ACCELERATOR CONTROL SYSTEM

B ENGINE

ACC
SECTION
ACCELERATOR CONTROL SYSTEM C

E
CONTENTS
ACCELERATOR CONTROL SYSTEM ...................... 2 SERVICE DATA AND SPECIFICATIONS (SDS) ........ 3 F
Removal and Installation .......................................... 2 Tightening Torque ..................................................... 3
REMOVAL ............................................................. 2
INSTALLATION ..................................................... 2 G
INSPECTION AFTER INSTALLATION ................. 2

ACC-1
 ACCELERATOR CONTROL SYSTEM

ACCELERATOR CONTROL SYSTEM PFP:18005

Removal and Installation EBS00OJF

PBIC1506E

Accelerator pedal stopper

1. Accelerator pedal assembly 2.
(Underfloor carpet)

REMOVAL
1. Remove harness connector.
2. Remove mounting bolts, and remove accelerator assembly.
CAUTION:
● Do not disassemble accelerator pedal assembly and remove sensors.
● Handle them carefully without subjecting them to impacts such as dropping.
● Be careful not to get it wet.
3. Fold the floor carpet and remove accelerator pedal stopper.
● Remove pedal stopper by turning it counterclockwise with fingers.

INSTALLATION
Install in the reverse order of removal. be careful of the following:
● Insert locating pin into vehicle side to position accelerator pedal assembly. Install mounting bolt to acceler-
ator pedal assembly.
● Align the stud bolt on the floor with the thread hole to insert accelerator pedal stopper until it contacts the
face.
INSPECTION AFTER INSTALLATION
● Check that the accelerator pedal moves smoothly within the whole operation range.
● Check that the accelerator pedal securely returns to the original position.
● For the electrical inspection of the accelerator pedal assembly, refer to EC-213, "DTC P0226 APP SEN-
SOR" (WITH EURO-OBD), EC-548, "DTC P0226 APP SENSOR" (WITHOUT EURO-OBD).
● When accelerator electrical connector is disconnected, perform EC-34, "Accelerator Pedal Released
Position Learning" (WITH EURO-OBD), EC-435, "Accelerator Pedal Released Position Learning"
(WITHOUT EURO-OBD).

ACC-2
 SERVICE DATA AND SPECIFICATIONS (SDS)

SERVICE DATA AND SPECIFICATIONS (SDS) PFP:00030

A
Tightening Torque EBS00OJG

Unit: N·m (kg-m, in-lb)

Accelerator pedal assembly 4.3 - 5.9 (0.44 - 0.60, 38 - 52) ACC

ACC-3
SERVICE DATA AND SPECIFICATIONS (SDS)

