DRIVER INFORMATION & MULTIMEDIA

SECTION
WARNING CHIME SYSTEM
WCS B

E
CONTENTS
HOW TO USE THIS MANUAL ...................... 3 DIAGNOSIS SYSTEM (COMBINATION F
METER) ............................................................. 21
APPLICATION NOTICE ...................................... 3
Information ................................................................ 3 TYPE A .......................................................................21 G
TYPE A : CONSULT Function .................................21
PRECAUTION ............................................... 4
TYPE B .......................................................................24
PRECAUTIONS ................................................... 4 TYPE B : CONSULT Function .................................24 H
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN- DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
SIONER" ................................................................... 4 GENT KEY SYSTEM) ....................................... 28
I
SYSTEM DESCRIPTION .............................. 5 COMMON ITEM .........................................................28
COMMON ITEM : CONSULT Function (BCM -
COMPONENT PARTS ........................................ 5 COMMON ITEM) .....................................................28 J
Component Parts Location ........................................ 5
BUZZER .....................................................................29
Combination Meter .................................................... 5
BUZZER : CONSULT Function (BCM - BUZZER)....29
SYSTEM .............................................................. 7 K
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
WARNING CHIME SYSTEM ....................................... 7 TELLIGENT KEY SYSTEM) ............................. 31
WARNING CHIME SYSTEM : System Description L
...... 7 COMMON ITEM .........................................................31
WARNING CHIME SYSTEM : Circuit Diagram ......... 9 COMMON ITEM : CONSULT Function (BCM -
WARNING CHIME SYSTEM : Fail-Safe ................. 10 COMMON ITEM) .....................................................31
M
PARKING BRAKE RELEASE WARNING CHIME .... 11 BUZZER .....................................................................31
PARKING BRAKE RELEASE WARNING CHIME BUZZER : CONSULT Function (BCM - BUZZER)....32
: System Description ............................................... 11
ECU DIAGNOSIS INFORMATION .............. 33 WCS
SEAT BELT REMINDER WARNING CHIME ............ 13
SEAT BELT REMINDER WARNING CHIME :
COMBINATION METER ................................... 33
System Description ................................................. 13 TYPE A .......................................................................33 O
TYPE A : Reference Value ......................................33
LIGHT REMINDER WARNING CHIME ..................... 15
LIGHT REMINDER WARNING CHIME : System TYPE A : Fail-Safe ..................................................39
TYPE A : DTC Index ................................................39 P
Description .............................................................. 15
TYPE B .......................................................................39
KEY WARNING CHIME ............................................. 16
TYPE B : Reference Value ......................................40
KEY WARNING CHIME : System Description ........ 17
TYPE B : Fail-Safe ..................................................45
REVERSE WARNING CHIME ................................... 18 TYPE B : DTC Index ................................................45
REVERSE WARNING CHIME : System Descrip-
tion .......................................................................... 19 BCM (BODY CONTROL MODULE) ................. 46

Revision: 2012 July WCS-1 N17

 List of ECU Reference ............................................ 46 PARKING BRAKE SWITCH SIGNAL CIR-
CUIT ................................................................... 55
WIRING DIAGRAM ..................................... 47
TYPE A ...................................................................... 55
WARNING CHIME SYSTEM ............................. 47 TYPE A : Diagnosis Procedure ............................... 55
TYPE A : Component Inspection ............................ 55
TYPE A ...................................................................... 47
TYPE A : Wiring Diagram - WITH ENGINE COOL- TYPE B ...................................................................... 55
ANT TEMPERATURE GAUGE - ............................ 48 TYPE B : Diagnosis Procedure ............................... 55
TYPE B : Component Inspection ............................ 56
TYPE B ...................................................................... 48
TYPE B : Wiring Diagram - WITHOUT ENGINE SYMPTOM DIAGNOSIS ............................ 57
COOLANT TEMPERATURE GAUGE - .................. 49
THE PARKING BRAKE RELEASE WARNING
BASIC INSPECTION ................................... 50 CONTINUES SOUNDING, OR DOES NOT
DIAGNOSIS AND REPAIR WORKFLOW ......... 50 SOUND .............................................................. 57
Work Flow ............................................................... 50 Description .............................................................. 57
Diagnosis Procedure ............................................... 57
DTC/CIRCUIT DIAGNOSIS ......................... 52
THE SEAT BELT REMINDER WARNING
POWER SUPPLY AND GROUND CIRCUIT ..... 52 CONTINUES SOUNDING, OR DOES NOT
SOUND .............................................................. 58
COMBINATION METER (TYPE A) ........................... 52 Description .............................................................. 58
COMBINATION METER (TYPE A) : Diagnosis Diagnosis Procedure ............................................... 58
Procedure ............................................................... 52
THE LIGHT REMINDER WARNING DOES
COMBINATION METER (TYPE B) ........................... 52
COMBINATION METER (TYPE B) : Diagnosis
NOT SOUND ...................................................... 60
Procedure ............................................................... 53 Description .............................................................. 60
Diagnosis Procedure ............................................... 60
METER BUZZER CIRCUIT ................................ 54
Component Function Check ................................... 54
THE KEY WARNING DOES NOT SOUND
Diagnosis Procedure ............................................. 54 (WITHOUT INTELLIGENT KEY) ....................... 61
Description .............................................................. 61
Diagnosis Procedure ............................................... 61

Revision: 2012 July WCS-2 N17

 APPLICATION NOTICE
< HOW TO USE THIS MANUAL >
HOW TO USE THIS MANUAL A
APPLICATION NOTICE
Information INFOID:0000000006895246
B
• In this manual, “Idling Stop System” is referred to as “Stop / Start System”.
• Check the vehicle type to confirm the service information in this section.
C
Service information Design of combination meter

E
TYPE A

JSNIA3947ZZ
G

TYPE B
I

J
JSNIA3946ZZ

WCS

Revision: 2012 July WCS-3 N17

 PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000006882363

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.

Revision: 2012 July WCS-4 N17

 COMPONENT PARTS
< SYSTEM DESCRIPTION >
SYSTEM DESCRIPTION A
COMPONENT PARTS
Component Parts Location INFOID:0000000006655863
B

G
JSNIA4562ZZ

Component Function
H
1. Parking brake switch Transmits the parking brake switch signal to the combination meter.
Seat belt buckle switch
2. Transmits the seat belt buckle switch signal (driver side) to the combination meter.
(driver side)
I
ABS actuator and electric Transmits the vehicle speed signal to the combination meter via CAN communication (Models with
3.
unit (control unit) ABS).
Transmits the following signals to the combination meter via CAN communication.
J
4. TCM • Vehicle speed signal (A/T models without ABS or CVT models without ABS)
• Shift position signal (For Hong Kong)
5. Vehicle speed sensor Transmits the vehicle speed sensor signal to the combination meter (M/T models without ABS).
K
Based on the signals received from various units and switches, transmits the buzzer output signal
6. BCM to the combination meter via CAN communication.
Transmits the vehicle speed signal to the combination meter via CAN communication.
Receives a buzzer output signal from the BCM with CAN communication line and sounds the buzzer.
L
FOR CHINA AND AUSTRALIA
• Controls the following with the vehicle speed signal received from ABS actuator and electric unit
(control unit) via CAN communication and the signals from switches. M
- Parking brake release warning chime
- Seat belt reminder warning chime
MODELS WITH ABS EXCEPT FOR CHINA AND AUSTRALIA
• Controls the following with the vehicle speed signal received from ABS actuator and electric unit WCS
(control unit) via CAN communication and the signals from switches.
7. Combination meter
- Parking brake release warning chime
AT MODELS WITHOUT ABS or CVT MODELS WITHOUT ABS
• Controls the following with the vehicle speed signal received from TCM via CAN communication O
and the signals from switches.
- Parking brake release warning chime
M/T MODELS WITHOUT ABS
• Controls the following with the vehicle speed sensor signal received from vehicle speed sensor P
and the signals from switches.
- Parking brake release warning chime

Combination Meter INFOID:0000000006655865

The buzzer (1) for the warning chime system is integrated in the combination meter.

Revision: 2012 July WCS-5 N17

 COMPONENT PARTS
< SYSTEM DESCRIPTION >
TYPE A

JSNIA3921ZZ

TYPE B

JSNIA2928ZZ

NOTE:
To identify combination meter type, refer to WCS-3, "Information".

Revision: 2012 July WCS-6 N17

 SYSTEM
< SYSTEM DESCRIPTION >
SYSTEM
A
WARNING CHIME SYSTEM
WARNING CHIME SYSTEM : System Description INFOID:0000000006655867
B
SYSTEM DIAGRAM
C

JSNIA4563GB

H
COMBINATION METER INPUT/OUTPUT SIGNAL (CAN COMMUNICATION SIGNAL)
Input signal
I
Signal name Transmit unit
ABS actuator and electric unit (control unit) (Mod-
els with ABS) J
Vehicle speed signal
TCM (A/T models without ABS or CVT models
without ABS)
Buzzer output signal BCM K
Shift position signal TCM (For Hong Kong)

Output signal L

Signal name Reception unit

Vehicle speed signal BCM
M

BCM INPUT/OUTPUT SIGNAL (CAN COMMUNICATION SIGNAL)

Input signal WCS

Signal name Transmit unit

O
Vehicle speed signal Combination meter

Output signal
P
Signal name Reception unit
Buzzer output signal Combination meter

COMBINATION METER
The combination meter sounds the alarm buzzer installed in the combination meter when receiving the buzzer
output signal transmitted from each unit.

