Product Features

Product Features

• Max. sample rate: 625 MSa/s

• Max. output frequency: 50 MHz
• 16-bit vertical resolution
• Arbitrary waveform editing function with a max. Arb waveform length of 2 Mpts/CH (8 Mpts/CH
optional)
• Built-in high-order harmonic generator (max. 20th order)
• Independent signal frequency measurement channel with a max. frequency of 500 MHz
• USB and LAN interfaces for remote connection
• Type-C power interface for powering the instrument with mobile power source, satisfying
testing requirements in the field
• Standard Web Control function for easier remote cooperation

DG800 Pro series Function/Arbitrary Waveform Generator provides up to 625 MSa/s sample rate
and 2 Mpts/CH memory depth (standard). It is a cost-effective function/arbitrary waveform
generator that combines multiple functions including Function Generator, Arbitrary Waveform
Generator, Noise Generator, Pulse Generator, Harmonic Generator, Analog/Digital Modulator and
Counter.

Page 1
Specifications
Specifications are valid under the following conditions:

The instrument is within the calibration period and has been running ceaselessly for over 20 minutes
under the specified operating temperature (23℃ ± 5℃).

All specifications are guaranteed except the parameters marked with "Typical".

Technical Specifications
Technical Specifications

Model DG821 Pro DG822 Pro DG852 Pro

Max. Frequency 25 MHz 25 MHz 50 MHz

No. of Channels 1 2 2

Sample Rate 625 MSa/s

Vertical Resolution 16 bits

Waveform Memory
2 Mpts/CH (standard), 8 Mpts/CH (optional)
Depth

Waveform Output
Waveform Output

Output Mode Continuous, Modulation, Sweep, Burst, Sequence

Standard Waveform Sine, Square, Ramp, Pulse, Noise, Arb, Harmonic

Built-in Arb 148 types of waveforms, including Sinc, Exponential Rise, Exponential Fall,
Waveform ECG, Gaussian, HaverSine, and Lorentz.

Frequency Characteristics
Frequency Characteristics
DG821 Pro DG822 Pro DG852 Pro

Sine 1 μHz to 25 MHz 1 μHz to 25 MHz 1 μHz to 50 MHz

Square 1 μHz to 20 MHz 1 μHz to 20 MHz 1 μHz to 40 MHz

Ramp 1 μHz to 1 MHz

Pulse 1 μHz to 10 MHz 1 μHz to 10 MHz 1 μHz to 25 MHz

Page 2
Frequency Characteristics
DG821 Pro DG822 Pro DG852 Pro

Arb 1 μHz to 10 MHz 1 μHz to 10 MHz 1 μHz to 15 MHz

Harmonic 1 mHz to 10 MHz 1 mHz to 10 MHz 1 mHz to 25 MHz

Sequence 1 μSa/s to 312.5 MSa/s

Noise (-3 dB) Typical (0 dBm), >250 MHz bandwidth

Output Frequency
1 μHz or 12 digits
Resolution

±10-6 of the setting (except Arb and sequence), 0℃ to 40℃

Accuracy
±10-6 of the setting ± 1 μHz (Arb and sequence), 0℃ to 40℃

Output Characteristics
Output Characteristics

Amplitude Range
1 mVpp to 10 Vpp
(into 50 Ω)

Amplitude Range
2 mVpp to 20 Vpp
(into HighZ)

Amplitude ±(1% of setting + 2 mVpp) (into 50 Ω)

Accuracy[1] ±(1% of setting + 5 mVpp) (into HighZ)

Amplitude
0.1 mVpp, 0.1 mVrms, 1 mV, 0.1 dBm or 4 digits (whichever is lower)
Resolution

Amplitude Unit[2] Vpp, Vrms, dBm, V

±5 Vpk (ac + dc) (into 50 Ω)

Offset Range
±10 Vpk (ac + dc) (into HighZ)

±(1% of |setting| + 2 mV + 0.5% of amplitude (Vpp)) (into 50 Ω)