ACC-4
AUTOMATIC TRANSAXLE

C TRANSMISSION/TRANSAXLE

B
SECTION
AUTOMATIC TRANSAXLE AT

E
CONTENTS
PRECAUTIONS .......................................................... 5 TROUBLE DIAGNOSIS — INTRODUCTION ........... 55 F
Precautions for Supplemental Restraint System Introduction ............................................................. 55
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN- Work Flow ............................................................... 59
SIONER” .................................................................. 5 TROUBLE DIAGNOSIS — BASIC INSPECTION ... 62 G
Precautions for On Board Diagnostic (EURO-OBD) A/T Fluid Check ...................................................... 62
System of A/T and Engine — Euro-OBD — ............. 5 Stall Test ................................................................. 63
Precautions for Trouble Diagnosis ........................... 5 Line Pressure Test .................................................. 66
H
Precautions for Harness Repair ............................... 5 Road Test ............................................................... 67
Precautions .............................................................. 6 TROUBLE DIAGNOSIS — GENERAL DESCRIP-
Service Notice or Precautions .................................. 7 TION .......................................................................... 84
Wiring Diagrams and Trouble Diagnosis .................. 8 Symptom Chart ....................................................... 84 I
PREPARATION ........................................................... 9 TCM Terminals and Reference Value ................... 105
Special Service Tools ............................................... 9 CAN COMMUNICATION ......................................... 108
Commercial Service Tools .......................................11 System Description ............................................... 108 J
A/T FLUID ................................................................. 12 DTC P0705 PARK/NEUTRAL POSITION (PNP)
Checking A/T Fluid ................................................. 12 SWITCH ...................................................................111
Changing A/T Fluid ................................................ 12 Description .............................................................111
K
OVERALL SYSTEM ................................................. 13 Wiring Diagram — AT — PNP/SW ....................... 113
A/T Electrical Parts Location .................................. 13 Diagnostic Procedure ........................................... 114
Circuit Diagram ...................................................... 14 Component Inspection .......................................... 116
Cross-Sectional View ............................................. 15 DTC P0710 A/T FLUID TEMPERATURE SENSOR L
Hydraulic Control Circuit ........................................ 16 CIRCUIT .................................................................. 117
Shift Mechanism ..................................................... 17 Description ............................................................ 117
Control System ....................................................... 26 Wiring Diagram — AT — FTS .............................. 119 M
Control Mechanism ................................................ 27 Diagnostic Procedure ........................................... 120
Control Valve .......................................................... 32 Component Inspection .......................................... 122
DTC P0720 VEHICLE SPEED SENSOR·A/T (REV-
EURO-OBD OLUTION SENSOR) ............................................... 123
Description ............................................................ 123
TROUBLE DIAGNOSIS — INDEX ........................... 33 Wiring Diagram — AT — VSSA/T ........................ 125
Alphabetical & P No. Index for DTC ....................... 33 Diagnostic Procedure ........................................... 126
ON BOARD DIAGNOSTIC SYSTEM DESCRIP- DTC P0725 ENGINE SPEED SIGNAL ................... 128
TION .......................................................................... 35 Description ............................................................ 128
Introduction ............................................................ 35 Wiring Diagram — AT — ENGSS ......................... 129
EURO-OBD Function for A/T System .................... 35 Diagnostic Procedure ........................................... 130
One or Two Trip Detection Logic of EURO-OBD ... 35 DTC P0731 A/T 1ST GEAR FUNCTION ................ 132
EURO-OBD Diagnostic Trouble Code (DTC) ......... 35 Description ............................................................ 132
Malfunction Indicator lamp (MIL) ............................ 39 Wiring Diagram — AT — 1ST ............................... 135
CONSULT-II ........................................................... 39 Diagnostic Procedure ........................................... 136
Diagnostic Procedure Without CONSULT-II ........... 49 Component Inspection .......................................... 137

