CS 7200

User and Installation Guide

Notice

The CS 7200 User Guide describes and illustrates the workflow for digital dental radiography using an
imaging plate (storage phosphor screen) for radiographic diagnostic intraoral images. We recommend that
you thoroughly familiarize yourself with this Guide in order to make the most effective use of your system.

Important:
 Read and follow the operating instructions in this guide carefully and always
keep it within easy reach.
 The room in which this unit is to be installed must comply with all official
applicable regulations.
 Improper use and handling can create hazards and cause damage to the unit.
 To prevent personal injury or material damage, you must observe all safety
information.
 Consult the CS 7200 Safety, Regulatory and the Technical Specifications User
Guide before using the CS 7200.

No part of this Guide may be reproduced without the express permission of Carestream Health, Inc.

U.S. Federal law restricts this device to sale by or on the order of a dentist or physician.

This document is originally written in English.

Manual Name: CS 7200 User and Installation Guide

Part Number: 6M0940
Revision Number: 04
Print Date: 2017-05

0086
Contents

Chapter 1 Conventions in this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Conventions in this
Guide

Chapter 2 Indications for Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

CS 7200 Overview Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CS 7200 Components Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Scanner Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Indication LEDs Statuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Imaging Plates Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Hygienic Sheaths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Chapter 3 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting Up CS 7200 Unit dimensions and Space Requirements . . . . . . . . . . . . . . . . . . . 9
Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Setting Up CS 7200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Connecting Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CS Imaging Software Installation . . . . . . . . . . . . . . . . . . . . . 13
CS 7200 Drivers Installation . . . . . . . . . . . . . . . . . . . . . . . . . 18
License Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
CS 7200 Post Installation Test. . . . . . . . . . . . . . . . . . . . . . . . 28
Adapt Filtering Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Access Adapt Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Create Customized Look. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Modify the Exisiting Customized Look . . . . . . . . . . . . . . . . 31
Delete Existing Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Chapter 4 General Software Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

CS Imaging Single Image Acquisition Overview. . . . . . . . . . . . . . . . . . . . 35
Software Overview Full Mouth Series (FMS) Image Acquisition Overview . . . 35
Patient Browser Window Overview . . . . . . . . . . . . . . . . . . . . 40

Chapter 5 Image Acquisition Workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Acquiring Images Acquiring Single Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Starting the Imaging Software . . . . . . . . . . . . . . . . . . . . . . . . 42
Preparing the Imaging Plates . . . . . . . . . . . . . . . . . . . . . . . . . 43
Performing the X-rays. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Scanning Imaging Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

CS 7200 User and Installation Guide (6M0940)_Ed04 i

 Acquiring Multiple Images. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Preparing the Acquisition of FMS Images . . . . . . . . . . . . . .50
Acquiring FMS Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
Retaking Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54
Manually Erasing the Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Changing Scanner User Preferences . . . . . . . . . . . . . . . . . . . . . . .57
Settings Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
Tools Tab. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
About Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
Changing Scan Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Chapter 6
Maintenance

Chapter 7 Quick Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

Troubleshooting Indication LEDs Statuses . . . . . . . . . . . . . . . . . . . . . . . . . . . .65

8 Offline License Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

Appendix Create a New Patient Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75

Chapter 9 Manufacturer’s Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Contact Information Authorized Representatives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

Chapter 10 List of Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81

List of Consumables

Chapter 11
Publications History

ii
1 Conventions in this Guide

Conventions in this Guide

The following special messages emphasize information or indicate potential risk to personnel or equipment:

WARNING: Warns you to avoid injury to yourself or others by following

the safety instructions precisely.

CAUTION: Alerts you to a condition that might cause serious damage.

Important: Alerts you to a condition that might cause problems.

Note: Emphasizes important information.

Tip: Provides extra information and hints.

CS 7200 User and Installation Guide (6M0940)_Ed04 1

2 Chapter 1 Conventions in this Guide
2 CS 7200 Overview

Indications for Use

The CS 7200 is intended for digital dental radiography using an imaging plates ( phosphor storage screens)
for dental intra-oral X-ray imaging.

Introduction

Note: The CS 7200 is intended for dental professionals. You are required to
have training to use the CS 7200.

The CS 7200 system is used to scan and review intraoral dental X-ray images. When scanning the X-ray
exposed imaging plate a digital image is displayed on the workstation screen. After scanning, the scanner
erases the imaging plate and ejects it. The imaging plate is ready for re-use.

The exam acquisition’s scanned image is sent to the Dental Imaging Software on the workstation. Using the
Dental Imaging Software, the image is processed and reviewed.

The system is composed of the following elements:

 CS 7200 scanning device (page 4)

 Imaging plates (page 7)

Note: The scanner is supplied with a separate viewing and archiving software
package: Dental Imaging Software, approved by Carestream Health.

Note: The CS 7200 User Guide is provided on the supplied CD/DVD-ROM.

CS 7200 User and Installation Guide (6M0940)_Ed04 3

CS 7200 Components Overview
Scanner Overview
The CS 7200 scanner includes the functions necessary for scanning and acquiring images from the imaging
plates.
Figure 1 CS 7200 Front View

On/Off switch
Turn scanner On: press for 1 second
Shut down the scanner:
1  press for 2 seconds to reset the scanner, run BIT.
The scanner remains turned on.

 press for 5 seconds to turn off the scanner.

2 Indication LEDs
3 Cover
4 Base
5 Intraoral imaging plates tray
6 Plate insertion entry
7 Plate size selection knob
8 Insertion panel.

4 Chapter 2 CS 7200 Overview

Figure 2 CS 7200 Back View

1 Base
2 Cables compartment
3 Cover

Figure 3 Cables Compartment in detail

1 Power supply inlet

2 USB port
3 Cable Compartment cove

CS 7200 User and Installation Guide (6M0940)_Ed04 5

Indication LEDs Statuses
The scanner LEDs status indicator shows the following scanner states:

LED Color Scanner State Remark

Off Off

Blinking Yellow Power up Blinking yellow

Yellow Stand by (door closed) Yellow

Type 1: Blinking yellow 1 - cable is disconnected

Type 2: Fast Blinking yellow - no driver
Yellow Disconnected
Type 3: Constant yellow: no UltraLite or scanner is
not ready

Plate is fully loaded. Take out

Blinking Cyan Beeps twice, sync with light,
envelope.