Revision: 2012 July WCS-7 N17

 SYSTEM
< SYSTEM DESCRIPTION >
BCM
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
WARNING CHIME FUNCTION LIST

Warning functions Out line Warning judgment unit Refer to

WCS-11,
"PARKING
The warning chime sounds when the ignition
BRAKE RE-
switch is in ON position with the parking brake
Parking brake release warning chime Combination meter LEASE WARN-
in operation and the vehicle speed 7 km/h (4.3
ING CHIME :
MPH) or more.
System De-
scription"
Combination meter WCS-13,
(For China and Australia) "SEAT BELT
The warning chime sounds when vehicle
REMINDER
Seat belt reminder warning chime (For speeds reach 15 km/h (9.3 MPH) or more with
WARNING
China, Australia and Hong Kong) the ignition switch ON and the driver unbuck-
BCM (For Hong Kong) CHIME : Sys-
led.
tem Descrip-
tion"
WCS-15,
"LIGHT RE-
The warning chime sounds when the ignition
MINDER
switch is in OFF or ACC position with the com-
Light reminder warning chime BCM WARNING
bination switch (lighting switch) in the 1st or
CHIME : Sys-
2nd position and the driver side door open.
tem Descrip-
tion"
WCS-17, "KEY
The warning chime sounds when the ignition WARNING
Key warning chime (Without intelligent
switch is in OFF or ACC position with the key BCM CHIME : Sys-
key system)
inserted and the driver side door open. tem Descrip-
tion"
WCS-19, "RE-
The reverse warning chime sounds when the VERSE WARN-
Reverse warning chime (For Hong
ignition switch is in ON position with the selec- BCM ING CHIME :
Kong)
tor lever in R position. System De-
scription"

Revision: 2012 July WCS-8 N17

 SYSTEM
< SYSTEM DESCRIPTION >
WARNING CHIME SYSTEM : Circuit Diagram INFOID:0000000006892697

A
TYPE A

WCS

P
JSNIA4785GB

Revision: 2012 July WCS-9 N17

 SYSTEM
< SYSTEM DESCRIPTION >
TYPE B

JSNIA4786GB

WARNING CHIME SYSTEM : Fail-Safe INFOID:0000000006895587

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Function Specifications
Buzzer The buzzer turns OFF by suspending communication.

Revision: 2012 July WCS-10 N17

 SYSTEM
< SYSTEM DESCRIPTION >
PARKING BRAKE RELEASE WARNING CHIME
A
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000006655870

SYSTEM DIAGRAM B
Models With ABS

E
JSNIA2422GB

A/T Models Without ABS or CVT Models Without ABS

F

JSNIA2931GB
I
M/T Models Without ABS

L
JSNIA2932GB

WARNING OPERATION CONDITIONS

If all of the following conditions are fulfilled. M

Operation conditions
WCS
Ignition switch ON
Parking brake During the operation (parking brake switch ON)
Vehicle speed Approximately 7 km/h (4.3 MPH) or more O
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions are fulfilled.
P
Cancel conditions
Ignition switch Except ON
Parking brake Release condition (parking brake switch OFF)
Vehicle speed Approximately 3 km/h (1.9 MPH) or less

SIGNAL PATH

Revision: 2012 July WCS-11 N17

 SYSTEM
< SYSTEM DESCRIPTION >
Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.
MODELS WITH ABS

Signal name Signal path

Ignition switch signal —

Parking brake switch signal Parking brake switch Combination meter

Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter

A/T MODELS WITHOUT ABS OR CVT MODELS WITHOUT ABS

Signal name Signal path

Ignition switch signal —

Parking brake switch signal Parking brake switch Combination meter

Vehicle speed signal TCM Combination meter

M/T MODELS WITHOUT ABS

Signal name Signal path

Ignition switch signal —

Parking brake switch signal Parking brake switch Combination meter

Vehicle speed sensor signal Vehicle speed sensor Combination meter

TIMING CHART

JSNIA4040GB

SOUND SPECIFICATION

Revision: 2012 July WCS-12 N17

 SYSTEM
< SYSTEM DESCRIPTION >
TYPE A
A

JPNIA1775GB

TYPE B D

JSNIA3091GB G
NOTE:
To identify combination meter type, refer to WCS-3, "Information".
SEAT BELT REMINDER WARNING CHIME H

SEAT BELT REMINDER WARNING CHIME : System Description INFOID:0000000006892709

I
SYSTEM DIAGRAM (FOR CHINA AND AUSTRALIA)

L
JSNIA3824GB

SYSTEM DIAGRAM (FOR HONG KONG)

M

WCS

JSNIA3118GB

WARNING OPERATION CONDITIONS P

If all of the following conditions are fulfilled.

Operation conditions
Ignition switch ON

Revision: 2012 July WCS-13 N17

 SYSTEM
< SYSTEM DESCRIPTION >
Operation conditions
Driver seat belt Unfastened [seat belt buckle switch (driver side) ON]
Vehicle speed 15 km/h (9.3 MPH) or more

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled.

Operation conditions
Ignition switch Except ON
Driver seat belt Fastened [seat belt buckle switch (driver side) OFF]
90 seconds after the start of warning sound

SIGNAL PATH (FOR CHINA AND AUSTRALIA)

Combination meter sounds integrated buzzer when it judges that seat belt reminder warning chime is neces-
sary from signals below.

Signal name Signal source

Ignition switch signal —
Seat belt buckle switch signal
(driver side) Seat belt buckle switch (driver side) Combination meter

Vehicle speed signal ABS actuator and electric unit (control unit) Combination meter

SIGNAL PATH (FOR HONG KONG)

1. BCM requires warning chime output to combination meter when it judges seat belt warning chime is nec-
essary from signals below.

Signal name Signal path

Ignition switch signal —
Seat belt buckle switch signal
(driver side) Seat belt buckle switch (driver side) Combination meter BCM

Vehicle speed signal ABS actuator and electric unit (control unit) BCM

2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.

Signal name Signal path

Buzzer output signal BCM Combination meter

Revision: 2012 July WCS-14 N17

 SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART
A

JSNIA4041GB F
SOUND SPECIFICATION (FOR CHINA AND AUSTRALIA)
G

I
JSNIA2594GB

SOUND SPECIFICATION (FOR HONG KONG) J

JPNIA1772GB
M
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000006655872
WCS
SYSTEM DIAGRAM
O

JSNIA2421GB

WARNING CHIME OPERATION CONDITIONS

If all of the following conditions are fulfilled.

Revision: 2012 July WCS-15 N17

 SYSTEM
< SYSTEM DESCRIPTION >

Operation conditions
Ignition switch LOCK, OFF or ACC position
Combination switch (Lighting
1st or 2nd position
switch)
Driver door Open [front door switch (driver side) ON]

WARNING CHIME CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled.

Cancel conditions
Ignition switch ON
Combination switch (Lighting
OFF
switch)
Driver door Close [front door switch (driver side) OFF]

SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges light reminder warning chime is
necessary from signals below.

Signal name Signal source

Ignition switch signal —

Combination switch signal Combination switch (lighting switch) BCM

Driver door switch signal Front door switch (driver side) BCM

2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.

Signal name Signal source

Buzzer output signal BCM Combination meter

TIMING CHART

JSNIA4042GB

KEY WARNING CHIME

Revision: 2012 July WCS-16 N17

 SYSTEM
< SYSTEM DESCRIPTION >
KEY WARNING CHIME : System Description INFOID:0000000006655874

A
SYSTEM DIAGRAM

D
JSNIA2425GB

WARNING OPERATION CONDITIONS

E
If all of the following conditions are fulfilled.

Operation conditions
F
Ignition switch OFF or ACC position
Key switch ON (state that inserted key in key cylinder)
Driver door Open [front door switch (driver side) ON] G

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled. H

Cancel conditions
Ignition switch ON I
Key switch OFF (state that removed key from key cylinder)
Driver door Close [front door switch (driver side) OFF]
J
SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges key warning chime is necessary
from signals below. K

Signal name Signal source

Ignition switch signal — L

Key switch signal Key switch BCM

M
Driver door switch signal Front door switch (driver side) BCM

2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM. WCS

Signal name Signal source

O
Buzzer output signal BCM Combination meter

Revision: 2012 July WCS-17 N17

 SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART

JSNIA2429GB

SOUND SPECIFICATION
TYPE A

JPNIA1774GB

TYPE B

JSNIA3092GB

NOTE:
To identify combination meter type, refer to WCS-3, "Information".
REVERSE WARNING CHIME

Revision: 2012 July WCS-18 N17

 SYSTEM
< SYSTEM DESCRIPTION >
REVERSE WARNING CHIME : System Description INFOID:0000000008224217

A
SYSTEM DIAGRAM

D
JSNIA3827GB

WARNING CHIME OPERATION CONDITIONS

E
If all of the following conditions are fulfilled.

Operation conditions
F
Ignition switch ON
Shift position “R” position
G
WARNING CHIME CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
H
Cancel conditions
Ignition switch OFF
Shift position Other than “R” position I

SIGNAL PATH
1. BCM requires warning chime output to combination meter when it judges reverse warning chime is neces- J
sary from signals below.

Signal name Signal path

K
Ignition switch signal —

Shift position signal TCM Combination meter

L
2. Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.
M
Signal name Signal path

Buzzer output signal BCM Combination meter WCS

Revision: 2012 July WCS-19 N17

 SYSTEM
< SYSTEM DESCRIPTION >
TIMING CHART

JSNIA3826GB

SOUND SPECIFICATION

JPNIA1773GB

Revision: 2012 July WCS-20 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (COMBINATION METER)
A
TYPE A
TYPE A : CONSULT Function INFOID:0000000006895603
B
APPLICATION ITEMS
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.
C
System Diagnosis mode Description
Self Diagnostic Result The combination meter checks the conditions and displays memorized errors.
D
METER/M&A Data Monitor Displays the combination meter input/output data in real time.
W/L ON History Lighting history of the warning lamp and indicator lamp can be checked.

