Sand filters are used as a step in the water treatment process of water purification.

There are three main types; rapid (gravity) sand filters, upward flow sand filters
and slow sand filters. All three methods are used extensively in the water
industry throughout the world. The first two require the use of flocculant chemicals to
work e ectively while slow sand filters can produce very high quality water
with pathogens removal from 90% to >99% (depending on the strains), taste and odour
without the need for chemical aids.[1] Sand filters can, apart from being used in water
treatment plants, be used for water purification in singular households as they use
materials which are available for most people.[2]

History

[edit]

The history of separation techniques reaches far back, as filter materials were already
in use during ancient periods. Rushes and genista plants were used to fill sieving
vessels that separated solid and liquid materials. The Egyptians also used porous clay
vessels to filter drinking water, wine and other liquids. [3]

Sand bed filtration concept

[edit]

Sand filters on a tomato farm in California

A sand bed filter is a kind of depth filter. Broadly, there are two types of filters for
separating particulate solids from fluids:

 Surface filters, where particulates are captured on a permeable surface

 Depth filters, where particulates are captured within a porous body of

material.[4]

In addition, there are passive and active devices for causing solid-liquid separation
such as settling tanks, self-cleaning screen filters, hydrocyclones and centrifuges.[4]

There are several kinds of depth filters, some employing fibrous material and others
employing granular materials. Sand bed filters are an example of a granular loose
media depth filter. They are usually used to separate small amounts (<10 parts per
million or <10 g per cubic metre) of fine solids (<100 micrometres) from aqueous
solutions.[5]: 302–303 In addition, they are usually used to purify the fluid rather than
capture the solids as a valuable material. Therefore they find most of their uses in
liquid e luent (wastewater) treatment.

Particulate solids capture mechanisms

[edit]

Sand bed filters work by providing the particulate solids with many opportunities to be
captured on the surface of a sand grain. As fluid flows through the porous sand along a
tortuous route, the particulates come close to sand grains. They can be captured by
one of several mechanisms:

 Direct collision

 Van der Waals or London force attraction

 Surface charge attraction

 Di usion[4]

In addition, particulate solids can be prevented from being captured by surface charge
repulsion if the surface charge of the sand is of the same sign (positive or negative) as
that of the particulate solid. Furthermore, it is possible to dislodge captured
particulates although they may be re-captured at a greater depth within the bed.
Finally, a sand grain that is already contaminated with particulate solids may become
more attractive or repel addition particulate solids. This can occur if by adhering to the
sand grain the particulate loses surface charge and becomes attractive to additional
particulates or the opposite and surface charge is retained repelling further
particulates from the sand grain.

In some applications it is necessary to pre-treat the e luent flowing into a sand bed to
ensure that the particulate solids can be captured. This can be achieved by one of
several methods:

 Adjusting the surface charge on the particles and the sand by changing the pH

 Coagulation – adding small, highly charged cations (aluminium 3+ or calcium 2+

are usually used)
  Flocculation – adding small amounts of charge polymer chains which either
form a bridge between the particulate solids (making them bigger) or between
the particulate solids and the sand.

Operating regimes

[edit]

They can be operated either with upward flowing fluids or downward flowing fluids the
latter being much more usual. For downward flowing devices the fluid can flow under
pressure or by gravity alone. Pressure sand bed filters tend to be used in industrial
applications and often referred to as rapid sand bed filters. Gravity fed units are used
in water purification especially drinking water and these filters have found wide use in
developing countries (slow sand filters).

Overall, there are several categories of sand bed filter:

 rapid (gravity) sand filters

 rapid (pressure) sand bed filters

 upflow sand filters

 slow sand filters

The sketch illustrates the general structure of a rapid pressure sand filter. The filter
sand takes up most space of the chamber. It sits either on a nozzle floor or on top of a
drainage system which allows the filtered water to exit. The pre-treated raw water
enters the filter chamber on the top, flows through the filter medium and the e luent
drains through the drainage system in the lower part. Large process plants have also a
system implemented to evenly distribute the raw water to the filter. In addition, a
distribution system controlling the air flow is usually included. It allows a constant air
and water distribution and prevents too high water flows in specific areas. A typical
grain distribution exits due to the frequent backwashing. Grains with smaller diameter
are dominant in the upper part of the sand layer while coarse grain dominates in the
lower parts.