AT-1
DTC P0732 A/T 2ND GEAR FUNCTION ................ 138 DTC VEHICLE SPEED SENSOR MTR ................... 199
Description ............................................................ 138 Description ............................................................ 199
Wiring Diagram — AT — 2ND .............................. 141 Wiring Diagram — AT — VSSMTR ....................... 201
Diagnostic Procedure ........................................... 142 Diagnostic Procedure ............................................ 202
Component Inspection .......................................... 143 DTC CONTROL UNIT (RAM), CONTROL UNIT
DTC P0733 A/T 3RD GEAR FUNCTION ................ 144 (ROM) ...................................................................... 203
Description ............................................................ 144 Description ............................................................ 203
Wiring Diagram — AT — 3RD .............................. 147 Diagnostic Procedure ............................................ 203
Diagnostic Procedure ........................................... 148 DTC CONTROL UNIT(EEPROM) ........................... 205
Component Inspection .......................................... 149 Description ............................................................ 205
DTC P0734 A/T 4TH GEAR FUNCTION ................ 150 Diagnostic Procedure ............................................ 206
Description ............................................................ 150 TROUBLE DIAGNOSES FOR SYMPTOMS ........... 207
Wiring Diagram — AT — 4TH ............................... 153 Wiring Diagram — AT — NONDTC ...................... 207
Diagnostic Procedure ........................................... 154 O/D OFF Indicator Lamp Does Not Come On ...... 209
Component Inspection .......................................... 157 Engine Cannot Be Started In “P” and “N” Position. 211
DTC P0740 TORQUE CONVERTER CLUTCH In “P” Position, Vehicle Moves Forward Or Back-
SOLENOID VALVE ................................................. 158 ward When Pushed ............................................... 212
Description ............................................................ 158 In “N” Position, Vehicle Moves .............................. 213
Wiring Diagram — AT — TCV .............................. 160 Large Shock. “N” → “R” Position .......................... 214
Diagnostic Procedure ........................................... 161 Vehicle Does Not Creep Backward In “R” Position.215
Component Inspection .......................................... 162 Vehicle Does Not Creep Forward In “D”, “2” Or “1”
DTC P0745 LINE PRESSURE SOLENOID VALVE. 163 Position ................................................................. 217
Description ............................................................ 163 Vehicle Cannot Be Started From D1 ..................... 219
Wiring Diagram — AT — LPSV ............................ 165 A/T Does Not Shift: D1 → D2 Or Does Not Kickdown:
Diagnostic Procedure ........................................... 166 D4 → D2 ................................................................ 222
Component Inspection .......................................... 168 A/T Does Not Shift: D2 → D3 ................................ 224
DTC P0750 SHIFT SOLENOID VALVE A ............... 170 A/T Does Not Shift: D3 → D4 ................................ 226
Description ............................................................ 170 A/T Does Not Perform Lock-up ............................. 229
Wiring Diagram — AT — SSV/A ........................... 172 A/T Does Not Hold Lock-up Condition .................. 230
Diagnostic Procedure ........................................... 173 Lock-up Is Not Released ....................................... 232
Component Inspection .......................................... 174 Engine Speed Does Not Return To Idle (Light Brak-
DTC P0755 SHIFT SOLENOID VALVE B ............... 175 ing D4 → D3 ) ........................................................ 233
Description ............................................................ 175 Vehicle Does Not Start From D1 ........................... 235
Wiring Diagram — AT — SSV/B ........................... 177 A/T Does Not Shift: D4 → D3 , When Overdrive Con-
Diagnostic Procedure ........................................... 178 trol Switch “ON” → “OFF” ..................................... 238
Component Inspection .......................................... 179 A/T Does Not Shift: D3 → 22 , When Selector Lever
DTC P1705 ACCELERATOR PEDAL POSITION “D” → “2” Position ................................................. 239
(APP) SENSOR ....................................................... 180 A/T Does Not Shift: 22 → 11 , When Selector Lever
Description ............................................................ 180 “2” → “1” Position .................................................. 240
Wiring Diagram — AT — TPS .............................. 182 Vehicle Does Not Decelerate By Engine Brake .... 242
Diagnostic Procedure ........................................... 183 TCM Self-diagnosis Does Not Activate ................. 244
DTC P1760 OVERRUN CLUTCH SOLENOID
VALVE ..................................................................... 185 EXC.F/EURO-OBD
Description ............................................................ 185
Wiring Diagram — AT — OVRCSV ...................... 187 ON BOARD DIAGNOSTIC SYSTEM DESCRIP-
Diagnostic Procedure ........................................... 188 TION ........................................................................ 248
Component Inspection .......................................... 189 CONSULT-II .......................................................... 248
DTC U1000 CAN COMMUNICATION LINE ............ 190 Diagnostic Procedure Without CONSULT-II ......... 254
Description ............................................................ 190 TROUBLE DIAGNOSIS — INTRODUCTION ......... 259
On Board Diagnosis Logic .................................... 190 Introduction ........................................................... 259
DTC Confirmation Procedure ............................... 190 Work Flow ............................................................. 263
Wiring Diagram — AT — CAN .............................. 191 TROUBLE DIAGNOSIS — BASIC INSPECTION ... 265
Diagnostic Procedure ........................................... 192 A/T Fluid Check .................................................... 265
DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP Stall Test ................................................................ 266
SENSOR CIRCUIT AND TCM POWER SOURCE). 193 Line Pressure Test ................................................ 269
Description ............................................................ 193 Road Test .............................................................. 270
Wiring Diagram — AT — BA/FTS ......................... 195 TROUBLE DIAGNOSIS — GENERAL DESCRIP-
Diagnostic Procedure ........................................... 196
Component Inspection .......................................... 198