SELF DIAG RESULT E

Refer to MWI-35, "DTC Index".
DATA MONITOR
NOTE: F
The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
bleto this vehicle, refer to CONSULT display items.
G
Display Item List
X: Applicable

MAIN
Display item [Unit] Description H
SIGNALS
Value of vehicle speed signal received from ABS actuator and electric unit (control
SPEED METER unit) via CAN communication.
X I
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received.
Vehicle speed signal value transmitted to other units via CAN communication.
SPEED OUTPUT
[km/h]
X NOTE: J
655.35 is displayed when the malfunction signal is received.
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
K
Value of the engine speed signal received from ECM via CAN communication.
TACHO METER
X NOTE:
[rpm]
8191.875 is displayed when the malfunction signal is received.
L
FUEL METER
X Fuel level indicated on combination meter.
[L]
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication.
M
X
[°C] NOTE:
215 is displayed when the malfunction signal is input.
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received WCS
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
VDC/TCS IND
is received from ABS actuator and electric unit (control unit) via CAN communica- O
[On/Off]
tion.
SLIP IND Status of VDC warning lamp detected from VDC warning lamp signal received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
P
Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
NOTE:
[On/Off]
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L Status of door warning lamp detected from door switch signal received from BCM
[On/Off] via CAN communication.

Revision: 2012 July WCS-21 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS
HI-BEAM IND Status of high beam indicator lamp detected from high beam request signal is re-
[On/Off] ceived from BCM via CAN communication.
TURN IND Status of turn indicator lamp detected from turn indicator signal is received from
[On/Off] BCM via CAN communication.
FR FOG IND Status of front fog lamp indicator lamp detected from front fog light request signal
[On/Off] is received from BCM via CAN communication.
RR FOG IND Status of rear fog lamp indicator lamp detected from rear fog lamp status signal is
[On/Off] received from BCM via CAN communication.
LIGHT IND Status of tail lamp indicator lamp detected from position light request signal is re-
[On/Off] ceived from BCM via CAN communication.
• Status of oil pressure warning lamp detected from oil pressure warning lamp
signal is received from ECM via CAN communication. [HR15DE (for China)]
OIL W/L
• Status of oil pressure warning lamp detected from oil pressure switch signal is
[On/Off]
received from BCM via CAN communication. [HR12DE / K9K / HR15DE (Ex-
cept for China)]
MIL Status of malfunction indicator lamp (yellow) detected from malfunctioning indica-
[On/Off] tor lamp signal is received from ECM via CAN communication.
GLOW IND Status of glow indicator lamp detected from glow indicator lamp signal is received
[Off] from ECM via CAN communication.
C-ENG2 W/L Status of malfunction indicator lamp (red) detected from malfunction indicator
[Off] lamp signal is received from ECM via CAN communication.
CRUISE IND
This item is displayed, but cannot be monitored.
[Off]
O/D OFF IND Status of OD OFF indicator lamp detected from OD OFF indicator lamp signal is
[Off] received from TCM via CAN communication.
SPORT IND Status of SPORT indicator detected from sport mode switch signal is received
[On/Off] from CVT shift selector.
FUEL W/L
Low-fuel warning status detected by the identified fuel level.
[On/Off]
KEY G/Y W/L Status of KEY warning lamp (Green/Yellow) detected from KEY warning lamp sig-
[On/Off] nal is received from BCM via CAN communication.
KEY KNOB W/L
This item is displayed, but cannot be monitored.
[On/Off]
EPS W/L Status of EPS warning lamp detected from EPS warning lamp signal is received
[On/Off] from EPS control unit via CAN communication.
e-4WD W/L
This item is displayed, but cannot be monitored.
[Off]
CHAGE W/L
This item is displayed, but cannot be monitored.
[Off]
DPF W/L
This item is displayed, but cannot be monitored.
[Off]
FILTER W/L Status of water-in-fuel-filter warning lamp detected from water-in-fuel-filter warn-
[Off] ing lamp signal is received from ECM via CAN communication.
LCD Status of engine start operation indicator, shift P warning lamp and KEY warning
[B&P N, B&P I, C&P N, C&P I, LK lamp, detected from engine start operation indicator signal, shift P warning lamp
WN, ROTAT, SFT P, NO KY, ID NG, signal and KEY warning lamp signal are received from BCM via CAN communi-
BATT] cation.
SHIFT IND Status of shift position, detected from shift position signal received from TCM via
[P, R, N, D, L, 2, 1] CAN communication.
FUEL CAP W/L
This item is displayed, but cannot be monitored.
[Off]
O/D OFF SW
Status of SPORT mode switch.
[On/Off]

Revision: 2012 July WCS-22 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS A
REAR DEF SW
This item is displayed, but cannot be monitored.
[Off]
COMP F/B SIG A/C compressor activation condition that ECM judges according to the engine B
[On/Off] coolant temperature and the acceleration degree.
PKB SW
Status of parking brake switch.
[On/Off] C
BUCKLE SW
Status of seat belt buckle switch (driver side).
[On/Off]
BRAKE SW D
Status of stop lamp switch.
[Off]
BRAKE OIL SW
Status of brake fluid level switch.
[On/Off] E
A/C AMP CONN
Status of A/C auto amp. connection recognition signal.
[On/Off]
PASS BUCKLE SW F
This item is displayed, but cannot be monitored.
[Off]
DISTANCE
Value of distance to empty calculated by combination meter.
[km]
G
Ambient temperature value converted from ambient sensor signal received from
ambient sensor.
OUTSIDE TEMP NOTE:
[C° or F°] This may not match with the temperature value indicated on the information dis- H
play. (Because the information display value is a corrected value from the ambient
sensor input value.)
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit via CAN com- I
[On/Off] munication.
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition J
[On/Off]
of the combination meter.
AT STOP START IND Status of stop/start indicator lamp signal received from ECM via CAN communi-
[On, Off, BLINK1, BLINK2] cation.
K
AT STOP START STS
Status of stop/start readiness signal received from ECM via CAN communication.
[On/Off]
AT STOP START SW L
Status of stop/start indicator lamp.
[On/Off]
NOTE:
Some items are not available according to vehicle specification.
M
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on. WCS
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition. O
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts. P
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low.
Display Item

Revision: 2012 July WCS-23 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >

Display item Description

ABS W/L Lighting history of ABS warning lamp.
VDC/TCS IND Lighting history of VDC OFF indicator lamp.
SLIP IND Lighting history of VDC warning lamp.
BRAKE W/L Lighting history of brake warning lamp.
DOOR W/L Lighting history of door warning lamp.
OIL W/L Lighting history of oil pressure warning lamp.
C-ENG W/L Lighting history of malfunction indicator lamp (Yellow).
C-ENG2 W/L Lighting history of malfunction indicator lamp (Red).
O/D OFF IND Lighting history of OD OFF indicator lamp.
SPORT IND Lighting history of SPORT indicator lamp.
FUEL W/L Lighting history of low fuel level warning lamp.
KEY G/Y W/L Lighting history of KEY warning lamp (Green/Yellow).
EPS W/L Lighting history of EPS warning lamp.
NOTE:
In items displayed on the CONSULT screen, only those listed in the above table are used.
TYPE B
TYPE B : CONSULT Function INFOID:0000000007679428

APPLICATION ITEMS
CONSULT can perform the following diagnosis modes via CAN communication and the combination meter.

System Diagnosis mode Description

Self Diagnostic Result The combination meter checks the conditions and displays memorized errors.
METER/M&A Data Monitor Displays the combination meter input/output data in real time.
W/L ON History Lighting history of the warning lamp and indicator lamp can be checked.

SELF DIAG RESULT

Refer to MWI-95, "DTC Index".
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
bleto this vehicle, refer to CONSULT display items.
Display Item List
X: Applicable

MAIN
Display item [Unit] Description
SIGNALS
• Value of vehicle speed signal received from ABS actuator and electric unit (con-
trol unit) via CAN communication. (Models with ABS)
NOTE:
655.35 is displayed when the malfunction signal is received.
SPEED METER • Value of vehicle speed signal received from TCM via CAN communication. (A/
X
[km/h] T models without ABS or CVT models without ABS)
NOTE:
655.35 is displayed when the malfunction signal is received.
• Value of vehicle speed sensor signal received from vehicle speed sensor. (M/T
models without ABS)
Vehicle speed signal value transmitted to other units via CAN communication.
SPEED OUTPUT
X NOTE:
[km/h]
655.35 is displayed when the malfunction signal is received.

