data as follows:
– If the CP sends data to the master itself within t2, it acknowledges the data frames
received from the master during t2 at the same time along with the sent data frame (I
format).
– The CP sends an acknowledgment frame (S format) to the master of the latest when t2
elapses.
Permitted range: 1 ... 255
Default setting: 10
The value of t2 should be less than that of t1.
● Idle time for test frames (t3)
Monitoring time in seconds during which the CP has not received any frames from the
master.
When t3 elapses, the CP sends a test/control frame (U format) to the master.
This parameter is intended for situations in which longer idle periods occur; in other
words, times when there is no data traffic.
Permitted range: 1 ... 255
Default setting: 30
● Difference between send sequence number N(S) and receive sequence number N(R) (k)
The difference between the send sequence number and receive sequence number of a
frame.
The master returns the send sequence number of a frame from the CP that the sending
CP then saves as the receive sequence number. Frames whose send sequence number
is lower than the receive sequence number after the difference configured here is added
are evaluated as having been successfully transferred and are deleted from the send
buffer of the CP.
Permitted range: 1 ... 64
Default setting: 12
● Max. number of unacknowledged data frames (w)
w: Maximum number of received data frames (I-APDUs), after which the oldest frame
received from the master must be acknowledged.
Permitted range: 1..8
Default setting: 8
The value must be less than the value of "Difference between send and receive
sequence number" (k).

CP 1243-1
52 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.7 SNMP

Acknowledgment mechanism for the IEC protocol

With each sent data frame, the CP sends a continuous send sequence number. The data
frame remains initially stored in the send buffer.
When it receives the data frame, the master sends the send sequence number from this or
(if several frames are received) the last frame as an acknowledgement to the CP. The CP
saves the send sequence number returned by the master as a receive sequence number
and uses it as an acknowledgement.
Frames whose send sequence number is equal to or lower than the current receive
sequence number are evaluated as having been successfully transferred and are deleted
from the send buffer of the CP.
Recommendations of the specification:
● w should not be higher than 2/3 of k.
● Recommended value for k: 12
● Recommended value for w: 8

4.7 SNMP

SNMP
The CP supports the following SNMP versions:
● SNMPv1
Available with security functions disabled.
Note that with this read and write access to the module is possible. In this case, other
settings are not possible.
The configuration of the community strings is only possible if the security functions are
enabled.
The CP uses the following community strings to authenticate access to its SNMP agent
via SNMPv1:

Access to the SNMP agent in the CP Community string for authentication in SNMPv1
*)

Read access public

Read and write access private

*) Note the use of lowercase letters!

● SNMPv3
Available only when security functions are enabled
For information on the configuring SNMPv3, refer to the section SNMP (Page 70).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 53
Configuration
4.8 Partner stations

Configuration
● "Enable SNMP"
If the option is enabled, communication via SNMPv1 is enabled on the CP.
If the option is disabled, queries from SNMP clients are not replied to by the CP either via
SNMPv1 or via SNMPv3.

4.8 Partner stations

The parameter group is only displayed when telecontrol communication is enabled.

4.8.1 Partner stations > General parameters

Listener port

Only with DNP3 / IEC

Here the listener port of the module, port for connection requests of the communications
partner are displayed.
● Default for the DNP3 protocol: 20000
● Default for the IEC protocol: 2404
You can change the port number for the module. Keep in mind the settings on the
communications partner (master).
Permitted range: 1024...65535

Partner'X' / telecontrol server

● Activate partner
– TeleControl Basic
The telecontrol server is enabled as the only possible partner in the default settings.
– DNP3 / IEC
By enabling the option the master that can then be configured is enabled for
communication.
● Partner number
The partner number is assigned by the system. It is required during data point
configuration to assign data points to their communications partners.

CP 1243-1
54 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.8 Partner stations

● Station address / Master station address

– TeleControl Basic
The station address of the telecontrol server is assigned automatically by the system if
telecontrol communication is enabled.
– DNP3
For identification the station address mut be configured on the master.
– IEC
Common ASDU address

Connection to partner
● Partner IP address
IP address or host name (FQDN) of the partner. This can, for example, also be the FQDN
of a DynDNS service.
– Note on TeleControl Basic
If the CP is connected to a TCSB redundancy group (TCSB V3), here configure the
public IP address of the DSL router via which the telecontrol server can be reached
from the Internet. Set the port forwarding on the DSL router so that the public IP
address (external network) is led to the virtual IP address of the TCSB server PCs
(internal network). The station does not therefore receive any information telling it
which of the two computers of the redundancy group it is connected to.
See also section Addressing in the redundant TCSB system (Page 57).
● Connection monitoring
Only for TeleControl Basic and DNP3
When the function is enabled, the connection to the communications partner is monitored
by sending keepalive frames.
The TCP connection monitoring time is set for all TCP connections of the CP in the
parameter group of the Ethernet interface. The setting applies to all TCP connections of
the CP.
Here in the parameter group "Partner stations", the globally set TCP connection
monitoring time can be set separately for the partner. The value set here for the partner
overwrites the global value that was set in the "Ethernet interface (X1) > Advanced
options > TCP connection monitoring" parameter group.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 55
Configuration
4.8 Partner stations

● TCP connection monitoring time

Only for TeleControl Basic and DNP3
Function: If there is no data traffic within the TCP connection monitoring time, the CP
sends a keepalive to the communications partner.
Default setting: 180 s. Permitted range: 1...65535 s.
The monitoring time is specified at a higher level for the Ethernet interface as the default
for all configured TCP connections.
– The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface globally for all TCP
connections. The parameter is preset to 180 seconds as default.
– The parameter below "Partner stations"
The parameter "TCP connection monitoring time" occurs again with the individual
partners in the parameter group "Connection to partner". This parameter applies only
to the individual partner. The value of 180 seconds preset on the Ethernet interface is
adopted for the individual partners.
If for any reason you want to change the value of the TCP connection monitoring time
for individual partners, you can adapt the value for every partner individually in
"Partner stations". If. for example, you want to check the connection at shorter
intervals, reduce the value.
● TCP keepalive monitoring time
Only for TeleControl Basic and DNP3
If the value configured here differs from the value configured in the Ethernet interface
parameter group, the monitoring time of the "Partner stations" parameter group is used.
After sending a keepalive, the CP expects a reply from the communications partner within
the keepalive monitoring time. If the CP does not receive a reply within the configured
time, it terminates the connection.
Default setting: 10 s. Permitted range: 1...65535 s.
– The parameter below the Ethernet interface
The monitoring time is configured for the Ethernet interface as a global setting for all
TCP connections.
– The parameter below "Partner stations"
As with the TCP connection monitoring time, the value of "Partner stations" can be
adapted for each partner individually.
● Connection mode
In the "Permanent" connection mode, there is a permanent connection to the
communications partner.
The CP only supports this connection mode.
● Connection establishment
Specifies the communications partner that establishes the connection (always the CP).

CP 1243-1
56 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.8 Partner stations

● Protocol type
Only for DNP3
Selection of the protocol type on the transport layer: TCP / UDP
● Partner port
Only with TeleControl Basic
Number of the listener port of the telecontrol server.

4.8.2 TeleControl Basic

4.8.2.1 Addressing in the redundant TCSB system

Addressing of the redundant telecontrol server

● Addressing of the TCSB redundancy group by the stations using one IP address
In the LAN in the master station to which the TCSB server PCs and the DSL router (e.g.
SCALANCE M) are connected, the Network Load Balancing (NLB) of the computer
operating system will assign a common virtual IP address to the two server PCs.
This IP address is configured depending on the network setup:
– If only one CP without a DSL router is connected, the virtual address assigned by the
NLB must be configured in the CP as the IP address of the telecontrol server.
– If a DSL router is used, only one IP address will be configured to address the
redundant telecontrol server in the stations, the public address of the DSL router.
Set the port forwarding on the DSL router so that the public IP address (external
network) is led to the virtual IP address of the TCSB server PCs (internal network).
Only the public IP address is reachable from the Internet. The station does not
therefore receive any information telling it which of the two computers of the
redundancy group it is connected to.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 57
Configuration
4.8 Partner stations

4.8.2.2 Advanced settings

Telecontrol server > Advanced settings

● Report partner status
If the "Report partner status" function is enabled, the CP signals the status of the
communication to the remote partner.
– Bit 0 of "PLC tag for partner status" (data type WORD) is set to 1 if the partner can be
reached.
– Bit 1 is set to 1 if all the paths to the remote partner are OK (useful with redundant
paths).
– Bits 2-3 indicate the status of the send buffer (frame memory).
The following values are possible:
- 0: Send buffer OK
- 1: Send buffer threatening to overflow (more than 80 % full).
- 3: Send buffer has overflowed (fill level 100 % reached).
As soon as the fill level drops below 50%, bits 2 and 3 are reset to 0.
Bits 4 to 15 of the PLC tags are not used and do not need to be evaluated in the program.

4.8.2.3 Partner for inter-station communication

Inter-station communication
In this table, you specify the S7 stations with which the current station will use inter-station
communication. Connections for inter-station communication run via the telecontrol server.

Partner
The partner number is assigned by the system. It is required during data point configuration
to assign data points to their communications partners.
For inter-station communication, the partner is addressed with the parameters "Project",
"Station" and "Slot".

Project
Here, enter the project number of the CP in the partner station. (Parameter group "Security >
CP identification" on the partner)

Station
Here, enter the station number of the CP in the partner station. (Parameter group "Security >
CP identification" on the partner)

CP 1243-1
58 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.8 Partner stations

Slot
Here, enter the slot number of the CP in the partner station via which the connection will be
established.

Frame memory
Activate the option for enabling inter-station communication.
The frames are stored in the send buffer (frame memory) of the CP if the connection is
disturbed. Note that the capacity of the frame memory is shared by all communications
partners.

Access ID
The access ID displayed here is formed from the hexadecimal values of project number,
station number and slot. The parameter of the type DWORD is allocated as follows:
● Bits 0 - 7: Slot
● Bits 8 - 20: Station number
● Bits 21 - 31: Project number

4.8.3 DNP3 / IEC

4.8.3.1 Advanced settings (DNP3 / IEC)

Advanced settings
● Partner monitoring time
If the CP does not receive a sign of life from the communications partner within the
configured time, the CP interprets this as a fault/error on the partner. The CP aborts the
connection and attempts to re-establish it.
If you enter 0, the function is deactivated.
● DNP3 level
Only for DNP3
Indicates the DNP3 implementation level supported by the CP
In the DNP3 specification, various levels of protocol conformity are and they describe the
supported range of functions (subset) of a master or a station. These levels
(implementation levels) are known as "DNP3 Application Layer protocol Level" and
abbreviated with DNP3-L1 to DNP3-L4.
For the communication between the CP and the master, the DNP3 level supported by the
master must be known.
The selection of the level used by the DNP3 CP which must correspond to that of the
connected master is set separately in STEP 7 for each individual communications partner
(DNP3 master).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 59
Configuration
4.8 Partner stations

The CP supports the following implementation levels:

– Level 1
– Level 2
– Level 3
– Level 4
– Level 4+
The implementation level known here as Level 4+ that is not specified in the standard
contains the range of functions of Level 4 and in addition support of the following DNP3
data types / variations:
– 64-bit analog value as floating-point number without time of day
– 64-bit analog value as floating-point number with time of day
– Counter event with time of day in 16-bit format
– Counter event with time of day in 32-bit format
● Event transmission mode
Only for DNP3
Mode with which DNP events are transferred to this communications partner:
– Chronological transfer of individual frames
or
– Transfer of collected frames per data point as a block.
● Report partner status
If the "Report partner status" function is enabled, the CP signals the status of the
communication to the remote partner.
– Bit 0 of "PLC tag for partner status" (data type WORD) is set to 1 if the partner can be
reached.
– Bit 1 is set to 1 if all the paths to the remote partner are OK (useful with redundant
paths).
– Bit 2 indicates the status of the send buffer (frame memory).
The following values are possible:
- 0: Send buffer OK
- 1: Send buffer threatening to overflow (more than 80 % full).
- 3: Send buffer has overflowed (fill level 100 % reached).
As soon as the fill level drops below 50%, bit 3 is reset to 0.
Bits 3 to 15 of the PLC tags are not used and do not need to be evaluated in the program.

Communication with the CPU

Using the first three parameters you specify the CPU access by the CP in the CPU scan
cycle. You will find the structure of the CPU scan cycle in the section Read cycle (Page 96).

CP 1243-1
60 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.8 Partner stations

The fourth parameter "Frame memory size" decides the size of the send buffer on the CP for
frames of data points that are configured as an event.
● Cycle pause time
Wait time between two scan cycles of the CPU memory area
● Max. number of write jobs
Maximum number of write jobs to the CPU memory area within a CPU scan cycle
● Max. number of read jobs
Maximum number of low-priority read jobs from the CPU memory area within a CPU scan
cycle.
● Frame memory size
Here, you set the size of the frame memory for events (send buffer).
The size of the frame memory is divided equally among all configured communications
partners. You will find the size of the frame memory in the section Configuration limits
and performance data (Page 15).
You will find details of how the send buffer works (storing and sending events) as well as
the options for transferring data in the section Process image, type of transmission, event
classes, triggers (Page 97).

Watchdog bit
● CP monitoring
Via the watchdog bit the CPU can be informed of the status of the telecontrol
communication of the CP.

CP time of day
● CP time to CPU
Using this function, the CP can make its time of day available to the CPU.
You will find details in the STEP 7 information system.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 61
Configuration
4.8 Partner stations

CP diagnostics
With the parameter group, you have the option of reading out advanced diagnostics data
from the CP using PLC tags.
● Enable advanced CP diagnostics
Enable the option to be able to use advanced CP diagnostics.
If the option is enabled, at least the "Diagnostics trigger tag" must be configured.
The following PLC tags for the individual items of diagnostics data can be enabled
selectively.
● Diagnostics trigger tag
If the PLC tag (BOOL) from the user program of the CPU is set to 1, the CP updates the
values of the PLC tags that can then be configured for the advanced diagnostics.
After writing the current values to the following PLC tags, the CP sets the "Diagnostics
trigger tag" to 0 signaling the CPU that the updated values can be read from the PLC
tags.

Note
Fast setting of the diagnostics trigger variable
Triggers must not be set faster than a minimum interval of 500 milliseconds.

● Frame memory overflow

PLC tag (data type byte) for the send buffer overflow pre-warning. Bit 0 is set to 1 when
80% of the fill level of the send buffer is reached.
● Frame memory size
PLC tag (data type DWord) for the occupation of the send buffer. The number of saved
frames is displayed.
● Date of last successful logon to TCSB
Only for the TeleControl Basic protocol
PLC tag (data type DTL) for the date on which the CP last logged in to the telecontrol
server.
● Date of last unsuccessful logon to TCSB
Only for the TeleControl Basic protocol
PLC tag (data type DTL) for the date on which the CP was last unable to log in to the
telecontrol server.
● TeleService status
The PLC tag (BOOL) indicates whether a TeleService session is active.
– 0 = No TeleService session active
– 1 = TeleService session active

CP 1243-1
62 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

● VPN status
The PLC tag (BOOL) indicates whether a VPN tunnel is established:
– 0 = No VPN tunnel established
– 1 = VPN tunnel established

4.9 Security
You will find an overview of the range and use of the security functions in section Security
functions (Page 13).
For the configuration limits of the security functions refer to the section Configuration limits
and performance data (Page 15).

