MATERIAL SAFETY DATA SHEET
ASIAN FILLING PUTTY
1. IDENTIFICATION OF THE SUBSTANCE/MIXTURE AND OF THE
COMPANY/ UNDERTAKING
Identification of the substance or mixture
Product name : ASIAN Paints Trucare Wall PUTTY
Product code : 00790908
Chemical name : Not available.
Synonyms : Not available.
Chemical formula : Not applicable.
CAS number : Not applicable.
Use of the substance/mixture : Painting/Coating
Company/undertaking identification
Manufacturer : Asian Paints
Ltd.
6A,
Shantinagar.
Opp Hotel Grand Hyatt,
Santacruz (E), P.O. Box No. 6818,
Mumbai 400 055
Tel No. 091 22 39818000
Fax No. 091 22 39818888
Supplier : Asian Paints
Ltd.
6A,
Shantinagar.
Opp Hotel Grand Hyatt,
Santacruz (E), P.O. Box No. 6818,
Mumbai 400 055
Tel No. 091 22 39818000
Fax No. 091 22 39818888
e-mail address of :
person responsible for
[email protected]this SDS
Emergency telephone : +091 22 39814000
number (with hours
of operation)
2. HAZARDS IDENTIFICATION
Risk phrases : This product is not classified according to EU legislation.
Additional hazards : None known.
See Section 11 for more detailed information on health effects and symptoms.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance/preparation : Mixture
There are no ingredients present which, within the current knowledge of the supplier and in the
concentrations applicable, are classified as hazardous to health or the environment and hence require
reporting in this section.
4. FIRST AID MEASURES
Inhalation Eye contact
Ingestion
Skin contact
: Remove attention if symptoms occur.
victim to : Wash out mouth with water. Remove victim to fresh air and keep at rest
fresh air in a position comfortable for breathing. If material has been swallowed
and keep at and the exposed person is conscious, give small quantities of water to
rest in a drink. Do not induce vomiting unless directed to do so by medical
position personnel. Get medical attention if symptoms occur.
comfortable
: Flush contaminated skin with plenty of water. Remove contaminated
for
clothing and shoes. Get medical attention if symptoms occur.
breathing.
Get : Immediately flush eyes with plenty of water, occasionally lifting the upper
medical and lower eyelids. Check for and remove any contact lenses. Get medical
attention if irritation occurs.
See Section 11 for more detailed information on health effects and symptoms.
Date of issue/Date of revision : 2/5
8/24/2014.
5. FIRE-FIGHTING MEASURES
Extinguishing media
Suitable : Recommended: alcohol-resistant foam, CO2, powders, water
Not suitable : spray. Do not use water jet.
Special exposure hazards : No specific fire or explosion hazard.
Promptly isolate the scene by removing all persons from the vicinity of
the incident if there is a fire. No action shall be taken involving any
personal risk or without suitable training.
Hazardous thermal : Decomposition products may include the following
decomposition products materials: carbon dioxide
carbon monoxide
metal oxide/oxides
Special protective : Fire-fighters should wear appropriate protective equipment and self-
equipment for fire- contained breathing apparatus (SCBA) with a full face-piece operated in
fighters positive pressure mode. Clothing for fire-fighters (including helmets,
protective boots and gloves) conforming to European standard EN 469
will provide a basic level of protection for chemical incidents.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions : No action shall be taken involving any personal risk or without suitable
training.
Evacuate surrounding areas. Keep unnecessary and unprotected
personnel from entering. Do not touch or walk through spilled material.
Environmental precautions Put on appropriate personal protective equipment (see Section 8).
: Avoid dispersal of spilled material and runoff and contact with soil,
waterways, drains and sewers. Inform the relevant authorities if the
Methods for cleaning up product has caused environmental pollution (sewers, waterways, soil or
air).
Small spill : Move containers from spill area. Vacuum or sweep up material and
place in a designated, labeled waste container. Dispose of via a
licensed waste disposal contractor.