Revision: 2012 July WCS-24 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS A
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
Value of the engine speed signal received from ECM via CAN communication. B
TACHO METER
X NOTE:
[rpm]
8191.875 is displayed when the malfunction signal is received.
FUEL METER C
X Fuel level indicated on combination meter.
[L]
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication. D
X
[°C] NOTE:
215 is displayed when the malfunction signal is input.
INSTANT FUEL
Value of current fuel consumption calculated by combination meter. E
[km/L]
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of brake warning lamp detected from brake warning lamp signal is received
F
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
NOTE:
[On/Off]
Displays “Off” if the brake warning lamp is illuminated when the valve check starts, G
the parking brake switch is turned ON or the brake fluid level switch is turned ON.
DOOR W/L Status of door warning detected from door switch signal received from BCM via
[On/Off] CAN communication.
H
HI-BEAM IND Status of high beam indicator lamp detected from high beam request signal is re-
[On/Off] ceived from BCM via CAN communication.
TURN IND Status of turn indicator lamp detected from turn indicator signal is received from
I
[On/Off] BCM via CAN communication.
FR FOG IND Status of front fog lamp indicator lamp detected from front fog light request signal
[On/Off] is received from BCM via CAN communication.
J
RR FOG IND Status of rear fog lamp indicator lamp detected from rear fog lamp status signal is
[On/Off] received from BCM via CAN communication.
• Status of oil pressure warning lamp detected from oil pressure warning lamp
signal is received from ECM via CAN communication. [HR15DE (for China)] K
OIL W/L
• Status of oil pressure warning lamp detected from oil pressure switch signal is
[On/Off]
received from BCM via CAN communication. [HR12DE / K9K / HR15DE (Ex-
cept for China)] L
MIL Status of malfunction indicator lamp (yellow) detected from malfunctioning indica-
[On/Off] tor lamp signal is received from ECM via CAN communication.
C-ENG2 W/L Status of malfunction indicator lamp (red) detected from malfunction indicator M
[On/Off] lamp signal is received from ECM via CAN communication.
GLOW IND Status of glow indicator lamp detected from glow indicator lamp signal is received
[On/Off] from ECM via CAN communication.
WCS
CRUISE IND
This item is displayed, but cannot be monitored.
[Off]
O/D OFF IND Status of OD OFF indicator lamp detected from OD OFF indicator lamp signal is O
[On/Off] received from TCM via CAN communication.
SPORT IND Status of SPORT indicator detected from sport mode switch signal is received
[On/Off] from CVT shift selector.
P
FUEL W/L
Low-fuel warning status detected by the identified fuel level.
[On/Off]
KEY G/Y W/L
This item is displayed, but cannot be monitored.
[Off]
EPS W/L Status of EPS warning lamp detected from EPS warning lamp signal is received
[On/Off] from EPS control unit via CAN communication.

Revision: 2012 July WCS-25 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
MAIN
Display item [Unit] Description
SIGNALS
e-4WD W/L
This item is displayed, but cannot be monitored.
[Off]
DPF W/L
This item is displayed, but cannot be monitored.
[Off]
FILTER W/L Status of water-in-fuel-filter warning lamp detected from water-in-fuel-filter warn-
[On/Off] ing lamp signal is received from ECM via CAN communication.
LCD
This item is displayed, but cannot be monitored.
[Off]
SHIFT IND Status of shift position, detected from shift position signal received from TCM via
[P, R, N, D, L, 2, 1] CAN communication.
O/D OFF SW
Status of SPORT mode switch.
[On/Off]
REAR DEF SW
This item is displayed, but cannot be monitored.
[Off]
COMP F/B SIG
This item is displayed, but cannot be monitored.
[Off]
PKB SW
Status of parking brake switch.
[On/Off]
BUCKLE SW
Status of seat belt buckle switch (driver side).
[On/Off]
BRAKE SW
Status of stop lamp switch.
[On/Off]
BRAKE OIL SW
Status of brake fluid level switch.
[On/Off]
A/C AMP CONN
This item is displayed, but cannot be monitored.
[Off]
PASS BUCKLE SW
This item is displayed, but cannot be monitored.
[Off]
DISTANCE
Value of distance to empty calculated by combination meter.
[km]
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit via CAN com-
[On/Off] munication.
Buzzer status (in the combination meter) is detected from the buzzer output signal
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off]
of the combination meter.
AT STOP START IND Status of Stop/start indicator lamp signal received from ECM via CAN communi-
[On, Off, BLINK1, BLINK2] cation.
AT STOP START STS
Status of stop/start readiness signal received from ECM via CAN communication.
[On/Off]
AT STOP START SW
Status of Stop/start indicator lamp.
[On/Off]
NOTE:
Some items are not available according to vehicle specification.

W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine
and waiting for 30 seconds.
- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.

Revision: 2012 July WCS-26 N17

 DIAGNOSIS SYSTEM (COMBINATION METER)
< SYSTEM DESCRIPTION >
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets
low. A
Display Item

Display item Description B

ABS W/L Lighting history of ABS warning lamp.
BRAKE W/L Lighting history of brake warning lamp.
C
DOOR W/L Lighting history of door warning lamp.
OIL W/L Lighting history of oil pressure warning lamp.
C-ENG W/L Lighting history of malfunction indicator lamp (Yellow). D
C-ENG2 W/L Lighting history of malfunction indicator lamp (Red).
O/D OFF IND Lighting history of OD OFF indicator lamp.
E
SPORT IND Lighting history of SPORT indicator lamp.
FUEL W/L Lighting history of low fuel level warning lamp.
EPS W/L Lighting history of EPS warning lamp. F
NOTE:
In items displayed on the CONSULT screen, only those listed in the above table are used.
G

WCS

Revision: 2012 July WCS-27 N17

 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000007069475

APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.

Diagnosis mode Function Description

Work Support Changes the setting for each system function.
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER × × ×
Turn signal and hazard warning lamps FLASHER × × ×
• Automatic air conditioner
AIR CONDITONER ×
• Manual air conditioner
• Intelligent Key system
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
Body control system BCM ×
NATS IMMU × × ×
Interior room lamp battery saver BATTERY SAVER × × ×
Trunk lid open TRUNK ×
Theft warning alarm THEFT ALM × × ×
— RETAINED PWR* ×
Signal buffer system SIGNAL BUFFER × ×

*: This item is displayed, but is not used.

FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.

Revision: 2012 July WCS-28 N17

 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >

CONSULT screen item Indication/Unit Description A

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
B
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF C
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
D
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN E
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
F
ACC>OFF Power supply position While turning power supply position from “ACC” to “OFF”
status of the moment a
Vehicle Condition OFF>LOCK While turning power supply position from “OFF” to “LOCK”
particular DTC is de-
OFF>ACC tected* While turning power supply position from “OFF” to “ACC” G
ON>CRANK While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode H
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
LOCK Power supply position is “LOCK”. I
OFF Power supply position is “OFF”.
ACC Power supply position is “ACC”.
J
ON Power supply position is “IGN”
ENGINE RUN Power supply position is “RUN”.
CRANKING Power supply position is “CRANKING”. K
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition L
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
NOTE:
M
*: Refer to the following fir details at the power supply position.
• LOCK: Ignition switch OFF with steering is locked.
• OFF: Ignition switch OFF with steering is unlocked.
WCS
• ACC: Ignition switch ACC
• IGN: Ignition switch ON with engine stopped
• RUN: Ignition switch ON with engine running
O
• CRANKING: At engine cranking
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER) INFOID:0000000006655877 P

APPLICATION ITEMS

Test item Diagnosis mode Description

Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them.

Revision: 2012 July WCS-29 N17

 DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DATA MONITOR

Display item
Description
[Unit]
PUSH SW
Status of push-button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off]
VEH SPEED 1
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[On/Off]
CDL LOCK SW
Status of door lock unlock switch judged by BCM.
[On/Off]

ACTIVE TEST

Display item
Description
[Unit]
The seat belt reminder warning chime operation can be checked by operating the relevant function (On/
SEAT BELT WARN TEST
Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).

Revision: 2012 July WCS-30 N17

 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
A
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM) INFOID:0000000007069476
B
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor Monitors the reception status of CAN communication viewed from BCM.
Data Monitor The BCM input/output signals are displayed. E
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed.
• Read and save the vehicle specification. F
Configuration
• Write the vehicle specification when replacing BCM.

SYSTEM APPLICATION
G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×: Applicable item H
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test
I
Door lock DOOR LOCK × ×
Rear window defogger REAR DEFOGGER × ×
Warning chime BUZZER × × J
Interior room lamp control INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT × × ×
Exterior lamp HEAD LAMP × × ×
K

Wiper and washer WIPER × × ×

Turn signal and hazard warning lamps FLASHER × × L
• Automatic air conditioning
AIR CONDITONER ×
• Manual air conditioning
Combination switch COMB SW × M
Body control system BCM ×
NATS IMMU ×
Interior room lamp battery saver BATTERY SAVER × ×
WCS

Trunk lid open TRUNK ×

Theft warning alarm THEFT ALM*1 × × O
— RETAINED PWR*2
Signal buffer system SIGNAL BUFFER × ×
P
Panic alarm PANIC ALARM ×

*1: For models without theft warning alarm this mode is not used.
*2: This item is displayed, but is not used.
BUZZER

Revision: 2012 July WCS-31 N17

 DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
< SYSTEM DESCRIPTION >
BUZZER : CONSULT Function (BCM - BUZZER) INFOID:0000000006655879

APPLICATION ITEMS

Test item Diagnosis mode Description

Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them.

DATA MONITOR

Display item
Description
[Unit]
IGN ON SW
Status of ignition switch judged by BCM.
[On/Off]
KEY ON SW
Status of key switch judged by BCM.
[On/Off]
DOOR SW-DR
Status of driver side door switch judged by BCM.
[km/h]
REVERSE SW CAN
This item is displayed, but cannot be monitored.
[On/Off]
TAIL LAMP SW
Status of lighting switch judged by BCM using the combination switch readout function.
[On/Off]
FR FOG SW
Status of front fog lamp switch judged by BCM using the combination switch readout function.
[On/Off]
BUCKLE SW Status of seatbelt buckle switch (driver side) received from combination meter with CAN communica-
[On/Off] tion line.
VEHICLE SPEED
Value of vehicle speed signal received from combination meter with CAN communication line.
[km/h]

ACTIVE TEST

Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off).
The seat belt reminder warning chime operation can be checked by operating the relevant function (On/
SEAT BELT WARN TEST
Off).
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).

