Simulation manual:
Phase Difference Between Sound Waves
https://physics-zone.com/sim/phase-diff-sound-waves-simulation/
Introduction:
With this rich simulation, you can visualize and measure the phase difference between
two sound waves using two microphones connected to an oscilloscope. Moreover, you
can determine the speed of sound in air by measuring the distance between the two
microphones when their waveforms are in phase, taking into account the frequency of
the sound wave that is controlled by the sine wave generator.
The target users:
This simulation is instrumental and informative for students who want to virtually
perform the experiment without the need for a real lab (or in the case of lab equipment
shortage). They can record measurements of several physical quantities such as the
phase shift between the two waveforms, the wavelength of the sound wave and the
Page 1 of 18
frequency of the sound wave, etc.., and from these results, they can determine the speed
of sound in air. The ambient temperature of this experiment is between 25ºC and 30ºC.
The simulation is also invaluable and handy for teachers and lab instructors who want to
engage their students in performing lab activities on sound and draw conclusions and
discover the underlying principles.
I advise the instructors who want to benefit from this simulation to introduce the
experiment in a directed discovery approach. This way, the students are guided through
repeating the experiment to discover the underlying principles rather than receiving
them.
Importance of the simulation:
Setting up experiments to visualize the sound waves on an oscilloscope is intricate and
can be expensive. Its equipment is not easily found in every school lab. So, this
simulation makes it easy for high-school and undergraduate students to perform an
affordable activity that enables them to acquire the required skills and knowledge in this
topic.
Of course, it is much better to perform a real experiment when possible. However, the
virtual experiment is much appreciated in the case of a shortage of equipment or for a
preliminary activity to prepare the students for the real lab.
Instructional designers and course creators may find that this simulation facilitates their
work.
A short introduction to sound waves and how to determine their
speed:
Definitions:
The period: is the time taken for one complete cycle of vibration to pass a given point
on the wave. Its base SI unit is the second.
The frequency: is the number of wave crests that pass a point in one second (a wave
crest is the peak of the wave). Its base SI unit is the hertz.
The amplitude: is the maximum displacement moved by a point on a wave measured
from its equilibrium position.
The following figure illustrates the concept of the period and the amplitude.
Page 2 of 18
The wavelength: is the length of the shortest repeating part of the wave, as shown in the
following figure.
Important note: The previous two figures are completely different graphs. The first
represents the variations of the amplitude as a function of time, while the second
represents the variations of the displacement as a function of position.
Page 3 of 18
The phase of a point on a wave: is the fraction of a period that a point completes after
last passing through the reference.
In phase: Two waves of the same frequency are in phase when they are perfectly
aligned, that is, when the crests or the troughs of the two waves happen at the same
instants of time. The following figure illustrates this concept.
Out of phase: If two waves are not in phase, they are said to be out of phase. The
following figure illustrates this concept.
Page 4 of 18
In antiphase: Two waves of the same frequency are said to be in antiphase when the
crests of one happen at the same instant as the troughs of the other, as shown in the
following figure.
How to calculate the phase difference between two waveforms on the
oscilloscope:
One of the usages of this simulation is to practice determining the phase difference
between two waveforms on the screen of the oscilloscope. The following figure
illustrates this concept.
First measure the shift (the number of divisions X) between the two waveforms on the x-
axis, its unit is in divisions (div). Also, measure the length of one period in divisions (T).
Page 5 of 18
Bear in mind that a one-period time difference corresponds to an angular phase
difference of 2 rad. So:
𝑇 (𝑑𝑖𝑣) → 2𝜋 (𝑟𝑎𝑑)
𝑋 (𝑑𝑖𝑣 ) → 𝜙 (𝑟𝑎𝑑)
By cross multiplication, we conclude that:
𝑋
𝜙= ∙ 2𝜋 (𝑟𝑎𝑑)
𝑇
How to determine the speed of sound in air using the equipment
presented in this experiment:
An application of this simulation is to find the speed of sound in air. The equipment
used is an oscilloscope, sine wave generator, loudspeaker, and two microphones.
As shown in the following figure, the loudspeaker is connected to the output of the sine
wave generator, and the two microphones are connected to the two input channels of the
oscilloscope. The sine wave generator feeds the loudspeaker with a sine wave electrical
signal, so the loudspeaker converts this electrical signal into a sound wave. This sound
wave is called “pure sound” since it is monotonic. The two microphones receive the
sound emitted by the loudspeaker and convert it into electrical signals that are input to
the channels of the oscilloscope.
Page 6 of 18
The two input signals are displayed on the screen of the oscilloscope simultaneously
when you select the “Dual” mode on the oscilloscope. Initially, the two microphones are
at the same distance from the loudspeaker, so the sound waves they receive are in phase,
and so are their waveforms on the screen of the oscilloscope. When you move one of the
microphones, you will notice that the amplitude of the related waveform decreases as
you move the microphone away since the sound it receives becomes weaker. But what
matters is that the related waveform shifts horizontally on the screen, so there becomes a
phase difference between the two waveforms and are said to be out of phase. Move the
microphone furthermore until the two waveforms become in phase again for the first
time, as shown in the following figure. At this point, the distance between the two
microphones is equal to the wavelength of the sound wave they receive. Measure this
distance and multiply it by the frequency of the sound wave (which is the frequency
given by the sine wave generator) and you will get the speed of sound. Mathematically:
𝑣 =𝜆∙𝑓
Where v is the speed of sound, is the wavelength of the sound wave, and f is the
frequency of the sound wave.
