01) In massive structures like Corewall, concrete should be placed in _____

A: Edge layers

B: Longitudinal layers

C: Horizontal layers

D: place all in one time

02) We should not use longitudinal reinforcement bars in column less than 12mm
______

A: to avoid cracks

B: avoid crush

C: we can use 10mm

D: due to buckling

03) The minimum cube strength of concrete used for a prestressed member is _____
Kg/cm2

A: 50

B: 150

C: 250

D: 350

04) The number of treads in a flight of stairs is equal to _____

A: risers in flight

B: riser plus 2

C: riser plus 1

D: riser minus 1

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
05) For initial estimate of non-cantilever beam design the width is taken as ______

A: 1/15th of Span

B: Span/20

C: Span/10

D: Span/30

06) The formwork from the roof slabs excluding props can be removed only after _____

A: 3 days

B: 7 days

C: 21 days

D: 14 days

07) In fumigation process for the timber truss is cover with chemicals in tablets form
for ____

A: 3 days

B: 48 hours

C: 12 hours

D: 24 hours

08) If d is the distance between flange angles, the vertical sti eners in plate girders are
spaced not greater than _____

A: d

B: 1.25d

C: 1.75d

D: 1.5d

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
09) The yield strength of ASTM A516 Grade 60 steel is ______N/mm2

A: 200

B: 250

C: 516

D: 265

10) When a large value of radius of gyration is not required than ____

A: Channels are placed back to back

B: channel flanges are kept outward

C: Channel flanges are kept inward

D: none of them

11) In o shore projects, piles can be driven down to a maximum of _____ meter.

A: 90m

B: 100m

C: 200

D: 150m

12) The maximum deflection for cantilever beam under uniformly distributed load is
____

A: PL3/48EI

B: PL3/3EI

C: wL2/2

D: WL4/8

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
13) As per DM requirement, the modification factor for post tensioning slab is ____

A: 0.35

B: 0.25

C: 0.7

D: 0.5

14) As per DM requirements, the maximum angle of excavation is ___

A: 30

B: 35

C: 45

D: 40

15) As per DIN 1048 standards, water penetration at 28 days test should not exceed
max of ____

A: 5mm

B: 7mm

C: 15mm

D: 10mm

16) As per ASTM C1202, the rapid chloride penetration at 28 days test for RCC piles
should not exceed maximum of ____ Coulombs.

A: 700

B: 1500

C: 1000

D: 1200

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
17) The maximum acceptable settlement for the piles under working loads is ____

A: 12mm

B: 10mm

C: 25mm

D: 8mm

18) The area of main reinforcement bars for piles shall not be less than ____ of
sectional Area.

A: 2%

B: 3%

C: 1.5%

D: 1%

19) Percent elongation of steel reinforcement is a measure of _______

A: toughness

B: strength

C: weakness

D: ductility

20) The percent Elongation of mild steel is given by the _____

Answer. % Elongation= ((final gage length - initial gage length)/initial gage length)x100

= ( ΔL/L)x100

21) Which tests are performed on steel reinforcement before use?

A: Tensile test

B: bending test

C: compression test

D: All

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
22) The minimum acceptable value in case of high strength reinforcement is ___
N/mm2

A: 250

B: 360

C: 550

D: 460

23) In case of built-up section As per DM requirements, the min thickness of steel
plate is to be ____

A: 10mm

B: 8mm

C: 4mm

D: 6mm

24) The ultimate deflection for steel structure due to live loads As per DM rules is ____

A: L/150 B:

L/200

C: L/250

D: L/360

25) The allowable deflection for exterior walls with flexible finishes due to wind load is
____

A: L/240

B: L/600

C: L/360

D: L/120

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
26) If you have residential building G+5 existing and you want to add one more floor
what step will you follow for check?

Ans. These 4 steps are important.

A: Check soil capacity according new loads

B: take sample for core test

C: redesign foundation according to new fuc

D: redesign the column according to new loads

27) Draw Shear force and bending moment diagram for the following,

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
28) Draw Shear force and bending moment diagram for the following Cantilever
subjected to the Uniformly distributed load of W/M throughout the length.

29) Draw Shear force and bending moment diagram for the following Cantilever
subjected to the Uniformly distributed load From the length of L/2 From the fixed end.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
30) Draw Shear force and bending moment diagram for the following Cantilever
subjected to the Uniformly Varying load with the zero intensity at fixed end and w/m
with the free end.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
31) Draw Shear force and bending moment diagram for the following Cantilever
subjected to moment m at free end.

32) Draw Shear force and bending moment diagram for the following Simply
supported beam with a concentrated load W at mid span.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
33) Draw Shear force and bending moment diagram for the following Simply
supported beam subjected to uniformly distributed load throughout.

34) Draw Shear force and bending moment diagram for the following Simply
supported beam subjected to uniformly distributed load on the half of the span.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
35) Draw Shear force and bending moment diagram for the following Simply
supported beam subjected to uniformly varying load from zero at either end to w/m at
mid span.