Revision: 2012 July WCS-32 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
ECU DIAGNOSIS INFORMATION A
COMBINATION METER
TYPE A
B
TYPE A : Reference Value INFOID:0000000006895593

VALUES ON THE DIAGNOSIS TOOL C

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
bleto this vehicle, refer to CONSULT display items. D

Monitor Item Condition Value/Status

Input value of vehicle speed signal E
(CAN communication signal)
SPEED METER Ignition switch
While driving NOTE:
[km/h] ON
655.35 is displayed when the malfunc-
tion signal is received F
Output value of vehicle speed signal
(CAN communication signal)
SPEED OUTPUT Ignition switch
While driving NOTE:
[km/h] ON G
655.35 is displayed when the malfunc-
tion signal is received
Output value of odometer signal (CAN
ODO OUTPUT Ignition switch communication signal) H
—
[km/h or mph] ON Equivalent to odometer reading in
combination meter
Input value of engine speed signal I
(CAN communication signal)
TACHO METER Ignition switch
Engine running NOTE:
[rpm] ON
8191.875 is displayed when the mal-
function signal is received J
FUEL METER Ignition switch
— Input value of fuel level sensor signal
[L] ON
Input value of engine coolant tempera- K
ture signal (CAN communication sig-
W TEMP METER Ignition switch nal)
—
[°C] ON NOTE:
L
215 is displayed when the malfunction
signal is input
NOTE:
Ignition switch M
FUEL CAP W/L This item is displayed, but cannot be moni- Off
ON
tored.

Ignition switch ABS warning lamp ON On

ABS W/L WCS
ON ABS warning lamp OFF Off

Ignition switch VDC OFF indicator lamp ON On

VDC/TCS IND
ON VDC OFF indicator lamp OFF Off
O
Ignition switch VDC warning lamp ON On
SLIP IND
ON VDC warning lamp OFF Off
Brake warning lamp ON On* P
Ignition switch
BRAKE W/L
ON Brake warning lamp OFF Off

Ignition switch Door warning lamp ON On

DOOR W/L
ON Door warning lamp OFF Off

Ignition switch High-beam indicator lamp ON On

HI-BEAM IND
ON High-beam indicator lamp OFF Off

Revision: 2012 July WCS-33 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status

Ignition switch Turn signal indicator lamp ON On

TURN IND
ON Turn signal indicator lamp OFF Off

Ignition switch Front fog lamp indicator lamp ON On

FR FOG IND
ON Front fog lamp indicator lamp OFF Off

Ignition switch Rear fog lamp indicator lamp ON On

RR FOG IND
ON Rear fog lamp indicator lamp OFF Off

Ignition switch Tail lamp indicator lamp ON On

LIGHT IND
ON Tail lamp indicator lamp OFF Off

Ignition switch Oil pressure warning lamp ON On

OIL W/L
ON Oil pressure warning lamp OFF Off

Ignition switch Malfunction indicator lamp (yellow) ON On

MIL
ON Malfunction indicator lamp (yellow) OFF Off

Ignition switch Glow indicator lamp ON On

GLOW IND
ON Glow indicator lamp OFF Off

Ignition switch Malfunction indicator lamp (red) ON On

C-ENG2 W/L
ON Malfunction indicator lamp (red) OFF Off
Ignition switch This item is displayed, but cannot be moni-
CRUISE IND Off
ON tored.

Ignition switch OD OFF indicator lamp ON On

O/D OFF IND
ON OD OFF indicator lamp OFF Off

Ignition switch SPORT indicator lamp ON On

SPORT IND
ON SPORT indicator lamp OFF Off

Ignition switch Low fuel warning displayed On

FUEL W/L
ON Low fuel warning not displayed Off

Ignition switch KEY warning lamp (Green/Yellow) ON On

KEY G/Y W/L
ON KEY warning lamp (Green/Yellow) OFF Off
Ignition switch This item is displayed, but cannot be moni-
KEY KNOB W/L Off
ON tored.

Ignition switch EPS warning lamp ON On

EPS W/L
ON EPS warning lamp OFF Off
Ignition switch This item is displayed, but cannot be moni-
e-4WD W/L Off
ON tored.
Ignition switch This item is displayed, but cannot be moni-
CHAGE W/L Off
ON tored.
Ignition switch This item is displayed, but cannot be moni-
DPF W/L Off
ON tored.

Ignition switch Water-in-fuel-filter warning lamp ON On

FILTER W/L
ON Water-in-fuel-filter warning lamp OFF Off

Revision: 2012 July WCS-34 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
Ignition switch Engine start operation indicator ON (A/T
B&P N
LOCK or ACC models or CVT models)
Ignition switch Engine start operation indicator ON (A/T
B&P I B
ON models or CVT models)
Ignition switch Engine start operation indicator ON (M/T
C&P N
LOCK or ACC models)
Ignition switch Engine start operation indicator ON (M/T C
C&P I
ON models)
Ignition switch
ACC warning display LK WN
ON D
LCD
Ignition switch
Steering lock information display ROTAT
LOCK
Ignition switch E
Shift P warning lamp ON SFT P
LOCK
Ignition switch
KEY warning lamp blinking NO KY
ON F
Ignition switch
Key ID warning display ID NG
LOCK
Ignition switch G
Intelligent Key low battery warning display BATT
LOCK
Shift position indicator P display P
Shift position indicator R display R H
Shift position indicator N display N
Ignition switch
SHIFT IND Shift position indicator D display D
ON I
Shift position indicator L display L
Shift position indicator 2 display 2
Shift position indicator 1 display 1 J
Ignition switch While pressing the SPORT mode switch On
O/D OFF SW
ON Other than the above Off
K
Ignition switch This item is displayed, but cannot be moni-
REAR DEF SW Off
ON tored.

Ignition switch A/C compressor activation condition On

COMP F/B SIG L
ON A/C compressor deactivation condition Off

Ignition switch Parking brake switch ON On

PKB SW
ON Parking brake switch OFF Off M
Ignition switch Seat belt buckle switch (driver side) ON On
BUCKLE SW
ON Seat belt buckle switch (driver side) OFF Off
WCS
Ignition switch Brake pedal is depressed On
BRAKE SW
ON Other than the above Off

Ignition switch Brake fluid level switch ON On O

BRAKE OIL SW
ON Brake fluid level switch OFF Off
Other than the following On
Ignition switch P
A/C AMP CONN Receives A/C auto amp. connection recog-
ON Off
nition signal
Ignition switch This item is displayed, but cannot be moni-
PASS BUCKLE SW Off
ON tored.
DISTANCE Ignition switch Distance to empty calculated by com-
—
[km] ON bination meter.

Revision: 2012 July WCS-35 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
Input value of ambient sensor signal.
Ignition switch NOTE:
OUTSIDE TEMP —
ON This may not match the indicated value
on the information display.

Ignition switch When “Distance to empty” indicates “––––”. On

FUEL LOW SIG
ON Other than above. Off

Ignition switch Buzzer ON On

BUZZER
ON Buzzer OFF Off
Stop/start indicator lamp ON On
Stop/start indicator lamp OFF Off
Ignition switch Stop/start indicator lamp blinks at a slow
AT STOP START IND BLINK1
ON speed.
Stop/start indicator lamp blinks at a high
BLINK2
speed.

Ignition switch Stop/start system is ON. On

AT STOP START STS
ON Other than the above Off

Ignition switch Stop/start switch indicator turns ON. On

AT STOP START SW
ON Stop/start switch indicator turns OFF. Off
*: Displays “Off” if the brake warning lamp is illuminated when the valve check starts, the parking brake switch
is turned ON or the brake fluid level switch is turned ON.
NOTE:
Some items are not available according to vehicle specification.
TERMINAL LAYOUT

JSNIA0623ZZ

PHYSICAL VALUES

Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
1
— CAN-H — — — —
(L)
2
— CAN-L — — — —
(P)

Revision: 2012 July WCS-36 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE: B
The maximum voltage varies de-
pending on the specification
(destination unit).
C
3 Ignition Speedometer operated
Vehicle speed signal
(SB)*1 Ground Output switch [When vehicle speed is ap-
(2-pulse)
(L/B) *2 ON prox. 40 km/h (25 MPH)]
D

JSNIA0015GB
E
• For combination meter specifi-
cations, refer to MWI-17, "IN-
Ignition FORMATION DISPLAY :
6
Ground Fuel level sensor signal Input switch — System Description". F
(W)
ON • For fuel level sensor specifica-
tions, refer to MWI-48, "Com-
ponent Inspection".
G
Air bag warning lamp
Ignition 4V
7 ON
Ground Air bag signal Input switch
(V) Air bag warning lamp
ON 0V H
OFF

Ignition While pressing the SPORT

8 Overdrive control / SPORT 0V
Ground Input switch mode switch.
(P) mode switch signal
ON
I
Other than above. 5V
When driver seat belt is fas-
5V
9 Seat belt buckle switch sig- Engine tened.
Ground Input J
(V) nal (driver side) idling When driver seat belt is un-
0V
fastened.
Ignition Parking brake applied. 0V
10 K
Ground Parking brake switch signal Input switch
(SB) Parking brake released. 5V
ON

Ignition Brake fluid level is normal 5V

11 Brake fluid level switch sig- L
Ground Input switch Brake fluid level is less than
(BR) nal 0V
ON LOW level
Stop/start OFF switch indi-
Ignition 0V M
13 Stop/start OFF switch indi- cator ON
Ground Input switch
(L) cator signal Stop/start OFF switch indi-
ON 12 V
cator OFF
WCS
Ignition DEF switch ON 0V
14*3 Ground DEF position signal Input switch
(V) ON DEF switch OFF 12 V

15 Ignition
O
(L)*4 Ground ACC power supply Input switch — Battery voltage
(R)*5 ACC

Security indicator lamp ON 0V P

Ignition
18
Ground Security signal Input switch Security indicator lamp
(G) 12 V
OFF OFF

Revision: 2012 July WCS-37 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output

Ignition
19*3 Ground Ambient sensor signal Input switch
Changes depending to am-
(GR) bient temperature.
ON