If you furthermore move the microphone until the two waveforms become in phase for
the second time, then the distance between the two microphones is twice the
wavelength, and so on. Mathematically:
𝑑𝑖𝑛𝑝ℎ𝑎𝑠𝑒 = 𝑘 ∙ 𝜆
Where k is an integer.
Page 7 of 18
Alternatively, you can move one microphone until the waveforms become in antiphase
for the first time, as shown in the following figure. In this case, the distance between the
two microphones is half the wavelength. You must multiply it by two to obtain the
wavelength.
Moreover, if you move the microphone furthermore until the waveforms become in
antiphase for the second time, then the distance between the two microphones is three
halves the wavelength, and so on. Mathematically:
𝜆
𝑑𝑎𝑛𝑡𝑖𝑝ℎ𝑎𝑠𝑒 = (2𝑘 + 1) ∙
2
Where k is an integer.
Of course, there are other experiments with a different set of equipment to measure the
speed of sound in air.
Working guidelines for the simulations:
In this section, we are going through each element of the simulation and explaining its
function.
Maximize / Minimize toggle button: Click on this button to enter full-screen mode or to
restore the window mode.
Page 8 of 18
Sine Wave Generator: This instrument supplies a sine wave electrical signal. The signal
is input to the loudspeaker via connecting wires. Note that you must turn it on to operate
the loudspeaker.
ON/OFF switch: This is used to turn on or off the Sine Wave Generator.
Frequency knob: You can rotate this knob to vary the value of the frequency.
Frequency ranges: You can select a range so you vary the frequency accordingly using
the frequency knob.
Page 9 of 18
Amplitude knob: You can rotate this knob to vary the value of the amplitude of the
signal.
Loudspeaker: This instrument receives the electrical signal from the sine wave generator
and converts it into a sound signal.
Microphones: These are used to receive the sound emitted by the loudspeaker. Note that
you can drag them.
Sound mute toggle button: Click this button to toggle sound OFF/ON.
Distance between markers: This box displays the distance between the vertical markers.
Page 10 of 18
Show Markers: Tick this check button to enable the visibility of the vertical markers.
When you want to measure the horizontal distance between the two microphones, drag
these markers and place one at one microphone and the other at the other microphone,
and the distance between the two microphones will be displayed inside the textbox
labeled “Distance between markers”.
Oscilloscope: used for visualizing electrical signals.
Page 11 of 18
ON/OFF switch: This is used to turn on or off the oscilloscope.
The screen of the oscilloscope: is where the input signals are displayed. The displayed
signals are "waveforms". The vertical axis represents the voltage and the horizontal axis
represents the time. Note that the screen is divided into squares. Each square is a
division "div". Each division is divided into five subdivisions. So each subdivision
equals 0.2 div.
Page 12 of 18
Channel selector: this is used to select the input to be displayed on the screen.
Channel I & Channel II: The oscilloscope has two inputs and can trace the two input
signals simultaneously or separately.
Page 13 of 18
Inputs: Each channel has an input where you can connect the probe.
AC/DC/GND Selector: When this is set to "AC", the DC part of the signal is filtered out.
When the selector is set to ground "GND", the screen will display zero volts. This is
used for calibrating the zero level of the display. When the selector is set to "DC", the
entire signal will be displayed.
Page 14 of 18
Vertical sensitivity: Each channel has its own vertical sensitivity, which is the scale to
which the input signal is traced on the screen. In other words, it determines how many
volts are represented in a vertical division.
Y-Position: Each channel has a knob for displacing the signal upwards or downwards.
This is useful in the measurements and comparison of signals.
Page 15 of 18
Invert button: This is used to invert (flip) the signal vertically.
Horizontal sensitivity: Use this knob to change the time scale on the horizontal axis. In
other words, this determines how many milliseconds or microseconds are represented in
a horizontal division.
Page 16 of 18
Sweep button: this is used to turn ON/OFF the sweeping. If the sweep is OFF, the screen
will display a luminous dot. Otherwise, it will display a curve.
X-position: Use this knob to displace the waveform horizontally to the left or the right.
This is useful in measurement.
Page 17 of 18
Intensity: Use this knob to control the intensity of the luminous lines displayed on the
screen.
Conclusion:
With this simulation, which is rich in controls and visuals, the learner can observe and
practice measuring the phase difference between two waveforms on the oscilloscope.
She can also determine the speed of sound in air. And with the proper instructional
methodologies, the instructor will be able to empower the sense of discovery in the
learners and introduce the concept of synchronization of sound waves and how to
measure the speed of sound in a clear and visually rich presentation and enable the
learners to acquire the required learning objectives.
It is worth mentioning that this simulation is coded with the latest HTML5/JavaScript
web tools.
Page 18 of 18
