Scribd
Upload
2 views

DLL!

Chapter 10 discusses error detection and correction in data transmission, highlighting the types of errors, redundancy, and coding techniques. It explains the concepts of single-bit and burst errors, as well as block coding, which involves adding redundant bits to datawords to create codewords for error detection and correction. The chapter also provides examples of how to detect and correct errors using coding schemes.

Uploaded by

nasim sayyad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
2 views

DLL!

Chapter 10 discusses error detection and correction in data transmission, highlighting the types of errors, redundancy, and coding techniques. It explains the concepts of single-bit and burst errors, as well as block coding, which involves adding redundant bits to datawords to create codewords for error detection and correction. The chapter also provides examples of how to detect and correct errors using coding schemes.

Uploaded by

nasim sayyad
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 25

Chapter 10

Error Detection
and
Correction

10.1 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.
Note

Data can be corrupted


during transmission.
Some applications require that
errors be detected and corrected.

10.2
10-1 INTRODUCTION

Let us first discuss some issues related, directly or


indirectly, to error detection and correction.

Topics discussed in this section:


Types of Errors
Redundancy
Detection Versus Correction
Forward Error Correction Versus Retransmission
Coding
Modular Arithmetic

10.3
Note

In a single-bit error, only 1 bit in the data


unit has changed.

10.4
Figure 10.1 Single-bit error

10.5
Note

A burst error means that 2 or more bits


in the data unit have changed.

10.6
Figure 10.2 Burst error of length 8

10.7
Note

To detect or correct errors, we need to


send extra (redundant) bits with data.

10.8
Figure 10.3 The structure of encoder and decoder

10.9
Note

In this book, we concentrate on block


codes; we leave convolution codes
to advanced texts.

10.10
Note

In modulo-N arithmetic, we use only the


integers in the range 0 to N −1,
inclusive.

10.11
Figure 10.4 XORing of two single bits or two words

10.12
10-2 BLOCK CODING

In block coding, we divide our message into blocks,


each of k bits, called datawords. We add r redundant
bits to each block to make the length n = k + r. The
resulting n-bit blocks are called codewords.

Topics discussed in this section:


Error Detection
Error Correction
Hamming Distance
Minimum Hamming Distance

10.13
Figure 10.5 Datawords and codewords in block coding

10.14
Example 10.1

The 4B/5B block coding discussed in Chapter 4 is a good


example of this type of coding. In this coding scheme,
k = 4 and n = 5. As we saw, we have 2k = 16 datawords
and 2n = 32 codewords. We saw that 16 out of 32
codewords are used for message transfer and the rest are
either used for other purposes or unused.

10.15
Error Detection

■ Enough redundancy is added to detect


an error.
■ The receiver knows an error occurred
but does not know which bit(s) is(are)
in error.
■ Has less overhead than error correction.

10.16
Figure 10.6 Process of error detection in block coding

10.17
Example 10.2

Let us assume that k = 2 and n = 3. Table 10.1 shows the


list of datawords and codewords. Later, we will see
how to derive a codeword from a dataword.

Assume the sender encodes the dataword 01 as 011 and


sends it to the receiver. Consider the following cases:

1. The receiver receives 011. It is a valid codeword. The


receiver extracts the dataword 01 from it.

10.18
Example 10.2 (continued)

2. The codeword is corrupted during transmission, and


111 is received. This is not a valid codeword and is
discarded.

3. The codeword is corrupted during transmission, and


000 is received. This is a valid codeword. The receiver
incorrectly extracts the dataword 00. Two corrupted
bits have made the error undetectable.

10.19
Table 10.1 A code for error detection (Example 10.2)

10.20
Note

An error-detecting code can detect


only the types of errors for which it is
designed; other types of errors may
remain undetected.

10.21
Figure 10.7 Structure of encoder and decoder in error correction

10.22
Example 10.3

Let us add more redundant bits to Example 10.2 to see if


the receiver can correct an error without knowing what
was actually sent. We add 3 redundant bits to the 2-bit
dataword to make 5-bit codewords. Table 10.2 shows the
datawords and codewords. Assume the dataword is 01.
The sender creates the codeword 01011. The codeword is
corrupted during transmission, and 01001 is received.
First, the receiver finds that the received codeword is not
in the table. This means an error has occurred. The
receiver, assuming that there is only 1 bit corrupted, uses
the following strategy to guess the correct dataword.

10.23
Example 10.3 (continued)
1. Comparing the received codeword with the first
codeword in the table (01001 versus 00000), the
receiver decides that the first codeword is not the one
that was sent because there are two different bits.

2. By the same reasoning, the original codeword cannot


be the third or fourth one in the table.

3. The original codeword must be the second one in the


table because this is the only one that differs from the
received codeword by 1 bit. The receiver replaces
01001 with 01011 and consults the table to find the
dataword 01.
10.24
Table 10.2 A code for error correction (Example 10.3)

10.25

You might also like