JSNIA0014GB

Ignition
20*3 Ground Ambient sensor ground — switch — 0V
(P) ON
Ignition
21
Ground Ground — switch — 0V
(B/W)
ON
Ignition
22
Ground Ground — switch — 0V
(B)
ON
Ignition
23
Ground Ground — switch — 0V
(B)
ON
Ignition
24
Ground Fuel level sensor ground — switch — 0V
(GR)
ON
Ignition
27
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition
28
Ground Ignition signal Input switch — Battery voltage
(GR)
ON
Ignition Brake pedal is depressed 0V
30
Ground Stop lamp switch signal Input switch
(LG) Other than the above Battery voltage
OFF
Ignition
31*3 Ground
A/C auto amp. connection
Input switch — 5V
(L) recognition signal
ON
A/C compressor activation
Ignition 12 V
32*3 Compressor feedback sig- condition
Ground Output switch
(GR) nal A/C compressor deactiva-
ON 0V
tion condition

Revision: 2012 July WCS-38 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
B

Engine idling [Approximate- C

ly 20°C (68°F)]

Ignition D
35*3 Ground
Engine coolant tempera-
Output switch
PKID0590E

(G) ture signal

ON

E
Engine idling [Approximate-
ly 80°C (176°F)]

F
SKIB3651J

Ignition Charge warning lamp ON 1.8 V

38 G
Ground Alternator signal Input switch
(Y) Charge warning lamp OFF 12 V
ON
*1: Except for Thailand and Hong Kong
*2: For Thailand and Hong Kong H
*3: With Auto A/C
*4: For China
*5: Except for China I
TYPE A : Fail-Safe INFOID:0000000006890233

The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning. J

Function Specifications
Buzzer The buzzer turns OFF by suspending communication. K

TYPE A : DTC Index INFOID:0000000006895594

L
Display contents of CONSULT Diagnostic item is detected when... Refer to
MWI-41,
CAN COMM CIRCUIT When combination meter is not transmitting or receiving CAN communication signal M
"Diagnosis
[U1000] for 2 seconds or more.
Procedure"
MWI-42,
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of the CAN controller of combina-
[U1010] tion meter.
"Diagnosis WCS
Procedure"
MWI-43,
VEHICLE SPEED The abnormal vehicle speed signal is input from the ABS actuator and electric unit
"Diagnosis O
[B2205] (control unit) for 2 seconds or more.
Procedure"
MWI-44,
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 seconds or
"Diagnosis
[B2267] more. P
Procedure"
MWI-45,
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature signals for 60
"Diagnosis
[B2268] seconds or more.
Procedure"

TYPE B

Revision: 2012 July WCS-39 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
TYPE B : Reference Value INFOID:0000000006895595

VALUES ON THE DIAGNOSIS TOOL

NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applica-
bleto this vehicle, refer to CONSULT display items.

Monitor Item Condition Value/Status

• Input value of vehicle speed signal
(CAN communication signal) (Mod-
els with ABS, A/T models without
ABS, or CVT models without ABS)
SPEED METER Ignition switch
While driving NOTE:
[km/h] ON
655.35 is displayed when the mal-
function signal is received
• Input value of vehicle speed sensor
signal (M/T models without ABS)
Output value of vehicle speed signal
(CAN communication signal)
SPEED OUTPUT Ignition switch
While driving NOTE:
[km/h] ON
655.35 is displayed when the malfunc-
tion signal is received
Output value of odometer signal (CAN
ODO OUTPUT Ignition switch communication signal)
—
[km/h or mph] ON Equivalent to odometer reading in
combination meter
Input value of engine speed signal
(CAN communication signal)
TACHO METER Ignition switch
Engine running NOTE:
[rpm] ON
8191.875 is displayed when the mal-
function signal is received
FUEL METER Ignition switch
— Input value of fuel level sensor signal
[L] ON
Input value of engine coolant tempera-
ture signal (CAN communication sig-
W TEMP METER Ignition switch nal)
—
[°C] ON NOTE:
215 is displayed when the malfunction
signal is input
Ignition switch Current fuel consumption calculated
INSTANT FUEL —
ON by combination meter.

Ignition switch ABS warning lamp ON On

ABS W/L
ON ABS warning lamp OFF Off

Ignition switch Brake warning lamp ON On*

BRAKE W/L
ON Brake warning lamp OFF Off

Ignition switch Door warning lamp ON On

DOOR W/L
ON Door warning lamp OFF Off

Ignition switch High-beam indicator lamp ON On

HI-BEAM IND
ON High-beam indicator lamp OFF Off

Ignition switch Turn signal indicator lamp ON On

TURN IND
ON Turn signal indicator lamp OFF Off

Ignition switch Front fog lamp indicator lamp ON On

FR FOG IND
ON Front fog lamp indicator lamp OFF Off

Ignition switch Rear fog lamp indicator lamp ON On

RR FOG IND
ON Rear fog lamp indicator lamp OFF Off

Revision: 2012 July WCS-40 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status
A
Ignition switch Oil pressure warning lamp ON On
OIL W/L
ON Oil pressure warning lamp OFF Off

Ignition switch Malfunction indicator lamp (yellow) ON On B

MIL
ON Malfunction indicator lamp (yellow) OFF Off

Ignition switch Glow indicator lamp ON On

GLOW IND
ON Glow indicator lamp OFF Off C

Ignition switch Malfunction indicator lamp (red) ON On

C-ENG2 W/L
ON Malfunction indicator lamp (red) OFF Off
D
Ignition switch This item is displayed, but cannot be moni-
CRUISE IND Off
ON tored.

Ignition switch OD OFF indicator lamp ON On E

O/D OFF IND
ON OD OFF indicator lamp OFF Off

Ignition switch SPORT indicator lamp ON On

SPORT IND
ON SPORT indicator lamp OFF Off F

Ignition switch Low fuel warning displayed On

FUEL W/L
ON Low fuel warning not displayed Off
G
Ignition switch This item is displayed, but cannot be moni-
KEY G/Y W/L Off
ON tored.

Ignition switch EPS warning lamp ON On H

EPS W/L
ON EPS warning lamp OFF Off
Ignition switch This item is displayed, but cannot be moni-
e-4WD W/L Off
ON tored. I
Ignition switch This item is displayed, but cannot be moni-
DPF W/L Off
ON tored.

Ignition switch Water-in-fuel-filter warning lamp ON On J

FILTER W/L
ON Water-in-fuel-filter warning lamp OFF Off
Ignition switch This item is displayed, but cannot be moni-
LCD Off K
LOCK or ACC tored.
Shift position indicator P display P
Shift position indicator R display R
L
Shift position indicator N display N
Ignition switch
SHIFT IND Shift position indicator D display D
ON
Shift position indicator L display L M
Shift position indicator 2 display 2
Shift position indicator 1 display 1
WCS
Ignition switch While pressing the SPORT mode switch On
O/D OFF SW
ON Other than the above Off
Ignition switch This item is displayed, but cannot be moni- O
REAR DEF SW Off
ON tored.
Ignition switch This item is displayed, but cannot be moni-
COMP F/B SIG Off
ON tored.
P
Ignition switch Parking brake switch ON On
PKB SW
ON Parking brake switch OFF Off

Ignition switch Seat belt buckle switch (driver side) ON On

BUCKLE SW
ON Seat belt buckle switch (driver side) OFF Off

Ignition switch Brake pedal is depressed On

BRAKE SW
ON Other than the above Off

Revision: 2012 July WCS-41 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Monitor Item Condition Value/Status

Ignition switch Brake fluid level switch ON On

BRAKE OIL SW
ON Brake fluid level switch OFF Off
Ignition switch This item is displayed, but cannot be moni-
A/C AMP CONN Off
ON tored.
Ignition switch This item is displayed, but cannot be moni-
PASS BUCKLE SW Off
ON tored.
DISTANCE Ignition switch Distance to empty calculated by com-
—
[km] ON bination meter.

Ignition switch When “Distance to empty” indicates “––––”. On

FUEL LOW SIG
ON Other than above. Off

Ignition switch Buzzer ON On

BUZZER
ON Buzzer OFF Off
Stop/start indicator lamp ON On
Stop/start indicator lamp OFF Off
Ignition switch Stop/start indicator lamp blinks at a slow
AT STOP START IND BLINK1
ON speed.
Stop/start indicator lamp blinks at a high
BLINK2
speed.