4.9.1 Parameter overview

Parameter groups
If the security functions of the CP are enabled, you will find the following parameter groups
for configuring the CP:
● CP identification
Only with the TeleControl Basic protocol
Here, you configure parameters for authenticating the CP with the telecontrol server. You
will find detailed information about the parameters below.
● DNP3 security options
Only with the DNP3 protocol
Here, you configure protocol-specific security functions. You will find detailed information
about the parameters below.
● Firewall
See section Firewall (Page 67).
● Time synchronization
For the configuration of the time-of-day synchronization read the section Time-of-day
synchronization (Page 42).
● E-mail configuration
See section E-mail configuration (Page 69).
● Log settings
Here you make the settings for logging events relevant for security.
See section Log settings - Filtering of the system events (Page 70).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 63
Configuration
4.9 Security

● SNMP
Here you make the settings for the SNMP agent on the CP.
See section SNMP (Page 70).
● Certificate manager
See section Certificate manager (Page 72).
In the global security settings of STEP 7 among other things you will find the following
parameter groups:
● VPN groups
Here you configure the VPN communication, refer to the section VPN (Page 74).
● User management
Here you configure the users, roles and rights for the TeleService access, refer to the
section Configuration of the TeleService access (Page 80).

4.9.2 CP iIdentifcation with the TeleControl Basic protocol

In the "CP identification" parameter group, you configure the following information for
authenticating the CP with the telecontrol server:
● Project number
The project number is the same for all telecontrol CPs in a STEP 7 project. TCSB
evaluates project numbers from 1 ... 2000.
If you change the project number, this parameter is changed for all CPs in the STEP 7
project.
● Station number
For each S7-1200 station with a telecontrol CP, an individual station number is
configured. TCSB evaluates station numbers from 1 ... 8000.
● Telecontrol password
Password for the authentication of the CP on the telecontrol server
8 ... 29 characters of the ASCII character set 0x20...0x7e
The password can be the same for all CPs of the STEP 7 project. The same password is
configured in TCSB for this station.
● Access ID
The displayed Access ID is formed from the hexadecimal values of project number,
station number and slot. The parameter of the type DWORD is allocated as follows:
– Bits 0 - 7: Slot
– Bits 8 to 20: Station number
– Bits 21 to 31: Project number

CP 1243-1
64 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

4.9.3 DNP3 security options

Partner'X'

Preliminary remarks: Authentication and key exchange

If the security function is enabled, the DNP3 master and CP authenticate themselves with a
secret key, the pre-shared key.
With the help of the common pre-shared key, after the first connection establishment
between master and CP session keys are agreed that are then renewed cyclically. Renewal
of the session keys is normally initiated by the master. The criteria for renewing the key are
specified in the following parameters.
● Key exchange interval
● Authentication requests before key exchange
As soon as one of these conditions is met, the session key is renewed.

Parameters
● Enable DNP3 security options
Enable the option if you want to use the security mechanisms.
● IKE mode
Selection of the mode for key exchange. Range of values:
– Aggressive Mode
The Aggressive Mode is somewhat faster but transfers the identity unencrypted.
– Main Mode
The Main Mode is the standard mode.
Default setting: Aggressive Mode
● Security statistics
Specifies whether the statistics of security events are sent to the master. Security events
are authentication requests to the CP. If the option is enabled, all authentication requests
with date, time and result are saved on the CP and sent to the master for further
evaluation.
Range of values:
– Do not send security statistics
– Send security statistics
Default setting: Do not send security statistics

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 65
Configuration
4.9 Security

● SHA-1 interlock
Setting to select whether the CP may use the secure hash algorithm SHA-1 if "SHA-256"
was configured as the Secure hash algorithm and the master does not support SHA-256.
Range of values:
– SHA-1 mode not allowed
The CP may not use SHA-1. If the master does not support SHA-256, no connection
will be established.
– SHA-1 mode allowed
The CP can use SHA-1 if the master does not support SHA-256.
Default setting: SHA-1 mode not allowed
● Secure hash algorithm (SHA)
Selection of the Secure Hash Algorithm (SHA)
Range of values:
– SHA-1
– SHA-256
Default setting: 256
● Key wrap algorithm
Selection of the Advanced Encryption Standard (AES)
Range of values:
– AES-128
– AES-256
Default setting: AES-128
● Key length
Specifies the length of the pre-shared key in bytes.
Permitted range: 16 - 128 Depending on the secure hash algorithm configured in STEP 7
above, the following lengths are preset:
– For SHA-1: 16
– For SHA-256: 32
The value 0 (zero) is not permitted.
● Max. number of statistics queries
If the configured number of statistics queries of the master is exceeded within the key
exchange interval, the CP enters a message in the diagnostics buffer of the CPU.
Range of values: 2...255 Default setting: 5

CP 1243-1
66 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

● Authentication requests before key exchange

Maximum number of authentication requests of the CP with the master. When this
number is reached, the session key is renewed.
Range of values: 1...10000 Default setting: 1000
Recommendation: Set the number for the CP twice as high as for the master.
● Key exchange interval
Period after which the key is exchanged again between the CP and the master. The
interval must be matched up on both communications partners.
Range of values: 0...65535 min. at 0 (zero), the key is never changed (function disabled).
Default setting: 15 min.
Recommendation: Set the key exchange interval for the CP twice as high as for the
master.
● Authentication timeout
Maximum waiting time for the response from the master to an authentication request of
the CP.
Exceeding the wait time is evaluated as an error by the CP. In this case, the CP
generates a security event and sends this to the master.
Range of values: 1... 65535 s Default setting: 5
● Pre-shared key
The pre-shared key can be configured in two ways:
– Manual configuration
Enter the pre-shared key in STEP 7 manually as a hexadecimal value.
– Import as file
Import the pre-shared key from the file system of the engineering station if the pre-
shared key was generated by the master or another engineering system.
The pre-shared key of the CP must be identical to the pre-shared key of the master.

4.9.4 Firewall

4.9.4.1 Pre-check of messages by the MAC firewall.

Each incoming or outgoing frame initially runs through the MAC firewall (layer 2). If the frame
is discarded at this level, it will not be checked by the IP firewall (layer 3). This means that
with suitable MAC firewall rules, IP communication can be restricted or blocked.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 67
Configuration
4.9 Security

4.9.4.2 Notation for the source IP address (advanced firewall mode)

If you specify an address range for the source IP address in the advanced firewall settings of
the CP, make sure that the notation is correct:
● Separate the two IP addresses only using a hyphen.
Correct: 192.168.10.0-192.168.10.255
● Do not enter any other characters between the two IP addresses.
Incorrect: 192.168.10.0 - 192.168.10.255
If you enter the range incorrectly, the firewall rule will not be used.

4.9.4.3 Firewall settings for configured connection connections via a VPN tunnel

IP rules in advanced firewall mode

If you set up configured connection connections with a VPN tunnel between the CP and a
communications partner, you will need to adapt the local firewall settings of the CP:
In advanced firewall mode ("Security > Firewall > IP rules") select the action "Allow*" for both
communications directions of the VPN tunnel.

See also
Settings for online security diagnostics and downloading to station with the firewall activated
(Page 68)

4.9.4.4 Settings for online security diagnostics and downloading to station with the firewall
activated

Setting the firewall for online functions

With the security functions enabled, follow the steps outlined below:
1. In the global security settings (see project tree), select the entry "Firewall > Services >
Define services for IP rules".
2. Select the "ICMP" tab.
3. Insert a new entry of the type "Echo Reply" and another of the type "Echo Request".
4. Now select the CP in the S7 station.
5. Enable the advanced firewall mode in the local security settings of the CP in the "Security
> Firewall" parameter group.
6. Open the "IP rules" parameter group.

CP 1243-1
68 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

7. In the table, insert a new IP rule for the previously created global services as follows:
– Action: Allow; "From external -> To station " with the globally created "Echo request"
service
– Action: Allow; "From station -> to external" with the globally created "Echo reply"
service
8. For the IP rule for the Echo Request, enter the IP address of the engineering station in
"Source IP address". This ensures that only ICMP frames (ping) from your engineering
station can pass through the firewall.

4.9.5 E-mail configuration

Configuring e-mails in STEP 7

With special events, e.g. CPU STOP, the CP can send e-mails. It does not depend on
whether telecontrol communication is used.
When using telecontrol communication, additionally configured events in the process image
of the CPU can trigger the sending of e-mails. Along with the e-mail process data can also
be sent.
You configure the individual e-mails in the message editor (entry "Messages"), see section
Messages (Page 113)

Requirements
The following requirements must be met in the configuration for sending e-mails:
● The security functions are enabled.
● The time of the CP is synchronized.
● In the "E-mail configuration" entry, the protocol to be used and the data for access to the
e-mail server are configured.

E-mail configuration
With the default setting of the SMTP port 25, the module transfers unencrypted e-mails.
If your e-mail service provider only supports encrypted transfer, use one of the following
options:
● Port no. 587
By using STARTTLS, the module sends encrypted e-mails to the SMTP server of your e-
mail service provider.
Recommendation: If your e-mail provider offers both options (STARTTLS / SSL/TLS), you
should use STARTTLS with port 587.
● Port no. 465
By using SSL/TLS (SMTPS), the module sends encrypted e-mails to the SMTP server of
your e-mail service provider.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 69
Configuration
4.9 Security

Ask your e.mail service provider which option is supported.

Importing the certificate with encrypted transfer

To be able to use encrypted transfer, you need to load the certificate of your e-mail account
in the certificate manager of STEP 7. You obtain the certificate from your e-mail service
provider.
Use the certificate by taking the following steps:
1. Save the certificate of your e-mail service provider in the file system of the engineering
station.
2. Import the certificate into your STEP 7 project with "Global security settings > Certificate
manager".
3. Use the imported certificate with every module that uses encrypted e-mails via the
"Certificate manager" table in the local "Security“ parameter group.
For the procedure, refer to the section Handling certificates (Page 72).

4.9.6 Log settings - Filtering of the system events

Communications problems if the value for system events is set too high
If the value for filtering the system events is set too high, you may not be able to achieve the
maximum performance for the communication. The high number of output error messages
can delay or prevent the processing of the communications connections.
In "Security > Log settings > Configure system events", set the "Level:" parameter to the
value "3 (Error)" to ensure the reliable establishment of the communications connections.

4.9.7 SNMP

SNMP
The range of functions of the CP for SNMP can be found in the section SNMP (Page 125).
If the security functions are enabled, you have the following selection and setting options.

SNMP
● "Enable SNMP"
If the option is enabled, communication via SNMP is released on the device. As default,
SNMPv1 is enabled.
If the option is disabled, queries from SNMP clients are not replied to either via SNMPv1
or via SNMPv3.

CP 1243-1
70 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

● "Use SNMPv1"
Enables the use of SNMPv1 for the CP. For information on the configuration of the
required community strings see below (SNMPv1).
● "Use SNMPv3"
Enables the use of SNMPv3 for the CP. For information on the configuration of the
required algorithms see below (SNMPv3).

SNMPv1
The community strings need to be sent along with queries to the CP via SNMPv1.
● "Reading community string"
The string is required for read access.
Leave the preset string "public" or configure a string.
● "Allow write access"
If the option is enabled write access to the CP is released and the corresponding
community string can be edited.
● "Writing community string"
The string is required for write access and can also be used for read access.
Leave the preset string "private" or configure a string.
Note the use of lowercase letters with the preset community strings!

SNMPv3
The algorithms need to be configured for encrypted access to the CP via SNMPv3.
● "Authentication algorithm"
Select the authentication method to be used from the drop-down list.
● "Encryption algorithm"
Select the encryption method to be used from the drop-down list.
Note the information on security of the possible algorithms in the online help of the SCT.

User management
In the user management that you will find in the global security settings, assign the various
users their role.
Below the properties of the roles you can see the rights list of the particular role, for example
the various types of access using SNMP. For new roles, you can freely configure individual
rights.
You will find information on users, roles and the password policy in the information system of
STEP 7.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 71
Configuration
4.9 Security

4.9.8 Certificate manager

Assignment of certificates
If you use communication with authentication for the module, for example SSL/TLS for
secure transfer of e-mails, certificates are required. You need to import certificates of non-
Siemens communications partners into the STEP 7 project and download them to the
module with the configuration data:
1. Import the certificates of the communications partners using the certificate manager in the
global security settings.
2. Then assign the imported certificates to the module in the table below the local security
settings of the module.
For a description of the procedure, refer to the section Handling certificates (Page 72).
You will find further information in the STEP 7 information system.

4.9.9 Handling certificates

Certificate for authentication

If you have configured secure communication with authentication for the CP, own certificates
and certificates of the communications partner will be required for communication to take
place.
All nodes of a STEP 7 project with enabled security functions are supplied with certificates.
The STEP 7 project is the certification authority.

Note
No certificate with security functions disabled.
If the security functions of the CP are disabled in the STEP 7 project, no certificate will be
generated for the CP.

For the secure transfer of e-mails via SSL/TLS and SSL certificate is created for the CP. It is
visible in STEP 7 in "Global security settings > Certificate manager > Device certificates".
The table "Device certificates" shows the issuer, validity, use of a certificate
(service/application) and the use of a key. You can call up further information about a
certificate by selecting the certificate in the table and selecting the shortcut menu "Show".
The table also shows all other certificates generated by STEP 7 and all imported certificates.

CP 1243-1
72 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

So that the CP can communicate with non-Siemens partners when the security functions are
enabled, the relevant certificates of the partners must be exchanged during communication.
To supply the CP with third-party certificates, follow the steps below:
1. Importing third-party certificates from communications partners
⇒ Global security settings of the project (certificate manager)
2. Assigning certificates locally
⇒ Local security settings of the CP ("Certificate manager" table)
These two steps are described in the next two sections.

Importing third-party certificates from communications partners

Import the certificates of the communications partners of third-party vendors using the
certificate manager in the global security settings. Follow the steps outlined below:
1. Save the third-party certificate in the file system of the PC of the connected engineering
station.
2. In the STEP 7 project open the global certificate manager:
Global security settings > Certificate manager
3. Open the "Trusted certificates and root certification authorities" tab.
4. Click in a row of the table can select the shortcut menu "Import".
5. In the dialog that opens, import the certificate from the file system of the engineering
station into the STEP 7 project.

Assigning certificates locally

To be able to use an imported certificate for the CP, you need to specify it in the "Security"
parameter group of the CP. Follow the steps outlined below:
1. In the STEP 7 project select the CP.
2. Navigate to the parameter group "Security > Certificate manager".
3. In the table, double-click on the cell with the entry "<Add new>".
The "Certificate manager" table of the Global security settings is displayed.
4. In the table. select the required third-party certificate and to adopt it click the green check
mark below the table.
The selected certificate is displayed in the local table of the CP.
Only now will the third-party certificate be used for the CP.

Exporting certificates for applications of third-party vendors (e.g. logging server)

For communication with applications of third-party vendors, the third-party application
generally also requires the certificate of the CP.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 73
Configuration
4.9 Security

You export the certificate of the CP for communications partners from third-party vendors in
much the same way as when importing (see above). Follow the steps outlined below:
1. In the STEP 7 project open the global certificate manager:
Global security settings > Certificate manager
2. Open the "Device certificates" tab.
3. In the table select the row with the required certificate and select the shortcut menu
"Export".
4. Save the certificate in the file system of the PC of the connected engineering station.
Now you can transfer the exported certificate of the CP to the system of the third-party
vendor.

Certificate for logging server

If you use a logging server in your system, export the SSL certificate for the authentication of
the CP on the server.

Change certificate: Subject Alternative Name

STEP 7 adopts the properties "DNS name", "IP address", and "URI" from the parameter
"Subject Alternative Name" (Windows: "Alternative applicant name") from the STEP 7
configuration data.
You can change this parameter of a certificate inn the certificate manager of the global
security settings. To do this, select the a certificate in the table of device certificates and call
the shortcut menu "Renew". Properties of the parameter "Alternative name of the certificate
owner" changed in STEP 7 are not adopted by the STEP 7 project.

4.9.10 VPN

4.9.10.1 VPN (Virtual Private Network)

VPN tunnel
Virtual Private Network (VPN) is a technology for secure transportation of confidential data in
public IP networks, for example the Internet. With VPN, a secure connection (tunnel) is set
up and operated between two secure IT systems or networks via a non-secure network.
One of the main features of the VPN tunnel is that it forwards all frames even from protocols
of higher layers (HTTP, FTP etc.).
The data traffic between two network components is transported practically unrestricted
through another network. This allows entire networks to be connected together via a
neighboring or intermediate network.