Offset Accuracy
±(1% of |setting| + 5 mV + 1% of amplitude (Vpp)) (into HighZ)

Offset Resolution 1 mV or 4 digits

Output Impedance Typical (0 dBm, 0 Vdc), 50 Ω ± 1%

Protection Waveform outputs are automatically disabled when overloaded

Page 3
Signal Characteristics
Signal Characteristics

Typical (0 dBm)

Harmonic Distortion 10 Hz to <10 MHz: <-60 dBc

≥10 MHz: <-50 dBc

Total Harmonic Typical (1 Vpp)

Distortion (THD) 10 Hz to 20 kHz: <0.1%

Typical (1 Vpp)
Spurious (non-
10 Hz to <10 MHz: <-65 dBc
harmonic)
≥10 MHz: <-60 dBc

Sine (50 Ω) Typical (1 Vpp, 10 kHz)

Phase Noise
20 MHz: <-110 dBc/Hz

Residual Clock Noise Typical (0 dBm), -60 dBm

Typical (1 Vpp, 0 V)
Interchannel Crosstalk
<-75 dBc

Typical (relative to 1 kHz Sine, 0 dBm)

Amplitude Flatness <10 MHz: ±0.1 dB

≥10 MHz: ±0.2 dB

Phase -360° to +360°, 0.01° resolution

Rise/Fall Time Typical (≤2 Vpp amplitude, 50 Ω load), ≤3 ns

Overshoot Typical (0 dBm amplitude, >1 kHz frequency), <5%

Square
Jitter (rms) Typical (0 dBm amplitude, >1 kHz frequency), 200 ps

Phase -360° to +360°, 0.01° resolution

Typical (1 kHz frequency, 1 Vpp amplitude, 100%

Linearity symmetry)

≤0.1% of peak output (10% to 90% amplitude)

Ramp
Symmetry 0% to 100%

Phase -360° to +360°, 0.01° resolution

Page 4
Signal Characteristics

Pulse Width 9 ns to (pulse period - 9 ns)

Pulse Width Resolution 100 ps or 5 digits

Duty Cycle 0.01% to 99.99%

Rise/Fall Time 3 ns to 0.625*pulse period

Pulse
0 ps to period – [pulse width + 0.8*(Leading Edge
Delay Time
Time + Trailing Edge Time)] (Continuous mode)

Overshoot Typical (0 dBm amplitude, >1 kHz frequency), <5%

Jitter (rms) Typical (0 dBm amplitude, >1 kHz frequency), 200 ps

Phase -360° to +360°, 0.01° resolution

Noise Type White noise

Rise/Fall Time Typical (<1 Vpp amplitude), ≤5 ns

Arb Jitter (rms) Typical (0 dBm amplitude, >1 kHz frequency), 200 ps

Phase -360° to +360°, 0.01° resolution

Harmonic Order ≤20

Harmonic Type Order, Combine

Harmonic Output
The amplitude of each order of the harmonic can be
Harmonic Amplitude
set.

Harmonic Phase The phase of each order of the harmonic can be set.

