Scribd
Upload
3 views

iflex loop detector

The document provides safety information and specifications for the iFlex-1500-xx, iFlex-3000-xx, and iFlex-6000-xx Thin-Flexi Current Probes. It emphasizes the importance of following safety guidelines to prevent electrical shock and injury, including proper usage, personal protective equipment, and regular inspection of the product. Additionally, it outlines warranty details and compliance with safety standards and directives.

Uploaded by

wongderder
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
3 views

iflex loop detector

The document provides safety information and specifications for the iFlex-1500-xx, iFlex-3000-xx, and iFlex-6000-xx Thin-Flexi Current Probes. It emphasizes the importance of following safety guidelines to prevent electrical shock and injury, including proper usage, personal protective equipment, and regular inspection of the product. Additionally, it outlines warranty details and compliance with safety standards and directives.

Uploaded by

wongderder
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

iFlex-1500-xx

iFlex-3000-xx
iFlex-6000-xx
Thin-Flexi Current Probe
Safety Information
To register your product, or to view, print, or download the latest
manual or manual supplement go to our website: www.fluke.com.
A Warning identifies hazardous conditions and procedures that
are dangerous to the user.

XW Warning
To prevent possible electrical shock, fire, or personal
injury:
 Read all safety information before you use the
Product.
 Use the Product only as specified, or the protection
supplied by the Product can be compromised.
 Comply with local and national safety codes. Use
personal protective equipment (approved rubber
gloves, face protection, and flame-resistant clothes)
to prevent shock and arc blast injury where hazardous
live conductors are exposed.
 Do not use the Product around explosive gas, vapor,
or in damp or wet environments.
 Do not touch voltages >30 V ac rms, 42 V ac peak, or
60 V dc.

PN 4272192 (English)
September 2013 Rev. 1, 10/21
©2013-2021 Fluke Corporation. All rights reserved. Specifications are
subject to change without notice. All Product names are trademarks of
their respective companies.
Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 P.O. Box 1186
Everett WA 98206-9090 5602 BD Eindhoven
U.S.A. The Netherlands
 De-energize the circuit or wear personal protective
equipment in compliance with local requirements
before you apply or remove the Product.
 Do not use the Product if it is damaged.
 Do not use the Product if it operates incorrectly.
 Before each use, examine the Product. Look for cracks
or missing pieces of the clamp housing or output cable
insulation. Also look for loose or weakened
components. Carefully examine the insulation around
the jaws.
 Do not use the Flexible Current Probe if it has
damaged insulation, exposed metal, or if the wear
indicator is visible.
 Do not use a current measurement as an indication
that a circuit is safe to touch. A voltage measurement
is necessary to know if a circuit is hazardous.
 Have an approved technician repair the Product.
 Remove the input signals before you clean the
Product.

Specifications
Safety ...........................................IEC 61010-1: Pollution degree 2
IEC 61010-2-032: CAT IV 600 V,
CAT III 1000 V
Temperature
Operating ...............................-20 °C to 70 °C (-4 °F to 158 °F)
Temperature of conductor under
test shall not exceed 80 °C (176 °F)
Storage ...................................-40 °C to 80 °C (-40 °F to 176 °F)
Altitude
Operating ...............................2000 m
Storage ...................................12 000 m
Symbols
The table below is a list of the symbols that can be used on the
Product or in this document.

Symbol Description
» Consult user documentation.
W WARNING. RISK OF DANGER.
WARNING. HAZARDOUS VOLTAGE. Risk of electric
X
shock.
T Double insulation
Measurement Category II is applicable to test and
measuring circuits connected directly to utilization
¼
points (socket outlets and similar points) of the low
voltage MAINS installation.
Measurement Category III is applicable to test and
½ measuring circuits connected to the distribution
part of the building’s low-voltage MAINS installation.
Measurement Category IV is applicable to test and
¾ measuring circuits connected at the source of the
building’s low-voltage MAINS installation.

P Conforms to European Union directives.

This product complies with the WEEE Directive


marking requirements. The affixed label indicates
that you must not discard this electrical/electronic
product in domestic household waste. Product
~ Category: With reference to the equipment types in
the WEEE Directive Annex I, this product is classed
as category 9 "Monitoring and Control
Instrumentation" product. Do not dispose of this
product as unsorted municipal waste.
LIMITED WARRANTY AND LIMITATION OF LIABILITY
This Fluke product will be free from defects in material and
workmanship for one year from the date of purchase. This
warranty does not cover fuses, disposable batteries, or damage
from accident, neglect, misuse, alteration, contamination, or
abnormal conditions of operation or handling. Resellers are not
authorized to extend any other warranty on Fluke’s behalf. To
obtain service during the warranty period, contact your nearest
Fluke authorized service center to obtain return authorization
information, then send the product to that Service Center with a
description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR PURPOSE,
ARE EXPRESSED OR IMPLIED. FLUKE IS NOT LIABLE FOR ANY
SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES OR LOSSES, ARISING FROM ANY CAUSE OR THEORY.
Since some states or countries do not allow the exclusion or
limitation of an implied warranty or of incidental or consequential
damages, this limitation of liability may not apply to you.
11/99

You might also like