Two processes influencing the functionality of a filter are ripening and regeneration.
At the beginning of a new filter run, the filter e iciency increases simultaneously with
the number of captured particles in the medium. This process is called filter ripening.
During filter ripening the e luent might not meet quality criteria and must be
reinjected at previous steps in the plant.[6] Regeneration methods allow the reuse of
the filter medium. Accumulated solids from the filter bed are
removed.[6] During backwashing, water (and air) is pumped backwards through the
filter system. Backwash water may partially be reinjected in front of the filter process
and generated sewage needs to be discarded. The backwashing time is determined by
either the turbidity value behind the filter, which must not exceed a set threshold, or
by the head loss across the filter medium, which must also not exceed a certain value.

Rapid pressure sand bed filter design

[edit]

Rapid pressure filter 1=raw water, 2=filtered water,

3=tank, 4=outlet flushing water, 5=inlet flushing water, 6=retraction line, 7=scavenging
air, 8=injector, 9=supporting layer, 10=filter sand, 11=flushing funnel, 12=ventilation

Smaller sand grains provide more surface area and therefore a higher
decontamination of the inlet water, but it also requires more pumping energy to drive
the fluid through the bed. A compromise is that most rapid pressure sand bed filters
use grains in the range 0.6 to 1.2 mm although for specialist applications other sizes
may be specified. Larger feed particles (>100 micrometres) will tend to block the pores
of the bed and turn it into a surface filter that blinds rapidly. Larger sand grains can be
used to overcome this problem, but if significant amounts of large solids are in the
feed they need to be removed upstream of the sand bed filter by a process such as
settling.[5]: 302–303
The depth of the sand bed is recommended to be around 0.6–1.8 m (2–6 ft) regardless
of the application. This is linked to the maximum throughput discussed below. [5]: 302–303

Guidance on the design of rapid sand bed filters suggests that they should be operated
with a maximum flow rate of 9 m3/m2/hr (220 US gal/ft2/hr).[7] Using the required
throughput and the maximum flow rate, the required area of the bed can be
calculated.

The final key design point is to be sure that the fluid is properly distributed across the
bed and that there are no preferred fluid paths where the sand may be washed away
and the filter be compromised.

Rapid pressure sand bed filters are typically operated with a feed pressure of 2 to 5
bar(a) (28 to 70 psi(a)). The pressure drop across a clean sand bed is usually very low. It
builds as particulate solids are captured on the bed. Particulate solids are not
captured uniformly with depth, more are captured higher up with bed with the
concentration gradient decaying exponentially.[5]: 302–303

This filter type will capture particles down to very small sizes, and does not have a true
cut o size below which particles will always pass. The shape of the filter particle size-
e iciency curve is a U-shape with high rates of particle capture for the smallest and
largest particles with a dip in between for mid-sized particles.[7]

The build-up of particulate solids causes an increase in the pressure lost across the
bed for a given flow rate. For a gravity fed bed when the pressure available is constant,
the flow rate will fall. When the pressure loss or flow is unacceptable and the filter is
not working e ectively any longer, the bed is remove the accumulated particles. For a
pressurized rapid sand bed filter this occurs when the pressure drop is around 0.5 bar.
The backwash fluid is pumped backwards through the bed until it is fluidized and has
expanded by up to about 30% (the sand grains start to mix and as they rub together
they drive o the particulate solids). The smaller particulate solids are washed away
with the backwash fluid and captured usually in a settling tank. The fluid flow required
to fluidize the bed is typically 3 to 10 m3/m2/hr but not run for long (a few minutes).[5]: 224–
235
Small amounts of sand can be lost in the backwashing process and the bed may
need to be topped up periodically.