Modulation Characteristics
Modulation Characteristics

Modulation Type AM, FM, PM, ASK, FSK, PSK, PWM, SUM

Page 5
Modulation Characteristics

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

Modulation Source Internal/External

Internal Modulating Sine, Square, Triangle, UpRamp, DnRamp, Noise,

AM Waveform Arb

Modulation Depth 0% to 120%

Internal Modulation
1 mHz to 1 MHz
Frequency

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

Modulation Source Internal/External

FM Internal Modulating Sine, Square, Triangle, UpRamp, DnRamp, Noise,

Waveform Arb

Internal Modulation
1 mHz to 1 MHz
Frequency

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

Internal Modulation
Internal/External
Source

Internal Modulating Sine, Square, Triangle, UpRamp, DnRamp, Noise,

PM
Waveform Arb

Internal Modulation
1 mHz to 1 MHz
Frequency

Phase Deviation 0° to 360°, 0.01° resolution

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

Modulation Source Internal/External

ASK/FSK/PSK
Internal Keying
1 mHz to 1 MHz
Frequency

No. of Levels 2

Page 6
Modulation Characteristics

Carrier Waveform Pulse

Modulation Source Internal/External

Internal Modulating Sine, Square, Triangle, UpRamp, DnRamp, Noise,

PWM Waveform Arb

Internal Modulation
1 mHz to 1 MHz
Frequency

Width Deviation 0% to 49.99% of the pulse period

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

SUM Sum Source Sine, Square, Ramp, Noise, Arb, channel waveform

Sum Ratio 0% to 100% of the amplitude setting (Vpp)

Burst Characteristics
Burst Characteristics

Carrier Waveform Sine, Square, Ramp, Noise, Arb (except DC)

Burst Count 1 to 1,000,000/Infinite

Internal Burst 4 μs to 8000 s

Period

Burst Phase -360° to +360°, 0.01° resolution

Trigger Delay 0 ns to 20 s

Gate Source External trigger

Trigger Source Internal, External leading edge, external trailing edge, Manual

Sweep Characteristics
Sweep Characteristics

Type Linear, Log, Step

Carrier Waveform Sine, Square, Ramp, Arb (except DC)

Sweep Time 1 ms to 250,000 s

Page 7
Sweep Characteristics

Start/Stop
Consistent with the upper/lower limit of the corresponding carrier frequency
Frequency

Hold/Return Time 0 s to 3600 s

Orientation Up/Down

Trigger Source Internal, External leading edge, external trailing edge, Manual

Mark Falling edge of the sync signal (programmable)

Sequence Characteristics
Sequence Characteristics

Sample Rate 1 μSa/s to 312.5 MSa/s

Sample Rate
10-6 Sa/s
Accuracy

Sample Rate
1 μSa/s or 12 digits
Resolution

Sequence Length 32 pts/CH to 2 Mpts/CH (8Mpts/CH optional)

No. of Waveform
64
Entries

Loop 0 to 256

Filter Mode Normal, Step, Interpolation

Frequency Counter
Frequency Counter

Frequency, period, positive pulse width, negative pulse width,

Measurement Function
duty cycle

Input Impedance 50 Ω ± 2%, 1 MΩ ± 5%

0 to 250 MHz: 7 digits

Counter Accuracy
250 MHz to 500 MHz: 6 digits

Trigger Level 0V

Page 8
Frequency Counter

50 Ω Load DC coupling
Input Coupling
Mode
1 MΩ Load AC/DC coupling

50 Ω Load 100 mVpp to 2 Vpp

Input Amplitude
1 MΩ Load 500 mVpp to 5 Vpp (Vac + dc)

50 Ω Load 4 Vpp
Input Disruptive
Level
1 MΩ Load 5 Vpp

0 to 250 MHz
50 Ω Load
Input Frequency 250 MHz to 500 MHz
Range Mode
1 MΩ Load 0 to 250 MHz

50 Ω Load DC to 500 MHz

Effective Signal
Frequency
1 MΩ Load DC to 250 MHz (DC coupling)

HF Reject 60 kHz/None (available only for 1 MΩ load)

Connector BNC, on the rear panel

AUX IN/OUT Characteristics

AUX IN/OUT Characteristics

ASK, FSK, PSK: 3.3 V logic level

Input Range
AM, FM, PM, PWM: ±5V full range
External
Modulation Input Frequency Range DC to 100 kHz (1 MSa/s)

Input Impedance 10 kΩ ± 10%

Page 9
AUX IN/OUT Characteristics

Level TTL-compatible

Impedance 10 kΩ ± 10%

Edge Positive/negative(selectable)