Green Insert plate (Door opened) Green

Green Load & recovery Green

If plate is not fully loaded for a number of times (three

Green Recovery consecutive attempts), the scanner performs a reset
and returns to loading position.

Green Ready for scan Green

Blinking Green Scanning

Fast Blinking Green Erasing/Eject

Blinking Red Error

6 Chapter 2 CS 7200 Overview

Imaging Plates Overview
The CS 7200 works with three imaging plate sizes: 0, 1 and 2. The scanned image file size depends on the
imaging plate size and the scanning resolution set by the user.

Table 2-1 Intraoral imaging plates sizes

Size Illustration Application

Periapical exam (Pediatric

0 dentistry)

Bitewing exam (Pediatric

1 dentistry)

2 Periapical exam (Adult)

The imaging plate has two sides: the active side for capturing the X-ray image and the inactive side. The
active side of the imaging plate includes an orientation ‘c’ mark with a dot inside to facilitate positioning
protocols within the patients’ mouth. The inactive side has a printed dot that corresponds to the location of
the orientation mark on the active side. This dot is visible through the transparent side of the hygienic sheath.

Active side

Inactive side

CS 7200 User and Installation Guide (6M0940)_Ed04 7

Hygienic Sheaths
For each imaging plate size, a one-time use, disposable, hygienic sheath is used for preventing cross
contamination. The transparent side allows you to see the dot, while the opaque side protects the active side
of the inserted imaging plate from image degradation.

Figure 4 Hygienic Sheath (front view)

1 Adhesive strip (for sealing the hygienic sheath)

2 Sheath transparent side to see the plate refernce
3 Tear line to be opened when inserting the plate into the scanner

8 Chapter 2 CS 7200 Overview

3 Setting Up CS 7200

Environmental Requirements
Check the following ambient operating condition requirements of the room, before installing the unit:

Temperature: 15–35 °C

Relative humidity: 30–85 % Non-condensing

Atmospheric pressure: 700–1060 hPa

For optimal results it is recommended that the light level in the room is approximately 500 lux (normal light
conditions) to minimize the imaging plates exposure to light.

Important: The scanner should be positioned so that there is always easy access
to the mains power supply socket.

Important: It is recommended not to install the scanner close to the opened

window to prevent the exposure to the direct sunlight.

Unit dimensions and Space Requirements

The scanner should be placed on a flat stable surface.

CS 7200 User & Installation Guide (6M0940)_Ed04 9

The unit dimensions illustrated in the above figure are as follows:

 Height of the unit 270 mm. (10.6 in.)

 Width 130 mm. (5.1 in.)

 Depth 300 mm. (11.8 in.)

Electrical Requirements
Table 2 Electrical installation specifications

Electrical Installation Specifications

Power Supply 100 V AC – 240 V AC, 0.8 - 0.4 A
Frequency 50/60 Hz
700 VA (UPS is connected to the
UPS (online, recommended) scanner, computer and monitor)
Minimum clearance between the 10 cm / 3.5 in.
table and the mains wall outlet

Minimum System Requirements

For installation of the CS 7200 intraoral imaging software, the computer must meet the minimum computer
system requirements, specified in the CS 7200 Safety, Regulatory & Technical Specification Guide. .

Important:
It is MANDATORY to check that the computer system configuration is
compatible with the computer minimum system requirements specified in the
Safety, Regulatory & Technical Specifications Guide. If necessary you must
update your computer system configuration.

10 Chapter 3 Setting Up CS 7200

Setting Up CS 7200
Connecting Cables
This chapter describes how to connect the Power Supply and USB cables to CS 7200:

Note: CS 7200 must be powered by the dedicates AC/DC adapter model

TR30RAM240, manufactured by Cincon Electronics Co., Ltd.

1. Install the power supply adaptor on power supply as shown below:

2. Remove the cable compartment cover.

CS 7200 User & Installation Guide (6M0940)_Ed04 11

3. Connect the Power supply cable to the power supply inlet in the cable compartment and route the cable
as shown on the below image to secure the cable in its place:

4. Connect the USB cable to the dedicated connector in the cable compartment, and route the cable as
shown on the below image to secure the cable in its place:

5. Close the cable compartment cover.

6. Connect the free end of the USB cable to the main USB port in the back of the computer.

7. Connect the Power Supply cable plug to the Mains wall socket.

12 Chapter 3 Setting Up CS 7200

CS Imaging Software Installation
This chapter describes the installation procedure of the Carestream Imaging Software (CSI).

NOTE:
Before installing CS Imaging Software check that:

 The computer meets the minimum computer system

requirements. See CS 7200 Safety, Regulatory &
Technical Specifications Guide.
 You have the two software DVD-ROMs: one for CS
Imaging Software and the other one for Scanner Driver
Software.
 The sleep mode in the computer is disabled.

To install the CSI software, follow these steps:

1 Insert the Carestream Imaging software DVD-ROM in the DVD-ROM drive of the PC.
The installation wizard is automatically loaded.

Note: If the installation wizard is not loaded, run the CSISuiteSetup 1.17 file
located on the installation DVD-ROM.

2 The Installer Language dialog box is displayed. Select the required language and click OK to
continue.

CS 7200 User & Installation Guide (6M0940)_Ed04 13

3 The Welcome screen is displayed. Click Next to continue.

4 The License Agreement screen is displayed. Click I Agree to continue the installation.

14 Chapter 3 Setting Up CS 7200

5 Click Browse to choose the location for the installation folder or leave the default location and click
Next.

6. Select the components to install and then click Install.

Patient file: is selected by default. You can deselect it, if you do not want the patient database.

7 The Practice Management Software Configuration screen is displayed. Click No.

CS 7200 User & Installation Guide (6M0940)_Ed04 15

 Click Yes only if you use Practice Management Software.

8 The Installing wizard screen is displayed. Let the installation process run automatically.

16 Chapter 3 Setting Up CS 7200

 The Installation Complete screen is displayed when the installation is finished.

