1.

INTRODUCTION
The document presents the structural analysis and design to be used in the structural
design of proposed structures. The criteria presented specific information on the
description of the building and its structural system, codes, standards and references,
loading criteria, materials, and modeling and the prescribed analysis and design
procedures.

2. GENERAL CODES AND REFERENCES

The design references for the proposed project:
a) ACI- American Concrete Institute
b) AISC- American Institute of Steel Construction
c) ASCE- American Society of Civil Engineers 2010
d) UBC 97- Uniform Building Code 1997
e) ASTM- American Society for Testing Materials
f) ASEP- Association of Structural Engineers of the Philippines Handbook of
Structural Steel Shapes and Sections
g) NSCP- National Structural Code of the Philippines 2015
h)
3. GRAVITY DESIGN LOADS
The following loads are in addition to the self-weight of the structure. The minimum
loading requirements have been taken from NSCP 2015.

Super Imposed Dead Loads Live Loads

Materials Loadings Area/Location Loadings

Reinforced Concrete 24.00kN/m3 Residential 1.90kPa

Structural Steel 77.30kN/m3 Stair 4.80kPa

Gypsum Board (12mm) 0.10kPa Balcony 4.80kPa

Mechanical Duct Allowance 0.20kPa Roof 1.00kPa

Suspended Steel Channel
0.10kPa
System
Ceramic Tile Finish 1.10kPa
Movable Partition 0.24kPa
25mm Concrete Topping 0.60kPa
4. WIND DESIGN LOADS

Wind load is in accordance with NSCP requirements:

Wind Design Criteria:

a) Basic Wind Speed: 260kph (162mph)

b) Exposure: B
c) Importance Factor: 1.0
d) Enclosure Classification: Enclosed
e) Velocity Pressure Coefficient (qz): Varies per height according to building
code.

Pasig
5. SEISMIC DESIGN LOADS

Seismic Zone Factor 0.40 (Zone 4)

Seismic Source Type Type A

Soil Profile Type SD

Importance Factor, I 1.00

Nearest Fault West Valley Fault

Distance From Nearest Fault 1.00km

Near Source Factor, Na 1.50

Near Source Factor, Nv 2.00

Over-Strength Factor, R 8.50

*Static Force Base Shear

*The total design base shear in a given directions
shall be determined from the following equation:
𝐂𝐯𝑰
V= W
𝐑𝐓
*The total design base shear need not
exceed the following:
𝟐.𝟓𝐂𝐚𝑰
V= W ( Maximum Value)
𝐑
*The total design base shear shall not be
less than the following:
V=0.11CaI W ( Minimum Value)
*In addition, for Seismic Zone 4, the total
base shear shall
also not be less that the following:
𝟎.𝟖𝟎𝐙𝐍𝐯𝑰
V= W
𝐑
6. LOAD COMBINATIONS
Service Load Combinations
Serv 101 DL+LL
Serv 102 0.75DL + 0.56LL + 0.34Wx
Serv 103 0.75DL + 0.56LL + 0.34Wy
Serv 104 0.75DL + 0.56LL + 0.40EQx (+)
Serv 105 0.75DL + 0.56LL + 0.40EQx (-)
Serv 106 0.75DL + 0.56LL + 0.40EQy (+)
Serv 107 0.75DL + 0.56LL + 0.40EQy (-)
Serv 108 0.45DL + 0.45Wx
Serv 109 0.45DL + 0.45Wy
Serv 110 0.45DL + 0.54EQx (+)
Serv 111 0.45DL + 0.54EQx (-)
Serv 112 0.45DL + 0.54EQy (+)
Serv 113 0.45DL + 0.54EQy (-)
Serv 114 0.75DL + 0.75LL
Serv 115 0.75DL + 0.75LL + 0.45Wx
Serv 116 0.75DL + 0.75LL + 0.45Wy
Serv 117 0.75DL + 0.75LL + 0.54EQx (+)
Serv 118 0.75DL + 0.75LL + 0.54EQx (-)
Serv 118 0.75DL + 0.75LL + 0.54EQy (+)
Serv 120 0.75DL + 0.75LL + 0.54EQy (-)

Ultimate Load Combinations

Ult 101 1.4DL
Ult 102 1.2DL + 1.6LL
Ult 103 1.2DL + f1LL
Ult 104 1.2DL + 1.6LL + 0.50Wx
Ult 105 1.2DL + 1.6LL + 0.50Wy
Ult 106 1.2DL + Wx + f1LL
Ult 107 1.2DL + Wy + f1LL
Ult 108 (1.20 + 0.50CaI) DL + f1LL + EQx (+)
Ult 109 (1.20 + 0.50CaI) DL + f1LL + EQx (-)
Ult 110 (1.20 + 0.50CaI) DL + f1LL + EQy (+)
Ult 111 (1.20 + 0.50CaI) DL + f1LL + EQy (-)
Ult 112 0.90DL + Wx
Ult 113 0.90DL + Wy
Ult 114 (0.90 + 0.50CaI) DL + f1LL + EQx (+)
Ult 115 (0.90 + 0.50CaI) DL + f1LL + EQx (-)
Ult 116 (0.90 + 0.50CaI) DL + f1LL + EQy (+)
Ult 117 (0.90 + 0.50CaI) DL + f1LL + EQy (-)