Min. Pulse Width 100 ns

External Trigger/
Gated Burst Input Trigger Delay
0 ns to 20 s
Range

Trigger Delay
100 ps or 5 digits
Resolution

Typical (trigger input to signal output, Burst mode), 1.5

Jitter (rms)
ns

Level TTL-compatible

Trigger Output Output Impedance 50 Ω ± 5%

Jitter (rms) Typical (Continuous mode), 1.5 ns

Level TTL-compatible
Sync Output
Impedance 50 Ω ± 5%

10 MHz Reference In/Out Characteristics

10 MHz In/Out Characteristics

Impedance 1 kΩ

Input Coupling AC coupling

External Reference
Input Required Input
100 mVpp to 5 Vpp
Voltage

Lock Range 10 MHz ± 100 Hz

Impedance 50 Ω

Internal Reference
Output Coupling AC coupling
Output

Level Typical (50 Ω Load), 1.2 Vpp

Page 10
Protection
Protection
Occurred when:
The instrument amplitude setting is greater than 4 Vpp or the output AC +
DC is greater than |2 Vdc| and the input voltage is greater than ±12 x (1 ±
Overvoltage 5%)V (<10 kHz). Disruptive voltage: ±18(Vac + dc)
Protection
The instrument amplitude setting is less than or equal to 4 Vpp or the output
AC + DC is less than |2 Vdc| and the input voltage is greater than ±2.5 x (1 ±
5%)V (<10 kHz). Disruptive voltage: ±3.5(Vac + dc)

NOTE:

[1]: 1 kHz Sine, amplitude > 1 mVpp, 0 V offset, unit: Vpp

[2]: dBm is available only when the load impedance is not set to HighZ; Vrms is not available for Arb;
Vpp and V (high level and low level) are available for all waveform types.

Page 11
General Specifications
Characteristics
Characteristics

Display 7-inch touch screen, 1024 x 600 resolution

Stabilization Time At least 20-minute warm-up

Power Supply
Power Supply

Power Interface USB Type-C Interface

Input Voltage USB PD 15 V, 3 A

Consumption 45 W (max.)

Interface
Interface

LAN 1 at rear panel, 10/100 BASE-T port, supporting LXI-C

Support Web Control (input the IP address of the instrument into the Web
Web Control
browser to display the operation interface)

USB Host 1 at front panel

USB Device 1 at rear panel, supporting TMC

Mechanical Characteristics
Mechanical Characteristics

Dimension 266 mm (W) x 165 mm (H) x 80 mm (D)

Package excluded: <1.78 kg

Weight
Package included: <2.78 kg

Page 12
Environment
Environment

Operating 0℃ to +40℃
Temperature
Range
Non-operating -20℃ to +60℃

Operating 0℃ to +40℃, ≤80% RH (without condensation)

Humidity Range -20℃ to 40℃, ≤90% RH (without condensation)

Non-operating
below 60℃, ≤80% RH (without condensation)

Operating Below 3,000 m

Altitude
Non-operating Below 12,000 m

Page 13
Regulation Standards
Regulation Standards

Compliant with EMC Directive (2014/30/EU), compliant with or higher than

the standards specified in EN 61326-1: 2013, EN 61326-2-1:2013, EN IEC
61000-3-2:2019+A1, EN 61000-3-3:2013+A1:2019

CISPR 11:2009+A1 Class A

EN IEC 61000-3-2:2019+A1 Harmonics, Class A

EN 61000-3-3:2013+A1:2019 Voltage flicker

±4.0 kV (contact discharge), ±8.0 kV

EN 61000-4-2:2009
(air discharge)

10 V/m (80 MHz to 1 GHz); 3 V/m (1.4

Electromagnetic EN 61000-4-3:2006+A1+A2
GHz to 6 GHz)
Compatibility
EN 61000-4-4:2004+A1 2 kV power cord

1 kV (phase-to-neutral voltage); 2 kV
EN 61000-4-5:2006 (phase-to-earth voltage); 2 kV
(neutral-to-earth voltage)

EN 61000-4-6:2009 10 V, 0.15 MHz to 80 MHz

Voltage dip: 0% UT during half cycle;

