PARTS LIST

ITEM QTY PART NO. PART DESCRIPTION LENGTH UNIT WT. NET WT.
1 4 P2174 2-3/8" OD X 174" SCH 40 GALVANIZED PIPE 174 in 55.75 222.98
2 2 P1126 1 1/4" X 126" SCH 40 PIPE (STIFF ARM) 126 in 25.12 50.23
16 X2
3 3 P2126 2-3/8" OD X 126" SCH 40 GALVANIZED PIPE 126 in 40.75 122.26
15 X2 4 4 P263 2-3/8" X 63"SCH 40 GALVANIZED PIPE 63 in 20.18 80.74
16 X2 5 3 X-232696 BALLAST TRAY WELDMENT - SITE PRO 1 66.53 199.60
14 X2 10
15 X2 6 2 X-RTP10 FRONT AND BACK HORIZONTAL TRAY SUPPORT WELDMENT 44.81 89.61
11 7 6 UNT10 UNISTRUT 120 in 20.38 122.27
14 X2
8 8 X-127594 FLAT DISK CLAMP PLATE 4" CENTERS (GALV.) 2.51 20.05
11 9 16 X-100064 CLAMP (4" V-CLAMP) GALVANIZED 0.91 14.61
10 14 SCX1 CROSSOVER PLATE 2-3/8" X 2-3/8" 6 in 3.71 51.92
1 11 56 X-UB1212 1/2" X 2-1/2" X 4-1/2" X 2" U-BOLT (HDG.) 0.63 35.01
12 32 G1204 1/2'' x 4" HDG HEX BOLT GR5 FULL THREAD 4 in 0.27 8.64
13 12 G1202 1/2'' x 2" HDG HEX BOLT GR5 2 in 0.18 2.11
14 156 G12FW 1/2" HDG USS FLATWASHER 3/32 in 0.03 5.32
15 156 G12LW 1/2" HDG LOCKWASHER 1/8 in 0.01 2.17
DETAIL A 16 156 G12NUT 1/2'' HDG HEAVY 2H HEX NUT 0.07 11.17
17 12 SS38R-8 3/8" X 8" THREADED ROD (STAINLESS STEEL) 0.25 3.01
18 24 SQW38 3/8" SQUARE WASHER 2 in 0.29 6.94
19 24 SS38LW 3/8" SS LOCKWASHER 0.01 0.16
20 24 SS38NUT 3/8" SS HEX NUT 0.02 0.44
TOTAL WT. # 1049.24
20 X2
3
16 X2
16 X2 19 X2
A 15 X2 16 16
9 18 X2
B 15 X2 10
14 X2 15 15
14 X2 17
11 14 14
3 11
12 12
7

C 16
16 X2 9
4 15
2 15 X2
8 14
14 X2
DETAIL C 12
DETAIL B 11
D DETAIL D
9

6 8
4

13 11
16
14 14 X2
15
15 15 X2
14
10
F 16 16 X2 9
E 5 12
DETAIL E DETAIL F
TOLERANCE NOTES DESCRIPTION
Locations:
New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 3 LEVEL Engineering Atlanta, GA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030") RRU / EQUIPMENT RACK Support Team: Los Angeles, CA
1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES FOR RTP FRAMES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

1 OF 3
ALL OTHER ASSEMBLY (± 0.060") CEK 4/23/2015 RTP10-3RRU

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
81 01 CUSTOMER BMC 4/24/2015 RTP10-3RRU
 120"

VARIABLE

TRIM ENDS
IF DESIRED

VARIABLE

60"

VARIABLE

VARIABLE

TOLERANCE NOTES DESCRIPTION

Locations:
New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 3 LEVEL Engineering Atlanta, GA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030") RRU / EQUIPMENT RACK Support Team: Los Angeles, CA
1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES FOR RTP FRAMES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

2 OF 3
ALL OTHER ASSEMBLY (± 0.060") CEK 4/23/2015 RTP10-3RRU

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
81 01 CUSTOMER BMC 4/24/2015 RTP10-3RRU
 WA
RTP FRAMES & RTP-RRU BALLAST EQUATIONS

BALLAST EQUATION WITH 1.5 SAFETY FACTOR:

AL (((AL*H1)+(EL*H2))1.5) - (WA*7.25)
FRONT WIND = WT =
3.625

(((AL*H1)+(-EL*H2))1.5) - (WRRU*7.25)
BACK WIND = WT =
3.625

BALLAST EQUATION WITH REV. G LOADING:

(((AL*H1)+(EL*H2))1.6) - (WA*7.25)
FRONT WIND = WT =
WRRU 3.625 (0.9)
H1
(((AL*H1)+(-EL*H2))1.6) - (WRRU*7.25)
BACK WIND = WT = 3.625 (0.9)

W = WT / 3
EL

WT
H2
EL = EQUIPMENT LOAD (NON-FACTORED) lbs
AL = ANTENNA LOAD (NON-FACTORED) lbs
H1 & H2 = HEIGHT FROM ROOFTOP ft
WT = TOTAL BALLAST WEIGHT lbs
W = BALLAST WEIGHT PER TRAY lbs
WRRU = 200 + EQUIPMENT WEIGHT lbs
WA = 260 + ANTENNA WEIGHT lbs

TOLERANCE NOTES DESCRIPTION

Locations:
New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: 3 LEVEL Engineering Atlanta, GA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030") RRU / EQUIPMENT RACK Support Team: Los Angeles, CA
1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES FOR RTP FRAMES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

3 OF 3
ALL OTHER ASSEMBLY (± 0.060") CEK 4/23/2015 RTP10-3RRU

PAGE
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
81 01 CUSTOMER BMC 4/24/2015 RTP10-3RRU