*f1 = 1.00, if LL>4.80kPa

= 0.50, if LL<4.80kPa
9. MATERIAL SPECIFICATIONS
9.1 Concrete
Compressive strength shall br measures at 28days, cylinder specimen (f’c) shall be
used based on the structural member as follows:
Foundation 6000psi (41.36MPa)
Column 6000psi (41.36MPa)
Girder/Beam 6000psi (41.36MPa)
Suspended Slab 6000psi (41.36MPa)
Slab On Grade 3000psi (20.70MPa)
Concrete Stair 6000psi (41.36MPa)

If not specifically indicated on the drawings, clear concrete cover at the outmost
reinforcing bar shall be as follows:

• All concrete in contact with soil and where applicable 75mm

• All above grade concrete exposed to weathering 50mm

• All above grade concrete protected from weathering

Beams, Column, Shearwall 40mm
Slabs 40mm

9.2 Reinforcing Steel

Reinforcing steel shall be in accordance with ASTM A615. The yield strength of the
reinforcing steel (fy) to be used is as follows:
Rebar 10mm Ø and Below Grade60 (414MPa)
Rebar 16mm Ø and Below Grade60 (414MPa)

9.3 Structural Steel

Structural Steel grade will be ASTM A36, Fy=248MPa (36ksi)
10. FOUNDATION
Foundations are designed based on the assumed allowable soil bearing capacity of
500kPa at 2.00 meters from the natural grade line.The footing should rest on hard
strata and no footing shall rest on fill.
 FOOTING

SHOWING THICKNESS
SHOWING SOIL BEARING PRESSURE
 Design

Figure 3: Finite element model

6. Design summary
This section provides design information for beams, strips, and punching checks.

6.1. Preferences
Table 24: Design Preferences 01 - Resistance Factors
Table 24: Design Preferences 01 -
Resistance Factors
PhiTen PhiComp PhiShear

0.900000 0.650000 0.750000

Table 25: Design Preferences 02 - Rebar Cover - Slabs

Table 25: Design Preferences 02 - Rebar Cover - Slabs
CoverTop CoverBot BarSize InnerLayer PTCGSTop PTCGSBotE PTCGSBotI SlabType
xt nt
mm mm mm mm mm
15.000 15.000 18 B 25.000 40.000 25.000 Two Way

Table 26: Design Preferences 03 - Rebar Cover - Beams

Table 26: Design Preferences 03 - Rebar Cover - Beams
CoverTop CoverBot BarSizeF BarSizeS PTCGSTop PTCGSBot
mm mm mm mm
40.000 40.000 28 12 50.000 50.000

Table 27: Design Preferences 04 - Prestress Data

Table 27: Design Preferences 04 -
Prestress Data
UserStress InitConcRat LLFraction

No 0.800000 0.500000

6.2. Overwrites
Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 1 of 2
Table 28: Slab Design Overwrites 02 - Finite Element
Based, Part 1 of 2
Area RebarMat

1 CSA-G30.18Gr400
2 CSA-G30.18Gr400
3 CSA-G30.18Gr400
4 CSA-G30.18Gr400
Table 28: Slab Design Overwrites 02 - Finite Element Based, Part 2 of 2
Table 28: Slab Design Overwrites 02 - Finite Element Based,
Part 2 of 2
Area RLLF Design IgnorePT

1 1.000000 Yes No
2 1.000000 Yes No
3 1.000000 Yes No
4 1.000000 Yes No

Table 29: Beam Design Overwrites

Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

W12-W Section 1.000000 No

W13-W Section 1.000000 No
W14-W Section 1.000000 No
W15-W Section 1.000000 No
W16-W Section 1.000000 No
W17-W Section 1.000000 No
W18-W Section 1.000000 No
W19-W Section 1.000000 No
W20-W Section 1.000000 No
W21-W Section 1.000000 No
W22-W Section 1.000000 No
W23-W Section 1.000000 No
W24-W Section 1.000000 No
W25-W Section 1.000000 No
W26-W Section 1.000000 No
W27-W Section 1.000000 No
W28-W Section 1.000000 No
W29-W Section 1.000000 No
W30-W Section 1.000000 No
W31-W Section 1.000000 No
W32-W Section 1.000000 No
W33-W Section 1.000000 No
W34-W Section 1.000000 No
W35-W Section 1.000000 No
W36-W Section 1.000000 No
W37-W Section 1.000000 No
W38-W Section 1.000000 No
W39-W Section 1.000000 No
W40-W Section 1.000000 No
W41-W Section 1.000000 No
W42-W Section 1.000000 No
W43-W Section 1.000000 No
W44-W Section 1.000000 No
W45-W Section 1.000000 No
W46-W Section 1.000000 No
W47-W Section 1.000000 No
W48-W Section 1.000000 No
W49-W Section 1.000000 No
 Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