CP 1243-1
74 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

Properties
● VPN forms a logical subnet that is embedded in a neighboring (assigned) network. VPN
uses the usual addressing mechanisms of the assigned network, however in terms of the
data, it transports its own frames and therefore operates independent of the rest of this
network.
● VPN allows communication of the VPN partners with the assigned network.
● VPN is based on tunnel technology and can be individually configured.
● Communication between the VPN partners is protected from eavesdropping or
manipulation by using passwords, public keys or a digital certificate (authentication).

Areas of application
● Local area networks can be connected together securely via the Internet ("site-to-site"
connection).
● Secure access to a company network ("end-to-site" connection)
● Secure access to a server ("end-to-end" connection)
● Communication between two servers without being accessible to third parties (end-to-end
or host-to-host connection)
● Ensuring information security in networked automation systems
● Securing the computer systems including the associated data communication within an
automation network or secure remote access via the Internet
● Secure remote access from a PC/programming device to automation devices or networks
protected by security modules via public networks.

Cell protection concept

With Industrial Ethernet Security, individual devices or network segments of an Ethernet
network can be protected:
● Access to individual devices and network segments protected by security modules is
allowed.
● Secure connections via non-secure network structures becomes possible.
Due to the combination of different security measures such as firewall, NAT/NAPT routers
and VPN via IPsec tunnels, security modules protect against the following:
● Data espionage
● Data manipulation
● Unwanted access

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 75
Configuration
4.9 Security

4.9.10.2 Creating a VPN tunnel for S7 communication between stations

Requirements
To allow a VPN tunnel to be created for S7 communication between two S7 stations or
between an S7 station and an engineering station with a security CP (for example CP 1628),
the following requirements must be met:
● The two stations have been configured.
● The CPs in both stations must support the security functions.
● The Ethernet interfaces of the two stations are located in the same subnet.

Note
Communication also possible via an IP router
Communication between the two stations is also possible via an IP router. To use this
communications path, however, you need to make further settings.

Procedure
To create a VPN tunnel, you need to work through the following steps:
1. Creating a security user
If the security user has already been created: Log on as a user.
2. Select the "Activate security features" check box
3. Creating the VPN group and assigning security modules
4. Configure the properties of the VPN group
5. Configure local VPN properties of the two CPs
You will find a detailed description of the individual steps in the following paragraphs of this
section.

Creating a security user

To create a VPN tunnel, you require appropriate configuration rights. To activate the security
functions, you need to create at least one security user.
1. In the local security settings of the CP, click the "User login" button.
Result: A new window opens.
2. Enter the user name, password and confirmation of the password.
3. Click the "Logon" button.
You have created a new security user. The security functions are now available to you.
With all further logons, log on as user.

CP 1243-1
76 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

Select the "Activate security features" check box

After logging on, you need to select the "Activate security features" check box in the
configuration of both CPs.
You now have the security functions available for both CPs.

Creating the VPN group and assigning security modules

1. In the global security settings, select the entry "Firewall" > "VPN groups" > "Add new VPN
group".
2. Double-click on the entry "Add new VPN group", to create a VPN group.
Result: A new VPN group is displayed below the selected entry.
3. In the global security settings, double-click on the entry "VPN groups" > "Assign module
to a VPN group".
4. Assign the security modules between which VPN tunnels will be established to the VPN
group.

Note
Current date and current time on the CP for VPN connections
Normally, to establish a VPN connection and the associated recognition of the certificates to
be exchanged, the current date and the current time are required on both stations.
The establishment of a VPN connection to an engineering station that is also the telecontrol
server at the same time (TCSB installed), runs as follows along with the time of day
synchronization of the CP:
On the engineering station (with TCSB), you want the CP to establish a VPN connection.
The VPN connection is established even if the CP does not yet have the current time.
Otherwise the certificates used are evaluated as valid and the secure communication will
work.
Following connection establishment, the CP synchronizes its time of day with the PC
because the telecontrol server is the time master if telecontrol communication is enabled.

Configure the properties of the VPN group

1. Double-click on the newly created VPN group.
Result: The properties of the VPN group are displayed under "Authentication".
2. Enter a name for the VPN group. Configure the settings of the VPN group in the
properties.
These properties define the default settings of the VPN group that you can change at any
time.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 77
Configuration
4.9 Security

Note
Specifying the VPN properties of the CPs
You specify the VPN properties of the CPs in the "Security" > "Firewall" > "VPN" parameter
group of the relevant module.

Result
You have created a VPN tunnel. The firewalls of the CPs are activated automatically: The
"Activate firewall" check box is selected as default when you create a VPN group. You
cannot deselect the check box.
Download the configuration to all modules that belong to the VPN group.

4.9.10.3 VPN communication with SOFTNET Security Client (engineering station)

Setting up VPN tunnel communication between the SOFTNET Security Client and the CP is
essentially the same as described in Creating a VPN tunnel for S7 communication between
stations (Page 76).

VPN tunnel communication works only if the internal node is disabled

Under certain circumstances the establishment of VPN tunnel communication between
SOFTNET Security Client and the CP fails.
SOFTNET Security Client also attempts to establish VPN tunnel communication to a lower-
level internal node. This communication establishment to a non-existing node prevents the
required communication being established to the CP.
To establish successful VPN tunnel communication to the CP, you need to disable the
internal node.
Use the procedure for disabling the node as explained below only if the described problem
occurs.
Disable the node in the SOFTNET Security Client tunnel overview:
1. Remove the checkmark in the "Enable active learning" check box.
The lower-level node initially disappears from the tunnel list.
2. In the tunnel list, select the required connection to the CP.
3. With the right mouse button, select "Enable all members" in the shortcut menu.
The lower-level node appears again temporarily in the tunnel list.
4. Select the lower-level node in the tunnel list.
5. With the right mouse button, select "Delete entry" in the shortcut menu.
Result: The lower-level node is now fully disabled. VPN tunnel communication can be
established.

CP 1243-1
78 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

4.9.10.4 Creating the VPN connection telecontrol server

Configuration of a VPN connection between CP and TCSB

For secure communication via a VPN tunnel, the communications partners are assigned to a
common VPN group. The configuration of a VPN connection between CP and TCSB is not
directly possible because the telecontrol server cannot be configured in STEP 7.
To configure the communication between the CP 1243-1 and TCSB via a VPN connection,
follow the steps below:
● Create a PC station as a substitute for the telecontrol server.
This PC station serves as a placeholder for the telecontrol server only for configuration of
the security group and it is not required for any other purpose.
● To set up the security functions you then have the following alternative options:
– Install a CP 1628 (security module) on the computer of the telecontrol server and
assign the CP 1243-1 and the CP 1628 to the same security group in the
configuration.
– Install the SOFTNET Security Client (license required) on the computer of the
telecontrol server and configure the security functions in the STEP 7 project.
With both options you achieve the requirements at the TCSB end for secure communication
between the CPs of the remote station and the telecontrol server via secure VPN
connections.
Configure the security functions of the CPs as described above.

4.9.10.5 Establishment of VPN tunnel communication between the CP and SCALANCE M

Create a VPN tunnel between the CP and a SCALANCE M router as described for the
stations.
VPN tunnel communication will only be established if you have selected the check box
"Perfect Forward Secrecy" in the global security settings of the created VPN group ("VPN
groups > Authentication").
If the check box is not selected, the CP rejects establishment of the tunnel.

4.9.10.6 CP as passive subscriber of VPN connections

Setting permission for VPN connection establishment with passive subscribers

If the CP is connected to another VPN subscriber via a gateway, you need to set the
permission for VPN connection establishment to "Responder".
This is the case in the following typical configuration:
VPN subscriber (active) ⇔ gateway (dyn. IP address) ⇔ Internet ⇔ gateway (fixed IP
address) ⇔ CP (passive)

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 79
Configuration
4.9 Security

Configure the permission for VPN connection establishment for the CP as a passive
subscriber as follows:
1. In STEP 7, go to the devices and network view.
2. Select the CP.
3. Open the parameter group "VPN“ in the local security settings.
4. For each VPN connection with the CP as a passive VPN subscriber, change the default
setting "Initiator/Responder" to the setting "Responder".

4.9.10.7 SYSLOG

Use of SYSLOG only with 1 VPN connection

If you want to use SYSLOG with level 7 (debug) via Vpn connections, this is only possible
with a single established VPN connection.

4.9.11 Configuration of the TeleService access

Configuration for using TeleService

To meet the requirements for using the TeleService functions for the CP, you need to make
the necessary settings at the following points in STEP 7.

"Communication types" parameter group of the CP

Select the following options:
● Enable telecontrol communication
● Activate online functions

Telecontrol server under "Partner stations" of the CP

You configure the following information here:
● Address of the telecontrol server
IP address or name of the telecontrol server that can be resolved by DNS.
● Port
Port number of the telecontrol server

CP 1243-1
80 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.9 Security

Users and roles in the global security settings

1. Open the following page in the project tree:
Global security settings > User management
2. Role
Open the "Roles" tab
The two tables "Roles" and "Rights of the role" become visible.
If necessary open the "Roles view" if this is hidden by the "Rights of the role" table.
In the "Roles" table (at the top) create a new user-defined role for TeleService.
3. In the "User" tab create a user that will later be allowed to execute the TeleService
functions for the CP.
Configure the following parameters:
– User name
Assign the name of the user that will have TeleService rights.
You require the user name at the start of a TeleService session.
– Authentication method
Select the authentication method "Password" for this user.
– Password
Assign the password.
You require the password at the start of a TeleService session.
Note:
You specify the password properties of the security functions in the "Password
policies" tab.
You enter the password on the engineering station when starting a TeleService
session.
– Maximum time of the session
The time that can be configured here is only required for access to SCALANCE S
modules. If the user is set up only for TeleService sessions, you can leave the default
value unchanged.
4. Click on the "Roles" tab.
5. Select the CP in the lower list "Rights of the role" under the "Module rights" group.
6. The available rights are displayed in the "List of rights" table.
The right "Use TeleService" is displayed.
7. Enable the "Use TeleService" right for the module.
8. Following this, set the S7 protocol to "allow" in Firewall.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 81
Configuration
4.10 Data points

4.10 Data points

4.10.1 Data point configuration

Data point-related communication with the CPU

No program blocks need to be programmed for telecontrol modules with data point
configuration to transfer user data between the station and communications partner.
The data areas in the memory of the CPU intended for communication with the
communications partner are configured data point-related on the module. Each data point is
linked to a PLC tag or the tag of a data block.

Requirement: Created PLC tags and/or data blocks (DBs)

PLC tags or DBs must first be created in the CPU program to allow configuration of the data
points.
The PLC tags for data point configuration can be created in the standard tag table or in a
user-defined tag table. All PLC tags intended to be used for data point configuration must
have the attribute "Visible in HMI".
Address areas of the PLC tags are input, output or bit memory areas on the CPU.

Note
Number of PLC tags
Remember the maximum possible number of PLC tags the can be used for data point
configuration in the section Configuration limits and performance data (Page 15).

The formats and S7 data types of the PLC tags that are compatible with the protocol-specific
data point types of the module can be found in the section Datapoint types (Page 89).

Access to the memory areas of the CPU

The values of the PLC tags or DBs referenced by the data points are read and transferred to
the communications partner by the module.
Data received from the communications partner is written by the module to the CPU via the
PLC tags or DBs.

Configuring the data points and messages in STEP 7

You configure the data points in STEP 7 in the data point and message editor. You can find
this using the project tree:
Project > directory of the relevant station > Local modules > CP

CP 1243-1
82 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Figure 4-1 Configuring data points and messages

By double-clicking on the entry, the data point or message editor.

Using the two entries to the right above the table, you can switch over between the data
point and message editor.

Figure 4-2 Switching over between the two editors

Creating obects
With the data point or message editor open, create a new object (data point / message) by
double clicking "<Add object>" in the first table row with the grayed out entry.
A preset name is written in the cell. You can change the name to suit your purposes but it
must be unique within the module.

Figure 4-3 Data point table

You configure the remaining properties of every object using the drop-down lists of the other
table columns and using the parameter boxes shown at the bottom of the screen.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 83
Configuration
4.10 Data points

Assigning data points to their data source

After creating it, you assign a new data point to its data source. Depending on the data type
of the data point a PLC tag can serve as the data source.
For the assignment you have the following options:
● Click on the table symbol in the cell of the "PLC tag" column.
All configured PLC tags and the tags of the created data blocks are displayed. Select the
required data source with the mouse or keyboard.
● Click the symbol .
A selection list of the configured PLC Tags and the blocks is displayed. From the relevant
table, select the required data source.
● In the name box of the PLC tag, enter part of the name of the required data source.
All configured PLC tags and tags of the data blocks whose names contain the letters you
have entered are displayed.

Select the required data source.

Note
Assignment of parameter values to PLC tags
The mechanisms described here also apply when you need to assign the value of a
parameter to a PLC tag. The input boxes fro the PLC tag (e.g.: PLC tag for partner status
support the functions described here for selecting the PLC tag.

Arranging and copying objects

As with many other programs in the data point or message editor you can also arrange the
columns, sort the table according to your requirements and copy and insert objects.
● Arrange columns
If you click on a column header with the left mouse button pressed, you can move the
column.
● Sorting objects
If you click briefly with the left mouse button on a column header, you can sort the objects
of the table in ascending or descending order according to the entries in this column. The
sorting is indicated by an arrow in the column header.
After sorting in descending order of a column the sorting can be turned off by clicking on
the column header again.

CP 1243-1
84 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

● Adapting the column width

You can reach this function with the following actions:
– Using the shortcut menu that opens when you click on a column header with the right
mouse key.
"Optimize width", "Optimize width of all columns"
– If you move the cursor close to the limit of a column header, the following symbol
appears:

When it does, click immediately on the column header. The column width adapts itself
to the broadest entry in this column.
● Showing / hiding columns
You call this function using the shortcut menu that opens when you click on a column
header with the right mouse key.
● Copying, pasting, cutting and deleting objects
If you click in a parameter box of an object in the table with the right mouse key, you can
use the functions named with the shortcut menu (copy, paste, cut, delete).
You can paste cut or copied objects within the table or in the first free row below the
table.

Exporting and importing data points

To simplify the engineering of larger plants, you can export the data points of a configured
module and import them into other modules in the project. This is an advantage particularly
in projects with many identical or similar stations or data point modules.
The export / import function is available when you select the module for example in the
network or device view and select the relevant shortcut menu.

Figure 4-4 Shortcut menu of the module

When it is exported the data point information of a module is written to a CSV file.

Export
When you call the export function, the export dialog opens. Here, you select the module or
modules of the project whose data point information needs to be exported. When necessary,
you can export the data points of all modules of the project at one time.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 85
Configuration
4.10 Data points

In the export dialog, you can select the storage location in the file directory. When you export
the data of a module you can also change the preset file name.
When you export from several modules, the files are formed with preset names made up of
the station name and module name.
The file itself contains the following information in addition to the data point information:
● Module name
● Module type
● CPU name
● CPU type

Editing the data point information

You can edit the data point information in an exported CSV file. This allows you to use this
file as a configuration template for many other stations.
If you have a project with many stations of the same type, you can copy the CSV file with the
data points of a fully configured module for other as yet unconfigured stations and adapt
individual parameters to the particular station. This saves you having to configure the data
points for every module in STEP 7. Instead, you simply import the copied and adapted CSV
file to the other modules of the same type. When you import this file into another module, the
changed parameter values of the CSV file are adopted in the data point configuration of this
module.
The lines of the CSV file have the following content:
● Line 1: ,Name,Type,
This line must not be changed.
● Line 2: PLC,<CPU name>, <CPU type>,
Meaning: PLC (designation of the station class), CPU name, CPU type
Only the elements <CPU name> and <CPU type> may be changed.
The CPU type must correspond exactly to the name of the CPU in the catalog.
● Line 3: Module,<module name>, <module type>,
Meaning: Module (Designation of the module class), module type, module name
Only the elements <module name> and <module type> may be changed.
Be careful when changing the module names if you want to import data points into
several modules (see below).
The module type must correspond exactly to the name of the module in the catalog.
● Line 4: Parameter names (English) of the data points
This line must not be changed.
● Lines 5..n: Values of the parameters according to line 4 of the individual data points
You can change the parameter values for the particular station.