9. Select Reboot now to complete the installation and then click Finish.

After the computer is restarted, proceed to “CS 7200 Drivers Installation” on page 18.

CS 7200 User & Installation Guide (6M0940)_Ed04 17

CS 7200 Drivers Installation
1 Insert the Scanner Driver Software DVD-ROM into the DVD-ROM drive.
2 Wait for the installation program to start.

Note: If the installation wizard is not loaded, run the wizard file located on the
installation DVD-ROM.

3. Select language from the list on the upper right side of the Installation Wizard window.

18 Chapter 3 Setting Up CS 7200

4. Click Run Installation Wizard to continue the installation.

5. Minimum system requirements are verified and the status of each checked item is displayed. Click Next
to continue the installation.

CS 7200 User & Installation Guide (6M0940)_Ed04 19

 Note: If a red X mark appears next to one of the items, click Help? to view the
description of the problem. Then, make sure your computer meets minimum
system requirements.

6. In the IP2 Image Acquisition window, click Install to install the required plug-ins on your computer.

20 Chapter 3 Setting Up CS 7200

7. The Welcome window is displayed. Click Next to continue the installation process.

8. The Destination Folder window is displayed. Click Next, if you accept the default destination folder or
browse to choose another destination folder, and then click Next.

CS 7200 User & Installation Guide (6M0940)_Ed04 21

9. Wait until the system installs the software.

10. The New Scanner Files window is displayed. Click Next to continue without updating the scanner
files.

22 Chapter 3 Setting Up CS 7200

11. The Installation Wizard Completed window is displayed. Click Finish to finish the installation.

12. On the Finish tab, click Finish to complete the installation.

13. Perform “License Activation” on page 24.

CS 7200 User & Installation Guide (6M0940)_Ed04 23

License Activation
After completing the installation, a license activation for the purchased scanner should be performed.

1. After the installation is complete, the license activation message appears:. Click Next to continue.

2. If the scanner is not connected and powered on, the following message appears:

3. Connect the scanner and turn it on.

24 Chapter 3 Setting Up CS 7200

4. The Login window appears. Enter your Carestream user name and password if you are a registered user.
If not, click Create a new user account and follow the link to the Carestream License Registration site.

5. On the Product Activation and Registration page, fill in the sign in details.

6. Select the product type, fill in the product details and click Register Product.

7. Click Continue to continue the registration process.

The verification code is sent to your email.

CS 7200 User & Installation Guide (6M0940)_Ed04 25

8. In the Email address verification section, enter the received verification code and click Continue.

9. In the Online License Activation window, enter the license key received with the scanner, select the
license check box and click Activate.

10. After the license activation process is complete, click Exit.

You are returned to the CS 7200 Installation Wizard.

26 Chapter 3 Setting Up CS 7200

11. Click Finish to finish the installation process.

CS 7200 User & Installation Guide (6M0940)_Ed04 27

CS 7200 Post Installation Test
After software and scanner installation, check that all scanner components are properly installed and the
scanned images are properly displayed in the CS Imaging Software.

1. Start the CS Imaging Software and select or create test patient. See “Starting the Imaging Software” on
page 42.

2. Expose a plate size 2 with a metal object (such as coin or key) on it.

3. Load the exposed plate into the scanner and wait until the scan is complete and the image is displayed
on the CS Imaging Software main screen. .

4. Close the CS Imaging Software main screen.

28 Chapter 3 Setting Up CS 7200

Adapt Filtering Options
The adapt filtering options enable user to choose the preferable look of the scanned image

Access Adapt Library

1. Click Modify favorite to change the preferable look that will be applied after the scan.

2. The gallery of the available looks is displayed at the bottom of the screen.

3. Click Apply at acquisition to apply this view during the image acquisition process.

4. Hover the mouse pointer over the selected frame in the gallery. The following options are available:

CS 7200 User & Installation Guide (6M0940)_Ed04 29

Action Description
Favorite Click to add the selected look to the favorites list.
Create Click to create a new look based on the selected look.
Modify Click to modify the selected look. The option is vailable
only for the looks created by user.
Delete Click to delete the selected look from the gallery. The
option is available only for the looks created by user.

Create Customized Look

To create and add a customized look to the favorites gallery, perform the following steps:

1. Select the frame to be customized.

2. Hover with the mouse pointer over the selected frame.

3. Click Create.

4. Adjust brightness and contrast of the new look by using Brightness and Contrast sliders.

Use the zoom slider to zoom in or out certain areas of the image.

30 Chapter 3 Setting Up CS 7200

 Choose either Navigation or Histogram view when adjusting the new look.

5. Click Create to create a new modified look and add it to the frames gallery.

Modify the Exisiting Customized Look

1. Select the frame to be customized.

2. Hover with the mouse pointer over the selelcted frame.

3. Click Modify.

4. Perform the required changes and click Save Changes.

CS 7200 User & Installation Guide (6M0940)_Ed04 31

5. If you close the CS Adapt Library screen without saving the performed actions,. the following dialog
box appears:

6. Click OK if you really want to exit without saving chnages or click Cancel to return to the CS Adapt
Library screen.

32 Chapter 3 Setting Up CS 7200

Delete Existing Filter
1. Select the frame to be customized.

2. Hover with the mouse pointer over the selelcted frame.

3. Click Delete.

4. In the Delete Filter dialog box that appears, click Yes to confirm the action.

CS 7200 User & Installation Guide (6M0940)_Ed04 33

34 Chapter 3 Setting Up CS 7200
4 CS Imaging Software Overview

General Software Overview

CS 7200 operates with the CS Imaging Software. You can acquire:

 Single images.
 Full Mouth Series (FMS).

Single Image Acquisition Overview

You can acquire individual images using the CS Imaging Software.

Figure 5 CS Imaging Software with Active CS 7200 Scanner Connected

Full Mouth Series (FMS) Image Acquisition Overview

The Full Mouth Series (FMS) is a static representation of the mouth of the patient using a series of intraoral
images. The images are placed in fixed numbered frames.