AT-2
TION ........................................................................ 288 Wiring Diagram — AT — SSV/B ........................... 379
Symptom Chart .................................................... 288 Diagnostic Procedure ........................................... 380 A
TCM Terminals and Reference Value ................... 308 Component Inspection .......................................... 381
CAN COMMUNICATION .........................................311 OVERRUN CLUTCH SOLENOID VALVE ............... 382
System Description ...............................................311 Description ............................................................ 382 B
TROUBLE DIAGNOSES FOR SYMPTOMS .......... 314 Wiring Diagram — AT — OVRCSV ...................... 383
Wiring Diagram — AT — NONDTC ...................... 314 Diagnostic Procedure ........................................... 384
O/D OFF Indicator Lamp Does Not Come On ..... 316 Component Inspection .......................................... 384
Engine Cannot Be Started In “P” and “N” Position. 318 TORQUE CONVERTER CLUTCH SOLENOID AT
In “P” Position, Vehicle Moves Forward Or Back- VALVE ..................................................................... 386
ward When Pushed .............................................. 319 Description ............................................................ 386
In “N” Position, Vehicle Moves ............................. 320 Wiring Diagram — AT — TCV .............................. 388 D
Large Shock. “N” → “R” Position .......................... 321 Diagnostic Procedure ........................................... 389
Vehicle Does Not Creep Backward In “R” Position. 322 Component Inspection .......................................... 389
Vehicle Does Not Creep Forward In “D”, “2” Or “1” BATT/FLUID TEMP SEN (A/T FLUID TEMP SEN- E
Position ................................................................ 324 SOR CIRCUIT AND TCM POWER SOURCE) ....... 391
Vehicle Cannot Be Started From D1 ..................... 326 Description ............................................................ 391
A/T Does Not Shift: D1 → D2 Or Does Not Kick down: Wiring Diagram — AT — BA/FTS ......................... 393
D4 → D2 ............................................................... 329 Diagnostic Procedure ........................................... 394 F
A/T Does Not Shift: D2 → D3 ............................... 331 Component Inspection .......................................... 396
A/T Does Not Shift: D3 → D4 ............................... 333 ENGINE SPEED SIGNAL ....................................... 397
A/T Does Not Perform Lock-up ............................ 336 Description ............................................................ 397 G
A/T Does Not Hold Lock-up Condition ................. 337 Wiring Diagram — AT — ENGSS ......................... 398
Lock-up Is Not Released ...................................... 339 Diagnostic Procedure ........................................... 399
Engine Speed Does Not Return To Idle (Light Brak- LINE PRESSURE SOLENOID VALVE ................... 401 H
ing D4 → D3 ) ....................................................... 340 Description ............................................................ 401
Vehicle Does Not Start From D1 ........................... 342 Wiring Diagram — AT — LPSV ............................ 403
A/T Does Not Shift: D4 → D3 , When Overdrive Con- Diagnostic Procedure ........................................... 404
I
trol Switch “ON” → “OFF” ..................................... 345 Component Inspection .......................................... 406
A/T Does Not Shift: D3 → 22 , When Selector Lever CAN COMMUNICATION LINE ............................... 408
“D” → “2” Position ................................................ 346 Description ............................................................ 408
A/T Does Not Shift: 22 → 11 , When Selector Lever On Board Diagnosis Logic .................................... 408 J
“2” → “1” Position ................................................. 347 Self-Diagnosis Code Confirmation Procedure ...... 408
Vehicle Does Not Decelerate By Engine Brake ... 349 Wiring Diagram — AT — CAN .............................. 409
TCM Self-diagnosis Does Not Activate ................ 351 Diagnostic Procedure ........................................... 410 K
MAIN POWER SUPPLY AND GROUND CIRCUIT. 355
Wiring Diagram — AT — MAIN ............................ 355 ALL
Diagnostic Procedure ........................................... 356 L
VEHICLE SPEED SENSOR·A/T (REVOLUTION A/T SHIFT LOCK SYSTEM .................................... 411
SENSOR) ................................................................ 358 Description ............................................................ 411
Description ........................................................... 358 Shift Lock System Electrical Parts Location ......... 411
Wiring Diagram — AT — VSSA/T ........................ 360 Wiring Diagram — SHIFT — ................................ 412 M
Diagnostic Procedure ........................................... 361 Diagnostic Procedure ........................................... 413
DTC VEHICLE SPEED SENSOR MTR .................. 363 KEY INTERLOCK CABLE ...................................... 416
Description ........................................................... 363 Components ......................................................... 416
Wiring Diagram — AT — VSSMTR ...................... 365 Removal ............................................................... 416
Diagnostic Procedure ........................................... 366 Installation ............................................................ 417
ACCELE RATOR PEDAL POSITION (APP) SEN- ON-VEHICLE SERVICE .......................................... 419
SOR ........................................................................ 367 Control Valve Assembly and Accumulators .......... 419
Description ........................................................... 367 Control Cable Adjustment ..................................... 420
Wiring Diagram — AT — TPS .............................. 369 Park/Neutral Position (PNP) Switch Adjustment . 421
Diagnostic Procedure ........................................... 370 Differential Side Oil Seal Replacement ................ 421
SHIFT SOLENOID VALVE A .................................. 372 Revolution Sensor Replacement .......................... 422
Description ........................................................... 372 REMOVAL AND INSTALLATION ........................... 423
Wiring Diagram — AT — SSV/A .......................... 374 Removal ............................................................... 423
Diagnostic Procedure ........................................... 375 Installation ............................................................ 424
Component Inspection ......................................... 376 OVERHAUL ............................................................ 426
SHIFT SOLENOID VALVE B .................................. 377 Components ......................................................... 426
Description ........................................................... 377