Ignition switch Stop/start system is ON. On

AT STOP START STS
ON Other than the above Off

Ignition switch Stop/start switch indicator turns ON. On

AT STOP START SW
ON Stop/start switch indicator turns OFF. Off
*: Displays “Off” if the brake warning lamp is illuminated when the valve check starts, the parking brake switch
is turned ON or the brake fluid level switch is turned ON.
NOTE:
Some items are not available according to vehicle specification.
TERMINAL LAYOUT

JPNIA0968GB

PHYSICAL VALUES

Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(R)
OFF
Ignition Brake pedal is depressed 0V
2
Ground Stop lamp switch signal Input switch
(LG) Other than the above Battery voltage
OFF
Ignition
3
Ground Ignition signal Input switch — Battery voltage
(GR)
ON

Revision: 2012 July WCS-42 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
• For combination meter specifi- B
cations, refer to MWI-78, "IN-
Ignition FORMATION DISPLAY :
4
Ground Fuel level sensor signal Input switch — System Description".
(W)
ON • For fuel level sensor specifica-
C
tions, refer to MWI-111, "Com-
ponent Inspection".
D

Speedometer operated
[When vehicle speed is ap- E
prox. 20 km/h (12.5 MPH)]

JSNIA3084ZZ F

G
Ignition Speedometer operated
6 25 Vehicle speed sensor sig-
Input switch [When vehicle speed is ap-
(L) (B) nal
ON prox. 40 km/h (25 MPH)]
H
JSNIA3085ZZ

Speedometer operated
[When vehicle speed is ap-
prox. 60 km/h (37.5 MPH)] J

JSNIA3086ZZ
K
Stop/start OFF switch indi-
Ignition 0V
7*2 Stop/start OFF switch indi- cator ON
Ground Input switch
(L) cator signal Stop/start OFF switch indi-
ON 12 V L
cator OFF
8
— CAN-H — — — —
(L)
M
Ignition DEF switch ON 0V
9*2 Ground DEF position signal Input switch
(V) ON DEF switch OFF 12 V

10 WCS
— CAN-L — — — —
(P)

Revision: 2012 July WCS-43 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output

Engine idling [Approximate-

ly 20°C (68°F)]

Ignition
14*1 Ground
Engine coolant tempera-
Output switch
PKID0590E

(G) ture signal

ON

Engine idling [Approximate-

ly 80°C (176°F)]

SKIB3651J

A/C compressor activation

Ignition 12 V
15*1 Compressor feedback sig- condition
Ground Output switch
(GR) nal A/C compressor deactiva-
ON 0V
tion condition
Ignition
21
Ground Ground — switch — 0V
(B)
ON
Ignition
22
Ground Ground — switch — 0V
(B)
ON
Ignition
23
Ground Ground — switch — 0V
(B/W)
ON
Ignition
26
Ground Fuel level sensor ground — switch — 0V
(GR)
ON

Ignition While pressing the SPORT

28 Overdrive control / SPORT 0V
Ground Input switch mode switch.
(P) mode switch signal
ON Other than the above 12 V
Ignition Security warning lamp ON 0V
31
Ground Security signal Input switch
(G) Security warning lamp OFF 12 V
OFF
Air bag warning lamp
Ignition 6V
32 ON
Ground Air bag signal Input switch
(V) Air bag warning lamp
ON 0V
OFF
When driver seat belt is fas-
Ignition 12 V
34 Seat belt buckle switch sig- tened.
Ground Input switch
(V) nal (driver side) When driver seat belt is un-
ON 0V
fastened.
Ignition Charge warning lamp ON 2V
35
Ground Alternator signal Input switch
(Y) Charge warning lamp OFF 12 V
ON

Ignition Brake fluid level is normal 12 V

36 Brake fluid level switch sig-
Ground Input switch Brake fluid level is less than
(BR) nal 0V
ON low level

Revision: 2012 July WCS-44 N17

 COMBINATION METER
< ECU DIAGNOSIS INFORMATION >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition Parking brake applied. 0V B
37
Ground Parking brake switch signal Input switch
(SB) Parking brake released. 12 V
ON
*1: With Auto A/C C
*2: With Stop / Start System
TYPE B : Fail-Safe INFOID:0000000006895598
D
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

Function Specifications E
Buzzer The buzzer turns OFF by suspending communication.

TYPE B : DTC Index INFOID:0000000006895597

F

Display contents of CONSULT Diagnostic item is detected when... Refer to

G
MWI-102,
CAN COMM CIRCUIT When combination meter is not transmitting or receiving CAN communication signal
"Diagnosis
[U1000] for 2 seconds or more.
Procedure"
MWI-103, H
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of the CAN controller of combina-
"Diagnosis
[U1010] tion meter.
Procedure"

VEHICLE SPEED The abnormal vehicle speed signal is input from the ABS actuator and electric unit
MWI-104, I
"Diagnosis
[B2205] (control unit) for 2 seconds or more.
Procedure"
MWI-105, J
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 seconds or
"Diagnosis
[B2267] more.
Procedure"
MWI-106,
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature signals for 60 K
"Diagnosis
[B2268] seconds or more.
Procedure"

WCS

Revision: 2012 July WCS-45 N17

 BCM (BODY CONTROL MODULE)
< ECU DIAGNOSIS INFORMATION >
BCM (BODY CONTROL MODULE)
List of ECU Reference INFOID:0000000006655883

ECU Reference
BCS-36, "Reference Value"
BCS-58, "Fail-safe"
With intelligent key system
BCS-60, "DTC Inspection Priority Chart"
BCS-61, "DTC Index"
BCM
BCS-115, "Reference Value"
BCS-129, "Fail-safe"
Without intelligent key system
BCS-130, "DTC Inspection Priority Chart"
BCS-130, "DTC Index"

Revision: 2012 July WCS-46 N17

 WARNING CHIME SYSTEM
< WIRING DIAGRAM >
WIRING DIAGRAM A
WARNING CHIME SYSTEM
TYPE A
B

WCS

Revision: 2012 July WCS-47 N17

 WARNING CHIME SYSTEM
< WIRING DIAGRAM >
TYPE A : Wiring Diagram - WITH ENGINE COOLANT TEMPERATURE GAUGE -
INFOID:0000000007030985

For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".

JRNWC1850GB

TYPE B

Revision: 2012 July WCS-48 N17

 WARNING CHIME SYSTEM
< WIRING DIAGRAM >
TYPE B : Wiring Diagram - WITHOUT ENGINE COOLANT TEMPERATURE GAUGE -
INFOID:0000000006655884 A

For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information".
B

WCS

JRNWC1851GB

Revision: 2012 July WCS-49 N17

 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow INFOID:0000000006655885

OVERALL SEQUENCE

JSNIA4485GB

DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.

>> GO TO 2.
2.CHECK SYMPTOM
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.

>> GO TO 3.
3.CHECK CONSULT SELF-DIAGNOSIS RESULTS

Revision: 2012 July WCS-50 N17

 DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
1. Connect CONSULT and perform self-diagnosis. Refer to WCS-39, "TYPE A : DTC Index" (TYPE A) or
WCS-45, "TYPE B : DTC Index" (TYPE B). A
2. When DTC is detected, follow the instructions below:
- Record DTC and Freeze Frame Data.
NOTE:
B
To identify combination meter type, refer to WCS-3, "Information".
Are self-diagnosis results normal?
YES >> GO TO 4.
C
NO >> GO TO 5.
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts. D

>> GO TO 5.
E
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE: F
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.

>> GO TO 6. G
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
H
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.
I

WCS

Revision: 2012 July WCS-51 N17

 POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
DTC/CIRCUIT DIAGNOSIS
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER (TYPE A)
COMBINATION METER (TYPE A) : Diagnosis Procedure INFOID:0000000006895915

1.CHECK FUSE
Check for blown fuses.

Power source Fuse No.

Battery 11

5*1
Ignition switch ON or START
64*2
Ignition switch ACC or ON 19
*1: Without Stop / Start System
*2: With Stop / Start System
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector and ground.

Terminals
(+) (−) Ignition switch po- Voltage
Combination meter sition (Approx.)

Connector Terminal
27 Ground OFF
M48 15 ACC Battery voltage
28 ON
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.

Combination meter
Continuity
Connector Terminal
21 Ground
M48 22 Existed
23
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
COMBINATION METER (TYPE B)

Revision: 2012 July WCS-52 N17

 POWER SUPPLY AND GROUND CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
COMBINATION METER (TYPE B) : Diagnosis Procedure INFOID:0000000006895916

A
1.CHECK FUSE
Check for blown fuses.
B
Power source Fuse No.
Battery 11
C
5*1
Ignition switch ON or START
64*2
*1: Without Stop / Start System D
*2: With Stop / Start System
Is the inspection result normal?
E
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT F
Check voltage between combination meter harness connector and ground.

Terminals G
(+) (−) Voltage
Ignition switch position
Combination meter (Approx.)
H
Connector Terminal
Ground
1 OFF
M49 Battery voltage
3 ON I
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse. J
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF. K
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector and ground.
L
Combination meter
Continuity
Connector Terminal
21 Ground M
M49 22 Existed
23
WCS
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
O

Revision: 2012 July WCS-53 N17

 METER BUZZER CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
METER BUZZER CIRCUIT
Component Function Check INFOID:0000000006655887

1.CHECK OPERATION OF METER BUZZER

1. Select “BUZZER” of “BCM” on CONSULT.
2. Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.

BUZZER
Under the condition of buzzer input : On
Except above : Off
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation".
NO >> Replace BCM. Refer to BCS-83, "Removal and Installation" (with Intelligent key system) or BCS-
147, "Removal and Installation" (without Intelligent key system).
Diagnosis Procedure INFOID:0000000006655888

1.CHECK POWER SUPPLY OF COMBINATION METER

Check power supply of combination meter. Refer to WCS-52, "COMBINATION METER (TYPE A) : Diagnosis
Procedure" (TYPE A) or WCS-53, "COMBINATION METER (TYPE B) : Diagnosis Procedure" (TYPE B).
NOTE:
To identify combination meter type, refer to WCS-3, "Information".
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair power supply circuit of combination meter.

Revision: 2012 July WCS-54 N17

 PARKING BRAKE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
PARKING BRAKE SWITCH SIGNAL CIRCUIT
A
TYPE A
TYPE A : Diagnosis Procedure INFOID:0000000006655889
B
1.CHECK COMBINATION METER INPUT SIGNAL
1. Turn ignition switch ON.
2. Check the voltage between combination meter harness connector and ground. C

(+) (−)
Voltage D
Combination meter Condition
(Approx.)
Connector Terminal
Ground
Ignition When parking brake is applied 0V E
M48 10
switch ON When parking brake is released 5V
Is the inspection result normal?
F
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT G
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking brake switch harness con- H
nector.