Figure 6 CS 7200 FMS Acquisition Interface Home Page

CS 7200 User and Installation Guide (6M0940)_Ed04 35

 1 Dental arch: Highlights the acquisition zone.

2 FMS template: Displays frame templates for acquisition.

 Green highlight: Frame ready for new acquisition
 Blue highlight: Frame in the revue and retake mode. This mode interrupts the automatic acquisition
sequence.

3 Preview screen: Displays the currently acquired image.

Figure 7 FMS Select a Format

Select a Format enables you to select FMS template options to select for acquisition. You can modify existing
templates and create new templates (see the Carestream Imaging Software Online Help).

Note: Only FMS templates for CR images can be used. Using other FMS will
cause images not to be displayed.

36 Chapter 4 CS Imaging Software Overview

Figure 8 Control Panel with CS Adapt Buttons

Control Panel: enables you to adjust the brightness and contrast of the image. For more information on
Control Panel functions, see the CS Imaging Software Online Help.

Optiview:Maps pure black to blue and pure white to green, leaving other shades
unchanged.

Negative: Displays the image as a photo negative.

Colors #1: Maps pure black to blue and pure white to red.

Colors #2: Maps middle-gray to orange and leaves pure white and pure black in their
original states.

CS Adapt Library: Opens the CS Adapt Library software that allows to manage your
filters.

Adapt - Unfiltered Perio: Enhances the display of periodontal tissue.

Adapt - Unfiltered Endo1: Enhances contrast at the canals and roots (produces brighter
images).

CS 7200 User and Installation Guide (6M0940)_Ed04 37

 Adapt - Unfiltered DEJ1: Optimizes contrast at crowns, amelo-dentinal junctions, and
roots (produces brighter images).

Adapt - OptimizedContrastEndo: Enhances contrast at the canals and roots.

Figure 9 Intraoral Toolbar

INTRA toolbar: enables you to adjust the image display. For more information on Intraoral toolbar
functions, see the Carestream Dental Imaging Software Online Help.

Sharpness filter: click to apply sharpnes filter on the image.

Highlight: click to optimize contrast within a region of interest.

Measurements: click to draw measuring lines on the image.

Flip: .click to rotate the image by 180o clockwise..

90o rotation:click to rotate the image by 90o clockwise.

Acquisition correction:click to create a mirror image of the original image.

38 Chapter 4 CS Imaging Software Overview

Edit annotations: click to open the image in an annotations editor.

Display annotations: click to display any annotations on the image. Click again to
hide the anotations.

Pseudo - 3D: click to display gray scale levels as height values.

Relief filter: click to enhabce the outlines of the shapes in an image by displaying the
image in relief mode.

Isodensity dots: click to apply color to pixels of the same bone density.

Densitometric analysis: click to analyze bone density.

Caries Detector: click to open the Logicon Caries module for detecting interproximal
caries.

CS 7200 User and Installation Guide (6M0940)_Ed04 39

Patient Browser Window Overview

A Title bar: name of the selected patient.

B System icons: About, Prefernces and Online Help.
C Imaging Software Button: click to open the Imaging Window.
D Patient Card:information on the selected patient..
E Image Management Tools: import/export and print functions.
F Patient History: displays the list of available patients.

G Patient List: displays the list of available patients.

H Patient Search: allows searching in the patient list.
I Patient Management Tools: contain create/modify patient functions.
J Patient History Tools: contain patient history functions.

40 Chapter 4 CS Imaging Software Overview

5 Acquiring Images

Image Acquisition Workflow

This chapter describes the acquisition procedure for acquiring dental images.

A typical workflow consists of the following steps:

1 Selecting or Creating a Patient Record and Accessing the imaging window. See “Starting the Imaging
Software” on page 42.
2 Inserting the Imaging Plate into a hygienic sheath and sealing it. See “Preparing the Imaging Plates” on
page 43.
3 Positioning, exposing and removing the imaging plate from the patient’s mouth . See “Performing the
X-rays” on page 44.
4 Disinfecting the Hygienic Sheath. Refer to the CS 7200 Safety and Regulatory Guide (6K9678).
5 Scanning the imaging plate and reviewing the image. See “Scanning Imaging Plate” on page 47.

CS 7200 User and Installation Guide (6M0940)_Ed04 41

Acquiring Single Image
Starting the Imaging Software
Open your Imaging Software.

1 On your desktop, double-click the CS Imaging Software icon or click Start > All Programs > ( the
name of your) Dental Imaging Software.

The Patient Browser window is displayed:

2 Create or open an existing patient record:

 To open an existing patient record: In the Patient Browser search field (H), start typing to search
for a patient card.

 To create a new patient record: Click the Create New Patient Card button alongside the search
field to create a new patient card. For more details, see “Create a New Patient Card” on page 75

The CS 7200 indication LED turns from yellow to green, indicating that the scanner is ready for use and
the Imaging Window appears.

3. Once you have selected or created a patient, in the Patient Browser Toolbar (C) click the arrow button to
open the Imaging application. The Patient Browser window remains open and the Imaging Window is
displayed.

42 Chapter 5 Acquiring Images

4. Wait for the Scanner Status icon to turn green on the Imaging Window toolbar indicating that the CS
7200 scanner is connected to the workstation and is ready for acquisition.

Preparing the Imaging Plates

To prepare the intraoral imaging plate, follow these steps:

1 Choose an imaging plate of the appropriate size for your examination.

Important: Use only CS 7200 intraoral imaging plates from Carestream

and hygienic sheaths from Carestream. The use of plates or hygienic
sheaths from a third party supplier may cause a malfunction of the
system and void the warranty.

Important: Use a NEW hygienic sheath for each new patient to prevent
cross contamination.

Important: Use a NEW hygienic sheath for each new image to prevent
humidity and contamination of the plate.

Tip: If the imaging plate has not been used for a while, proceed to erasing it
first. See “Manually Erasing the Plate” on page 56..

2 Insert the imaging plate into its protective hygienic sheath with the inactive side facing the adhesive
strip, so the imaging plate’s size number is seen through the transparent side of the hygienic sheath and
the orientation mark visible in the bottom corner (A).