36) Draw Shear force and bending moment diagram for the following Simply
supported beam subjected to uniformly varying load from zero at one support to w/m
at other support.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
37 Draw Shear force and bending moment diagram for the following Simply supported
beam subjected to couple M at mid span.

38) Draw Shear force and bending moment diagram for the following Simply
supported beam subjected to couple M not at mid span.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
39) Draw Shear force and bending moment diagram for the following overhanging
beam subjected to uniformly distributed load throughout.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
40) A cantilever beam is loaded at the far end by 100 N load and length is 10m the
maximum bending moment produced is ____

A: 2KNm

B: 10KNm

C: 0.1KNm

D: 1KNm

41) The dynamic analysis is performed for irregular buildings of storey above ____

A: 10m

B: 15m

C: 25m

D: 19.8m

42) The toe depth of pile with respect to diameter of pile in the rock soil is ___

A: 3D

B: 1D

C: 5D

D: 2D

43) Maximum storey drift ΔM for time period T < 0.7sec is ____

Ans. ΔM= 0.7xRxΔS > 0.025H

44) The maximum vertical reinforcement in columns in case of overlap is ___

A: 8%

B: 5%

C: 1%

D: 4%

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
45) The maximum deflection for piles as per DM rules is ____

A: 10%

B: 5%

C: 0.1%

D: 1%

46) The maximum length anchors in shoring system as per DM requirements is ___

A: 7m

B: 5m

C: 15m

D: 10m

47) The e ect of liquefaction on soil due to EQ load is ____

A: land sliding

B: loss of sti ness

C: loss of Bearing Capacity

D: All

48) The minimum between piles as per DM requirements in terms of diameter is ___

A: 1D

B: 2D

C: 1.5D

D: 2.5D

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
49) The Dubai municipality has announced that buildings taller than 10 floors as well
as schools and hospitals should withstand Earthquake of magnitude ____

Ans. 5 - 5.9 (zone 2B)

50) Burj Khalifa tower can withstand wind speed upto ____ Km/hr

A: 100

B: 200

C: 140

D: 160

51) In steel structures Bolts A325, A449 and A490 Are _____ bolts.

A: low strength

B: medium strength

C: low carbon

D: high strength

52) Which of the following is not the US bolt grade?

A: 2

B: 5

C: 8

D: 3

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
53) A325 bolt is made of medium carbon steel and its tensile strength ___ with
increase in dia.

A: increase

B: remain same

C: first increase than decrease

D: decrease

54) The maximum tensile strength of ASTM A36 steel is ____ MPa

A: 250

B: 300

C: 460

D: 550

55) As per BS 4360, the allowable strength for 16mm thick grade 55 steel plate is
____MPa

A: 275

B: 550

C: 375

D: 450

56) Bolts are designed to resist failure in ____

A: shearing

B: bearing

C: tearing

D: All

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
57) The Clear cover provided to beam is _____

A: 20mm

B: 45mm

C: 50mm

D: 25mm

58) The thickness of external fence wall plaster wall should be _____

A: 10mm

B: 12mm

C: 15mm

D: 20mm

59) The gate level of the villa should be above from the road level by ____

A: 10cm

B: 15cm

C: 20cm

D: 30cm

60) The correct definition of durability of concrete is ______

A: The capability of concrete to resist weathering action.

B: Ability to resist against chemical attack and abrasion.

C: Ability to bear heavy load

D: Both A and B

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
61) The 6 concrete cubes are casted and are tested after ____

A: 3 days

B: 7 days

C: 28 days

D: 7 and 28 days

62) When water content in concrete increase than strength _____

A: increase

B: no change

C: no relation

D: decrease

63) Moulds (shutters) of beams sides can be dismantled after minimum … days from
casting

a) 2

b)1

b) 7

c) 14

64. The eave connection is a connection between

a) Beam to Beam Connection

B) beam to column connection

c) beam to slab connection

d) none of the above

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
65. Minimum depth of pile head inside the pile cap

a) 150mm

b) 100 mm

c) 50 mm

d) 75 mm

66. In secant piles minimum overlap for the piles

a) 150 mm

b) 100 mm

d) 75 mm

67. The minimum overlap splice for pile reinforcement

a) 60pile dia

b) 50pila dia

c) 45pile dia

d) 35pile dia

68. The level of shoring RC piles for the road should be below G.L by

a) 1 m

b) 1.5 m

c) 1.2m

d) None

69. Materials used in between of H and I beam of soldier pile

a) Concrete

b) Timber

c) Steel

d) All of above
Prepared By: Engr Said Saqib Khan
DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
70. How many cube required to be taken for 110 m3 poured in one day ?

a) 12,

B. 6,

c) 10,

d) 3,

71. What is the common type of shoring?

a) Contiguous,

B. secant,

c) solider,

d) Sheet piles,

e) None

72. What is the common type of dewatering?

a) Deep wells,

B. well point,

c) surface dewatering,

d) Eductor System

73. What is the materials to be used in I beam shoring?

a) Timber,

b) concrete,

c) steel sheets,

D. all

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
74. Cement hydration is?

