Scribd
Upload
0 views

Connecting Two LANs Using Cisco Packet Tracer

The document outlines the procedure for connecting two LANs using Cisco Packet Tracer, detailing the necessary devices, IP addressing, and configuration steps. It includes instructions for setting up PCs, routers, and verifying the network connection using the ping command. The implementation section provides examples of successful pings between devices on the two LANs.

Uploaded by

shubham060505
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0 views

Connecting Two LANs Using Cisco Packet Tracer

The document outlines the procedure for connecting two LANs using Cisco Packet Tracer, detailing the necessary devices, IP addressing, and configuration steps. It includes instructions for setting up PCs, routers, and verifying the network connection using the ping command. The implementation section provides examples of successful pings between devices on the two LANs.

Uploaded by

shubham060505
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

Aim: Connecting two LANs using Cisco packet tracer.

Software: Cisco packet tracer.

Theory:
Below are the steps to configure and verify the connection between two LANs in the Cisco
packet tracer.

Procedure:
Step 1: First, open the cisco packet tracer desktop and select the devices given below:

S.NO Device Model Name Qty.

1. PC PC 8

2. Switch 2960-24TT 5

3. Router 2911 1

IP Addressing Table for PCs of LAN1 and LAN2:

LAN1:

S.No. Device IPv4 Address Subnet Mask Default gateway

1. PC0 13.12.11.1 255.255.255.0 13.12.11.5

2. PC1 13.12.11.2 255.255.255.0 13.12.11.5

3. PC2 13.12.11.3 255.255.255.0 13.12.11.5

4. PC3 13.12.11.4 255.255.255.0 13.12.11.5

LAN2:

S.No. Device IPv4 Address Subnet Mask Default gateway

1. PC4 192.168.1.1 255.255.255.0 192.168.1.5


2. PC5 192.168.1.2 255.255.255.0 192.168.1.5

3. PC6 192.168.1.3 255.255.255.0 192.168.1.5

4. PC7 192.168.1.4 255.255.255.0 192.168.1.5

●​ Then, create two network topologies (Star and Bus)as shown below the image.

●​ Use an Automatic connecting cable to connect the devices with others.

Representation of the topologies should look like the image given below:

Step 2: Configure the PCs (hosts) with IPv4 address, Subnet Mask, and Default gateway
according to the IP addressing table above.

●​ To assign an IP address in PC0, click on PC0.

●​ Then, go to desktop and IP configuration and there you will find IPv4 configuration.

●​ Fill IPv4 address, subnet mask, and default gateway to the particular input box.

●​ Repeat the same procedure with PCs of LAN2 to configure them.


Step 3. Assigning IP address using the ipconfig command.

●​ We can also assign an IP address with the help of a command.

●​ Go to the command terminal of the PC0.

●​ Then, type ipconfig <IPv4 address><subnet mask><default gateway>(if needed)

example: ipconfig 13.12.11.1 255.255.255.0 13.12.11.5


●​ Repeat the same procedure with other PCs of Both LANs to configure them thoroughly.

Step 4: Configure router with IP address and subnet mask.

IP Addressing Table Router:

Device Interface IPv4 Address Subnet Mask

FastEtherner0/0 13.12.11.5 255.255.255.0


router0
FastEtherner0/1 192.168.1.5 255.255.255.0

●​ To assign an IP address in router0, click on router0.

●​ Then, go to config and then Interfaces.

●​ Then, configure the IP address in FastEthernet and serial ports according to IP addressing
Table.

●​ Fill IPv4 address and subnet mask.


Step 5: Verifying the network by pinging the IP address of any PC. We will use the ping
command to do so.

●​ First, click on PC0 then Go to the command prompt

●​ Then type ping <IP address of targeted node>

●​ As we can see in the below image we are getting replies which means the connection is
working properly.

Example : ping 192.168.1.2


●​ A simulation of the experiment is given below we are sending PDU from PC0 to PC4.

Implementation:
Pinging from 172.16.1.1 to 192.168.1.1

Pinging from 192.168.1.1 to 172.16.1.1

Simulation From one device to another:

You might also like