PARTS LIST

ITEM QTY PART NO. PART DESCRIPTION LENGTH UNIT WT. NET WT.
1 2 X-VFAW SUPPORT ARM 71.41 142.81
2 1 X-HDCAMTBW CLAMP WELDMENT FOR BCAM-HD 33.86 33.86
3 1 X-MHTPHD MULTI-HOLE TAPER PLATE WELDMENT 36.24 36.24
4 1 X-HDCAMSS ANGLE ADJUSTMENT WELDMENT FOR BCAM-HD 16.39 16.39
5 2 X-VFAPL4 VFA-HD PIVOT PLATE 12 in 15.88 31.77
6 2 X-LCBP4 BENT BACKING PLATE 13 in 19.00 38.01
7 4 X-SPTB SLIDING PIPE TIE BACK PLATE 5 1/2 in 5.87 23.49
8 1 X-HDCAMSP POSITIONING PLATE WELDMENT FOR BCAM-HD 2.58 2.58
9 4 X-TBCA TIE BACK CLIP ANGLE 2.01 8.02
10 10 SCX2 CROSSOVER PLATE 7 in 4.80 47.96
11 4 MCP CLAMP HALF 1/2" THICK, 11-5/8" LONG 12 1/16 in 3.59 14.37
12 8 DCP 1/2" THICK, 5-3/4" CNTER TO CENTER CLAMP HALF 8 1/8 in 2.36 18.90
13 2 P2126 2-3/8" X 126" (2" SCH. 40) GALVANIZED PIPE 126 in 40.75 81.50
14 2 P30150 2-7/8'' X 150" (2-1/2" SCH. 40) GALVANIZED PIPE 150 in 76.94 153.87
15 4 A34212 3/4" x 2-1/2" UNC HEX BOLT (A325) 2 1/2 in 0.48 1.92
16 4 G34FW 3/4" HDG USS FLATWASHER 0.06 0.24
17 4 G34LW 3/4" HDG LOCKWASHER 0.04 0.17
18 4 G34NUT 3/4'' HDG HEAVY 2H HEX NUT 0.21 0.85
19 8 G58R-18 5/8" x 18" THREADED ROD (HDG.) 1.57 12.54
20 4 G58R-12 5/8" x 12" THREADED ROD (HDG.) 1.05 4.18
21 4 G58R-8 5/8" x 8" THREADED ROD (HDG.) 0.70 2.79
22 4 X-UB5300 5/8" X 3" X 5-1/4" X 2-1/2" U-BOLT (HDG.) 1.15 4.60
23 8 X-UB5258 5/8" X 2-5/8" X 4-1/2" X 2" U-BOLT (HDG.) 1.00 8.00
24 2 G5807 5/8'' x 7" HDG HEX BOLT GR5 FULL THREAD 7 in 0.70 1.41
25 1 G5806 5/8'' x 6" HDG HEX BOLT GR5 FULL THREAD 6 in 0.62 0.62
26 8 G5804 5/8" x 4" HDG HEX BOLT GR5 0.44 3.55
27 4 G5802 5/8" x 2" HDG HEX BOLT GR5 0.27 1.08
28 8 A582114 5/8'' x 2-1/4" HDG A325 HEX BOLT 2 1/4 in 0.31 2.50
29 25 G58FW 5/8" HDG USS FLATWASHER 1/8 in 0.07 1.76
30 66 G58LW 5/8" HDG LOCKWASHER 0.03 1.72
31 71 G58NUT 5/8'' HDG HEAVY 2H HEX NUT 0.13 9.22
32 48 X-UB1300 1/2" X 3" X 5" X 2" GALV U-BOLT 0.74 35.45
33 20 X-UB1212 1/2" X 2-1/2" X 4-1/2" X 2" GALV. U-BOLT 0.66 13.13
34 80 G12FW 1/2" HDG USS FLATWASHER 3/32 in 0.03 2.73
35 80 G12LW 1/2" HDG LOCKWASHER 1/8 in 0.01 1.11
36 80 G12NUT 1/2'' HDG HEAVY 2H HEX NUT 0.07 5.73
37 5 P30120 2-7/8" x 120" (2-1/2" SCH. 40) GALVANIZED PIPE 120 in 58.07 290.33
TOTAL WT. # 1055.41

TOLERANCE NOTES DESCRIPTION

Locations:
12' 6" HEAVY DUTY New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: Engineering Atlanta, GA
V-FRAME ASSEMBLY Support Team: Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030")
W/ 2 STIFF ARMS 1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES & MOUNT PIPES
valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

1 OF 5
ALL OTHER ASSEMBLY (± 0.060") SP1 CSL 1/25/2017 VFA12-WLL-30120

PAGE
A UPDATED BCAM VERSION 1 TO BCAM VERSION 2 SP1 CSL 7/2/2018
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
REV DESCRIPTION OF REVISIONS CPD BY DATE THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT

REVISION HISTORY
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 5/3/2018 VFA12-WLL-30120
 TIE-BACK POSITIONS

11" 11" 11"

MAX. MAX. 11" 11" MAX.
TIE-BACK POSITION 1 MAX. MAX. TIE-BACK POSITION 3
-20° / +20° TOP PARALLEL TIE-BACK POSITION 2 -20° SAME SIDE STACKED
-20° / -20° TOP CROSS

TOLERANCE NOTES DESCRIPTION

Locations:
12' 6" HEAVY DUTY New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: Engineering Atlanta, GA
V-FRAME ASSEMBLY Support Team: Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030")
W/ 2 STIFF ARMS 1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES & MOUNT PIPES
valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

2 OF 5
ALL OTHER ASSEMBLY (± 0.060") SP1 CSL 1/25/2017 VFA12-WLL-30120

PAGE
A UPDATED BCAM VERSION 1 TO BCAM VERSION 2 SP1 CSL 7/2/2018
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
REV DESCRIPTION OF REVISIONS CPD BY DATE THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT

REVISION HISTORY
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 5/3/2018 VFA12-WLL-30120
 ANGLE CALIBRATING PROCEDURE:

1. MEASURE TOWER TAPER

AND PICK LOWER BRACKET
HOLE:
HOLE A = -2.6° TO 2.6°
HOLE B = 1.6° TO 6.8° STEP 4
20°
20° 20° MAX.
MAX. MAX. 2. USE CALIBRATING BOLT
20° TO ADJUST FRAME TO
MAX.
FITS LEG SIZES
DESIRED TAPER STEP 2

UP TO 8-5/8" O.D.