Large spill : Move containers from spill area. Prevent entry into sewers, water courses,
basements or confined areas. Vacuum or sweep up material and place in
a designated, labeled waste container. Dispose of via a licensed waste
disposal contractor.
7. HANDLING AND STORAGE
Handling : Put on appropriate personal protective equipment (see Section 8). Eating,
drinking and smoking should be prohibited in areas where this material is
handled, stored and processed. Workers should wash hands and face
before eating, drinking and smoking. Remove contaminated clothing and
protective equipment before entering eating areas.
Storage : Store in accordance with local regulations. Store in original container
protected from direct sunlight in a dry, cool and well-ventilated area,
away from incompatible materials (see Section 10) and food and drink.
Keep container tightly closed and sealed until ready for use. Containers
that have been opened must be carefully resealed and kept upright to
prevent leakage. Do not store in unlabeled containers. Use appropriate
containment to avoid environmental contamination. Store between the
following temperatures: 10 to 40°C (50 to 104°F).
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
No exposure limit value
known. No exposure limit
value known. monitoring
Recommended : If this product contains ingredients with exposure limits, personal,
procedures workplace atmosphere or biological monitoring may be required to
determine the effectiveness of the ventilation or other control measures
and/or the necessity to use respiratory protective equipment. Reference
should be made to monitoring standards, such as the following:
European Standard EN 689 (Workplace atmospheres - Guidance for the
assessment of exposure by inhalation to chemical agents for comparison
with limit values and measurement strategy) European Standard EN
14042 (Workplace atmospheres - Guide for the application and use of
procedures
Date for the
of issue/Date of revision : 3/5
assessment of 8/24/2014.
exposure to chemical
and biological
agents) European
Standard EN 482
(Workplace
atmospheres -
General
requirements for the
performance of
procedures for the
measurement of
chemical agents)
Reference to national
guidance
Date of issue/Date of revision : 4/5
8/24/2014.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
documents for methods for the determination of hazardous substances will
also be
required.
Exposure controls
Occupational exposure
controls : No special ventilation requirements. Good general ventilation should be
sufficient to control worker exposure to airborne contaminants. If this
product contains ingredients with exposure limits, use process
enclosures, local exhaust ventilation or other engineering controls to
keep worker exposure below any recommended or statutory limits.
Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical
products, before eating, smoking and using the lavatory and at the end of
the working period.
Appropriate techniques should be used to remove potentially
contaminated clothing. Wash contaminated clothing before reusing.
Respiratory protection : Ensure that eyewash stations and safety showers are close to the
workstation location.
Use a properly fitted, particulate filter respirator complying with an
approved standard if a risk assessment indicates this is necessary.
Respirator selection must be based on known or anticipated exposure
levels, the hazards of the product and the safe working limits of the
selected respirator.
Hand protection : Chemical-resistant, impervious gloves complying with an approved
standard should be worn at all times when handling chemical products if
a risk assessment indicates this is necessary.
Eye protection : Safety eyewear complying with an approved standard should be used
when a risk assessment indicates this is necessary to avoid exposure to
liquid splashes, mists or dusts. If contact is possible, the following
protection should be worn, unless the assessment indicates a higher
degree of protection: safety glasses with side- shields.
Skin protection : Personal protective equipment for the body should be selected based on
the task being performed and the risks involved and should be approved
by a specialist before handling this product.
Environmental exposure : Emissions from ventilation or work process equipment should be checked
controls to ensure they comply with the requirements of environmental
protection legislation. In some cases, fume scrubbers, filters or
engineering modifications to the process equipment will be necessary to
reduce emissions to acceptable levels.
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical state : POWDER
Odor : Not available.
Odor threshold : Not available.
pH : 8 to 10.5
Boiling point : Not available.
Melting point : Not available.
Flash point : Not available.