CS 7200 User and Installation Guide (6M0940)_Ed04 43

3 Peel the adhesive strip’s protective paper to seal the hygienic sheath (B) and (C).

4 Handle the imaging plate by holding the hygienic sheath’s empty edge where the silicone strip is.
5. Select an appropriate positioner for the region of interest and the size of the plate.

Performing the X-rays

Perform the required X-rays according to your clinical procedure.

It is recommended to continue using X-ray positioning techniques and tools to ensure the resulting image is
complete and includes all the information required for diagnosis.To facilitate matching the orientation of the
image in the software to the clinical reality, we recommend to position the imaging plate in the mouth of the
patient with the orientation mark always towards the bottom.

44 Chapter 5 Acquiring Images

 Important: Make sure the active side of the imaging plate is facing the
X-ray tube.

1 Select the X-ray exposure time according to the region of interest and the patient type. Follow the user
instructions of your X-ray generator. The following tables provide guidelines for exposure times for an
X-ray generator at 70 kV and 7 mA. Add your values for the exposure time in seconds in the column on
the right.

Important: These are suggested exposure times and need to be adjusted

for your specific X-ray generator.

Tip: If images are too dark, reduce the exposure time. If images are too white
or look grainy, increase the exposure time.

Table 3 Exposure times

Parameter DC-emitter, 7mA, tube length 20 cm DC-emitter, 7mA, tube length 30 cm

recommended exposure time (s) recommended exposure time (s)
Upper jaw 60kV 70kV 60kV 70kV
incisors 0.1 0.08 0.2 0.16
pre-molars 0.125 0.1 0.25 0.2
molars 0.16 0.125 0.32 0.25
Lower jaw 60kV 70kV 60kV 70kV
incisors 0.1 0.08 0.2 0.16
pre-molars 0.125 0.1 0.25 0.2
molars 0.125 0.1 0.25 0.2
Bitewing 0.16 0.125 0.32 0.25

CS 7200 User and Installation Guide (6M0940)_Ed04 45

2. Position the CS 7200 imaging plate in the mouth of the patient depending on the region of interest.

3. Move the X-ray generator tube head close to the patient and align it with the tooth of the patient and the
CS 7200 imaging plate.

Important: Respect the X-ray techniques to avoid image distortion and

minimize magnification.

Important: Make sure that the tube head is not shaking.

Important: Perform the required X-rays according to your clinical

procedure.

4 Tell the patient to remain still without moving the tongue.

5. Position yourself either two meters behind the X-ray generator or outside the room.

Important: Make sure you can keep visual contact with the patient
during the X-ray.

6. Trigger the X-ray with the remote switch of the X-ray generator.

7. Remove the CS 7200 imaging plate from the mouth of the patient.

46 Chapter 5 Acquiring Images

8. Clean and disinfect the hygienic sheath after each patient (see the CS 7200 Safety, Regulatory, and
Technical Specifications User Guide (6K9678)).

Scanning Imaging Plate

1 Move to the CS 7200 scanner and make sure the plate size selector knob is set for the same size as
indicated on the plate.

2 Open the hygienic sheath.

CS 7200 User and Installation Guide (6M0940)_Ed04 47

3 Load the plate into the scanner while positioning the plate to the left direction. The indication LED is
blinking blue, indicating that the plate is loaded and the hygienic sheath can be removed.

Note: Make sure you insert the plate with the active side facing up. If the plate
is inserted when positioned upside down, an error message is displayed: Plate
loaded upside down.

4 Remove the hygienic sheath to start the scanning process.

CS 7200 starts scanning. The indication LED is blinking green during the process and the Preview
window appears showing the scan progress.

When the scan is complete, the imaging plate is erased and then ejected. The indication LED stops
blinking and remains steady green.

The image is displayed on the imaging software main screen.

48 Chapter 5 Acquiring Images

5. Check the image quality.

The ideal image quality is when the indicator of the quality of exposure is a full green bar in the Control
Panel. Avoid under-exposed or over-exposed images indicated by a partial or full red bar.

Under-exposed Image Overexposed Image

Ideal Image Quality Ideal Image Quality

CS 7200 User and Installation Guide (6M0940)_Ed04 49

Acquiring Multiple Images
Preparing the Acquisition of FMS Images
To prepare the acquisition of FMS images, follow these steps:

1 Access the Dental Imaging Software. See “Starting the Imaging Software” on page 42.
2 Click the Use a format button in the Imaging Window toolbar to access the Select a format window.

3. From the list of available formats (templates), select the required template and click Open.

50 Chapter 5 Acquiring Images

 The selected format is loaded and displayed in the Dental Imaging window. The first frame for scan is
highlighted in green.

4. Select an appropriate positioner for the region of interest and the size of the plate.

5 Prepare all imaging plates required for completing FMS template. See “Preparing the Imaging Plates”
on page 43.
6. Position the imaging plate in the mouth of the patient depending on the region of interest.

CS 7200 User and Installation Guide (6M0940)_Ed04 51

7. Move the X-ray generator tube head to the patient and align it with the tooth of the patient and the
imaging plate.

Important: Make sure that the tube head is not shaking.

8. Select the X-ray exposure time according to the region of interest and the patient type. Follow the user
instructions of your X-ray generator. The following tables provide guidelines for exposure times for an
X-ray generator at 70 kV and 7 mA. Add your values for the exposure time in seconds in the column on
the right.

Table 4 Exposure times

Parameter DC-emitter, 7mA, tube length 20 cm DC-emitter, 7mA, tube length 30 cm

recommended exposure time (s) recommended exposure time (s)
Upper jaw 60kV 70kV 60kV 70kV
incisors 0.1 0.08 0.2 0.16
pre-molars 0.125 0.1 0.25 0.2
molars 0.16 0.125 0.32 0.25
Lower jaw 60kV 70kV 60kV 70kV
incisors 0.1 0.08 0.2 0.16
pre-molars 0.125 0.1 0.25 0.2
molars 0.125 0.1 0.25 0.2
Bitewing 0.16 0.125 0.32 0.25

Important: These are suggested exposure times and need to be adjusted

for your specific X-ray generator. For dark images, reduce the exposure
time and for grainy images, increase the exposure time.

