User Manual

3DM2283
3-Phase Digital Stepper Drive

©2019 China Leadshine Technology Co., Ltd.

Address: 15-20/F, Block B, Nanshan I Valley, No.3185, Shahe West Road, Nanshan District, Shenzhen,

Guangdong, 518055, China

Tel: (86)755-26409254 Fax: (86)755-26402718

Web: www.leadshine.com Sales: [email protected]

Support: [email protected]
 High Voltage Digital Stepper Drive 3DM2283 Manual

3DM2283 3-phase Digital Stepper Drive

150-220VAC, 0.5-8.2A peak, Auto-configuration, Low Noise

 Anti-Resonance provides optimal torque and nulls mid-range instability
 Motor auto-identification and parameter auto-configuration technology, offers optimal
responses with different motors
 Multi-Stepping allows a low resolution step input to produce a higher microstep output, thus
offers smoother motor movement
 Microstep resolutions from full-step to51,200.
 Soft-start with no “jump” when powered on
 Supply voltage up to +220 VAC
 Output current programmable, from 0.5A to 11.7A. It can also be set via DIP switches.
 Pulse input frequency up to 200 KHz
 5V optically isolated input
 Automatic idle-current reduction (Reduction rate can be software configured)
 Suitable for 3-phase motors
 Support PUL/DIR and CW/CCW modes
 Over-voltage, over-current protections

Descriptions
The 3DM2283 is a high voltage, fully digital stepper drive developed with advanced DSP control algorithm based on the latest motion
control technology. It has achieved a unique level of system smoothness, providing optimal torque and nulls mid-range instability. Its
motor auto-identification and parameter auto-configuration feature offers quick setup to optimal modes with different motors. Compared
with traditional analog drives, 3DM2283 can drive a stepper motor at much lower noise, lower heating, and smoother movement. Its
unique features make 3DM2283 an ideal choice for high requirement applications.

Applications
Suitable for a wide range of stepper motors, from NEMA size 34 to 51. It can be used in various applications such as laser cutters, laser
markers, high precision X-Y tables, labeling machines, CNC router, etc. Its unique features make the 3DM2283 an ideal choice for
applications that require both low-speed smoothness and high speed performances

Page 2 of 7
 High Voltage Digital Stepper Drive 3DM2283 Manual

Specifications
Electrical Specifications

Parameter Min Typical Max Unit

Input Voltage 150 220 240 VAC
Pulse Input Frequency 0 - 200 kHz
Logic Signal Current 7 10 16 mA
Isolation Resistance 500 - - MΩ

Operating Environment

Cooling Natural Cooling or Forced cooling

Avoid dust, oil fog and corrosive
Environment gases
Storage Temperature -20℃ － 65℃ (-4℉ － 149℉)

Operating Environment Ambient Temperature 0℃ － 50℃ (32℉ － 122℉)

Humidity 40%RH － 90%RH
Operating Temperature (Heat
70℃ (158℉) Max
Sink)
Storage Temperature -20℃ － 65℃ (-4℉ － 149℉)
Weight 1.3Kg (2.87lbs)

Mechanical Specifications

Page 3 of 7
 High Voltage Digital Stepper Drive 3DM2283 Manual

Protection Indications
The green indicator turns on at power-up. When drive protection is activated, the red LED blinks periodicity to indicate the error type

Priority Time(s) of Blink Sequence wave of RED LED Description

3S

0.2S

1st 1 Over-current Protection

3S

0.2S 0.3S

2nd 2 Over-voltage Protection，over 440VDC

Pin Assignment
The 3DM2283 has one barrier strip connector for power and motor connections and one screw terminal for control signal connections.

Power and Motor Connector

Pin Name I/O Description
1 PE - Recommend connect this port to the ground for better safety.
2 L I Power supply inputs. If AC input, recommend use isolation transformers with
3 N I theoretical output voltage of 150-220VAC.
4 NC - No Connection
5 U O Motor Phase U
6 V O Motor Phase V
7 W O Motor Phase W

Pin Assignment (Continued)

Control Signal Connector
Pin Name I/O Description
Pulse Signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each
1 PUL+ I rising or falling edge active (software configurable, see DM drives software operational
manual for the detail); In double pulse mode (software configurable), this input represents
clockwise (CW) pulse, active both at high level and low level. 4-5V when PUL-HIGH,
0-0.5V when PUL-LOW. For reliable response, pulse width should be longer than 2.5μs.
2 PUL- I
Series connect resistors for current-limiting when +12V or +24V used. The same as DIR
and ENA signal.