Vapor pressure : Not available.
Relative density : 2.744
Solubility : Not available.
Vapor density : Not available.
Evaporation rate : >1 (Butyl acetate=1 = 1)
Auto-ignition temperature : Not available.
Density : 2.744083395 g/cm³ [30°C (86°F)]
Flammability : Not available.
10. STABILITY AND REACTIVITY
Chemical stability : The product is stable.
Possibility of : Under normal conditions of storage and use, hazardous reactions will not
hazardous reactions occur.
Conditions to avoidof revision : No specific: data.
Date of issue/Date 5/5
Materials to avoid : No known 8/24/2014.
incompatibility
Date of issue/Date of revision : 6/5
8/24/2014.
11. TOXICOLOGICAL INFORMATION
Potential acute health effects
Inhalation : No known significant effects or critical hazards.
Ingestion : No known significant effects or critical hazards.
Skin contact : No known significant effects or critical hazards.
Eye contact : No known significant effects or critical hazards.
Potential chronic health effects
Chronic effects : No known significant effects or critical
Carcinogenicity : hazards. No known significant effects or
Mutagenicity : critical hazards. No known significant
Teratogenicity : effects or critical hazards. No known
significant effects or critical hazards.
Developmental effects : No known significant effects or critical
hazards. Fertility effects : No known significant effects or critical
hazards. Over-exposure signs/symptoms
Inhalation : No specific data.
Ingestion : No specific data.
Skin : No specific data.
Eyes : No specific data.
12. ECOLOGICAL INFORMATION
Ecotoxicity : No known significant effects or critical hazards.
Aquatic ecotoxicity
Conclusion/Summary : Not available.
Other adverse effects : No known significant effects or critical hazards.
13. DISPOSAL CONSIDERATIONS
Methods of disposal : The generation of waste should be avoided or minimized wherever
possible. Waste product residues should not be disposed of via the sewer
but processed in a suitable effluent treatment plant. Dispose of surplus
and non-recyclable products via a licensed waste disposal contractor.
Disposal of this product, solutions and any by-products should at all times
comply with the requirements of environmental protection and waste
disposal legislation and any regional local authority requirements. Waste
packaging should be recycled. Incineration or landfill should only be
considered when recycling is not feasible. This material and its container
must be disposed of in a safe way. Empty containers or liners may retain
some product residues. Avoid dispersal of spilled material and runoff and
contact with soil, waterways, drains and sewers.
14. TRANSPORT INFORMATION
International transport regulations
This preparation is not classified as dangerous according to international transport regulations
(ADR/RID, ADNR, IMDG and IATA ). Transport in accordance with ADR/RID, ADNR, IMDG and IATA and
national regulation.
Always transport in closed containers that are upright and secure. Ensure that persons transporting
the product know what to do in the event of an accident or spillage
15. REGULATORY INFORMATION
Risk phrases : This product is not classified according to EU legislation.
Product use : Consumer applications.
16. OTHER INFORMATION
National Fire Protection :
Association (U.S.A.) Health
Date of issue/Date of revision : 7/5
8/24/2014.
0 Flammability
0 0 Instability/Reactivity
Special
Date of issue/Date of revision : 8/5
8/24/2014.
16. OTHER INFORMATION
History
Date of printing : 8/24/2014.
Date of issue/ Date of : 8/24/2014.
revision
Date of previous issue : 8/18/2014.
Version : 2
Indicates information that has changed from previously issued version.
Disclaimer
Information contained in this material safety data sheet is believed to be reliable and given in good faith,
but no representation, guarantee or warranties of any kind are made as to its accuracy, suitability for a
particular application or results to be obtained from them.
The user of this material decides what safety measures are necessary to safely use this material, either alone
or in combination with other materials.
Asian Paints Limited makes no warranties expressed or implied in respect of the adequacy of this document
for any particular purpose.
ASIAN FILLING PUTTY