W50-W Section 1.000000 No

W51-W Section 1.000000 No
W52-W Section 1.000000 No
W53-W Section 1.000000 No
W54-W Section 1.000000 No
W55-W Section 1.000000 No
W56-W Section 1.000000 No
W57-W Section 1.000000 No
W58-W Section 1.000000 No
W59-W Section 1.000000 No
W60-W Section 1.000000 No
W61-W Section 1.000000 No
W62-W Section 1.000000 No
W63-W Section 1.000000 No
W64-W Section 1.000000 No
W65-W Section 1.000000 No
W66-W Section 1.000000 No
W67-W Section 1.000000 No
W68-W Section 1.000000 No
W69-W Section 1.000000 No
W70-W Section 1.000000 No
W71-W Section 1.000000 No
W72-W Section 1.000000 No
W73-W Section 1.000000 No
W74-W Section 1.000000 No
W75-W Section 1.000000 No
W76-W Section 1.000000 No
W77-W Section 1.000000 No
W78-W Section 1.000000 No
W79-W Section 1.000000 No
W80-W Section 1.000000 No
W81-W Section 1.000000 No
W82-W Section 1.000000 No
W83-W Section 1.000000 No
W84-W Section 1.000000 No
W85-W Section 1.000000 No
W86-W Section 1.000000 No
W87-W Section 1.000000 No
W88-W Section 1.000000 No
W89-W Section 1.000000 No
W90-W Section 1.000000 No
W91-W Section 1.000000 No
W92-W Section 1.000000 No
W93-W Section 1.000000 No
W94-W Section 1.000000 No
W95-W Section 1.000000 No
W96-W Section 1.000000 No
W97-W Section 1.000000 No
W98-W Section 1.000000 No
W99-W Section 1.000000 No
W100-W Section 1.000000 No
W101-W Section 1.000000 No
W102-W Section 1.000000 No
W103-W Section 1.000000 No
 Table 29: Beam Design Overwrites
Line CoverType RLLF IgnorePT

W104-W Section 1.000000 No

W105-W Section 1.000000 No
W106-W Section 1.000000 No
W107-W Section 1.000000 No
W108-W Section 1.000000 No
W109-W Section 1.000000 No
W110-W Section 1.000000 No
W111-W Section 1.000000 No
W112-W Section 1.000000 No
W113-W Section 1.000000 No
W114-W Section 1.000000 No
W115-W Section 1.000000 No
W116-W Section 1.000000 No
W117-W Section 1.000000 No
W118-W Section 1.000000 No
W119-W Section 1.000000 No
W120-W Section 1.000000 No
W121-W Section 1.000000 No

Table 30: Punching Shear Design Overwrites 01 - General

Table 30: Punching Shear Design Overwrites 01 - General
Point Check LocType EffDepth ReinfType

4 Program Auto Auto None

Determined
6 Program Auto Auto None
Determined
8 Program Auto Auto None
Determined
10 Program Auto Auto None
Determined
12 Program Auto Auto None
Determined
14 Program Auto Auto None
Determined
16 Program Auto Auto None
Determined
18 Program Auto Auto None
Determined
171 Program Auto Auto None
Determined
192 Program Auto Auto None
Determined
213 Program Auto Auto None
Determined
215 Program Auto Auto None
Determined
217 Program Auto Auto None
Determined
219 Program Auto Auto None
Determined
221 Program Auto Auto None
Determined
 Table 30: Punching Shear Design Overwrites 01 - General
Point Check LocType EffDepth ReinfType

223 Program Auto Auto None

Determined
225 Program Auto Auto None
Determined
226 Program Auto Auto None
Determined
228 Program Auto Auto None
Determined
231 Program Auto Auto None
Determined
233 Program Auto Auto None
Determined
235 Program Auto Auto None
Determined
237 Program Auto Auto None
Determined
239 Program Auto Auto None
Determined
241 Program Auto Auto None
Determined
243 Program Auto Auto None
Determined
245 Program Auto Auto None
Determined
247 Program Auto Auto None
Determined
249 Program Auto Auto None
Determined
251 Program Auto Auto None
Determined
253 Program Auto Auto None
Determined
254 Program Auto Auto None
Determined
256 Program Auto Auto None
Determined
258 Program Auto Auto None
Determined
260 Program Auto Auto None
Determined
409 Program Auto Auto None
Determined
410 Program Auto Auto None
Determined

6.3. Slab design

6.4. Beam design

6.5. Punching check/design

Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 1 of 3

Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 1 of 3
Point GlobalX GlobalY Location Perimeter Depth Status Ratio
m m mm mm
4 4.00000 29.30000 Corner 6267.500 1167.000 OK 0.013708
6 33.20000 29.30000 Corner 6267.500 1167.000 OK 0.011239
8 4.00000 4.60000 Corner 5267.500 1167.000 OK 0.013024
10 33.20000 4.60000 Corner 6067.500 1167.000 OK 0.013828
12 4.00000 15.60000 Edge 8934.500 1167.000 OK 0.010011
14 4.00000 19.60000 Edge 8934.500 1167.000 OK 0.009900
16 33.20000 15.60000 Edge 8534.500 1167.000 OK 0.009756
18 33.20000 19.60000 Edge 8534.500 1167.000 OK 0.009048
171 17.00000 4.60000 Corner 6842.500 1167.000 OK 0.011626
192 20.00000 4.60000 Corner 7942.500 1167.000 OK 0.011669
213 0.00000 33.80000 Not
Calculated
215 35.80000 0.00000 Not
Calculated
217 35.80000 4.60000 Corner 3842.500 1167.000 OK 0.012285
219 35.80000 15.60000 Edge 13284.500 1167.000 OK 0.009858
221 35.80000 19.60000 Edge 13284.500 1167.000 OK 0.009120
223 35.80000 29.30000 Corner 3442.500 1167.000 OK 0.008935
225 35.80000 33.80000 Not
Calculated
226 35.80000 24.45000 Corner 8292.500 1167.000 OK 0.035793
228 35.80000 10.10000 Edge 13284.500 1167.000 OK 0.012289
231 0.00000 4.60000 Not
Calculated
233 0.00000 15.60000 Not
Calculated
235 0.00000 19.60000 Not
Calculated
237 0.00000 29.30000 Not
Calculated
239 4.00000 33.80000 Not
Calculated
241 17.00000 33.80000 Not
Calculated
243 20.00000 33.80000 Not
Calculated
245 33.20000 33.80000 Not
Calculated
247 4.00000 0.00000 Not
Calculated
249 17.00000 0.00000 Not
Calculated
251 20.00000 0.00000 Not
Calculated
253 33.20000 0.00000 Not
Calculated
254 10.50000 33.80000 Not
Calculated
 Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 1 of 3
Point GlobalX GlobalY Location Perimeter Depth Status Ratio
m m mm mm
256 26.60000 33.80000 Not
Calculated
258 10.50000 0.00000 Not
Calculated
260 26.60000 0.00000 Not
Calculated
409 0.00000 24.45000 Not
Calculated
410 0.00000 10.10000 Not
Calculated

Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 2 of 3

Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 2 of 3
Point Combo Vu Gamma_v2 Gamma_v3 ShrStrMax Mu2 ShrStrCap
kN N/mm2 kN-m N/mm2
4 ULT1 1.40DL 97.464 0.400000 0.419331 0.021963 -3.7160 1.602197
6 ULT1 1.40DL 98.037 0.400000 0.451406 0.018008 7.5112 1.602197
8 ULT1 1.40DL 70.296 0.400000 0.413758 0.020867 -58.4030 1.602197
10 ULT1 1.40DL 89.953 0.400000 0.411933 0.022155 -75.0566 1.602197
12 ULT1 1.40DL 133.697 0.318857 0.487027 0.016039 -3.111E-012 1.602197
14 ULT1 1.40DL 132.091 0.318857 0.487027 0.015862 -4.603E-013 1.602197
16 ULT1 1.40DL 120.224 0.325125 0.479857 0.015631 8.528E-012 1.602197
18 ULT1 1.40DL 110.749 0.325125 0.479857 0.014497 -6.449E-012 1.602197
171 ULT1 1.40DL 118.495 0.400000 0.436709 0.018627 31.3525 1.602197
192 ULT1 1.40DL 135.227 0.400000 0.467236 0.018697 34.7187 1.602197
213
215
217 ULT1 1.40DL 34.259 0.503618 0.400000 0.019684 -30.5682 1.602197
219 ULT1 1.40DL 172.781 0.269692 0.546181 0.015795 2.587E-012 1.602197
221 ULT1 1.40DL 158.997 0.269692 0.546181 0.014612 -1.391E-012 1.602197
223 ULT1 1.40DL 24.958 0.483449 0.400000 0.014316 23.1375 1.602197
225
226 ULT1 1.40DL 100.840 0.623230 0.400000 0.057348 78.1343 1.602197
228 ULT1 1.40DL 213.926 0.269692 0.546181 0.019690 -9.877E-012 1.602197
231
233
235
237
239
241
243
245
247
249
251
253
254
256
258
260
409
410
Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 3 of 3
Table 31: Concrete Slab Design 02 - Punching Shear Data, Part 3 of 3
Point Mu3 ReinfType UnbalMu2 UnbalMu3 NumRails StudPerRail
kN-m kN-m kN-m
4 -77.1378 None -1.4864 -32.3463
6 -49.7608 None 3.0045 -22.4623
8 20.9491 None -23.3612 8.6679
10 20.6697 None -30.0226 8.5145
12 -46.8125 None -9.919E-013 -22.7990
14 -46.4703 None -1.468E-013 -22.6323
16 47.6296 None 2.773E-012 22.8554
18 45.1903 None -2.097E-012 21.6849
171 10.5151 None 12.5410 4.5921
192 -14.1538 None 13.8875 -6.6132
213 None
215 None
217 -24.8172 None -15.3947 -9.9269
219 139.5971 None 6.976E-013 76.2453
221 130.7622 None -3.750E-013 71.4199
223 -17.7997 None 11.1858 -7.1199
225 None
226 -80.4018 None 48.6957 -32.1607
228 176.8517 None -2.664E-012 96.5931
231 None
233 None
235 None
237 None
239 None
241 None
243 None
245 None
247 None
249 None
251 None
253 None
254 None
256 None
258 None
260 None
409 None
410 None
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 4
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 4 m
Global Y-Coordinate = 29.3 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 6267.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 6.491E+012 mm4
Section Inertia I33 = 9.417E+012 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.419331
Moment Mu2 = -3.716 kN-m
Moment Mu3= -77.1378 kN-m
Shear Force = 97.464 kN
Unbalanced Moment Mu2 = -1.4864 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 6
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 33.2 m
Global Y-Coordinate = 29.3 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 6267.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 4.518E+012 mm4
Section Inertia I33 = 1.203E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.451406
Moment Mu2 = 7.5112 kN-m
Moment Mu3= -49.7608 kN-m
Shear Force = 98.037 kN
Unbalanced Moment Mu2 = 3.0045 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 8
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 4 m
Global Y-Coordinate = 4.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 5267.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 4.181E+012 mm4
Section Inertia I33 = 5.434E+012 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.413758
Moment Mu2 = -58.403 kN-m
Moment Mu3= 20.9491 kN-m
Shear Force = 70.296 kN
Unbalanced Moment Mu2 = -23.3612 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 10
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 33.2 m
Global Y-Coordinate = 4.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 6067.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 6.385E+012 mm4
Section Inertia I33 = 8.035E+012 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.411933
Moment Mu2 = -75.0566 kN-m
Moment Mu3= 20.6697 kN-m
Shear Force = 89.953 kN
Unbalanced Moment Mu2 = -30.0226 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 12
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 4 m
Global Y-Coordinate = 15.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 8934.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 7.3E+012 mm4
Section Inertia I33 = 1.521E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.318857 Column Punching Perimeter
Gamma_v3 = 0.487027
Moment Mu2 = -3.111E-012 kN-m
Moment Mu3= -46.8125 kN-m
Shear Force = 133.697 kN
Unbalanced Moment Mu2 = -9.919E-013 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 14
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 4 m
Global Y-Coordinate = 19.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 8934.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 7.3E+012 mm4