Direction Signal: In single-pulse mode, this signal has low/high voltage levels, representing
3 DIR+ I two directions of motor rotation. In double-pulse mode (software configurable), this signal
is counter-clock (CCW) pulse, active both at high level and low level. For reliable motion

Page 4 of 7
 High Voltage Digital Stepper Drive 3DM2283 Manual

response, DIR signal should be ahead of PUL signal by 5μs at least. 4-5V when DIR-HIGH,
0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-driver
4 DIR- I
wiring match. Exchanging the connection of two wires for a coil to the driver will reverse
motion direction. The direction signal’s polarity is software configurable.
Enable signal: This signal is used for enabling/disabling the drive. In default, high level
5 ENA+ I
(NPN control signal) for enabling the driver and low level for disabling the driver. Usually
left UNCONNECTED (ENABLED). Please note that PNP and Differential control signals
6 ENA- I are on the contrary, namely Low level for enabling. The active level of ENA signal is
software configurable.
Fault Signal: OC output signal, active when one of the following protection is activated:
7 FAULT+ O
over-voltage, over current, low voltage, phase error and over-temperature. This port can
sink or source 20mA current at 24V. In default, the resistance between FAULT+ and
8 FAULT- O FAULT- is high impedance in normal operation and become low when 3DM2283 goes into
error.

RS232 Communication Port

The RS232 communication port is used to configure the 3DM2283’s peak current, microstep, active level, current loop parameters and
anti-resonance parameters. See DM driver’s software operational manual for more information.

RS232 Communication Port

Pin Name I/O Description
1 NC - Not connected.
2 +5V O Not connected.
3 TxD O RS232 transmit.
4 GND GND Ground.
5 RxD I RS232 receive.
6 NC - Not connected.

DIP Switch Settings

Dynamic Current

Peak RMS SW1 SW2 SW3

Default Default OFF OFF OFF
3.1A 2.2A ON OFF OFF
4.5A 3.2A OFF ON OFF
5.9A 4.2A ON ON OFF
7.3A 5.2A OFF OFF ON
8.9A 6.3A ON OFF ON
10.1A 7.2A OFF ON ON
11.7A 8.3A ON ON ON

Page 5 of 7
 High Voltage Digital Stepper Drive 3DM2283 Manual

Note: Due to motor inductance, the actual current in the coil may be smaller than the dynamic current setting, particularly under high speed condition.

Idle-Current

SW4 determines whether current-reduction is performed when there is no pulse applied to 3DM2283..

OFF ON
Motor current reduces automatically when Motor current is the same as the dynamic
SW4 there is no pulse applied to 3DM2283. current when there is no pulse applied to
3DM2283.

Microstep Resolution

Steps/Revolution SW5 SW6 SW7 SW8

200 ON ON ON ON
400 OFF ON ON ON
1600 ON OFF ON ON
3200 OFF OFF ON ON
6400 ON ON OFF ON
12800 OFF ON OFF ON
25600 ON OFF OFF ON
500 OFF OFF OFF ON
1000 ON ON ON OFF
1200 OFF ON ON OFF
2000 ON OFF ON OFF
4000 OFF OFF ON OFF
5000 ON ON OFF OFF
6000 OFF ON OFF OFF
8000 ON OFF OFF OFF
10000 OFF OFF OFF OFF

Auto-Configuration

Switch SW4 two times in two seconds will activate parameter Auto-configuration for 3DM2283’s current loop. That is, OFF-ON-OFF or
ON-OFF-ON. During Auto-configuration, motor parameters are identified and 3DM2283’s current loop parameters are calculated
automatically. The motor shaft will vibrate a little during the process of Auto-configuration which takes about 1 to 3 seconds.

Page 6 of 7
 High Voltage Digital Stepper Drive 3DM2283 Manual

Typical Connections
NPN Control Signal

R=0 if VCC=5V;
R=1K(Power>0.125W) if VCC=12V;
R=2K(Power>0.125W) if VCC=24V;
Controller R must be connected to control signal terminal. 3DM2283 Drive
PUL+ 270O
VCC
R PUL-
PUL
DIR+ 270O

R DIR-
DIR 270O
ENA+
R ENA-
ENABLE

FAULT+
FAULT
FAULT-

L
150 ~ 220 VAC N
~ AC Input

PE
U
YEL WHT
V

W
863SXX BRN M
BLU
BLK
RED

Page 7 of 7