52 Chapter 5 Acquiring Images

Acquiring FMS Images
To acquire FMS images, follow these steps:

1. For each imaging plate you prepared, perform the X-ray. See “Performing the X-rays” on page 44.

2 Scan all X-rayed imaging plates in the required order displayed on the Dental Imaging screen. See
“Scanning Imaging Plate” on page 47.
The next frame to be scanned is always highlighted in green on the displayed FMS format.

Tip: For FMS, it is recommened to use the transportation box that helps to
sort the plates in the correct order.

3 Check the image quality.

The ideal image quality is when the indicator of the quality of exposure is a full green bar in the Control
Panel. Avoid under-exposed or over-exposed images indicated by a partial or full red bar.

Under-exposed Image Overexposed Image

Ideal Image Quality Ideal Image Quality

CS 7200 User and Installation Guide (6M0940)_Ed04 53

Retaking Images
If you need to retake images, after the FMS template acquisition is complete, follow these steps:

1. Click the frame for which you want to retake images. The selected frame is highlighted in green.

2. Using the mouse cursor, drag the selected image outside the template window.

54 Chapter 5 Acquiring Images

3 Close the CS 7200 window with the image to be relaced. The image is deleted from the template.
4. Perform a scan again.

5 After the scan is complete, the new image appears in the FMS template.
6 Close the template window to save the performed changes.

CS 7200 User and Installation Guide (6M0940)_Ed04 55

Manually Erasing the Plate
To manually erase a plate, perform the following steps:

1 On the Dental Imaging Software main tool bar, click the CS 7200 Configuration icon.
The CS 7200 window appears:

2 Click Erase Plate. The following dialog box appears:

3 Load the late into the scanner.

4 Wait until the erase process is complete.

To erase more plates, perform steps 1 - 4.

5 After the earse process is complete, close the CS 7200 window.

56 Chapter 5 Acquiring Images

Changing Scanner User Preferences
To change the Scanner User Preferences, perform the following steps:

1 On the Dental Imaging Software main tool bar, click the CS 7200 Configuration icon.
The CS 7200 window appears:

2 Click Preferences to open the CS 7200 Preferences window.

The CS 7200 Prefernces window contains three tabs:

 Settings

 Tools

 About

Settings Tab
The Settings tab enables user to change the scanner preferences:

1 DICOM Character Sets: select from th list of the available options.

2 Default scan resolution: select one of the available scan resolutions from the list
 Ultra High Resolution

 Super high resolution

 High resolution

 High speed

3 Scanner sound: select the check box to mute the scanner sound.
4 SMPTE: click to adjust monitor brightness and contrast.
5 Default exposure values: change the default exposure values if required.

CS 7200 User and Installation Guide (6M0940)_Ed04 57

Tools Tab
The tools tab enables the user to retrieve a scanned image in case the Dental Imaging Software crashed
unexpectedly during the scan. To retrieve the images, perform the following steps:

1 Start the Dental Imaging Software.

2 Open the file of the patient whose images you want to retrieve.
3 On the Dental Imaging Software main tool bar, click the CS 7200 Configuration icon.
The CS 7200 window appears.

4 Click Preferences to open the CS 7200 Preferences window and select the Tools tab.
The Retrieve Images button is enabled and the number of pending images is diplayed.

5 Click Retrieve Images.

58 Chapter 5 Acquiring Images

 The retrieved images are displayed. The image highlighted in orange is displayed in the preview area
next to the list.

6 Seelect the required images from the list by selecting the check box next to each image.
The Restore and Delete buttons become available.

CS 7200 User and Installation Guide (6M0940)_Ed04 59

7 Click Restore to restore the selected image to the currently opened patient.

About Tab
Open the about tab to view scanner information that includes firmware, hardware and software versions,
serial number and other details.

60 Chapter 5 Acquiring Images

Changing Scan Resolution
To chnage scan resolution, perform the following steps:

1 On the Dental Imaging Software main tool bar, click the CS 7200 Configuration icon.
The CS 7200 window appears:

2 Select the desired scan resolution and click OK to save the selection.

CS 7200 User and Installation Guide (6M0940)_Ed04 61

62 Chapter 5 Acquiring Images
6 Maintenance

For all maintenance information, refer to CS 7200 Technical Specifications, Safety and Regulatory Guide.

CS 7200 User and Installation Guide (6M0940)_Ed04 63

64 Chapter 6 Maintenance
7 Troubleshooting

Quick Troubleshooting
Occasionally, malfunctions can occur during use in the event of an incorrect action. An error
message is displayed.

During the CS 7200 power up, system performs a self test: ejects a plate (if left in the scanner) and reports
whether the system is ready for operation or a malfunction is detected.

The detected malfunction is indicated by the CS 7200 LED status and sound notification and/or by an error
message that appears on screen.

When the system functions properly, the LED is green. If the LED color is yellow or red, it indicates an
existence of the malfunction.

Indication LEDs Statuses

The below table lists the scanner LEDs status indicator states that require a corrective action:

LED Color Scanner State Remark

Blinking Yellow Power up/unload

Yellow Stand by (door closed)

Type 1: Blinking yellow - cable is disconnected

Type 2: Fast Blinking yellow - no driver
Yellow Disconnected
Type 3: Constant yellow: no UltraLite or scanner is
not ready

Blinking/Steady Red Error

CS 7200 User and Installation Guide (6M0940)_Ed04 65

The following table lists the error messages, their description and the action to take:

IMPORTANT
If an Error Code message is displayed, the malfunction persists or more
serious conditions occur, contact a qualified technician. When you call
the qualified technician have the following information ready:

 Model Serial Number

 Error Code Message

Table 5 System Errors

Symptom Cause Corrective Action

Plate size selector knob is  The scanner is turned off.  Turn on the scanner.
stuck.  The Dental Imaging Software  Open the Dental Imaging Software main
main screen is not opened. screen.
The plate cannot be loaded  The scanner is turned off.  Turn on the scanner.
into the scanner.  The Dental Imaging Software  Open the Dental Imaging Software main
main screen is not opened. screen.
Scanner returns to home The scanner was exposed to a very Reduce the ambient light to the level specified in
position unexpectedly. strong ambient light or to a camera CS 7200 Technical Specifications, Safety and
flash directed to the insertion panel. Regulatory Guide.