Section Inertia I33 = 1.521E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.318857 Column Punching Perimeter
Gamma_v3 = 0.487027
Moment Mu2 = -4.603E-013 kN-m
Moment Mu3= -46.4703 kN-m
Shear Force = 132.091 kN
Unbalanced Moment Mu2 = -1.468E-013 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 16
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 33.2 m
Global Y-Coordinate = 15.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 8534.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 6.935E+012 mm4
Section Inertia I33 = 1.311E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.325125 Column Punching Perimeter
Gamma_v3 = 0.479857
Moment Mu2 = 8.528E-012 kN-m
Moment Mu3= 47.6296 kN-m
Shear Force = 120.224 kN
Unbalanced Moment Mu2 = 2.773E-012 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 18
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 33.2 m
Global Y-Coordinate = 19.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 8534.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 6.935E+012 mm4
Section Inertia I33 = 1.311E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.325125 Column Punching Perimeter
Gamma_v3 = 0.479857
Moment Mu2 = -6.449E-012 kN-m
Moment Mu3= 45.1903 kN-m
Shear Force = 110.749 kN
Unbalanced Moment Mu2 = -2.097E-012 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 171
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 17 m
Global Y-Coordinate = 4.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 6842.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 6.906E+012 mm4
Section Inertia I33 = 1.399E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.436709
Moment Mu2 = 31.3525 kN-m
Moment Mu3= 10.5151 kN-m
Shear Force = 118.495 kN
Unbalanced Moment Mu2 = 12.541 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 192
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 20 m
Global Y-Coordinate = 4.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 7942.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 7.329E+012 mm4
Section Inertia I33 = 2.67E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.4 Column Punching Perimeter
Gamma_v3 = 0.467236
Moment Mu2 = 34.7187 kN-m
Moment Mu3= -14.1538 kN-m
Shear Force = 135.227 kN
Unbalanced Moment Mu2 = 13.8875 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 217
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 4.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 3842.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 3.936E+012 mm4
Section Inertia I33 = 6.218E+011 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.503618 Column Punching Perimeter
Gamma_v3 = 0.4
Moment Mu2 = -30.5682 kN-m
Moment Mu3= -24.8172 kN-m
Shear Force = 34.259 kN
Unbalanced Moment Mu2 = -15.3947 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 219
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 15.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 13284.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 1.126E+013 mm4
Section Inertia I33 = 5.349E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.269692 Column Punching Perimeter
Gamma_v3 = 0.546181
Moment Mu2 = 2.587E-012 kN-m
Moment Mu3= 139.5971 kN-m
Shear Force = 172.781 kN
Unbalanced Moment Mu2 = 6.976E-013 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 221
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 19.6 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 13284.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 1.126E+013 mm4
Section Inertia I33 = 5.349E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.269692 Column Punching Perimeter
Gamma_v3 = 0.546181
Moment Mu2 = -1.391E-012 kN-m
Moment Mu3= 130.7622 kN-m
Shear Force = 158.997 kN
Unbalanced Moment Mu2 = -3.75E-013 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 223
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 29.3 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 3442.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 2.631E+012 mm4
Section Inertia I33 = 6.059E+011 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.483449 Column Punching Perimeter
Gamma_v3 = 0.4
Moment Mu2 = 23.1375 kN-m
Moment Mu3= -17.7997 kN-m
Shear Force = 24.958 kN
Unbalanced Moment Mu2 = 11.1858 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 226
Column Shape = Rectangular
Column Location = Corner
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 24.45 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 8292.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 5.105E+013 mm4
Section Inertia I33 = 6.953E+011 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.62323 Column Punching Perimeter
Gamma_v3 = 0.4
Moment Mu2 = 78.1343 kN-m
Moment Mu3= -80.4018 kN-m
Shear Force = 100.84 kN
Unbalanced Moment Mu2 = 48.6957 kN-m
 ACI 318-14 Punching Shear Check & Design

Geometric Properties

Combination = 74
Point Label = 228
Column Shape = Rectangular
Column Location = Edge
Global X-Coordinate = 35.8 m
Global Y-Coordinate = 10.1 m