CP 1243-1
86 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Importing into a module

Before importing the data points make sure that the PLC tags required for the data points
have been created.
Note that when you import a CSV file all the data points existing on the module will be
deleted and replaced by the imported data points.
Select a module and select the import function from the shortcut menu of the module. The
import dialog opens in which you select the required CSV file in the file directory.
If the information on the assignment of the individual data points to the relevant PLC tags
matches the assignment in the original module, the data points will be assigned to the
corresponding PLC tags.
When you import data points into a module, but some required PLC tags have not yet been
created in the CPU, the corresponding data point information cannot be assigned. In this
case, you can subsequently create missing PLC tags and them assign them the imported
data point information. The "Assignment repair" function is available for this (see below).
If the names of the PLC tags in the module into which the import is made have different
names than in the module that exported, the corresponding data points cannot be assigned
to your PLC tags.

Importing into several modules

You can import the data points from several modules into the modules of a different project.
To do this in the import dialog select all the required CSV files with the control key.
Before importing the data points, make sure that the respective stations have been created
with CPUs of the same name, modules of the same name and PLC tags of the same name.
When you import the corresponding stations of the project are searched for based on the
module names in the CSV files. If a target station does not exist in the project or the module
has a different name, the import of the particular CSV file will be ignored.

Restrictions for the import of data points

In the following situations the import of data points will be aborted:
● An attribute required by the module is missing in the CSV file to be imported.
Example: If a data point to be imported uses a time trigger, the import will be aborted if no
time-of-day synchronization was configured for the module.
● The telecontrol protocol used by the module differs from that of the original module.
Only when importing into several modules:
● The import is aborted when a module or CPU name is different from the data in the CSV
file.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 87
Configuration
4.10 Data points

Note:
Modules with the same telecontrol protocol are compatible with each other:
● TeleControl Basic
All SIMATIC NET modules with the TeleControl Basic protocol:
CP 1243-1, CP 1242-7 GPRS V2, CP 1243-7 LTE, CP 1542SP-1 IRC
● ST7
CP 1243-8 IRC, TIM modules capable of ST7
● DNP3
CP 1243-1, CP 1243-8 IRC, TIM modules capable of DNP3
● IEC
CP 1243-1, CP 1243-8 IRC
Data points can be imported and exported between compatible modules.

Assignment repair
If you have named the PLC tags in a station into which you want to import differently from
the station from which the CSV file was exported, the assignment between data point and
PLC tag is lost when you import.
You then have the option to either rename the existing PLC tags appropriately or add
missing PLC tags. You can then repair the assignment between unassigned data points and
PLC tags. This function is available either via the shortcut menu of the module (see above)
or with the following icon to the upper left in the data point editor:
If a PLC tag with a matching name is found for a data point by the repair function, the
assignment is restored. However the data type of the tag is not checked.
After the assignment repair make sure that you check whether the newly assigned PLC tags
are correct.

4.10.2 Syntax of the data point names

Character set for data point names

When you create a data point, a preset name "DataPoint_n" is adopted. In the data point
table and in the "General" tab of the data point you can change the name of the data point.
When assigning names only ASCII characters from the band 0x20 ... 0x7e (no. 32-126) may
be used with the exceptions listed below.
Forbidden characters:
● .'[]/\|
period, apostrophe, square brackets, slash, back slash, vertical line (pipe)

CP 1243-1
88 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

4.10.3 Datapoint types

Configure the user data to be transferred from the CPU that is referenced via PLC tags of
the CPU on the CP as data points.
The data point types supported by the CP along with the compatible S7 data types are listed
below for the various telecontrol protocols.
The direction relates to the direction of transfer:
● "in": Monitoring direction:
● "out": Control direction

Note
Effect of the change of arrays for data points
If an array is modified later, the data point must be recreated.

Data point types of the "TeleControl Basic" protocol

Table 4- 1 Supported data point types and compatible S7 data types

Format (memory requirements) Data point type Direction S7 data types Operand area
Bit Digital input in Bool I, Q, M, DB
Digital output in Bool Q, M, DB
Byte Digital input in Byte, Char, USInt I, Q, M, DB
Digital output out Byte, Char, USInt Q, M, DB
Integer with sign (16 bits) Analog input in Int I, Q, M, DB
Analog output out Int Q, M, DB
Counter (16 bits) Counter input in Word, UInt I, Q, M, DB
Integer with sign (32 bits) Analog input in DInt Q, M, DB
Analog output out DInt Q, M, DB
Counter (32 bits) Counter input in UDInt, DWord I, Q, M, DB
Floating-point number with sign (32 Analog input in Real Q, M, DB
bits) Analog output out Real Q, M, DB
Floating-point number with sign (64 Analog input out LReal Q, M, DB
bits) Analog output out LReal Q, M, DB
Data block (1 .. 64 bytes) Data in / out ARRAY 1) DB
Data in / out ARRAY 1) DB
1) For the possible formats of the ARRAY data type, refer to the following section.

Block of data (ARRAY)

With the ARRAY data type, contiguous memory areas up to a size of 64 bytes can be
transferred. The following S7 data types are compatible components of ARRAY:
● Byte, USInt (total of up to 64 per data block)
● Char (total of up to 64 per data block) - CP as of firmware version 2.1.77

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 89
Configuration
4.10 Data points

● Int, UInt, Word (total of up to 32 per data block)

● DInt, UDInt, DWord (total of up to 16 per data block)
If the array is modified later, the data point must be recreated.

Format of the time stamp

Time stamps are output by the OPC server applications in UTC format (48 bits) and contain
milliseconds.

Data point types of the "DNP3" protocol

Table 4- 2 Supported data point types, DNP3 object groups, variants and compatible S7 data types

Format (memory require- Data point type CP DNP3 object Direction S7 data types Operand area
ments) [Data point type TIM] group
[variations]
Bit Binary Input 1 [1, 2] in Bool I, Q, M, DB
Binary Input Event 2 [1, 2] in Bool I, Q, M, DB
Binary Output 1) 10 [2] out Bool Q, M, DB
Binary Output Event 1) 11 [1, 2] out Bool Q, M, DB
Binary Command 12 [1] out Bool Q, M, DB
Integer (16 bits) Counter Static 20 [2] in UInt, Word I, Q, M, DB
Frozen Counter 2) 21 [2, 6] in UInt, Word I, Q, M, DB
Counter Event 22 [2, 6] in UInt, Word I, Q, M, DB
Frozen Counter 23 [2, 6] in UInt, Word I, Q, M, DB
Event 3)
Analog Input 30 [2] in Int I, Q, M, DB
Analog Input Event 32 [2] in Int I, Q, M, DB
Analog Output Sta- 40 [2] out Int Q, M, DB
tus 4)
Analog Output 41 [2] out Int Q, M, DB
Analog Output 42 [2, 4] out Int Q, M, DB
Event 4)
Integer (32 bits) Counter Static 20 [1] in DWord I, Q, M, DB
Frozen Counter 2) 21 [1, 5] in DWord I, Q, M, DB
Counter Event 22 [1, 5] in DWord I, Q, M, DB
Frozen Counter 23 [1, 5] in DWord I, Q, M, DB
Event 3)
Analog Input 30 [1] in DInt Q, M, DB
Analog Input Event 32 [1] in DInt Q, M, DB
Analog Output Sta- 40 [1, 3] out DInt Q, M, DB
tus 4)
Analog Output 41 [1] out DInt Q, M, DB
Analog Output 42 [1] out DInt Q, M, DB
Event 4)

CP 1243-1
90 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Format (memory require- Data point type CP DNP3 object Direction S7 data types Operand area
ments) [Data point type TIM] group
[variations]
Floating-point number (32 Analog Input 30 [5] in Real Q, M, DB
bits) Analog Input Event 32 [5, 7] in Real Q, M, DB
Analog Output Sta- 40 [3] out Real Q, M, DB
tus 4)
Analog Output 41 [3] out Real Q, M, DB
Analog Output 42 [5, 7] out Real Q, M, DB
Event 4)
Floating-point number (64 Analog Input 30 [6] in LReal Q, M, DB
bits) Analog Input Event 32 [6, 8] in LReal Q, M, DB
Analog Output 41 [4] out LReal Q, M, DB
Analog Output 42 [6, 8] out LReal Q, M, DB
Event 4)
Data block (1...64 Octet String / Oc- 110 [ - ] in, out 5) DB
bytes) 5) tet String Output
Octet String Event 5) 111 [ - ] in, out 5) DB
1) This object group can be configured in the Data point editor of STEP 7 using the substitute object group 12.
2) This object group can be configured in the Data point editor of STEP 7 using the substitute object group 20.
3) This object group can be configured in the Data point editor of STEP 7 using the substitute object group 22.
4) This object group can be configured in the Data point editor of STEP 7 using the substitute object group 41.
5) With these data point types, contiguous memory areas up to a size of 64 bytes can be transferred. All S7 data types with
a size between 1 and 64 bytes are compatible.

Substitute object groups (of the table footnotes 1), 2), 3), 4))
The initial data point types of the following object groups can be configured using the
substitute object groups listed above:
● 10 [2]
● 11 [1, 2]
● 21 [1, 2, 5, 6]
● 23 [1, 2, 5, 6]
● 40 [1, 2, 3]
● 42 [1, 2, 4, 5, 6, 7, 8]
To configure the DNP3 CP, use the specified substitute object group.
Assign each data point on the master using the configurable data point index in STEP 7. The
data point of the DNP3 CP is then assigned to the corresponding data point on the master.
Example of configuring the data point Binary Output (10 [2])
The data point is configured as follows:
On the DNP3 CP as Binary Command (12 [1])
On the master as Binary Output (10 [2])
With the data point types Binary Output Event (11) and Analog Output Event (42), you also
need to enable mirroring; refer to the next section.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 91
Configuration
4.10 Data points

Configuration of the mirroring back for output events (object groups 11 and 42)
You first create the data point types Binary Output Event (object group 11) and Analog
Output Event (object group 42) as described above as data points of the object groups 12 or
41.
The local values of these two object groups can be monitored for change and the changes
transferred to the master (). Changing a local value can, for example, be caused by manual
operator input on site.
To allow the value resulting from local events or interventions to be transferred to the master,
the data point in question requires a channel for mirroring back. You configure this mirroring
back function is configured using the "Value monitoring" option in data point configuration,
General tab.
Remember that to use the mirror back function, you need to interconnect the local values in
the controller with the relevant PLC tag of the data point.

Format of the time stamp

Time stamps are transferred in UTC format (48 bits) and contain milliseconds.

Data point types of the "IEC" protocol

Table 4- 3 Supported data point types, IEC types and compatible S7 data types

Format (memory Data point type IEC type Direction S7 data types Operand area
requirements)
Bit Single-point information <1> in Bool I, Q, M, DB
Single-point information with time tag <30> in Bool I, Q, M, DB
CP56Time2a 1)
Single command <45> out Bool Q, M, DB
Single command with time tag <58> out Bool Q, M, DB
CP56Time2a 1)
Double command with time tag <59> out Bool Q, M, DB
CP56Time2a 1)
Byte Step position information <5> in Byte, USInt I, Q, M, DB
Step position information with time <32> in Byte, USInt I, Q, M, DB
tag CP56Time2a 1)
Regulating step command with time <60> out Byte, USInt Q, M, DB
tag CP56Time2a 1)
Integer (16 bits) Measured value, normalized value <9> in Int I, Q, M, DB
Measured value, normalized value <34> in Int I, Q, M, DB
with time tag CP56Time2a 1)
Measured value, scaled value <11> in Int I, Q, M, DB
Measured value, scaled value with <35> in Int I, Q, M, DB
time tag CP56Time2a 1)
Set point command, normalised <48> out Int Q, M, DB
value
Set point command, scaled value <49> out Int Q, M, DB
Set point command, normalised <61> out Int Q, M, DB
value with time tag CP56Time2a 1)
Set point command, scaled value <62> out Int Q, M, DB
with time tag CP56Time2a 1)

CP 1243-1
92 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Format (memory Data point type IEC type Direction S7 data types Operand area
requirements)
Integer (32 bits) Bitstring of 32 bits <7> in UDInt, DWord I, Q, M, DB
Bitstring of 32 bits with time tag <33> in UDInt, DWord I, Q, M, DB
CP56Time2a 1)
Integrated totals <15> in UDInt, DWord I, Q, M, DB
Integrated totals with time tag <37> in UDInt, DWord I, Q, M, DB
CP56Time2a 1)
Bitstring of 32 bits <51> out UDInt, DWord Q, M, DB
Bitstring of 32 bits with time tag <64> out UDInt, DWord Q, M, DB
CP56Time2a 1)
Floating-point Measured value, short floating point <13> in Real Q, M, DB
number (32 bits) number
Measured value, short floating point <36> in Real Q, M, DB
number with time tag CP56Time2a 1)
Set point command, short floating <50> out Real Q, M, DB
point number
Set point command, short floating <63> out Real Q, M, DB
point with time tag CP56Time2a 1)
Data block Double-point information <3> in 2) DB
(1...2 Bit) 2) Double-point information with time <31> in 2) DB
tag CP56Time2a 1)
Double command <46> out 2) DB
Regulating step command <47> out 2) DB
Double command with time tag <59> out 2) DB
CP56Time2a 1)
Regulating step command with time <60> out 2) DB
tag CP56Time2a 1)
Data block Bitstring of 32 bits 3) <7> in 3) DB
(1...32 Bit) 3)
Bitstring of 32 bits with time tag <33> in 3) DB
CP56Time2a 1) 3)
Bitstring of 32 bits 3) <51> out 3) DB
Bitstring of 32 bits with time tag <64> out 3) DB
CP56Time2a 1) 3)
1) For the format of the time stamp, see the following section.
2) For these data point types, create a data block with an array of precisely 2 bool.
3) With these data point types, contiguous memory areas up to a size of 32 bits can be transferred. Only the S7 Bool data
type is compatible.

Format of the time stamp

Time stamps are transferred according to the IEC specification in the "CP56Time2a" format.
Note that in the frames only the first 3 bytes for milliseconds and minutes are transferred.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 93
Configuration
4.10 Data points

4.10.4 Configuration of the data point index

Configuration of the data point index

Below you will find the rules for configuring the data point index.

Data point index with the TeleControl Basic protocol

Within a CP, the indexes of the data point classes must comply with the following rules:
● Input
The index of an input data point must be unique throughout all data point types (digital
inputs, analog inputs etc.).
● Output
The index of an output data point must be unique throughout all data point types (digital
inputs, analog inputs etc.).

Note
Index for data points with inter-station communication
Note that for inter-station communication with a CP in another S7 station, the indexes of the
two corresponding data points (data point pair) must be identical on the sending and
receiving CP.
For information on the configuration, refer to the section Partner configuration with
TeleControl Basic data points. (Page 112).

Data point index with the DNP3 protocol

On a CP, data point indexes must be unique within each of the following object groups:
● Binary Input / Binary Input Event
● Binary Output / Binary Command
● Counter / Counter Event
● Analog Input / Analog Input Event
● Analog Output
● Octet String / Octet String Event
Indexes of two data points in different object groups can be identical.

Data point index with the IEC protocol

The data point indexes must be unique in a CP.
Data point indexes assigned twice are indicated as errors in the consistency check and
prevent the project being saved.

CP 1243-1
94 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

4.10.5 Status IDs of the data points

Status identifiers
The status identifiers of the data points listed in the following tables are transferred along
with the value in each frame to the communications partner. They can be evaluated by the
communications partner.
The entries in the table row "Significance" relate to the entry in the table row "Bit status".