10 1/2" ± TAPER ADJUSTMENT

3. TORQUE LOCKING BOLTS UPPER
TO 100 ft.-lbs.

4. ADVANCE LOCKING NUT

TO POSITIONING PLATE,
THEN TIGHTEN.
33 29/32"

B A 1.6° to 6.8°
143" ±
A -2.6° to 2.6°
LOWER

40" 120"

TOLERANCE NOTES DESCRIPTION

Locations:
12' 6" HEAVY DUTY New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: Engineering Atlanta, GA
V-FRAME ASSEMBLY Support Team: Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030")
W/ 2 STIFF ARMS 1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES & MOUNT PIPES
valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

3 OF 5
ALL OTHER ASSEMBLY (± 0.060") SP1 CSL 1/25/2017 VFA12-WLL-30120

PAGE
A UPDATED BCAM VERSION 1 TO BCAM VERSION 2 SP1 CSL 7/2/2018
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
REV DESCRIPTION OF REVISIONS CPD BY DATE THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT

REVISION HISTORY
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 5/3/2018 VFA12-WLL-30120
 13 36 X2
9
35 X2
10
27 34 X2

31 30 32 OR 33

30 31 32
23 34 X2
29
18
26 OR 20 OR 21 30 35 X2
17
14
12
DETAIL A 31 36 X2
31 16
OR
30 15
11
F 28 DETAIL B
13
A
B

D
5
4 19

30 X2
22
X2 DETAIL C 31 X2
24
30
E X2
29 2 DETAIL D
31
6
C G 30
31 31
30
15 16 17 18 31 31 X2
28
30 31

29 X2 29 X3

26 12 31

7/16" LUG HOLES

9/16" SLOTTED HOLE
REVIEW CARRIER STANDARDS FOR FOR EQUIPMENT PIPE U-BOLT
PROPER SURFACE PREPARTION AND 19
ASSEMBLY OF ELECTRICAL CONNECTIONS 12
30 X2
3 DETAIL E 6
23 30 31
31 X2 DETAIL F X2 X2

DETAIL G

TOLERANCE NOTES DESCRIPTION

Locations:
12' 6" HEAVY DUTY New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: Engineering Atlanta, GA
V-FRAME ASSEMBLY Support Team: Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030")
W/ 2 STIFF ARMS 1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES & MOUNT PIPES
valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

4 OF 5
ALL OTHER ASSEMBLY (± 0.060") SP1 CSL 1/25/2017 VFA12-WLL-30120

PAGE
A UPDATED BCAM VERSION 1 TO BCAM VERSION 2 SP1 CSL 7/2/2018
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
REV DESCRIPTION OF REVISIONS CPD BY DATE THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT

REVISION HISTORY
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 5/3/2018 VFA12-WLL-30120
 EQUIPMENT PIPE AND HARDWARE
UNISTRUT AND HARDWARE
SOLD SEPARATELY.
SOLD SEPARATELY.
REQUIRES 1/2" HARDWARE
REQUIRES 3/8" HARDWARE AND 2-3/8" TO 4-1/2" O.D. PIPE

TOLERANCE NOTES DESCRIPTION

Locations:
12' 6" HEAVY DUTY New York, NY
TOLERANCES ON DIMENSIONS, UNLESS OTHERWISE NOTED ARE: Engineering Atlanta, GA
V-FRAME ASSEMBLY Support Team: Los Angeles, CA
SAWED, SHEARED AND GAS CUT EDGES (± 0.030")
W/ 2 STIFF ARMS 1-888-753-7446 Plymouth, IN
DRILLED AND GAS CUT HOLES (± 0.030") - NO CONING OF HOLES Salem, OR
LASER CUT EDGES AND HOLES (± 0.010") - NO CONING OF HOLES & MOUNT PIPES
valmont Dallas, TX
BENDS ARE ± 1/2 DEGREE
ALL OTHER MACHINING (± 0.030") CPD NO. DRAWN BY ENG. APPROVAL PART NO.

5 OF 5
ALL OTHER ASSEMBLY (± 0.060") SP1 CSL 1/25/2017 VFA12-WLL-30120

PAGE
A UPDATED BCAM VERSION 1 TO BCAM VERSION 2 SP1 CSL 7/2/2018
PROPRIETARY NOTE: CLASS SUB DRAWING USAGE CHECKED BY DWG. NO.
REV DESCRIPTION OF REVISIONS CPD BY DATE THE DATA AND TECHNIQUES CONTAINED IN THIS DRAWING ARE PROPRIETARY INFORMATION OF VALMONT

REVISION HISTORY
INDUSTRIES AND CONSIDERED A TRADE SECRET. ANY USE OR DISCLOSURE WITHOUT THE CONSENT OF
VALMONT INDUSTRIES IS STRICTLY PROHIBITED.
87 02 CUSTOMER BMC 5/3/2018 VFA12-WLL-30120