Load Punching Check

Avg. Eff. Slab Thickness = 1167 mm

Eff. Punching Perimeter = 13284.5 mm
Cover = 33 mm
Conc. Comp. Strength = 41.36855 N/mm2
Reinforcement Ratio = 0.0000
Section Inertia I22 = 1.126E+013 mm4
Section Inertia I33 = 5.349E+013 mm4
Section Inertia I23 = 0 mm4
Gamma_v2 = 0.269692 Column Punching Perimeter
Gamma_v3 = 0.546181
Moment Mu2 = -9.877E-012 kN-m
Moment Mu3= 176.8517 kN-m
Shear Force = 213.926 kN
Unbalanced Moment Mu2 = -2.664E-012 kN-m
 DESIGN OF SLAB - GS1 / DS1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0064
Thickness Used, t = 100 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.06
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.25
øBar = 12 mm kd = 18.59 mm
Es = 200000 Mpa Yt = t - kd = 81.41 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 4.08 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 5.35E+05 mm⁴
Effective Depth, d = 74 mm
 Mcr    Mcr 
3 3
 =
3.37E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
8.33E+07 mm⁴
8.33E+07 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.35 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 8.75 kN/m Actual deflection
δact = δDL + δLL = 0.55 mm 13%
C. DIAGRAM Moment Inertia, Ix = 8.33E+07 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.39 mm
δLL = 5Wll L⁴/384EcIx = 0.16 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@240mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@240mm

Left Right
Mu 3.50 3.50 kNm ø12@240mm
Ru = Mu/(øbd²) 0.71 0.71
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0026 0.0026
As = ρbd 192.3 192.3 mm²
S = 1000/As/Ab 588 588 mm
S = 3t → 300 300 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@240mm Top Bars at Left Supports
Say Spacing 240 240 mm Therefore Provide ø12@240mm Bottom Bars at Mid Span
Therefore Provide ø12@240mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.19 kNm
Service Total, Mt 1.66 kNm
Mu 2.19 kNm
Ru = Mu/(øbd²) 0.4436
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0016
As = ρbd 148.0 mm²
S = 1000/As/Ab 764 mm
S = 3t 300 mm ←
S= 450 450 mm
Say Spacing 240 mm
 DESIGN OF SLAB - GS2 / DS2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0069
Thickness Used, t = 100 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.04
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.26
øBar = 12 mm kd = 19.29 mm
Es = 200000 Mpa Yt = t - kd = 80.71 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 4.12 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 5.98E+05 mm⁴
Effective Depth, d = 74 mm
 Mcr    Mcr 
3 3
 =
3.46E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
8.33E+07 mm⁴
8.33E+07 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.35 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 8.75 kN/m Actual deflection
δact = δDL + δLL = 0.55 mm 13%
C. DIAGRAM Moment Inertia, Ix = 8.33E+07 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.39 mm
δLL = 5Wll L⁴/384EcIx = 0.16 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@220mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@220mm

Left Right
Mu 3.50 3.50 kNm ø12@250mm
Ru = Mu/(øbd²) 0.71 0.71
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0026 0.0026
As = ρbd 192.3 192.3 mm²
S = 1000/As/Ab 588 588 mm
S = 3t → 300 300 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@220mm Top Bars at Left Supports
Say Spacing 220 250 mm Therefore Provide ø12@220mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.19 kNm
Service Total, Mt 1.66 kNm
Mu 2.19 kNm
Ru = Mu/(øbd²) 0.4436
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0016
As = ρbd 148.0 mm²
S = 1000/As/Ab 764 mm
S = 3t 300 mm ←
S= 450 450 mm
Say Spacing 220 mm
 DESIGN OF SLAB - GS3

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0075
Thickness Used, t = 110 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.02
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.27
øBar = 12 mm kd = 22.59 mm
Es = 200000 Mpa Yt = t - kd = 87.41 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 5.06 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 9.61E+05 mm⁴
Effective Depth, d = 84 mm
 Mcr    Mcr 
3 3
 =
7.38E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.11E+08 mm⁴
1.11E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.59 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.03 kN/m Actual deflection
δact = δDL + δLL = 0.43 mm 10%
C. DIAGRAM Moment Inertia, Ix = 1.11E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.31 mm
δLL = 5Wll L⁴/384EcIx = 0.12 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@180mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@180mm

Left Right
Mu 3.61 3.61 kNm ø12@250mm
Ru = Mu/(øbd²) 0.57 0.57
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0021 0.0021
As = ρbd 174.5 174.5 mm²
S = 1000/As/Ab 648 648 mm
S = 3t → 330 330 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@180mm Top Bars at Left Supports
Say Spacing 180 250 mm Therefore Provide ø12@180mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.25 kNm
Service Total, Mt 1.72 kNm
Mu 2.26 kNm
Ru = Mu/(øbd²) 0.3554
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0013
As = ρbd 168.0 mm²
S = 1000/As/Ab 673 mm
S = 3t 330 mm ←
S= 450 450 mm
Say Spacing 180 mm
 DESIGN OF SLAB - GS4 / DS4

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0075
Thickness Used, t = 120 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.02
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.27
øBar = 12 mm kd = 25.34 mm
Es = 200000 Mpa Yt = t - kd = 94.66 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 6.07 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.36E+06 mm⁴
Effective Depth, d = 94 mm
 Mcr    Mcr 
3 3
 =
1.44E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.44E+08 mm⁴
1.44E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.83 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.31 kN/m Actual deflection
δact = δDL + δLL = 0.34 mm 8%
C. DIAGRAM Moment Inertia, Ix = 1.44E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.25 mm
δLL = 5Wll L⁴/384EcIx = 0.09 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@160mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@160mm