Generation of events if a data point status changes

With data points that were configured as an event, the change to the status bit of the status
identifiers described below also leads to an event being generated.
Example: If the value of the status "RESTART" of a data point configured as an event
changes form 1 (value not yet updated) to 0 (value updated) when the station starts up, this
causes an event to be generated.

Status identifiers with the TeleControl Basic protocol

Depending on their status, the status bits (see table) are converted to the OPC quality code
by TCSB.
● Quality = BAD
Bit 2 or 7 = 1
● Quality = UNCERTAIN
Bit 1 or 3 or 5 = 1
● Quality = GOOD
Bits 1 and 2 and 3 and 5 and 6 = 0
Table 4- 4 Bit assignment of status byte 0

Bit 7 6 5 4 3 2 1 0
Flag name - NON_ Substituted LOCAL_ CARRY OVER_ RESTART ONLINE
EXISTENT FORCED RANGE
Meaning - Data point Substitute Local opera- Counted Limit value Value not Value is
does not value tor control value over- of the ana- yet updated valid
exist or S7 flow before log prepro- after start
address reading the cessing
unreachable value overshot /
undershot
Bit status (always 1 1 1 1 1 1 1
0)

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 95
Configuration
4.10 Data points

Status identifiers with the DNP3 protocol

The status IDs correspond to the following elements of the specification:
OBJECT FLAGS - DNP3 Specification, Volume 6, Data Object Library - Part 1
Table 4- 5 Bit assignment of the status byte

Bit 7 6 5 4 3 2 1 0
Flag name - - - LOCAL_ DISCONTI OVER_ RESTART ONLINE
FORCED NUITY RANGE
Meaning - - - Local opera- Counted Limit value of Value not yet Value is valid
tor control value over- the analog updated after
flow before prepro- start
reading the cessing over-
value shot /
undershot
Bit status (always (always (always 1 1 1 1 1
0) 0) 0)

Status identifiers with the IEC protocol

The status IDs correspond to the following elements of the specification:
Quality descriptor - IEC 60870 Part 5-101
Table 4- 6 Bit assignment of the status byte

Bit 7 6 5 4 3 2 1 0
Flag name - - SB - CY OV NT IV
substituted carry overflow not topical invalid
Meaning - - Substitute - Counted Value range Value not Value is valid
value value over- exceeded, updated
flow before analog value
reading the
value
Bit status (always (always 1 (always 1 1 1 0
0) 0) 0)

4.10.6 Read cycle

Priority of the data points

The cyclic reading of the values of input data points from their assigned PLC tags on the
CPU can be prioritized.
Less important input data points do not need to be read in every CPU scan cycle. Important
input data points, on the other hand, can be prioritized for updating in every CPU scan cycle.

CP 1243-1
96 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

You can prioritize the data points in STEP 7 in the data point configuration in the "General"
tab with the "Read cycle" parameter. There you will find the two following options for input
data points:
● Fast cycle
● Normal cycle
The data points are read according to the method described below.

Structure of the CPU scan cycle

The cycle (including the pause) with which the CP scans the memory area of the CPU is
made up of the following phases:
● High-priority read jobs
The values of input data points with the scan priority "High-priority" are read in every scan
cycle.
● Low priority read jobs
Some of the values of input data points with the scan priority "Low-priority" are read in
every scan cycle.
The number of values read per cycle is specified for the CP in the "Communication with
the CPU" parameter group with the "Max. number of read jobs" parameter. The values
that exceed this value and can therefore not be read in one cycle are then read in the
next or one of the following cycles.
● Write jobs
In every cycle, the values of a certain number of unsolicited write jobs are written to the
CPU. The number of values written per cycle is specified for the CP in the
"Communication with the CPU" parameter group with the "Max. number of write jobs"
parameter. The values whose number exceeds this value are then written in the next or
one of the following cycles.
● Cycle pause time
This is the waiting time between two scan cycles. It is used to reserve adequate time for
other processes that access the CPU via the backplane bus of the station.

4.10.7 Process image, type of transmission, event classes, triggers

Saving the data point values

The values of data points are stored in the image memory of the CP and transferred only
when queried by the communications partner.
Events are also stored in the frame memory (send buffer) and can be transferred unsolicited.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 97
Configuration
4.10 Data points

Data points are configured as a static value or as an event using the "Type of transmission"
parameter (see below):
● Transfer after call: No event / static value
Static values are entered in the image memory (process image of the CP).
● Triggered: event
The values of data points configured as an event are also entered in the image memory
of the CP.
The values of events are also entered in the send buffer of the CP.
With DNP3, the value of the event is sent unsolicited to the communications partner if this
function is enabled by the master.

The image memory, the process image of the CP

The image memory is the process image of the CP. All the current values of the configured
data points are stored in the image memory. New values of a data point overwrite the last
stored value in the image memory.
The values are sent after querying the communications partner, see "Transfer after call" in
the section "Types of transmission" below.

The send buffer (frame memory)

The send buffer of the CP is the memory for the individual values of data points that are
configured as an event. The maximum size of the send butter can be found in the section
Configuration limits and performance data (Page 15).
The configured number of events is divided equally among all configured and enabled
communications partners. For information on the configuration, refer to the parameter
"Frame memory size" in the section SNMP (Page 53).
If the connection to a communications partner is interrupted, the individual values of the
events are stored in the RAM of the CP. When the connection returns, the buffered values
are sent. The frame memory operates chronologically; in other words, the oldest frames are
sent first (FIFO principle).
If a frame was transferred to the communications partner, the transferred values are deleted
from the send buffer.
If frames cannot be transferred for a longer period of time and the send buffer is threatening
to overflow, the response is as follows:

The forced image mode with TeleControl Basic

If the send buffer reaches a fill level of 80%, the CP changes to the forced image mode. New
values of events are no longer added to the send buffer but rather they overwrite older
existing values in the image memory.
When the connection to the communications partner returns, the CP changes back to the
send buffer mode as soon as the fill level of the send buffer has fallen below 50%.

CP 1243-1
98 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Types of transmission / event classes

The following types of transmission are possible:
● Transfer after call
The current value of the data point is entered in the image memory of the CP. New
values of a data point overwrite the last stored value in the image memory.
After being called by the communications partner, the current value at the time is
transferred.
● Triggered (event)
The values of data points configured as an event are entered in the image memory and
also in the send buffer of the CP.
The values of events are saved in the following situations:
– The configured trigger conditions are fulfilled (data point configuration > "Trigger" tab,
see below)
– The value of a status bit of the status identifiers of the data point changes see also the
section Status IDs of the data points (Page 95).
Example: When the value of a data point configured as an event is updated during
startup of the station by reading the CPU data for the first time, the status "RESTART"
of this data point changes (bit status change 1 → 0). This leads to generation of an
event.
When data points are configured as an event via the "Type of transmission" parameter,
the following event classes are available:
– Every value triggered
Each value change is entered in the send buffer in chronological order.
– Current value triggered
Only the last current value is entered in the send buffer. It overwrites the value stored
there previously.

Trigger

Trigger types
Various trigger types are available for event-driven transfer:
● Threshold value trigger
The value of the data point is transferred when this reaches a certain threshold. The
threshold is calculated as the difference compared with the last stored value, refer to the
section Threshold value trigger (Page 101).
● Time trigger
The value of the data point is transferred at configurable intervals or at a specific time of
day.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 99
Configuration
4.10 Data points

● Event trigger
The value of the data point is transferred when a configurable trigger signal is fired. As
the trigger signal, the edge change (0 → 1) of a trigger bit is evaluated that is set by the
user program. When necessary, a separate trigger bit can be configured for each data
point.
Resetting the trigger tag in the bit memory area / DB:
If the memory area of the trigger tag is in the bit memory or in a data block, the trigger tag
is reset to zero when the data point value is transferred.

Transmission time of the frame (Transmission mode)

Whether the value of a data point is transferred to the communications partner immediately
after the trigger fires or after a delay depends on the setting of the parameter "Transmission
mode" in the "Trigger" tab of the data point:
● Spontaneous
The value is transferred immediately.
● Conditional spontaneous
The value is transferred only when one of the two following conditions is fulfilled:
– The telecontrol server queries the station.
– The value of another event with the transmission mode "Unsolicited" is transferred.

4.10.8 "Trigger“ tab

Trigger
Data points are configured as a static value or as an event using the "Type of transmission"
parameter:

Saving the value of a data point configured as an event

Saving the value of a data point configured as an event in the send buffer (message
memory) can be triggered by various trigger types:
● Threshold value trigger
The value of the data point is saved when this reaches a certain threshold. The threshold
is calculated as the difference compared with the last stored value, refer to the section
Threshold value trigger (Page 101).
● Time trigger
The value of the data point is saved at configurable intervals or at a specific time of day.
● Event trigger (Trigger tag)
The value of the data point is saved when a configurable trigger signal is fired. For the
trigger signal, the edge change (0 → 1) of a trigger tag is evaluated that is set by the user
program. When necessary, a separate trigger tag can be configured for each data point.

CP 1243-1
100 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Resetting the trigger tag in the bit memory area / DB:

If the memory area of a trigger tag is in the bit memory or in a data block, the CP resets
the trigger variable itself to 0 (zero) as soon as the value of the data point has been
transferred. This can take up to 500 milliseconds.

Note
Fast setting of triggers
Triggers must not be set faster than a minimum interval of 500 milliseconds. This also
applies to hardware triggers (input area).

Note
Hardware trigger
You need to reset hardware triggers via the user program

Transferring the value of a data point configured as an event

You specify whether the value of a data point is transferred to the communications partner
immediately after the trigger fires or after a delay in the "Transmission mode" parameter.

Transmission mode
The transmission mode of a frame is set in the "Trigger" tab of the data point. With the
option, you specify whether messages of events are sent immediately or following a delay:
● Immediate transfer - Spontaneous
The value is transferred immediately.
● Buffered transfer - Conditionally spontaneous
The value is transferred only when one of the following conditions is fulfilled:
– The communications partner queries the station.
– The value of another event with the transmission mode “Spontaneous" is transferred.

4.10.9 Threshold value trigger

Note
Threshold value trigger: Calculation only after "Analog value preprocessing"
Note that the analog value preprocessing is performed before the check for a configured
threshold value and before calculating the threshold value.
This affects the value that is configured for the threshold value trigger.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 101
Configuration
4.10 Data points

Note
No Threshold value trigger if Mean value generation is configured
If mean value generation is configured, no threshold value trigger can be configured for the
analog value event involved.

For the time sequence of the analog value preprocessing refer to the section Analog value
preprocessing (Page 103).

Threshold value trigger

Function
If the process value deviates by the amount of the threshold value, the process value is
saved.
Two methods are used to calculate the threshold value deviation:
● Absolute method
With binary and counter values as well as with analog values with configured mean value
generation, the absolute method is used to calculate the threshold value deviation.
● Integrative method
With analog values without configured mean value generation, the integrating method is
used to calculate the threshold value deviation.
In the integration threshold value calculation, it is not the absolute value of the deviation
of the process value from the last stored value that is evaluated but rather the integrated
deviation.

Absolute method
For each binary value a check is made to determine whether the current (possibly smoothed)
value is outside the threshold value band. The current threshold value band results from the
last saved value and the amount of the configured threshold value:
● Upper limit of the threshold value band: Last saved value + threshold value
● Lower limit of the threshold value band: Last saved value - threshold value
As soon as the process value reaches the upper or lower limit of the threshold value band,
the value is saved. The newly saved value serves as the basis for calculating the new
threshold value band.

Integrative method
The integration threshold value calculation works with a cyclic comparison of the integrated
current value with the last stored value. The calculation cycle in which the two values are
compared is 500 milliseconds.
(Note: The calculation cycle must not be confused with the scan cycle of the CPU memory
areas).
The deviations of the current process value are totaled in each calculation cycle. The trigger
is set only when the totaled value reaches the configured value of the threshold value trigger
and a new process value is entered in the send buffer.
The method is explained based on the following example in which a threshold value of 2.0 is
configured.

CP 1243-1
102 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Table 4- 7 Example of the integration calculation of a threshold value configured with 2.0

Time [s] Process value Current process Absolute deviation Integrated devia-
(calculation cycle) stored in the value from the stored tion
send buffer value
0 20.0 20.0 0 0
0.5 20.3 +0.3 0.3
1.0 19.8 -0.2 0.1
1.5 20.2 +0.2 0.3
2.0 20.5 +0.5 0.8
2.5 20.3 +0.3 1.1
3.0 20.4 +0.4 1.5
3.5 20.5 20.5 +0.5 2.0
4.0 20.4 -0.1 -0.1
4.5 20.1 -0.4 -0.5
5.0 19.9 -0.6 -1.1
5.5 20.1 -0.4 -1.5
6.0 19.9 19.9 -0.6 -2.1

With the changes in the process value shown in the example, the threshold value trigger
configured with 2.0 fires twice:
● At the time 3.5 s: The value of the integrated deviation is at 2.0. The new process value
stored in the send buffer is 20.5.
● At the time 6.0 s: The value of the integrated deviation is at 2.1. The new process value
stored in the send buffer is 19.9.
In this example, if a deviation of the process value of approximately 0.5 should fire the
trigger, then with the behavior of the process value shown here a threshold value of
approximately 1.5 ... 2.5 would need to be configured.

4.10.10 Analog value preprocessing

CPs with data point configuration support analog value preprocessing. For analog value data
points, some or all of the functions described below can be configured.

Requirements and restrictions

You will find the requirements for the configuration of the preprocessing options and
restrictions in the section relating to the particular function.

Note
Restrictions due to configured triggers
The analog value preprocessing options "Fault suppression time", "Limit value calculation"
and "smoothing" are not performed if no threshold value trigger is configured for the relevant
data point.. In these cases, the read process value of the data point is entered in the image
memory of the CP before the preprocessing cycle of the threshold value calculation (500 ms)
elapses.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 103
Configuration
4.10 Data points

Sequence of the analog value preprocessing options

The values of analog inputs configured as an event are processed on the CPU according to
the following scheme:

Figure 4-5 Sequence of the analog value preprocessing

CP 1243-1
104 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

The 500 millisecond cycle is started by the integrative threshold value calculation. In this
cycle, the values are saved even when the following preprocessing options are enabled:
● Unipolar transfer
● Fault suppression time
● Limit value calculation
● Smoothing

Mean value generation

Note
Restricted preprocessing options if mean value generation is configured
If you configure mean value generation for an analog value event, the following
preprocessing options are not available:
• Unipolar transfer
• Fault suppression time
• Smoothing

Function
With this parameter, acquired analog values are transferred as mean values.
If mean value generation is active, it makes sense to configure a time trigger..
The current values of an analog data point are read in a 100 millisecond cycle and totaled.
The number of read values per time unit depends on the read cycle of the CPU and the CPU
scan cycle of the CP.
The mean value is calculated from the accumulated values as soon as the transfer is
triggered by a trigger. Following this, the accumulation starts again so that the next mean
value can be calculated.
The mean value can also be calculated if the transmission of the analog value message is
triggered by a request from the communications partner. The duration of the mean value
calculation period is then the time from the last transmission (for example triggered by the
trigger) to the time of the request. Once again, the accumulation restarts so that the next
mean value can be calculated.

Input modules: Overflow range / underflow range

As soon as a value is acquired in the overflow or underflow range, mean value generation is
stopped. The value 32767 / 7FFFh or -32768 / 8000h is saved as an invalid mean value for
the current mean value calculation period and sent with the next message.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 105
Configuration
4.10 Data points

The calculation of a new mean value is then started. If the analog value remains in the
overflow or underflow range, one of the two values named is again saved as an invalid mean
value and sent when the next message is triggered.

Note
Fault suppression time > 0 configured
If you have configured an error suppression time and then enable mean value generation,
the value of the error suppression time is grayed out but no longer used. If mean value
generation is enabled, the error suppression time is set to 0 (zero) internally.