Terminals I
Combination meter Parking brake switch Continuity
Connector Terminal Connector Terminal
M48 10 M86 1 Existed J

4. Check continuity between combination meter harness connector and ground.

K
Terminals
Combination meter Continuity
Connector Terminal Ground L
M48 10 Not existed
Is the inspection result normal?
M
YES >> INSPECTION END
NO >> Repair harness or connector.
TYPE A : Component Inspection INFOID:0000000006655890 WCS

1.CHECK PARKING BRAKE SWITCH

Check parking brake switch. Refer to BRC-82, "Component Inspection". O
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace parking brake switch. Refer to PB-6, "Exploded View" (TYPE 1), PB-11, "Exploded View" P
(TYPE 2), PB-16, "Exploded View" (TYPE 3), or PB-21, "Exploded View" (TYPE 4).
TYPE B
TYPE B : Diagnosis Procedure INFOID:0000000006895885

1.CHECK COMBINATION METER INPUT SIGNAL

Revision: 2012 July WCS-55 N17

 PARKING BRAKE SWITCH SIGNAL CIRCUIT
< DTC/CIRCUIT DIAGNOSIS >
1. Turn ignition switch ON.
2. Check the voltage between combination meter harness connector and ground.

(+) (−)
Voltage
Combination meter Condition
(Approx.)
Connector Terminal
Ground
Ignition When parking brake is applied 0V
M49 37
switch ON When parking brake is released 12 V
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector and parking brake switch connector.
3. Check continuity between combination meter harness connector and parking brake switch harness con-
nector.

Terminals
Combination meter Parking brake switch Continuity
Connector Terminal Connector Terminal
M49 37 M86 1 Existed
4. Check continuity between combination meter harness connector and ground.

Terminals
Combination meter Continuity
Connector Terminal Ground
M49 37 Not existed
Is the inspection result normal?
YES >> INSPECTION END
NO >> Repair harness or connector.
TYPE B : Component Inspection INFOID:0000000006895886

1.CHECK PARKING BRAKE SWITCH

Check parking brake switch. Refer to BRC-82, "Component Inspection".
Is the inspection result normal?
YES >> INSPECTION END.
NO >> Replace parking brake switch. Refer to PB-6, "Exploded View" (TYPE 1), PB-11, "Exploded View"
(TYPE 2), PB-16, "Exploded View" (TYPE 3), or PB-21, "Exploded View" (TYPE 4).

Revision: 2012 July WCS-56 N17

 THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS A
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
B
Description INFOID:0000000006655891

• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is C
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
D
Diagnosis Procedure INFOID:0000000006655892

1.CHECK PARKING BRAKE WARNING LAMP E

1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
F
When parking brake is applied : ON
When parking brake is released : OFF
Is the inspection result normal? G
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation"
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT H

Perform check for the parking brake switch signal circuit. Refer to WCS-55, "TYPE A : Diagnosis Procedure"
(TYPE A) or WCS-55, "TYPE B : Diagnosis Procedure" (TYPE B).
I
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
J
3.CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to WCS-55, "TYPE A : Component Inspection" (TYPE
A) or WCS-56, "TYPE B : Component Inspection" (TYPE B). K
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation"
NO >> Replace parking brake switch. Refer to PB-6, "Exploded View" (TYPE 1), PB-11, "Exploded View" L
(TYPE 2), PB-16, "Exploded View" (TYPE 3), or PB-21, "Exploded View" (TYPE 4).
NOTE:
To identify combination meter type, refer to WCS-3, "Information". M

WCS

Revision: 2012 July WCS-57 N17

 THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
< SYMPTOM DIAGNOSIS >
THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
Description INFOID:0000000006892743

• Seat belt reminder warning does not sound.

• Seat belt reminder warning sounds continuously.
Diagnosis Procedure INFOID:0000000006892744

FOR CHINA AND AUSTRALIA

1.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check operation of seat belt warning lamp in combination meter.

Seat belt (driver side) fastened : OFF

Seat belt (driver side) unfastened : ON
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation" (TYPE A) or MWI-124,
"Removal and Installation" (TYPE B).
NO >> GO TO 2.
2.CHECK SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT (DRIVER SIDE)
Perform check for seat belt buckle switch (driver side) circuit. Refer to MWI-54, "Diagnosis Procedure" (TYPE
A) or MWI-115, "Diagnosis Procedure" (TYPE B).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform check for seat belt buckle switch (driver side). Refer to MWI-55, "Component Inspection" (TYPE A) or
MWI-116, "Component Inspection" (TYPE B).
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation" (TYPE A) or MWI-124,
"Removal and Installation" (TYPE B).
NO >> Replace seat belt buckle (driver side). Refer to SB-9, "SEAT BELT BUCKLE : Removal and Instal-
lation".
NOTE:
To identify combination meter type, refer to WCS-3, "Information".
FOR HONG KONG
1.CHECK SEAT BELT WARNING LAMP
1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.

Seat belt (driver side) fastened : OFF

Seat belt (driver side) unfastened : ON
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK BCM OUTPUT SIGNAL
Check if the seat belt warning chime is activated by performing BCM active test. Refer to WCS-29, "BUZZER :
CONSULT Function (BCM - BUZZER)" (WITH INTELLIGENT KEY SYSTEM) or WCS-32, "BUZZER : CON-
SULT Function (BCM - BUZZER)" (WITHOUT INTELLIGENT KEY SYSTEM).
Is the inspection result normal?

Revision: 2012 July WCS-58 N17

 THE SEAT BELT REMINDER WARNING CONTINUES SOUNDING, OR DOES
NOT SOUND
< SYMPTOM DIAGNOSIS >
YES >> INSPECTION END
NO >> GO TO 3. A
3.CHECK COMBINATION METER INPUT SIGNAL
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to WCS-21,
B
"TYPE A : CONSULT Function" (TYPE A) or WCS-24, "TYPE B : CONSULT Function" (TYPE B).

Buzzer active condition : On

Buzzer non-active condition : Off C
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation" (TYPE A) or MWI-124,
D
"Removal and Installation" (TYPE B).
NO >> Replace BCM. Refer to BCS-82, "Removal and Installation" (WITH INTELLIGENT KEY SYSTEM)
or BCS-147, "Removal and Installation" (WITHOUT INTELLIGENT KEY SYSTEM).
4.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE) CIRCUIT E

Perform the check for the seat belt buckle switch (driver side) circuit. Refer to MWI-54, "Diagnosis Procedure"
(TYPE A) or MWI-115, "Diagnosis Procedure" (TYPE B).
F
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair harness or connector. G
5.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to MWI-55, "Component Inspection"
(TYPE A) or MWI-116, "Component Inspection" (TYPE B). H
Is the inspection result normal?
YES >> Replace combination meter. Refer to MWI-63, "Removal and Installation" (TYPE A) or MWI-124,
"Removal and Installation" (TYPE B). I
NO >> Replace seat belt buckle (driver side). Refer to SB-9, "SEAT BELT BUCKLE : Removal and Instal-
lation".
NOTE: J
To identify combination meter type, refer to WCS-3, "Information".

WCS

Revision: 2012 July WCS-59 N17

 THE LIGHT REMINDER WARNING DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
THE LIGHT REMINDER WARNING DOES NOT SOUND
Description INFOID:0000000006655893

Light reminder warning chime does not sound even though headlamp is illuminated.
Diagnosis Procedure INFOID:0000000006655894

1.CHECK COMBINATION SWITCH (LIGHTING SWITCH) OPERATION

Check that the headlamps operate normally by operating the combination switch (lighting switch).
Do they operate normally?
YES >> GO TO 2.
NO >> Refer to EXL-72, "Symptom Table".
2.CHECK DRIVER SIDE DOOR SWITCH SIGNAL CIRCUIT
Perform the check for the driver side door switch signal circuit. Refer to DLK-84, "Diagnosis Procedure" (with
intelligent key system) or DLK-247, "Diagnosis Procedure" (without intelligent key system).
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair harness or connector.
3.CHECK DRIVER SIDE DOOR SWITCH
Perform a unit check for the driver side door switch. Refer to DLK-85, "Component Inspection" (with intelligent
key system) or DLK-248, "Component Inspection" (without intelligent key system).
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-82, "Removal and Installation" (with intelligent key system) or BCS-
147, "Removal and Installation" (without intelligent key system).
NO >> Replace driver side door switch. Refer to DLK-195, "Removal and Installation" (with intelligent key
system) or DLK-346, "Removal and Installation" (without intelligent key system).

Revision: 2012 July WCS-60 N17

 THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
< SYMPTOM DIAGNOSIS >
THE KEY WARNING DOES NOT SOUND (WITHOUT INTELLIGENT KEY)
A
Description INFOID:0000000006655895

The key warning chime does not sound, when all of the following conditions are fulfilled. B
• Key inserted into the key cylinder (key switch signal ON).
• Ignition switch is in ACC or OFF (ignition switch signal OFF).
• Driver side door is open (driver side door switch ON)
C
Diagnosis Procedure INFOID:0000000006655896

1.CHECK BCM INPUT SIGNAL D

1. Connect CONSULT.
2. Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY ON SW” monitor value. Refer to WCS-
29, "BUZZER : CONSULT Function (BCM - BUZZER)". E
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-82, "Removal and Installation" (with intelligent key system) or BCS-
147, "Removal and Installation" (without intelligent key system). F
NO >> GO TO 2.
2.CHECK KEY SWITCH SIGNAL CIRCUIT
Check the key switch signal circuit. Refer to DLK-252, "Diagnosis Procedure". G
Is the inspection result normal?
YES >> Replace BCM. Refer to BCS-82, "Removal and Installation" (with intelligent key system) or BCS-
147, "Removal and Installation" (without intelligent key system). H
NO >> Check applicable parts, and repair or replace corresponding parts.

WCS

Revision: 2012 July WCS-61 N17