Left Right
Mu 3.72 3.72 kNm ø12@250mm
Ru = Mu/(øbd²) 0.47 0.47
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0017 0.0017
As = ρbd 188.0 188.0 mm²
S = 1000/As/Ab 602 602 mm
S = 3t → 360 360 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@160mm Top Bars at Left Supports
Say Spacing 160 250 mm Therefore Provide ø12@160mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.31 kNm
Service Total, Mt 1.78 kNm
Mu 2.33 kNm
Ru = Mu/(øbd²) 0.2927
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0011
As = ρbd 188.0 mm²
S = 1000/As/Ab 602 mm
S = 3t 360 mm ←
S= 450 450 mm
Say Spacing 160 mm
 DESIGN OF SLAB - GS5 / DS5

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0083
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.99
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.28
øBar = 12 mm kd = 31.98 mm
Es = 200000 Mpa Yt = t - kd = 108.02 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.44 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.73E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
4.74E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.23 mm 5%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.17 mm
δLL = 5Wll L⁴/384EcIx = 0.06 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@120mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 3.95 3.95 kNm ø12@250mm
Ru = Mu/(øbd²) 0.34 0.34
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0012 0.0012
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.42 kNm
Service Total, Mt 1.90 kNm
Mu 2.47 kNm
Ru = Mu/(øbd²) 0.2111
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0008
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - DS-6

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0072
Thickness Used, t = 130 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.03
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.27
øBar = 12 mm kd = 27.61 mm
Es = 200000 Mpa Yt = t - kd = 102.39 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 7.13 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.75E+06 mm⁴
Effective Depth, d = 104 mm
 Mcr    Mcr 
3 3
 =
2.60E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.83E+08 mm⁴
1.83E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.06 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.59 kN/m Actual deflection
δact = δDL + δLL = 0.28 mm 7%
C. DIAGRAM Moment Inertia, Ix = 1.83E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.21 mm
δLL = 5Wll L⁴/384EcIx = 0.07 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@150mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@150mm

Left Right
Mu 3.84 3.84 kNm ø12@250mm
Ru = Mu/(øbd²) 0.39 0.39
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0014 0.0014
As = ρbd 208.0 208.0 mm²
S = 1000/As/Ab 544 544 mm
S = 3t → 390 390 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@150mm Top Bars at Left Supports
Say Spacing 150 250 mm Therefore Provide ø12@150mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.37 kNm
Service Total, Mt 1.84 kNm
Mu 2.40 kNm
Ru = Mu/(øbd²) 0.2464
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0009
As = ρbd 208.0 mm²
S = 1000/As/Ab 544 mm
S = 3t 390 mm ←
S= 450 450 mm
Say Spacing 150 mm
 DESIGN OF SLAB - RS1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0072
Thickness Used, t = 130 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.03
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.27
øBar = 12 mm kd = 27.61 mm
Es = 200000 Mpa Yt = t - kd = 102.39 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 7.13 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.75E+06 mm⁴
Effective Depth, d = 104 mm
 Mcr    Mcr 
3 3
 =
2.60E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.83E+08 mm⁴
1.83E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.06 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.59 kN/m Actual deflection
δact = δDL + δLL = 0.28 mm 7%
C. DIAGRAM Moment Inertia, Ix = 1.83E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.21 mm
δLL = 5Wll L⁴/384EcIx = 0.07 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@150mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@150mm

Left Right
Mu 3.84 3.84 kNm ø12@220mm
Ru = Mu/(øbd²) 0.39 0.39
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0014 0.0014
As = ρbd 208.0 208.0 mm²
S = 1000/As/Ab 544 544 mm
S = 3t → 390 390 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@150mm Top Bars at Left Supports
Say Spacing 150 220 mm Therefore Provide ø12@150mm Bottom Bars at Mid Span
Therefore Provide ø12@220mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.37 kNm
Service Total, Mt 1.84 kNm
Mu 2.40 kNm
Ru = Mu/(øbd²) 0.2464
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0009
As = ρbd 208.0 mm²
S = 1000/As/Ab 544 mm
S = 3t 390 mm ←
S= 450 450 mm
Say Spacing 150 mm
 DESIGN OF SLAB - RS2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0076
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.01
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.27
øBar = 12 mm kd = 30.92 mm
Es = 200000 Mpa Yt = t - kd = 109.08 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.36 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.46E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
4.61E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.23 mm 5%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.17 mm
δLL = 5Wll L⁴/384EcIx = 0.06 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@130mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@130mm

Left Right
Mu 3.95 3.95 kNm ø12@220mm
Ru = Mu/(øbd²) 0.34 0.34
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0012 0.0012
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@130mm Top Bars at Left Supports
Say Spacing 130 220 mm Therefore Provide ø12@130mm Bottom Bars at Mid Span
Therefore Provide ø12@220mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.42 kNm
Service Total, Mt 1.90 kNm
Mu 2.47 kNm
Ru = Mu/(øbd²) 0.2111
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0008
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 130 mm
 DESIGN OF SLAB - RS3

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0071
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.03
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.26
øBar = 12 mm kd = 29.97 mm
Es = 200000 Mpa Yt = t - kd = 110.03 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.29 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.24E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
4.49E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.23 mm 5%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.17 mm
δLL = 5Wll L⁴/384EcIx = 0.06 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@140mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@140mm