Scanner performs a Electrical noise from the peripheral  Make sure the scanner is located away from
spontaneous reboot. devices. the suspected noise generators.
 Connect the power supply to a separate
mains wall outlet.
The plate loading process is The hygienic sheath is partially sealed. Make sure the hygienic sheath is fully open,
not smooth and requires before loading the plate.
some force to apply.
Scanner returns to home The imaging plate was retrieved before  Wait for the scanner to return to its home
position before the loading is it was completely loaded into the position.
completed. scanner.  Perform a complete loading process.

Vertical lines appear on the Scanner was not stable or hit during the  Make sure the scanner is positioned on a
scanned image. scan. stable surface.
 Make sure you do not touch the scanner
during the scan.
During the power up, There is no power supply to the
scanner remains off and the system:
indication LED is off.
 Power Supply is not connected to
The CR icon disappears from the mains wall outlet. Make sure the Power Supply is properly
the Dental Imaging Software  Power supply is not connected to connected
toolbar. the scanner.
 Problems with the facility power
supply.
 Power Supply is damaged.
 Scanner malfunciton.

LED indicator is steady The Dental Imaging Software is  Start the Dental Imaging Software.
yellow. closed.  If the problem persists, restart the scanner.

LED indicator remains  There is no USB communication  Make sure you use the USB cable supplied
blinking yellow for more between the scanner and the with the scanner.
than one minute. computer.  Make sure the USB cable is properly
connected on both sides.
 Try to connect the USB cable to another
USB port on the computer.
 Replace the USB cable.
 Call Service.
 Scanner malfunction.

66 Chapter 7 Troubleshooting
 Symptom Cause Corrective Action
LED indicator blinks red.  Restart the Scanner.
The cause is unknown.  If problem persists, call Service.
No error message is
displayed.
LED indicator blinks red Scanner hardware malfunction.  Restart the Scanner.
during the Scanner power on  If the problem persists, repeat for three
and the noise is sounded. times.
 If problem persists, call Service.
LED indicator is red. Scanner hardware malfunction.  Restart the Scanner.
 If problem persists, call Service.
Error code #9011
LED indicator blinks red Scanner hardware malfunction.  Restart the Scanner.
Error code #9012  If problem persists, call Service.

LED indicator is red or off. Scanner hardware malfunction.  Restart the Scanner.
 If problem persists, call Service.
Error code #9014
LED indicator blinks red Insertion panel is detached from the  Properly attach the panel to the scanner.
Error code #9015 scanner. Warning: Do not change the position of the
plate selector knob.
 Click OK to close the error message and
proceed.
LED indicator blinks red The plate was not scanned and  Remove the insertion panel.
remained inside the scanner.  While holding the visible part of the plate,
Error code #9016 lift the scanner protection door.
 Remove the plate from the scanner.
 If the plate fell inside the scanner, remove
the service tray and remove the plate.
 Attach the insertion panel.
 Click OK to close the error message.
 Perform a scan.
LED indicator blinks red Scanner hardware malfunction.  Restart the Scanner.
 If problem persists, call Service.
Error code #9021, 9022,
9023
LED indicator blinks red  Scanner hardware malfunction.  Restart the Scanner.
 Power Supply malfunction.  Replace Scanner Power Supply.
Error code #9024  If problem persists, call Service.
LED indicator blinks red Scanner hardware malfunction.  Turn off the scanner.
 Wait for five minutes and restart the
Error code #9025 Scanner.
 If problem persists, call Service.
LED indicator blinks red Software files version does not match
the scanner files version. Update scanner files.
Error code #9030
LED indicator blinks red Scanner hardware malfunction.  Click OK to shut down the scanner.
 Restart the scanner. The plate is ejected.
Error code #9031  Rescan the plate.
 If the problem persists, call Service.

LED indicator blinks red Scanner hardware malfunction.  Click OK to eject the plate.
 Rescan the plate.
Error code #9032, 9036  If the problem persists, call Service.
LED indicator blinks red Scanner hardware malfunction.  Restart the scanner.
 If the problem persists, call Service.
Error code #9039
LED indicator blinks red  Plate was not loaded properly.  Click OK to eject the plate.
 Rescan the plate.
Error code #9043  If the problem persists, restart the Scanner.
 Scanner hardware malfunction.  If the problem persists, call Service.

CS 7200 User and Installation Guide (6M0940)_Ed04 67

 Symptom Cause Corrective Action
LED indicator blinks red  Plate was not ejected and erased  Click OK to eject the plate.
properly.  Erase the plate manually.
Error code #9044, 9047  If the problem persists, restart the Scanner.
 If the problem persists, call Service.
 Scanner hardware malfunction.
LED indicator blinks red Plate was not scanned properly.  Click OK to eject the plate.
Scanner hardware malfunction.  Reload the plate.
Error code #9045, 9048,
9052, 9053, 9054