Unipolar transfer

Restrictions
Unipolar transfer cannot be configured at the same time as mean value generation. Enabling
unipolar transfer has no effect when mean value generation is activated.

Function
With unipolar transfer, negative values are corrected to zero. This can be desirable if values
from the underrange should not be transferred as real measured values.
Exception: With process data from input modules, the value -32768 / 8000h for wire break of
a live zero input is transferred.
With a software input, on the other hand, all values lower than zero are corrected to zero.

Fault suppression time

Requirements for the function

Configuration of the threshold trigger for this data point

Restrictions
The fault suppression time cannot be configured at the same time as mean value generation.
A configured value has no effect when mean value generation is activated.

Function
A typical use case for this parameter is the suppression of peak current values when starting
up powerful motors that would otherwise be signaled to the control center as a disruption.
The transmission of an analog value in the overflow (7FFFh) or underflow range (8000h) is
suppressed for the specified time. The value 7FFFH or 8000H is only sent after the fault
suppression time has elapsed, if it is still pending.
If the value returns to the measuring range before the fault suppression time elapses, the
current value is transferred.

CP 1243-1
106 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Input modules
The suppression is adjusted to analog values that are acquired directly by the S7 analog
input modules as raw values. These modules return the specified values for the overflow or
underflow range for all input ranges (also for live zero inputs).
An analog value in the overflow range (32767 / 7FFFh) or underflow range (-32768 / 8000h)
is not transferred for the duration of the fault suppression time. This also applies to live zero
inputs. The value in the overflow/underflow range is only sent after the fault suppression time
has elapsed, if it is still pending.

Recommendation for finished values that were preprocessed by the CPU:

If the CPU makes preprocessed finished values available in bit memory or in a data block,
suppression is only possible or useful if these finished values also adopt the values listed
above 32767 / 7FFFh or -32768 / 8000h in the overflow or underflow range. If this is not the
case, the parameter should not be configured for preprocessed values.
For finished values preprocess in the CPU, the limits for the overflow and underflow can be
freely assigned.

Smoothing factor

Requirements for the function

Configuration of the threshold trigger for this data point

Restrictions
The smoothing factor cannot be configured at the same time as mean value generation. A
configured value has no effect when mean value generation is activated.

Function
Analog values that fluctuate quickly can be evened out using the smoothing function.
The smoothing factors are calculated according to the following formula as with S7 analog
input modules.

where
yn = smoothed value in the current cycle
xn = value acquired in the current cycle n
k = smoothing factor
The following values can be configured for the module as the smoothing factor.
● 1 = No smoothing
● 4 = Weak smoothing
● 32 = Medium smoothing
● 64 = Strong smoothing

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 107
Configuration
4.10 Data points

Set limit value 'low' / Set limit value 'high'

Requirements for the function

● Configuration of the threshold trigger for this data point
● PLC tag in the bit memory operand area or data area
The analog value data point must be linked to a PLC tag in the bit memory or data area
(data block). For PLC tags of hardware modules (input operand area) limit value
configuration is not possible.
The configuration of limit values is pointless for measured values that have already been
preprocessed on the CPU.

Function
In these two input boxes, you can set a limit value in the direction of the start of the
measuring range or in the direction of the end of the measuring range. You can also
evaluate the limit values, for example as the start or end of the measuring range.

Status identifier "OVER_RANGE" / "overflow"

With protocols that support status identifiers, if the limit value is overshot or undershot, the
status identifier of the data point is set for measured range violation known below as the
identifier "OV". This status identifiers are described in the section Status IDs of the data
points (Page 95).
The "OV" bit of the status identifier of the data point is set as follows when the relevant
analog value is transferred:
● Limit value 'high':
– If the limit value is exceeded: OV = 1
– If the value then falls below the limit value: OV = 0
● Limit value 'low':
– If the value falls below the limit value: OV = 1
– If the value then exceeds the limit value: OV = 0

Configuration of the limit value

The limit value is configured as a whole decimal number. The range of values is based on
the range of values of the raw value of analog input modules.
Entry as a decimal number according to the range of values of the assigned PLC tag from
the bit memory or data area.
The entry of the value 0 (zero) is interpreted as a deactivated limit value.

CP 1243-1
108 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Range Raw value (16 bits) of the PLC tag Module output [mA] Measuring
Decimal Hexadecimal 0 .. 20 -20 .. +20 4 .. 20 range [%]

(unipolar) (bipolar) (life zero)

Overflow 32767 7FFF > 23.515 > 23.515 > 22.810 > 117.593
Overrange 32511 7EFF 23.515 23.515 22.810 117.593
... ... ... ... ... ...
27649 6C01 20.001 20.001 20.001 100.004
Nominal range 27648 6C00 20 20 100
(unipolar / life zero) ... ... ... ... ...
0 0000 0 4 0
Nominal range (bipolar) 27648 6C00 20 100
... ... ... ...
0 0000 0 0
... ... ... ...
-27648 9400 -20 -100
Underrange -1 FFFF -0.001 3.999 -0.004
(unipolar / life zero) ... ... ... ... ...
-4864 ED00 -3.518 1.185 -17.59
Underrange (bipolar) -27649 93FF -20.001 -100.004
... ... ... ...
-32512 8100 -23.516 -117.593
Undershoot / wire break -32768 8000 < -3.518 < 1.185 < -17.593

Note
Evaluation of the value even when the option is disabled
If you enable one or both options and configure a value and then disable the option later, the
grayed out value is nevertheless evaluated.
To disable the two options, delete the previously configured values limit values from the input
boxes and then disable the relevant option.

Recommendation for quickly fluctuating analog values:

If the analog value fluctuates quickly, it may be useful to smooth the analog value first if limit
values are configured.

4.10.11 Command outputs

Parameters for command outputs

With the DNP3 and IEC protocols, the following parameters can be configured for command
outputs:
● LATCH_ON / LATCH_OFF
● PULSE_ON

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 109
Configuration
4.10 Data points

The parameters can be configured for the following data point types:
● DNP3
Binary Command Output
● IEC
Single command

Configuration
The data point types allow receipt of a command with the following control information
(control code):
● LATCH_ON / LATCH_OFF
or
● PULSE_ON
When the byte "Control Code" is received with the function "PULSE_ON" information sent
with it by the master "Count", "On-time" and "Off-time" is evaluated and compared to the
object parameters "Max. pulse duration", "Pulse duration replacement time" and "Max.
number of pulses" (see below).
The following control codes sent by the master station are evaluated.

Table 4- 8 Functions of the data object

Receipt of: Reaction of the object depends on the configuration

Control TCC * Op Type ** Output mode = Output mode =
Code Pulse on Latch on/off
0x01 NUL PULSE_ON The output is set to 1 for the The command is rejected.
duration of “On-time“.
0x03 NUL LATCH_ON The command is rejected. The output is set permanently
to 1.
0x04 NUL LATCH_OFF The command is rejected. The output is set permanently
to 0.
0x41 CLOSE PULSE_ON The output is set permanently The command is rejected.
to 1 (as with LATCH_ON).
0x81 TRIP PULSE_ON The output is set permanently The command is rejected.
to 0 (as with LATCH_OFF).

* Trip-Close Code field

** Operation Type field

Parameter

Name: Max. number of pulses

Range of val- 0 ... 255
ues:

CP 1243-1
110 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.10 Data points

Default: 0
Explanation: Monitors the number of pulses sent by the master station (Count). If the
number of pulses received from the master station exceeds the value con-
figured here, the command is rejected.
If you enter 0 (zero), the monitoring is disabled.

Name: Max. pulse duration

Range of val- 0 ... 65535
ues:
Default: 0
Explanation: Monitors the pulse duration sent by the master (On-time). If the duration of
the pulse received from the master exceeds the value configured here, the
configurable "Pulse duration replacement time" is used.
If the "Pulse duration replacement time" is configured with zero, the com-
mand is rejected.
With 0 (zero) the "Pulse duration replacement time" is used for every pulse.

Name: Pulse duration equivalent time

Range of val- 0 ... 65535
ues:
Default: 0
Explanation: Replacement value for the pulse duration If the pulse duration received from
the master exceeds the value configured in “Max pulse duration“. The pa-
rameter is only used when “Max. pulse duration“ is configured.
If the value is 0 (zero), no replacement value is used.
If the ""Max. pulse duration" and "Pulse duration replacement time" are con-
figured with zero, the command is rejected.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 111
Configuration
4.10 Data points

4.10.12 Partner stations

4.10.12.1 Partner configuration for DNP3 and IEC data points

Enabling the partners for data points - DNP3 / IEC

Enable all configured partners with which the selected data point will exchange data. You
specify the communications partners of the CP in the "Partner stations" parameter group.
● Partner 1 enabled
In the overview table of the data points, as default Partner 1 is set as the partner of a data
point.
In the "Partner stations" tab, in this case Partner 1 is enabled, the option grayed out.
● Partner n enabled
If you enable a different partner or more partners for this data point in the overview table,
these will be enabled in the "Partner stations" tab and all 4 partners can be selected or
deselected.

4.10.12.2 Partner configuration with TeleControl Basic data points.

Enabling the partner for data points - TeleControl Basic

Enable the partner with which the selected data point will exchange data.
A communications can be configured. The telecontrol server and an S7 station cannot be
selected as the partner for a data point at the same time.
The communications partner may be:
● The telecontrol server
Since the telecontrol server is always enabled as a communications partner of the CP, it
is adopted as default in this tab.
The option "Telecontrol server enabled" is selected and grayed out.
● An S7 station
The station must be reachable via the "TeleControl Basic" protocol.
You specify the communications partners of the CP in the "Partner stations" parameter
group.
Activate one of the two options.
● Telecontrol server enabled
Only the telecontrol server is a communications partner of the data point.
● Partner for inter-station communication
Only the S7 station is a communications partner of the data point.

CP 1243-1
112 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.11 Messages

Partner number (inter-station communication)

Specify the partner CP for inter-station communication for the selected data point by
selecting the required partner from the drop-down list. The access ID of the relevant partner
is shown in brackets.
The partners you specified in the "Partner stations" > "Partner for inter-station
communication" can be selected.

Data point index

Index of the corresponding data point on the communications partner.
Note:
● The data pair of the sending and receiving CP must have an identical data point index. A
receiving data point of CP 2 corresponds to a sending data point of CP 1 with the same
data point index.
● For the opposite communications direction, a second pair of data points must be created:
A sending data point of CP 2 corresponds to the receiving data point of CP 1. Once
again, both have an identical data point index.

4.11 Messages

Configuring e-mails
If important events occur, the CP can send e-mails to a communications partner.
For the requirements for using e-mails, see section E-mail configuration (Page 69).
You configure the e-mail in STEP 7 in the editor for the data point and message
configuration. You can find this using the project tree:
Project > directory of the relevant station > Local modules > CP
For the view in STEP 7, refer to the section Data point configuration (Page 82).
General functions of the message editor such as copying or column settings correspond to
those of the data point editor.

Requirements and necessary information

Remember the following requirements in the CP configuration for the transfer of e-mails:
● Configuring the "E-mail configuration" parameter group (see "Security" parameter group)
To do this, you require the following information:
– Access data of the SMTP server: Address, port number, user name, password
– CP's own e-mail address
– Email address of the recipient

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 113
Configuration
4.11 Messages

"Message parameter"
Here you configure the recipient, the subject and the text of the message.

"Trigger"
In the "Trigger" parameter group you configure triggering for sending the message and other
parameters.
● E-mail trigger
Specifies the event for which the sending of the e-mail is triggered.
– Use PLC tag
For the trigger signal to send the e-mail, the edge change (0 → 1) of the trigger bit
"PLC tag for trigger" is evaluated that is set by the user program. When necessary, a
separate trigger bit can be configured for each e-mail. For information on the trigger
bit, see below.
– CPU changes to STOP
– CPU changes to RUN
– Connection to a partner interrupted
Triggers the sending of the e-mail when the connection to a partner is interrupted.
– Connection to a partner established
Triggers the sending of the e-mail when the connection returns.
Following triggers only with TeleControl Basic:
– Connection establishment to partner failed
Triggers the sending of the e-mail when the connection to a partner could not be
established.
– Teleservice session started
– Teleservice session ended
● PLC tag for trigger
PLC tag for the e-mail trigger "Use PLC tag"
If the memory area of the trigger bit is in the bit memory or in a data block, the trigger bit
is reset to zero when the e-mail is sent.
● Enable identifier for processing status
If the option is enabled, every attempt to send returns a status with information about the
processing status of the sent message.
The status is written to the "PLC tag for processing status". If there are problems
delivering messages, you can determine the status via the Web server of the CPU by
displaying the value of the PLC tag there.
For the significance of the status output in hexadecimal, refer to the section Processing
status of e-mails (Page 126).

CP 1243-1
114 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Configuration
4.12 Access to the Web server

● PLC tag for processing status

PLC tag of the type DWORD for the processing status
● Include value
If you enable the option, the CP sends a value for the placeholder $$ from the memory
area of the CPU in the message. To do this enter "$$" as a placeholder for the value to
be sent in the message text.
Select a PLC tag whose value will be integrated in the message. The value is entered in
the message text instead of the placeholder $$.
$$ can be a placeholder for data point types with a simple data type up to a size of 32
bits.
● PLC tag for value
PLC tag in which the value to be sent is written.

4.12 Access to the Web server

Access to the Web server of the CPU

The Web server of the S7-1200 station is located in the CPU. Via the CP, you have access
to the Web server of the CPU.
From a PC you can access the Web server of the station via TCSB if the PC is connected to
the telecontrol server via LAN.
For the requirements, refer to the manual /3/ (Page 142).
You will find information on the Web server in the manual /1/ (Page 141).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 115
Configuration
4.12 Access to the Web server

CP 1243-1
116 Operating Instructions, 04/2017, C79000-G8976-C365-03
Program blocks 5
5.1 Program blocks for OUC

Using the program blocks for Open User Communication (OUC)

You can use the instructions (program blocks) listed below for direct communication between
S7 stations.
In contrast to other communication types, Open User Communication does not need to be
enabled in the configuration of the CP because corresponding program blocks need to be
created for this. You will find details on the program blocks in the information system of
STEP 7.

Note
Different program block versions
Note that in STEP 7 you cannot use different versions of a program block in a station.

Supported program blocks for OUC

The following instructions in the specified minimum version are available for programming
Open User Communication:
● TSEND_C V3.0 / TRCV_C V3.0
Compact blocks for:
– Connection establishment / termination and sending data
– Connection establishment / termination and reception of data
Use as an alternative:
● TCON V4.0 / TDISCON V2.1
Connection establishment / connection termination
● TUSEND V4.0 / TURCV V4.0
Sending and receiving data via UDP
● TSEND V4.0 / TRCV V4.0
Sending and receiving data via TCP or ISOonTCP
● TMAIL_C V4.0
Sending e-mails
To transfer encrypted e-mails with this block, the precise time of day is required on the
CP. Configure the time-of-day synchronization.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 117
Program blocks
5.1 Program blocks for OUC

For changing configuration data of the CP during runtime:

● T_CONFIG V1.0
Program-controlled configuration of the IP parameters
The program block can be found in STEP 7 in the "Instructions > Communication > Open
User Communication" window.

Connection descriptions in system data types (SDTs)

For the connection description, the blocks listed above use the parameter CONNECT (or
MAIL_ADDR_PARAM with TMAIL_C). The connection description is stored in a data block
whose structure is specified by the system data type (SDT).

Creating an SDT for the data blocks

Create the SDT required for every connection description as a data block (global DB).
You generate the SDT type by entering the name e.g. "TCON_Param" in the "Data type" box
manually in the declaration table of the block instead of selecting an entry from the "Data
type" drop-down list. The corresponding SDT is then created with its parameters.