A. Cement with water,

b) cement with base,

c) cement with acid,

d) cement with chemical

75. The length between C.G of tension and C.G of compression in plat called as?

a) Critical depth,

B. e ective depth,

c) anchor length,

d) normal length

76. The ultrasonic test shall be carried out in minimum dia of piles

A. 20 cm

b) 30cm,

c) 100cm

d) non

77. The splicer of piles reinforcement shall be?

a) 40D,

B. 50D,

c) 20D,

d) 60D

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
78. Shotcrete is Used in ……….

a) Repairing Surface.

b) Dam Surface.

c) Curved Decorative Surface.

D. All of Above.

79. Rebounded Schmidt Hummer Test is

a) (Non – Destructive test).

80. First Compression Test on Cubes IS Done after ….

a) 3 days.

b) 5 days.

C. 7 days.

d) 9 days.

81. Density of Aluminium is ………….

a) 3500 Kg/m3.

B. 2700 Kg/m3.

c) 2500 Kg/m3.

d) 3000 Kg/m3.

82. Core Samples Should be Taken after ……….

a) 7 days.

b) 14 days.

c) 21 days.

D. 28 days.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
83. Bitumen is Used to Provide ……….

a) Decorative Surface.

b) Shining Surface.

c) Smooth Surface.

D. Protective Surface.

84. Modulus of Elasticity of Concrete is …….

a) 5700 √fc` N/mm2.

b) 2900 N/mm2.

c) 210 N/mm2.

D. 4700 √fc` N/mm2.

85. The Poisson Ratio for Structural Steel is …….

A. 0.3.

b) 0.4.

c) 0.5.

d) 0.6.

86. How Many Cubes Samples Required for 110 m3 of Concrete on a single Day?

a) 12 Cubes.

B. 6 Cubes.

c) 18 Cubes.

d) 9 Cubes.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
87. Adding more Water to Concrete mix its Strength ………

a) Increase.

B. Decrease.

c) Remain Same.

d) May Increase or May Decrease.

88. The Average Strength of Cubes at the End of 28 Days Should be ………

a) Greater than fc` by 15%.

B. Greater than or Equal to fc`.

c) Equal to fc` or less by 15%.

d) Greater than fc` 1.15 times.

89. Density of ACC Blocks is ………

a) 300 kg/m3.

b) 400 kg/m3.

c) 500 kg/m3.

D. 600 kg/m3.

90. Maximum Deflection For Piles as per DM rules is ……….

a) 5 %.

b) 4 %.

c) 2 %.

D. 1 %.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
91. Maximum Allowable Settlement in Raft Foundation is ……….

a) 10 mm.

b) 20 mm.

c) 30 mm.

D. 50 mm.

92. In Concentric Footing, The Column is at the ……

a) Edge of Footing.

b) Corner OF Footing.

C. Centre of Footing.

d) Anywhere in Footing.

93. Amount of Steel in Flat Slab as per DM rules is.

A. 160-185 kg/m3.

b) 350-500 kg/m3.

c) 50-85 kg/m3.

d) 100-120 kg/m3.

94. Compacting of Concrete is Done to ………

a) Increase Strength.

b) Increase Durability.

c) Remove Air.

D. All Of Above.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
95. Composite piles are suitable for ...............

a) Maximum Design Load

b) Compacting the soil

c. Protect Water Structure

D. The project above the water table

96. What`s the E ect of Corrosion in Steel on Concrete Element?

a) Damage of Concrete.

b) Cracking.

c) Deflection is more.

D. All of Above.

97. If Temperature Of the Mix above 32˚C during Casting, then How to Reduce it ?

a) Adding Water.

b) Adding Silica.

c) Adding fly ash.

D. Adding Ice.

98. Choose the Correct Statement for Concrete ………

A. Concrete is Strong in Compression but Weak in Tension.

99. Why Contractors use Blanket over Fresh Concrete?

a) To Increase Evaporation.

B. To Reduce Evaporation.

b) To Avoid Sulphate Attack.

c) To Get Rapid Hard.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
100. Density of RCC is ………

a) 2300 kg/m3.

b) 2400 kg/m3.

c) 2600 kg/m3.

D. 2500 kg/m3.

101. The Clear Cover Provided to Footing is ………

a) 65 mm.

b) 55 mm.

c) 40 mm.

D. 75 mm.

102. Honeycomb Occur in Concrete Element Due to ….

a) Improper Vibration.

b) Use Very Sti Concrete mix.

c) Less Clear Cover to Steel.

D. All of Above.

103. Which Part of Building Transfer Loads below The Ground?

a) Sub-structure.

b) Super-structure.

C. Foundation.

d) Plinth.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)
104. The Most Common Type of Footing used in building is …….

a) Raft.

B. Isolated.

c) Strap.

d) Combined.

Prepared By: Engr Said Saqib Khan

DM Approved : (G+Unlimited Consultant Supervision) DM Approved: (G+12 Building Contracting Licns)
Rak Munci: (G+unlimited Building Contracting) Dubai Civil Defense Delegated Licns
ADM Munci: (Practicing Permit) Shj Muncipilty : (G+4 Licns)
Email: [email protected] Project Management Professional (PMP Certified)