Slow sand filter design

[edit]

As the title indicates, the speed of filtration is changed in the slow sand filter, however,
the biggest di erence between slow and rapid sand filter, is that the top layer of sand
is biologically active, as microbial communities are introduced to the system. The
recommended and usual depth of the filter is 0.9 to 1.5 meters. Microbial layer is
formed within 10–20 days from the start of the operation. During the process of
filtration, raw water can percolate through the porous sand medium, stopping and
trapping organic material, bacteria, viruses and cysts such
as Giardia and Cryptosporidium. The regeneration procedure for slow sand filters is
called scraping and is used to mechanically remove the dried out particles on the
filter. However, this process can also be done under water, depending on the
individual system. Another limiting factor for the water being treated is turbidity,
which is for slow sand filters defined to be 10 NTU (Nephelometric Turbidity Units).
Slow sand filters are a good option for limited budget operations as the filtration is not
using any chemicals and requires little or no mechanical assistance. However,
because of a continuous growing population in communities, slow sand filters are
being replaced for rapid sand filters, mostly due to the running period length.

Characteristics of rapid and slow sand filters [6]

[edit]

Characteristics Rapid sand filter Slow sand filter

Filtration rate [m/h] 5–15 0.08–0.25

Media e ective size [mm] 0.5–1.2 0.15–0.30

Bed depth [m] 0.6–1.9 0.9–1.5

Run length 1–4 days 1–6 months

Ripening period 15 min – 2 h Several days

Regeneration method Backwashing Scraping

Maximum raw-water turbidity Unlimited with proper pretreatment 10 NTU

Upflow bed filter design

[edit]

The continuously backflushing or upflow sand filter is the newest operating regime.
The clearest di erence with respect to the previous ones, is that the water to be
filtered is fed from the bottom and the filtered water is obtained at the top. This
reverse flow allows the backwash process to be integrated in the filtration process,
thus decreasing the amount of rinse water to be used and reducing cleaning time. The
maximum loading is about 5.4 lps/m2 with a constant head loss of 0.6 m. [8]

Mixed bed filters

[edit]

Filters that have di erent filtering layers, are called mixed bed filters or multimedia
filters. Sand is a common filter material, but anthracite, granular activated carbon
(GAC), garnet and ilmenite are also common filter materials. Anthracite is a harder
material and has less volatile compared to other coals. Ilmenite and garnet are heavy
compared to sand. Garnet consists of several minerals, causing a shifting red colour.
Ilmenite is an oxide of iron and titanium. GAC can be used in the process of adsorption
and filtration at the same time. These materials can be used both alone, or combined
with other media. But the filtering layers will be always arranged by density, heavier
compounds will be settled in the bottom, while the lighter ones will be located on top.
Di erent combinations give di erent filter classification and also di erent porosity
throughout the filter, which is translated into di erent pressure drop. A very common
arrangement for these filers is composed of: anthracite on top, sand and garnet, with a
support of gravel at the bottom. The depth of these filters is normally between 0.6-1 m,
above 1 m the pressure drop rises sharply and less than 0.6 m reduces the thickness
of each filtering layer, thus reducing its e icienciy. Normal operating flux and pressure
drop are between 3-7 gpm/ft2 and 3-7 psi. When pressure drop increases above 10 psi,
a backwash operation ins needed, which consist of reversing the flow (water goes
upwards) in order to remove the particles trapped in the filtering media, and this will
exit from the top of the filter with the backwash water. Common for the backwash is
around 3 times the normal filtering flux (must be high enough to lift the filtering media
to remove the particles trapped in it). Monomedia is a one layered filter, commonly
consisting of sand and is today replaced by newer technology. Deep-bed monomedia
is also a one layered filter which consist of either anthracite or GAC. The deep-bed
monomedia filter is used when there is a consistent water quality and this gives a
longer run time. Dual media (two layered) often contain a sand layer in the bottom with
an anthracite or GAC layer on top. Trimedia or mixed media is a filter with three layers.
Trimedia often have garnet or ilmenite in the bottom layer, sand in the middle and
anthracite at the top.

Uses in water treatment

[edit]
All of these methods are used extensively in the water industry throughout the world.
The first three in the list above require the use of flocculant chemicals to work
e ectively. Slow sand filters produce high-quality water without the use of chemical
aids.