LED indicator blinks red Scanner hardware malfunction.  Click OK to shut down the scanner.
 Restart the scanner.
Error code #9061-69
LED indicator blinks red  Plate was not scanned properly.  Click OK to eject the plate.
 Rescan the plate.
Error code #9046, 9049  If the problem persists, restart the Scanner.
 Scanner hardware malfunction.
 If the problem persists, call Service.
LED indicator blinks red Scanner hardware malfunction.  Click OK to close the error message.
 Call Service and continue with regular
Error code #9060 scanner operation.
 Note: This error will appear on each power
up, until it is fixed by the Service.
LED indicator blinks red Scanner hardware malfunction.  Click OK to close the error message.
 Restart the Scanner.
Error code #9080  If the problem persists, call Service.
LED indicator blinks red  Scanner hardware malfunction.  Click OK to eject the plate.
 Plate was not erased properly.  Manually erase the plate.
Error code #9081  If the problem persists, call Service.
LED indicator is steady red
Plate was loaded upside down or
Error beeps are sounded Retrieve the plate and load the plate properly.
diagonally.
when loading a plate
LED indicator blinks red  Plate was loaded upside down or  Click OK to eject the plate.
diagonally.  Load the plate properly.
Error code #9090  Plate was not scanned.
LED indicator blinks red Scanner hardware malfunction.  Click OK to shut down the scanner.
 Restart the Scanner.
Error code #90120  Rescan the plate.
 If the problem persists, call Service.
LED indicator blinks red The Scanner files are not up to date.
Update the scanner files.
Error code #90800
LED indicator blinks red Scanner drivers files are not up to date.
Update the Scanner drivers files.
Error code #90801
LED indicator blinks red  Scanner hardware malfunction.  Click OK to close the error message.
 Plate was not scanned or erased  Restart the Scanner.
Error code #90852 properly.  Reload the plate for scan.
 If the problem persists, call Service.
Plate was not ejected Plate was not properly ejected.  Remove the insertion panel.
 Remove the service tray and remove the
plate.
 Attach the insertion panel.
Scanner disconnects during External electronic noise that interferes  Verify using the original CS7200 USB cable
the scan/half image appears with communication between the with the ferrites on ot.
after scan is completed/ther scanner and the computer.  Verify that devices emitting high electronic
are lines on the image noise (such as Wi Fi routers, UPS and etc.)
are not connected in close proximity to the
scanner and do not use the same power
inlet.
 Replace the Controller Card.

68 Chapter 7 Troubleshooting
8 Appendix

Offline License Activation

If the working station computer is not connected to the internet, you need to acquire license activation code
from another device that is connected to the internet.. The following sequence takes place, when the license
activation is performed offline:

1. After the installation is complete, the license activatuion message appears:. Click Next to continue.

2. The following message appears:

3. Turn on the scanner.

CS 7200 User & Installation Guide (6M0940)_Ed04 69

4. The Offline License Activation window appears:

5. Go to https://cs-licensing-staging.carestreamdental.com/Licensing and sign in or create an account,

if you do not have one.

70 Chapter 8 Appendix
6. Click Continue to open the Product Activation and Registration - Create Customer Record page.

7. Fill in all required details and click Continue at the bottom of the page.

8. After filling in all details, an account is created and an email is sent to the provided email address.

9. Open the received email and click the provided link to activate your Carestream account.

10. After email verification is complete, click Continue.

CS 7200 User & Installation Guide (6M0940)_Ed04 71

11. Select Activate a license for a Carestream Dental Product.

12. Fill in the required product details as follows:

 Product Name: select CS 7200 from the available products list.

 Serial Number: type in the serial number that appears on the Data Plate label located on the
bottom of the scanner.

 License Key: type in the license key that appears on the post card received with the scanner.

 User Code: type in the user code that appears in the Offline License Activation window.

13. Click Continue. An email that contains product nem, product license number and activation code is
sent to your email address.

72 Chapter 8 Appendix
14. On the Activation Complete page, copy the displayed activation code..

15. Paste the copied activation code into the Offline License Activation window and click Activate.

CS 7200 User & Installation Guide (6M0940)_Ed04 73

16. After the license activation is complete, click Exit to close the Offline License Activation window.

You are returned to the CS 7200 Installation Wizard.

17. Click Finish to finish the installation process.

74 Chapter 8 Appendix
Create a New Patient Card
To create a new patient card, follow the below steps:

1. In the Patient Browser toolbar, click the Create New Patient Card button.

The Patient Card window is displayed:

2. In the Patient Card window, enter patient information.

Note: First Name, Last Name and Gender are mandatory fields. All other
fields are optional. Grayed out fields are not editable.

3. Click Create patient to save the patient card.

4. The Patient Card window closes and the new patient appears in the patient list.

CS 7200 User & Installation Guide (6M0940)_Ed04 75

76 Chapter 8 Appendix
CS 7200 User & Installation Guide (6M0940)_Ed04 77
78 Chapter 8 Appendix
9 Contact Information

Manufacturer’s Address

Carestream Health, Inc.

150 Verona Street
Rochester, NY USA 14608

Authorized Representatives
Authorized Representative in the European Community
EC REP

Carestream Health France

COPERNIC II
IMMEUBLE Le Neptune
1, rue Galilée
93192 Noisy-Le-Grand
France

Importer for European Union

Carestream Health Netherlands B.V
Bramenberg 12
3755 BZ Eemnes
The Netherlands

Representante no Brasil Carestream do Brasil Comércio e Serviços de Produtos Médicos

Ltda.
Rua Pequetita, 215 cjs.
31 E 32 Edifício Atrium VII - Vila Olímpia
São Paulo - Brazil
CEP (Zip code): 04552-060

CS 7200 User and Installation Guide (6M0940)_Ed04 79

80 Chapter 9 Contact Information
10 List of Consumables

List of Consumables

P/N Description Qty

1067495 Hygienic Sheaths #0 200 Pcs
1067503 Hygienic Sheaths #1 200 Pcs
1067511 Hygienic Sheaths #2 200 Pcs
1067545 Imaging Plate #0 4 Pcs
1067552 Imaging Plate #1 4 Pcs
1067560 Imaging Plate #2 4 Pcs
1030428 Carestream Screen Cleaner

CS 7200 User and Installation Guide (6M0940)_Ed04 81

82 Chapter 10 List of Consumables
11 Publications History

Publication Changed
Publication Date File Name Notes
No. Chapters
CS 7200 User and
2015-03 6M0940 First Release
Installation Guide
Added table to the CS 7200 User and
2015-06 6M0940 Revision 2
Consumables List Installation Guide

Updated manual to CS 7200 User and

2017-05 6M0940 match the new SW Revision 4
Installation Guide
version

CS 7200 User and Installation Guide (6M0940)_Ed04 83

Carestream Dental
A Division of Carestream Health, Inc.
150 Verona St.
Rochester, NY 14608
USA

For more information, visit: www.carestreamdental.com

To give documentation feedback, visit:
www.carestreamdental.com/documentationfeedback

©Carestream Health, Inc., 2017. 6M0940 Ed04 2017-04