Using the SDT

● TCON_IP_v4
For transferring frames via TCP
● TADDR_Param
For transferring frames via UDP
● TCON_IP_RFC
For transferring frames via ISO-on-TCP (direct communication between two S7-1200
stations)
● TMail_V4
For transferring e-mails addressing the e-mail server using an IPv4 address
● TMail_V6
For transferring e-mails addressing the e-mail server using an IPv6 address
● TMail_FQDN
For transferring e-mails addressing the e-mail server using its name (FQDN)
● TMail_V4_SEC
For secure transfer of e-mails addressing the e-mail server using an IPv4 address
● TMail_V6_SEC
For secure transfer of e-mails addressing the e-mail server using an IPv6 address
● TMail_QDN_SEC
For secure transfer of e-mails addressing the e-mail server using the host name
You will find the description of the SDTs with their parameters in the STEP 7 information
system under the relevant name.

CP 1243-1
118 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Program blocks
5.2 Changing the IP address during runtime

Connection establishment and termination

Connections are established using the program block TCON. Note that a separate program
block TCON must be called for each connection.
A separate connection must be established for each communications partner even if
identical blocks of data are being sent.
After a successful transfer of the data, a connection can be terminated. A connection is also
terminated by calling "TDISCON".

Note
Connection abort
If an existing connection is aborted by the communications partner or due to disturbances on
the network, the connection must also be terminated by calling TDISCON. Make sure that
you take this into account in your programming.

5.2 Changing the IP address during runtime

Changing the IP address during runtime

You can change the following address parameters of the CP at runtime controlled by the
program:
● IP address
● Subnet mask
● Router address

Note
Changing the IP parameters with a dynamic IP address
Note the effects of program-controlled changes to the IP parameters if the CP obtains a
dynamic IP address from the Internet service provider: In this case, the CP can no longer be
reached by communications partners.

Requirements - firmware version

Requirements for program-controlled changing of the IP parameters are as follows:
● CP firmware ≥ V2.1.7x
and
● CPU firmware ≥ V4.2

Requirements - program blocks / STEP 7 versions

Program-controlled changing of the IP parameters is supported by program blocks. The
program blocks access address data stored in a suitable system data type (SDT).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 119
Program blocks
5.2 Changing the IP address during runtime

Apart from the address parameters of the CP, with T_CONFIG the address parameters of
DNS servers (IF_CONF_DNS) and NTP servers (IF_CONF_NTP) can also be changed
program controlled.
Depending on the STEP 7 version, the following program blocks and system data types can
be used:
● STEP 7 Basic ≥ V14
T_CONFIG
Along with:
– IF_CONF_V4
– IF_CONF_NTP
– IF_CONF_V6
– IF_CONF_DNS
● STEP 7 Basic ≤ V14
TC_CONFIG
Along with:
– IF_CONF_V4
You will find detailed information on programming the blocks in the STEP 7 information
system.

Requirements - CP programming
To be able to change the IP parameters program controlled the option "IP address is set
directly at the device" must be enabled in the configuration of the IP address of the Ethernet
interface of the CP.

CP 1243-1
120 Operating Instructions, 04/2017, C79000-G8976-C365-03
Diagnostics and upkeep 6
6.1 Diagnostics options
The following diagnostics options are available.

LEDs of the module

For information on the LED displays, refer to the section LEDs (Page 26).

STEP 7: The "Diagnostics" tab in the Inspector window

Here, you can obtain the following information about the online status of the selected
module.

STEP 7: Diagnostics functions in the "Online > Online and diagnostics" menu
Using the online functions, you can read diagnostics information from the CP from an
engineering station on which the project with the CP is stored.
If you want to operate online diagnostics with the station via the CP, you need to activate the
online functions in the parameter group "Communication types" see the section
Communication types (Page 45).

"Diagnostics" group
Here, you can obtain the following static information on the selected module:
● General information on the module
General information on the module
● Diagnostics status
Information on the diagnostics status
● Ethernet interface
Address and statistical information

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 121
Diagnostics and upkeep
6.1 Diagnostics options

● Industrial Remote Communication

Here, you obtain specific information on the WAN interface and other parameters of the
CP. The entry has the following subentries:
– Partner
Information about the address settings of the partner, connection statistics,
configuration data of the partner and other diagnostics information.
– Data point list
Various information on the data points such as configuration data, value, connection
status etc.
– Protocol diagnostics
With the function "Enable protocol trace" the frames received and sent by the module
are copied for several seconds.
With the function "Disable protocol trace", the logging is stopped and the data is
written to a logging file.
With the function "Save", you can save the log file on the engineering station and then
analyze it.
– Device-specific events
Information on CP-internal events
● Time
Information on the time on the device

"Functions" group
● Saving service data
The function serves for logging of internal processes is situations in which you cannot
eliminate unexpected or unwanted behavior of the module yourself.
The log file is created with the "Save service data" button. The data is saved in a file with
the format "*.dmp" that can be evaluated by the Siemens hotline.

STEP 7: The partner status

The CP can signal the status of the connection to the communications partner to the CPU
via a PLC tag. You can display the status of the PLC tag via the Web server of the CPU
For information on the configuration, refer to the section Partner stations (Page 54).

Web server of the CPU

Via the CP you can access the Web server of the CPU and the information available there.
For access, refer to the section Access to the Web server (Page 115).

SNMP
For information on the functions, refer to the section SNMP (Page 125).

CP 1243-1
122 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Diagnostics and upkeep
6.2 Online security diagnostics via port 8448

6.2 Online security diagnostics via port 8448

Security diagnostics without opening port 102

If you want to perform security diagnostics without opening port 102, follow the steps below:
1. Select the CP in STEP 7.
2. Open the "Online & diagnostics" shortcut menu.
3. In the parameter group "Security" click the "Connect online" button.
In this way you perform the security diagnostics via port 8448.

See also
Settings for online security diagnostics and downloading to station with the firewall activated
(Page 68)

6.3 Online functions and TeleService

Online functions and TeleService

Along with STEP 7 on the engineering station (ES) the CP provides various diagnostics and
maintenance functions under the following terms:
● Online functions
Access from the ES to the station via LAN
Requirement: The ES and the CP are located in the same subnet.
● TeleService
Access from the ES to the station via WAN (Internet)
Requirement: The CP is connected to the telecontrol server and can be reached via this
path Refer to the information in section Access to the Web server (Page 115).
For a remote station located in a different IP subnet or that can be reached via the
Internet, these functions can only be used if the ES (with CP 1628 or via SCALANCE S)
is connected to the station via a VPN tunnel.
Connections between a CP and telecontrol server for transferring user data are not
interrupted by a TeleService-connection.
The functions and the connection establishment are largely the same with the online
functions and TeleService.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 123
Diagnostics and upkeep
6.3 Online functions and TeleService

Note
Transmission time with TeleService
Note that transferring larger amounts of data via WAN (Internet) can take a very long time.
If there are disruptions or interruptions of the transmission path this can lead to the data
transmission being aborted.

Connection establishment to use the online functions via Ethernet

Procedure:
1. Connect the ES to the network.
2. Open the relevant STEP 7 project on the ES.
3. Select the CP or the CPU of the station whose CP you want to update with new firmware.
4. Enable the online functions using the "Connect online" icon.
5. In the "Connect online" dialog, go to the Choose the entry "TeleService via telecontrol" in
the "Type of PG/PC interface" drop-down list.
6. In the "PG/PC interface" drop-down list select the entry "TeleService board".
7. In the table select the CP if it is not already selected.
The path both via the CP or the CPU is possible.
8. Click on the icon next to the "PG/PC interface" drop-down list.
The "Establish remote connection via telecontrol" dialog box opens.
9. Make the necessary entries in this dialog (see below) and click on "Connect".

Information in the "Establish remote connection via telecontrol" dialog.

In this dialog, enter the data previously configured in STEP 7 under the following headings:
● Telecontrol server / TeleService gateway...
Selection whether the TeleService switching station is located on the PC of the
engineering station or in the network or can be reached via the Internet.
A TeleService gateway cannot be used as a switching station only the telecontrol server.
– Enter the address of the telecontrol server.
IP address or name and port number of the telecontrol server that can be resolved by
DNS
– Own server password
Enter the telecontrol password to authenticate the CP with the telecontrol server
The telecontrol password for the CP is configured under "CP identification" in the
security settings, see also the section CP iIdentifcation with the TeleControl Basic
protocol (Page 64).

CP 1243-1
124 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Diagnostics and upkeep
6.4 SNMP

● Authentication ...
– Teleservice user name and password
Here, enter the data for the TeleService user that you configured in STEP 7 in the
global Security settings, see also section Configuration of the TeleService access
(Page 80).

Terminate online connection

On completion of the online session, terminate the online connection again using the
"Disconnect" button.

6.4 SNMP

SNMP (Simple Network Management Protocol)

SNMP is a protocol for management and diagnostics of networks and nodes in the network.
To transmit data, SNMP uses the connectionless UDP protocol.
The information on the properties of SNMP-compliant devices is entered in MIB files (MIB =
Management Information Base).

Range of performance of the CP as an SNMP agent

The CP supports data queries in the following SNMP versions:
● SNMPv1 (standard)
● SNMPv3 (Security)
It returns the contents of MIB objects of the standard MIB II according to RFC 1213 and the
Siemens Automation MIB.
● MIB II
The CP supports the following groups of MIB objects:
– System
– Interfaces
The "Interfaces" MIB object provides status information about the CP interfaces.
– IP
– ICMP
– TCP
– UDP
– SNMP
The following groups of the MIB II standard are not supported:
– Adress Translation (AT)
– EGP
– Transmission

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 125
Diagnostics and upkeep
6.5 Processing status of e-mails

● Siemens Automation MIB

The following exceptions / restrictions apply to the CP.
Write access is permitted only for the following MIB objects of the system group:
– sysContact
– sysLocation
– sysName
A set sysName is sent as the host name using DHCP option 12 to the DHCP server to
register with a DNS server.
For all other MIB objects / MIB object groups, only read access is possible for security
reasons.
Traps are not supported by the CP.
For more detailed information about the MIB files and SNMP, refer to the manual /5/
(Page 142).

Configuration
For information on the configuration, refer to:
● With security functions disabled (SNMPv1): SNMP (Page 53)
● With security functions enabled (SNMPv1 / SNMPv3): SNMP (Page 70)

6.5 Processing status of e-mails

Configuration of the processing status of e-mails

The following status identifiers apply to e-mails configured with the message editor of the
CP. The output of status identifiers is enabled by the option "Enable identifier for processing
status". The status identifier is written to the "PLC tag for processing status" in the CPU.
For information on the configuration, refer to the section Messages (Page 113).

Outputting the processing status of e-mails

The processing status is returned by the CP itself or the servers of the service after transfer
of a message to be sent.
If there are problems delivering messages, you can determine the status via the Web server
of the CPU.

CP 1243-1
126 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Diagnostics and upkeep
6.5 Processing status of e-mails

Processing status of e-mails

The meaning of the status identifiers of the "PLC tag for processing status" is as follows:

Table 6- 1 Meaning of the status ID output in hexadecimal format

Status Meaning
0000 Transfer completed free of errors
82xx Other error message from the e-mail server
Apart from the leading "8", the message corresponds to the three-digit error number of the
SMTP protocol.
8401 No channel available. Possible cause: There is already an e-mail connection via the CP. A
second connection cannot be set up at the same time.
8403 No TCP/IP connection could be established to the SMTP server.
8405 The SMTP server has denied the login request.
8406 An internal SSL error or a problem with the structure of the certificate was detected by the
SMTP client.
8407 Request to use SSL was denied.
8408 The client could not obtain a socket for creating a TCP/IP connection to the mail server.
8409 It is not possible to write via the connection. Possible cause: The communications partner
reset the connection or the connection aborted.
8410 It is not possible to read via the connection. Possible cause: The communications partner
terminated the connection or the connection was aborted.
8411 Sending the e-mail failed. Cause: There was not enough memory space for sending.
8412 The configured DNS server could not resolve specified domain name.
8413 Due to an internal error in the DNS subsystem, the domain name could not be resolved.
8414 An empty character string was specified as the domain name.
8415 An internal error occurred in the cURL module. Execution was aborted.
8416 An internal error occurred in the SMTP module. Execution was aborted.
8417 Requests to SMTP on a channel already being used or invalid channel ID. Execution was
aborted.
8418 Sending the e-mail was aborted. Possible cause: Execution time exceeded.
8419 The channel was interrupted and cannot be used before the connection is terminated.
8420 Certificate chain from the server could not be verified with the root certificate of the CP.
8421 Internal error occurred. Execution was stopped.
8450 Action not executed: Mailbox not available / unreachable. Try again later.
84xx Other error message from the e-mail server
Apart from the leading "8", the message corresponds to the three-digit error number of the
SMTP protocol.
8500 Syntax error: Command unknown.
This also includes the error of having a command chain that is too long. The cause may be
that the e-mail server does not support the LOGIN authentication method.
Try sending e-mails without authentication (no user name).
8501 Syntax error. Check the following configuration data:
Alarm configuration > E-mail data (Content):
• Recipient address ("To" or "Cc").

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 127
Diagnostics and upkeep
6.5 Processing status of e-mails

Status Meaning
8502 Syntax error. Check the following configuration data:
Alarm configuration > E-mail data (Content):
• Email address (sender)
8535 SMTP authentication incomplete. Check the "User name" and "Password" parameters in
the CP configuration.
8550 SMTP server cannot be reached. You have no access rights. Check the following configu-
ration data:
• CP configuration > E-mail configuration:
– User name
– Password
– Email address (sender)
• Alarm configuration > E-mail data (Content):
– Recipient address ("To" or "Cc").
8554 Transfer failed
85xx Other error message from the e-mail server
Apart from the leading "8", the message corresponds to the three-digit error number of the
SMTP protocol.

CP 1243-1
128 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Diagnostics and upkeep
6.6 Downloading firmware

6.6 Downloading firmware

New firmware versions of the CP

If a new firmware version is available for the module, you will find this on the following
Internet page of Siemens Industry Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15922/dl)
Note that firmware versions as of V3 cannot be loaded on CPs with hardware product
version 1.
When you have saved the new firmware file on your engineering station (ES), the following
methods are available to you for loading the firmware file:
● Saving the firmware file on the memory card of the CPU (recommended method)
You will find a description of the procedure in the S7-1200 system manual.
● Loading the firmware with the online functions of STEP 7 via Ethernet
You will find a description of connecting the ES to the station in the section Online
functions and TeleService (Page 123).
● Downloading the firmware via the Web server of the CPU (as of CPU firmware version
V4.0)
This method is described below.

Note
Effects on the retentive memory of the CPU
• If you use a SIMATIC memory card to install the firmware file, the retentive memory is
retained.
• If you use the Web server or the online functions to install the firmware file, retentive
memory is lost.

Downloading the firmware via the Web server of the CPU

Follow the steps below to connect to the Web server of the CPU from the ES and to
download the CP's new firmware file to the station.

Requirements in the network configuration

● The CP is connected to the telecontrol server and can be reached via this path
Refer to the information in section Access to the Web server (Page 115).

Requirements in the CPU configuration

1. Open the corresponding project on the ES.
2. Select the CPU of the station involved in STEP 7.
3. Select the "Web server" entry.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 129
Diagnostics and upkeep
6.6 Downloading firmware

4. In the parameter group "General", select the "Enable Web server for this interface"
option.
5. With a CPU version V4.0 or higher, create a user in the user administration with the
required rights.
You need to assign the right to perform firmware updates in the access level.
The procedure for establishing a connection to the Web server depends on whether you
have enabled or disabled the "Allow access only using HTTPS" option in the "General"
parameter group:
● Connection establishment with HTTP
Procedure if the "Allow access only using HTTPS" option is disabled
● Connection establishment with HTTPS
Procedure if the "Allow access only using HTTPS" option is enabled
These two variants are described in the following sections.
Requirement: The new firmware file is stored on your engineering station.
You will find the requirements for access to the Web server of the CPU (permitted Web
browser) and the description of the procedure in the STEP 7 information system under the
keyword "Information about the Web server".