0% UT during 1 cycle; 70% UT during
EN 61000-4-11:2004 25 cycles

Short interruption: 0% UT during 250

cycles

EN 61010-1:2010+A1:2019

IEC 61010-1:2010+A1:2016
Safety
UL 61010-1: 2012 R7.19

CAN/CSA-C22.2 NO. 61010-1-12 + GI1 + GI2 (R2017) + A1

Meets GB/T 6587; class 2 random

Vibration
Meets MIL-PRF-28800F and IEC60068-2-6; class 3 random

Meets GB/T 6587-2012; class 2 random

Meets MIL-PRF-28800F and IEC 60068-2-27; class 3 random

Shock
(in non-operating conditions: 30 g, half sine, 11 ms duration, 3 shocks along
the main axis, a total of 18 vibrations)

Page 14
Warranty and Calibration Interval
Warranty and Calibration Interval

Warranty 3 years (excluding the accessories)

Recommended
12 months
Calibration Interval

Page 15
Order Information and Warranty
Period

Order Information

Order Information Order No.

Model

25 MHz Bandwidth, 625 MSa/s Sample Rate, Single-channel DG821 Pro

25 MHz Bandwidth, 625 MSa/s Sample Rate, Dual-channel DG822 Pro

50 MHz Bandwidth, 625 MSa/s Sample Rate, Dual-channel DG852 Pro

Standard Accessories

Power Adaptor Conforming to the Standard of the Destination

——
Country

USB Cable ——

One BNC Cable CB-BNC-BNC-MM-100

Upgrade Options

8 Mpts/CH Memory Depth Upgrade Option DG800Pro-3RL

Two-channel Upgrade Option (for DG821 Pro only) DG800Pro-DCH

Optional Accessories

40 dB Attenuator (50 Ω, 1 W) RA5040K

Warranty Period

Three years for the mainframe, excluding the accessories.

Page 16
Option Ordering and Installation
Process

1. According to the usage requirements, please purchase the specified function options from RIGOL

Sales Personnel, and provide the serial number of the instrument that needs to install the option.

2. After receiving the option order, the RIGOL factory will mail the paper software product

entitlement certificate to the address provided in the order.

3. Log in to RIGOL official website for registration. Use the software key and instruments serial

number provided in the entitlement certificate to obtain the option license code and the option

license file.

4. Download the option license file to the root directory of the USB storage device, and connect the

USB storage device to the instrument properly. After the USB storage device is successfully

recognized, the Option install menu is activated. Press this menu key to start installing the

option.

Page 17
INDIA Malaysia -RIGOL Factory NORTH AMERICA
RIGOL TECHNOLOGIES INDIA PVT. LTD. RIGOL TECHNOLOGIES (MALAYSIA) SDN. BHD RIGOL TECHNOLOGIES, USA INC.
2831, 1st Floor, MOCE Layout, Sahakarnagar Plot 12 & 13, Hilir Sungai Kluang 3, 10220 SW Nimbus Ave.
Bengaluru-560092, Karnataka, India. Bayan Lepas Free Industrial Zone Phase 4, Suite K-7
Contact : +91-8884000028/9506111118 Bayan Lepas, Penang, Malaysia-11900. Portland, OR 97223
Email : [email protected] Phone : +604-6119929 / +604-6441181 Tel: +1 (440) 232-4488
Website : https://in.rigol.com/ Email: [email protected] Fax: +1-877-4-RIGOL-1
Email: [email protected]

JAPAN KOREA EUROPE

RIGOL JAPAN CO., LTD. RIGOL KOREA CO., LTD. RIGOL TECHNOLOGIES EU GmbH
5F, 3-45-6, Minamiotsuka, Toshima-Ku, 508, BalsanW-Tower, Carl-Benz-Str. 11
Tokyo, 170-0005, Japan 222, Gonghang-daero, Seoul, Korea 82205 Gilching
Tel: +81-3-6262-8932 Tel: +82-2-6953-4466 Germany
Fax: +821-3-6262-8933 Fax: +82-2-6953-4422 Tel: +49(0)8105-27292-0
Email: [email protected] Email: [email protected] Email: [email protected]