Scribd
Upload
40 views20 pages

RCC DESIGN TEMPLATE

The document provides detailed calculations for the design of a reinforced concrete slab and columns, including live and dead loads, reinforcement requirements, and deflection checks. It specifies design moments, required and provided areas of steel, and checks for shear resistance and deflection. Additionally, it includes parameters for axial load and bending in columns, ensuring compliance with relevant design standards.

Uploaded by

lau
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
40 views20 pages

RCC DESIGN TEMPLATE

The document provides detailed calculations for the design of a reinforced concrete slab and columns, including live and dead loads, reinforcement requirements, and deflection checks. It specifies design moments, required and provided areas of steel, and checks for shear resistance and deflection. Additionally, it includes parameters for axial load and bending in columns, ensuring compliance with relevant design standards.

Uploaded by

lau
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 20

Live load (gk) (KN/m2) 6.

67 Coeffecients
Negative moment at
Dead load (qk) (KN/m2) 4.80 4.80 continous edge
Positive moment
fcu 25.00 at mid span
fy 500.00
Design load (n) 17.40
Lx (m) 3.23
Ly (m) 4.64
Thickness, h (mm) 200.00
bar diameter 10.00
cover (mm) 20.00

REINFORCEMENT FOR THE MIDDLE STRIP OF SPAN Lx

Position 1 (edge continuous) Limits


Design moment (msx) (KNm/m width) 14.70
K 0.02 0.156
Z test (mm) 171.18 0.98 0.95
Z yenyewe (mm) 166.25
Asreq (mm2/m) 186.15
As min (mm2) - .13% for fy=460 260.00
As prov (mm2) 262.00 spacing 300

Position 2 (mid-span)
Design moment (msx) (KNm/m width) 10.89
K 0.014
Z test (mm) 172.19 0.98 0.95
Z yenyewe (mm) 166.25
Asreq (mm2/m) 137.89
As min (mm2) - .13% for fy=460 260.00
As prov (mm2) 262.00 spacing 300

Position 3 (discontinuos edge)


At least 50% of bottom steel should
be provided in the top at the
support and not less than the
minimum area required. As,req (mm2) 260.00
spacing 300

Minimum area of rebar (Table 3.25 0.13%

DEFLECTION CHECK
Same as for beams in clause 3.4.6.3 using values for shorter span

(span/effective depth) <= Table 3.9 value X Table 3.10 value

Value from table 3.9 26.00


M/(bd^2) = K x fcu 0.36
Service stress fy, N/mm2 175.43
2.55
Modification factor
2.00
Deflection Test PASSED
effective depth

-0.081 d_outer (mm) 175

0.06 d_inner (mm) 165


REINFORCEMENT FOR THE MIDDLE STRIP OF SPAN Ly

Position 1 (edge continuous)


Design moment (msx) (KNm/m width) 30.34
K 0.045 0.156
Z test (mm) 156.38 0.95 0.95
Z yenyewe (mm) 156.38
Asreq (mm2/m) 408.39
As min (mm2) - .13% for fy=460 260.00
As prov (mm2) 393.00 spacing 200

Position 2 (mid-span)
Design moment (msx) (KNm/m width) 22.47
K 0.033 0.156
Z test (mm) 158.71 0.96 0.95
Z yenyewe (mm) 156.75
Asreq (mm2/m) 301.80
As min (mm2) - .13% for fy=460 260.00
As prov (mm2) 393.00 spacing 200

Position 3 (discontinuos edge)


At least 50% of bottom steel should
be provided in the top at the
support and not less than the
minimum area required. As,req (mm2) 393.00
spacing 300
Dead load, gk (KN/mm2)
Live load, qk )KN/mm2)
fcu 25
fy 500
Slab thickness, hf (mm) 200
Rib width (beam width,b) (mm) 300
Overall depth, d (mm) 300
Span of main beams, L (m) 4.64
cover (mm) 25
Bar diameter main steel (mm) 25
Bar diameter for stirrups (mm) 8

DESIGN LOADS
Load analysis
M (KNm) 62
V (KN) 80.04

Effective flange width, be


Actual flange width (mm) 3230
be, T beam (mm) 1228

Effective depth, d (mm) 254.5

BENDING
K 0.03118 0.156
Z test 245.3543 0.964064 0.95
Z yenyewe 241.775
As, req (mm2) 539.867
As prov (mm2) 603 3 bars
Minimum spacing of rebars clause 3.12.11.1

SHEAR RESISTANCE
Shear stress, v (N/mm2) 1.04833
4
Maximum shear (N/mm2) 4
5

100As/(bvd) 0.789784
Vc (N/mm2) - from table 3.8 0.6541
Sv 202
Sv 199

Deflection check
Check in with the TWO-WAY RESTRAINED SLAB SECTION
Effective
Length
width, b (mm) 300
lex (mm) 4000 3000
depth, h (mm) 350
ley (mm) 4000 3000
fcu (N/mm2) 30
fy (N/mm2) 460
cover (mm) 25
Main bar size 25
Links bar size 8
M (uniaxial) (KNm) 46.3
Mx (biaxial) (KNm)
My (biaxial) (KNm)
Axial load acting, P (KN) 1621.2
CLASSIFICATION SHORT
Factor (Table 3.27) 0.75

1. DESIGN OF AXIALLY LOADED COLUMN


Thia assumes no
eccentricity at all

This takes into


account the
eccentricity
Asc 1046.95652173913

2. COLUMNS RESISTING AXIAL LOAD AND BENDING

a) Uniaxual bending
Longitudinal steel
N/bh (N/mm2) 15.4
M/bh2 1.3
d' 304.5
d'/h 0.87

Links
Largest longitudinal bar (mm) 25
Smallest longitudinal bar (mm) 20
Smallest cross section dimension 300
diameter of links (mm) 8
Spacing of liks (mm) 240

b) Biaxial bending
Longitudinal steel
b' (mm) 254.5
h' 304.5
Mx/My #DIV/0!
h'/b' 1.19646365422397
N/bhfu 0.51
B from table #DIV/0!
Mx' #DIV/0!
Mx'/bh2 #DIV/0!
N/bh 15.4
d/h 0.87

The interpolater
THE POINT 1 2
Y #DIV/0!
X
slope (m) #DIV/0!
4.8

You might also like