Connection establishment with HTTP

1. Connect the PC on which the new firmware file is located to the CPU via the Ethernet
interface.
2. Enter the address of the CPU in the address box of your Web browser: http://<IP
address>
3. Press the Enter key.
The start page of the Web server opens.
4. Click on the "Download certificate" entry at the top right of the window.
The "Certificate" dialog opens.
5. Download the certificate to your PC by clicking the "Install certificate ..." button.
The certificate is loaded on your PC.
You will find information on downloading a certificate in the help of your Web browser and
in the STEP 7 information system under the key words "HTTPS" or "Access for HTTPS
(S7-1200)".
6. When the connection has changed to the secure mode HTTPS ("https://<IP address>/..."
in the address box of the Web server), you can continue as described in the next section
"Downloading firmware".
If you terminate the connection to the Web server, the next time you can log in with the
Web server without downloading the certificate using HTTP.

CP 1243-1
130 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Diagnostics and upkeep
6.6 Downloading firmware

Connection establishment with HTTPS

1. Connect the PC on which the new firmware file is located to the CPU via the Ethernet
interface.
2. Enter the address of the CPU in the address box of your Web browser: https://<IP
address>
3. Press the Enter key.
The start page of the Web server opens.
4. Continue as described in the following section "Downloading firmware".

Loading firmware
1. Log in on the start page of the Web server as a user with the necessary rights.
Use the user data configured in the user administration of the Web server of the CPU.
2. After logging in, select the entry "Module status" in the navigation panel of the Web
server.
3. Select the CP in the module list.
4. Select the "Firmware" tab lower down in the window.
5. Browse for the firmware file on your PC using the "Browse..." button and download the file
to the station using the "Run update" button.

Note
Closing the Web server
If you close the Web server during the firmware update, you cannot change the operating
status of the CPU to RUN. In this case you need to turn the CPU off and on again to change
the CPU to the operating status RUN.

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 131
Diagnostics and upkeep
6.7 Module replacement

6.7 Module replacement

Module replacement

CAUTION
Read the system manual "S7-1200 Programmable Controller"
Prior to installation, connecting up and commissioning, read the relevant sections in the
system manual "S7-1200 Programmable Controller" (refer to the documentation in the
Appendix).
When installing and connecting up, keep to the procedures described in the system manual
"S7-1200 Programmable Controller".
Make sure that the power supply is turned off when installing/uninstalling the devices.

The STEP -7 project data of the CP is stored on the local CPU. If there is a fault on the
device, this allows simple replacement of the CP without needing to download the project
data to the station again.
When the station starts up again, the new CP reads the project data from the CPU.

CP 1243-1
132 Operating Instructions, 04/2017, C79000-G8976-C365-03
Technical data 7
7.1 Technical specifications of the CP 1243-1

Table 7- 1 Technical specifications of the CP 1243-1

Technical specifications
Article number 6GK7 243-1BX30-0XE0
Attachment to Industrial Ethernet
Quantity 1
Design RJ-45 jack
Properties 100BASE-TX, IEEE 802.3-2005, half duplex/full duplex, autocrossover, autonego-
tiation, galvanically isolated
Transmission speed 10/100 Mbps
Permitted cable lengths (Ethernet) (Alternative combinations per length range) *
0 ... 55 m • Max. 55 m IE TP Torsion Cable with IE FC RJ45 Plug 180
• Max. 45 m IE TP Torsion Cable with IE FC RJ45 + 10 m TP Cord via
IE FC RJ45 Outlet
0 ... 85 m • Max. 85 m IE FC TP Marine/Trailing/Flexible/FRNC/Festoon/Food Cable with
IE FC RJ45 Plug 180
• Max. 75 m IE FC TP Marine/Trailing/Flexible/FRNC/Festoon/Food Cable +
10 m TP Cord via IE FC RJ45 Outlet
0 ... 100 m • Max. 100 m IE FC TP Standard Cable with IE FC RJ45 Plug 180
• Max. 90 m IE FC TP Standard Cable + 10 m TP Cord via IE FC RJ45 Outlet
Electrical data
Power supply From the S7-1200 backplane bus 5 VDC
Current consumption (typical) From the S7-1200 backplane bus 250 mA
Effective power loss (typical) From the S7-1200 backplane bus 1.25 W
Permitted ambient conditions
Ambient temperature During operation with the rack in- -20 °C to +70 °C
stalled horizontally
During operation with the rack in- -20 °C to +60 °C
stalled vertically
During storage -40 ℃ to +70 ℃
During transportation -40 ℃ to +70 ℃
Relative humidity During operation ≤ 95 % at 25 °C, no condensation
Design, dimensions and weight
Module format Compact module for S7-1200, single width
Degree of protection IP20
Weight 122 g

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 133
Technical data
7.2 Pinout of the Ethernet interface

Technical specifications
Dimensions (W x H x D) 30 x 110 x 75 mm
Installation options Standard DIN rail
Switch panel
Product functions **

* For details, refer to the IK PI catalog, cabling technology

**You will find further characteristics and performance data in the section Application and
properties (Page 11).

7.2 Pinout of the Ethernet interface

Pinout of the Ethernet interface

The table below shows the pin assignment of the Ethernet interface. The pin assignment
corresponds to the Ethernet standard 802.3-2005, 100BASE-TX version.

Table 7- 2 Pin assignment of the Ethernet interface

View of the RJ-45 jack Pin Signal name Assignment

1 TD Transmit data +
2 TD_N Transmit data -
3 RD Receive data +
4 GND Ground
5 GND Ground
6 RD_N Receive data -
7 GND Ground
8 GND Ground

CP 1243-1
134 Operating Instructions, 04/2017, C79000-G8976-C365-03
Approvals A
Approvals issued

Note
Issued approvals on the type plate of the device
The specified approvals apply only when the corresponding mark is printed on the product.
You can check which of the following approvals have been granted for your product by the
markings on the type plate.

The CP has the following approvals and meets the following standards:

EC declaration of conformity
The CP meets the requirements and safety objectives of the following EU directives and it
complies with the harmonized European standards (EN) for programmable logic controllers
which are published in the official documentation of the European Union.
● 2014/34/EU (ATEX explosion protection directive)
Directive of the European Parliament and the Council of 26 Febrary 2014 on the
approximation of the laws of the Member States concerning equipment and protective
systems intended for use in potentially explosive atmospheres, official journal of the EU
L96, 29/03/2014, pages. 309-356
● 2014/30/EU (EMC)
EMC directive of the European Parliament and of the Council of February 26, 2014 on the
approximation of the laws of the member states relating to electromagnetic compatibility.;
official journal of the EU L96, 29/03/2014, pages. 79-106
● 2011/65/EU (RoHS)
Directive of the European Parliament and of the Council of 8 June 2011 on the restriction
of the use of certain hazardous substances in electrical and electronic equipment
The EC Declaration of Conformity is available for all responsible authorities at:
Siemens Aktiengesellschaft
Division Process Industries and Drives
Process Automation
DE-76181 Karlsruhe
Germany
You will find the EC Declaration of Conformity for this product on the Internet at the following
address:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15922/cert) > "EC Declaration of
Conformity"

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 135
Approvals

IECEx
The CP meets the requirements of explosion protection according to IECEx.
IECEx classification: Ex nA IIC T4 Gc
IECEx certificate: IECEx DEK 14.0088X
The CP meets the requirements of the following standards:
● EN 60079-0
Hazardous areas - Part 0: Equipment - General requirements
● EN 60079-15
Explosive atmospheres - Part 15: Equipment protection by type of protection 'n'
You can see the current versions of the standards in the IECEx certificate that you will find
on the Internet at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15922/cert)
The conditions must be met for the safe deployment of the CP according to the section
Notices on use in hazardous areas according to IECEx / ATEX (Page 32).
You should also note the information in the document "Use of subassemblies/modules in a
Zone 2 Hazardous Area" that you will find on the Internet at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/view/78381013)

ATEX
The product meets the requirements of the EC directive:2014/34/EC "Equipment and
Protective Devices for Use in Potentially Explosive Atmospheres".
ATEX approval: II 3 G Ex nA IIC T4 Gc
Type Examination Certificate: KEMA 10ATEX0166 X
Relevant standards:
● EN 60079-0:2006: Potentially explosive atmosphere - general requirements
● EN 60079-15:2005: Electrical apparatus for explosive gas atmospheres; type of
protection 'n'
The device is suitable for use in environments with pollution degree 2.
The device is suitable for use only in environments that meet the following conditions:
● Class I, Division 2, Group A, B, C, D and areas where there is no risk of explosion
● Class I, Zone 2, Group IIC and areas where there is no risk of explosion

WARNING
Installation guidelines
The product meets the requirements if you keep to the following during installation and
operation:
• The notes in the section Important notes on using the device (Page 31)
• The installation instructions in the document /1/ (Page 141)

CP 1243-1
136 Operating Instructions, 04/2017, C79000-G8976-C365-03
 Approvals

Note the conditions for the safe deployment of the CP according to the section Link:
(https://support.industry.siemens.com/cs/ww/en/ps/15922/cert).
You should also note the information in the document "Use of subassemblies/modules in a
Zone 2 Hazardous Area" that you will find on the Internet at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/view/78381013)

c(UL)us
Applied standards:
● Underwriters Laboratories, Inc.: UL 61010-1 (Safety Requirements for Electrical
Equipment for Measurement, Control, and Laboratory Use - Part 1: General
Requirements)
● IEC/UL 61010-2-201 (Safety requirements for electrical equipment for measurement,
control and laboratory use. Particular requirements for control equipment)
● Canadian Standards Association: CSA C22.2 No. 142 (Process Control Equipment)
File Number: E223122

cULus Hazardous (Classified) Locations

Underwriters Laboratories, Inc.: cULus IND. CONT. EQ. FOR HAZ. LOC.
Applied standards:
● ANSI ISA 12.12.01
● CSA C22.2 No. 213-M1987
APPROVED for Use in:
● Cl. 1, Div. 2, GP. A, B, C, D T4A; Ta = -20 °C...60 °C
● Cl. 1, Zone 2, GP. IIC T4; Ta = -20 °C...60 °C
Report / UL file: E223122 (NRAG.E223122)
Note the conditions for the safe deployment of the CP according to the section Notices
regarding use in hazardous areas according to UL HazLoc (Page 33).

FM
Factory Mutual Approval Standard Class Number 3600, 3611, 3810, ANSI/ISA-61010-1
Equipment rating:
Class I, Division 2, Group A, B, C, D, Temperature Class T4A, Ta = 60 °C
Class I, Zone 2, Group IIC, Temperature Class T4, Ta = 60 °C
Report Number: 3049779, 3049925
Note the conditions for the safe deployment of the CP according to the section Notices on
use in hazardous areas according to FM (Page 33).

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 137
Approvals

Australia - RCM
The CP meets the requirements of the AS/NZS 2064 standards (Class A).

EAC (Eurasian Conformity)

Customs union of Russia, Belarus and Kazakhstan
Declaration of the conformity according to the technical regulations of the customs union
(TR CU)

Current approvals
SIMATIC NET products are regularly submitted to the relevant authorities and approval
centers for approvals relating to specific markets and applications.
If you require a list of the current approvals for individual devices, consult your Siemens
contact or check the Internet pages of Siemens Industry Online Support:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15922/cert)

CP 1243-1
138 Operating Instructions, 04/2017, C79000-G8976-C365-03
Dimension drawings B
Note
All dimensions in the drawings of the CP are in millimeters.

Figure B-1 Front view and side view left

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 139
Dimension drawings

Figure B-2 From above

CP 1243-1
140 Operating Instructions, 04/2017, C79000-G8976-C365-03
Documentation references C
Where to find Siemens documentation
● Article numbers
You will find the article numbers for the Siemens products of relevance here in the
following catalogs:
– SIMATIC NET - Industrial Communication / Industrial Identification, catalog IK PI
– SIMATIC - Products for Totally Integrated Automation and Micro Automation, catalog
ST 70
You can request the catalogs and additional information from your Siemens
representative. You will also find the product information in the Siemens Industry Mall at
the following address:
Link: (https://mall.industry.siemens.com)
● Manuals on the Internet
You will find SIMATIC NET manuals on the Internet pages of Siemens Industry Online
Support:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15247/man)
Go to the required product in the product tree and make the following settings:
Entry type “Manuals”
● Manuals on the data medium
You will find manuals of SIMATIC NET products on the data medium that ships with many
of the SIMATIC NET products.

/1/
SIMATIC
S7-1200 Programmable Controller
System Manual
Siemens AG
Current release at the following address:
Link: (https://support.industry.siemens.com/cs/ww/en/ps/13683/man)

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 141
Documentation references

/2/
SIMATIC NET
CP 1243-1
Operating Instructions
Siemens AG
Link: (https://support.industry.siemens.com/cs/ww/en/view/103948898)

/3/
SIMATIC NET
TeleControl Server Basic (Version V3)
Operating Instructions
Siemens AG
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15918/man)

/4/
SIMATIC NET
Industrial Ethernet Security
Security basics and applications
Configuration manual
Siemens AG
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15326/man)

/5/
SIMATIC NET
Diagnostics and configuration with SNMP
Diagnostics manual
Siemens AG
Link: (https://support.industry.siemens.com/cs/ww/en/ps/15392/man)

CP 1243-1
142 Operating Instructions, 04/2017, C79000-G8976-C365-03
Index

A G
Abbreviations/acronyms, 4 Gateway, 79
Article number, 3 Glossary, 6

C H
Conditional spontaneous, 100, 101 Hardware product version, 3
Connection resources, 15
CPU firmware, 23
Cross references (PDF), 5 I
IEC addressing, 41
Image memory, 98
D
Importing a certificate - e-mail, 70
Data buffering, 16 Instructions (OUC), 117
Data point configuration, 82 Internet connections, 42
Data point type, 89 Inter-station communication, 94
Dimensions, 35 IP address - program-controlled change, 119
Disposal, 6 IP address (master), 41
DNP3 addressing, 41 IP configuration
DNP3 implementation level, 65 IPv4, IPv6, 12
DNP3 master, addressing via the Internet, 21 IP_CONF_V4, 119
DNS server, 42
DNS server - program-controlled change, 119
L
Logging server, 73
E
E-mail
Configuration, 113 M
Programming (OUC), 117
MAC address, 3
Quantity, 16
MIB, 125
Encryption, 11
Mirroring, 92
Ethernet interface
Assignment, 134
Events, 98
N
NTP, 43
F NTP (secure), 43
NTP server - program-controlled change, 119
Firewall, 14
IPsec tunnel,
Firmware version, 3
Forced image mode, 98
Frame memory, 16, 98
O
Online diagnostics, 46, 121
Online functions, 13, 121

CP 1243-1
Operating Instructions, 04/2017, C79000-G8976-C365-03 143
Index

OPC quality code, 95 Time-of-day synchronization, 12

Operating statuses (LED displays), 28 Training, 6
OUC (Open User Communication), 117 Transmission mode, 100, 101
OUC connections Trigger tag - resetting, 100
Resources, 16

U
P Unsolicited, 100, 101
Passive VPN connection establishment, 79
PG/OP connections, 16
Port 8448, 123 V
Process image, 98
Virtual IP address, 57
Product name, 4
VPN, 16, 42, 74
PUT/GET, 16

W
R
Web server, 115
Recycling, 6
Redundant DNP3 master, addressing, 22
Replacing a module, 132
Reset trigger bit, 99

S
S7 connections
Enable, 46
Resources, 16
Safety notices, 31
Security, 13
Security diagnostics without port 102, 123
Send buffer, 16, 98
Service & Support, 6
SIMATIC NET glossary, 6
SMS
Programming (OUC), 117
SMTPS, 69
SNMP, 13, 53, 125
SNMPv3, 15, 70
SSL/TLS, 69
STARTTLS, 69
Static values, 98
STEP 7 - version, 23
SYSLOG, 80

T
T_CONFIG, 119
TC_CONFIG, 119
TeleService, 13
Time stamp, 90

CP 1243-1
144 Operating Instructions, 04/2017, C79000-G8976-C365-03