Passing flocculated water through a rapid gravity sand filter strains out the floc and
the particles trapped within it, reducing numbers of bacteria and removing most of the
solids. The medium of the filter is sand of varying grades. Where taste and odor may be
a problem (organoleptic impacts), the sand filter may include a layer of activated
carbon to remove such taste and odor.

Sand filters become clogged with floc or bioclogged after a period in use. Slow sand
filters are then scraped (see above) while rapid sand filters are backwashed or
pressure washed to remove the floc. This backwash water is run into settling tanks so
that the floc can settle out and it is then disposed of as waste material. The
supernatant water is then run back into the treatment process or disposed of as a
waste-water stream. In some countries, the sludge may be used as a soil conditioner.
Inadequate filter maintenance has been the cause of occasional drinking water
contamination.

Sand filters are occasionally used in the sewage treatment as a final polishing stage.
In these filters the sand traps residual suspended material and bacteria and provides
a physical matrix for bacterial decomposition of nitrogenous material,
including ammonia and nitrates, into nitrogen gas.

Sand filters are one of the most useful treatment processes as the filtering process
(especially with slow sand filtration) combines within itself many of the purification
functions.[9]

Advantages and limitations

[edit]

One of the advantages of sand filters is that they are useful for di erent applications.
Moreover, the di erent types of operation modes: rapid, slow and Upflow, allow some
flexibility to adapt the filtration method to the necessities and requirements of the
users. Sand filters allow a high e iciency for color and microorganisms removal, and
as they are very simple, operating costs are very low. What is more, its simplicity
makes the automation of the processes easier, thus requiring less human
intervention.
The main limitations of this technology would be related to the clogging, that is, the
obstruction of the filter media, which requires a significant amount of water to carry
out the backflush operation and the use of chemicals in the pretreatment.
Furthermore, slow sand filters usually require larger land areas compared to the rapid
flow, especially if the raw water is highly contaminated. However, despite these
limitations, they o er much more capabilities and that is why they are extensively
used in the industry.[10][11]

Challenges in the application process

[edit]

In the process of water treatment, one should be aware of certain factors that might
cause serious problems if not treated properly. Aforementioned processes such as
filter ripening and backwashing influence not only the water quality but also the time
needed for the full treatment. Backwashing reduces also the volume of the e luent. If
a certain amount of water has to be delivered to e.g. a community, this water loss
needs to be considered. In addition, backwashing waste needs to be treated or
properly discarded. From the chemical perspective, varying raw water qualities and
changes in the temperature e ect, already at the entrance to the plant, the e iciency
of the treatment process.

Considerable uncertainty is involved regarding models used to construct sand filters.

This is due to mathematical assumptions that have to be made such as all grains being
spherical. The spherical shape a ects the interpretation of the size since the diameter
is di erent for spherical and non-spherical grains. The packing of the grains within the
bed is also dependent on the shape of the grains. This then a ects the porosity and
hydraulic flow.[6]

Uses in industry

[edit]

Sand filters are used in various sectors and processes, where far-reaching removal of
suspended matter from water or wastewater is required.

Sectors where sand filtration is implemented include drinking water production,

swimming pools, car washes, groundwater treatment, RWZI, slaughterhouses, fruit
and vegetable processing industry, drinks, food industry, surface treatment of metals,
…

Cooling water production, drinking water preparation, pre-filtration in active carbon

treatments and membrane systems, and the filtration of swimming pool water.
 Iron-removal from groundwater using aeration and sand filtration.

 Final purification of wastewater, follow-up to metal precipitation and

sedimentation, to remove residual traces of metal-based sludge.

 Final purification of wastewater produced in the production of iron, steel and

non-ferro alloys. Sand filtration can be preceded by processes like
precipitation/sedimentation, coagulation/flocculation/sedimentation and
flotation.

 Purification of wastewater containing sand-blasting grit and paint particles, at

shipyards for example.

 Also used as final purification (or prior to active carbon filtration) to permit re-
use.

 Used in greenhouse horticulture as drain-water disinfectant (slow sand filter).

 Stormwater filtration used for filtering pollutants from surface runo .

 Sewage provides a physical matrix to decompose nitrogen based compounds

such ammonia.[12]