AT-3
 Oil Channel ........................................................... 429 SERVICE DATA AND SPECIFICATIONS (SDS) .... 527
Locations of Adjusting Shims, Needle Bearings, General Specifications .......................................... 527
Thrust Washers and Snap Rings .......................... 430 Shift Schedule ....................................................... 527
DISASSEMBLY ....................................................... 431 Stall Revolution ..................................................... 528
Disassembly ......................................................... 431 Line Pressure ........................................................ 528
REPAIR FOR COMPONENT PARTS ...................... 443 Control Valves ....................................................... 528
Manual Shaft ........................................................ 443 Clutch and Brakes ................................................. 529
Oil Pump ............................................................... 446 Clutch and Brake Return Springs ......................... 530
Control Valve Assembly ........................................ 450 Oil Pump ............................................................... 531
Control Valve Upper Body .................................... 459 Input Shaft ............................................................. 531
Control Valve Lower Body .................................... 463 Planetary carrier .................................................... 531
Reverse Clutch ..................................................... 465 Final Drive ............................................................. 531
High Clutch ........................................................... 469 Reduction Pinion Gear .......................................... 532
Forward and Overrun Clutches ............................ 475 Output Shaft .......................................................... 534
Low & Reverse Brake ........................................... 482 Bearing Retainer ................................................... 535
Rear Internal Gear, Forward Clutch Hub and Over- Total End Play ....................................................... 535
run Clutch Hub ...................................................... 486 Reverse Clutch End Play ...................................... 535
Output Shaft, Idler Gear, Reduction Pinion Gear and Accumulator .......................................................... 536
Bearing Retainer ................................................... 490 Band Servo ........................................................... 536
Band Servo Piston Assembly ............................... 496 Removal and Installation ....................................... 536
Final Drive ............................................................ 501 Shift Solenoid Valves ............................................ 536
ASSEMBLY ............................................................. 506 Solenoid Valves .................................................... 536
Assembly (1) ......................................................... 506 A/T Fluid Temperature Sensor .............................. 536
Adjustment (1) ...................................................... 507 Revolution Sensor ................................................. 537
Assembly (2) ......................................................... 512 Dropping Resistor ................................................. 537
Adjustment (2) ...................................................... 516
Assembly (3) ......................................................... 520

AT-4
 PRECAUTIONS

PRECAUTIONS PFP:00001
A
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER” ECS008MZ

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual. AT
WARNING:
● To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. D
● Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. E
● Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harness connec-
tors. F
Precautions for On Board Diagnostic (EURO-OBD) System of A/T and Engine —
Euro-OBD — ECS008N0
G
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION: H
● Be sure to turn the ignition switch “OFF” and disconnect the negative battery terminal before any
repair or inspection work. The open/short circuit of related switches, sensors, solenoid valves,
etc. Will cause the MIL to light up.
I
● Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)
● Be sure to route and secure the harnesses properly after work. Interference of the harness with a J
bracket, etc. May cause the MIL to light up due to a short circuit.
● Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc. K
● Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.
L
Precautions for Trouble Diagnosis ECS008N1

CAN SYSTEM
● Do not apply voltage of 7.0V or higher to the measurement terminals. M
● Use the tester with its open terminal voltage being 7.0V or less.
Precautions for Harness Repair ECS008N2

CAN SYSTEM
● Solder the repaired parts, and wrap with tape. [Frays of twisted
line must be within 110 mm (4.33 in)]

PKIA0306E

AT-5
 PRECAUTIONS

● Do not perform bypass wire connections for the repair

parts.(The spliced wire will become separated and the charac-
teristics of twisted line will be lost.)

PKIA0307E

Precautions ECS008N3

● Before connecting or disconnecting the TCM harness con-

nector, turn ignition switch OFF and disconnect negative
battery terminal. Failure to do so may damage the TCM.
Because battery voltage is applied to TCM even if ignition
switch is turned off.

SEF289H

● When connecting or disconnecting pin connectors into or

from TCM, take care not to damage pin terminals (bend or
break).
Make sure that there are not any bends or breaks on TCM
pin terminal, when connecting pin connectors.

AAT470A

● Before replacing TCM, perform TCM input/output signal

inspection and make sure whether TCM functions properly
or not. (See page AT-105, "TCM Terminals and Reference
Value".)

MEF040DA

AT-6