Left Right
Mu 3.95 3.95 kNm ø12@250mm
Ru = Mu/(øbd²) 0.34 0.34
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0012 0.0012
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@140mm Top Bars at Left Supports
Say Spacing 140 250 mm Therefore Provide ø12@140mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.42 kNm
Service Total, Mt 1.90 kNm
Mu 2.47 kNm
Ru = Mu/(øbd²) 0.2111
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0008
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 140 mm
 DESIGN OF SLAB - S1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0085
Thickness Used, t = 100 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.98
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.28
øBar = 12 mm kd = 20.99 mm
Es = 200000 Mpa Yt = t - kd = 79.01 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 4.21 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 7.71E+05 mm⁴
Effective Depth, d = 74 mm
 Mcr    Mcr 
3 3
 =
3.68E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
8.33E+07 mm⁴
8.33E+07 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.35 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 8.75 kN/m Actual deflection
δact = δDL + δLL = 0.55 mm 13%
C. DIAGRAM Moment Inertia, Ix = 8.33E+07 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.39 mm
δLL = 5Wll L⁴/384EcIx = 0.16 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@180mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@180mm

Left Right
Mu 3.50 3.50 kNm ø12@250mm
Ru = Mu/(øbd²) 0.71 0.71
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0026 0.0026
As = ρbd 192.3 192.3 mm²
S = 1000/As/Ab 588 588 mm
S = 3t → 300 300 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@180mm Top Bars at Left Supports
Say Spacing 180 250 mm Therefore Provide ø12@180mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.19 kNm
Service Total, Mt 1.66 kNm
Mu 2.19 kNm
Ru = Mu/(øbd²) 0.4436
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0016
As = ρbd 148.0 mm²
S = 1000/As/Ab 764 mm
S = 3t 300 mm ←
S= 450 450 mm
Say Spacing 180 mm
 DESIGN OF SLAB - S2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0066
Thickness Used, t = 100 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.05
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.26
øBar = 12 mm kd = 18.93 mm
Es = 200000 Mpa Yt = t - kd = 81.07 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 4.10 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 5.65E+05 mm⁴
Effective Depth, d = 74 mm
 Mcr    Mcr 
3 3
 =
3.41E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
8.33E+07 mm⁴
8.33E+07 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.35 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 8.75 kN/m Actual deflection
δact = δDL + δLL = 0.55 mm 13%
C. DIAGRAM Moment Inertia, Ix = 8.33E+07 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.39 mm
δLL = 5Wll L⁴/384EcIx = 0.16 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@230mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@230mm

Left Right
Mu 3.50 3.50 kNm ø12@250mm
Ru = Mu/(øbd²) 0.71 0.71
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0026 0.0026
As = ρbd 192.3 192.3 mm²
S = 1000/As/Ab 588 588 mm
S = 3t → 300 300 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@230mm Top Bars at Left Supports
Say Spacing 230 250 mm Therefore Provide ø12@230mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.19 kNm
Service Total, Mt 1.66 kNm
Mu 2.19 kNm
Ru = Mu/(øbd²) 0.4436
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0016
As = ρbd 148.0 mm²
S = 1000/As/Ab 764 mm
S = 3t 300 mm ←
S= 450 450 mm
Say Spacing 230 mm
 DESIGN OF SLAB - S3

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0059
Thickness Used, t = 110 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.08
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.24
øBar = 12 mm kd = 20.35 mm
Es = 200000 Mpa Yt = t - kd = 89.65 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 4.93 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 7.02E+05 mm⁴
Effective Depth, d = 84 mm
 Mcr    Mcr 
3 3
 =
6.85E+09 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.11E+08 mm⁴
1.11E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.59 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.03 kN/m Actual deflection
δact = δDL + δLL = 0.43 mm 10%
C. DIAGRAM Moment Inertia, Ix = 1.11E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.31 mm
δLL = 5Wll L⁴/384EcIx = 0.12 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@230mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@230mm

Left Right
Mu 3.61 3.61 kNm ø12@250mm
Ru = Mu/(øbd²) 0.57 0.57
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0021 0.0021
As = ρbd 174.5 174.5 mm²
S = 1000/As/Ab 648 648 mm
S = 3t → 330 330 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@230mm Top Bars at Left Supports
Say Spacing 230 250 mm Therefore Provide ø12@230mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.25 kNm
Service Total, Mt 1.72 kNm
Mu 2.26 kNm
Ru = Mu/(øbd²) 0.3554
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0013
As = ρbd 168.0 mm²
S = 1000/As/Ab 673 mm
S = 3t 330 mm ←
S= 450 450 mm
Say Spacing 230 mm
 DESIGN OF SLAB - S4

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0060
Thickness Used, t = 120 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.08
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.25
øBar = 12 mm kd = 23.04 mm
Es = 200000 Mpa Yt = t - kd = 96.96 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 5.92 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.02E+06 mm⁴
Effective Depth, d = 94 mm
 Mcr    Mcr 
3 3
 =
1.34E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.44E+08 mm⁴
1.44E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.83 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.31 kN/m Actual deflection
δact = δDL + δLL = 0.34 mm 8%
C. DIAGRAM Moment Inertia, Ix = 1.44E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.25 mm
δLL = 5Wll L⁴/384EcIx = 0.09 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@200mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@200mm

Left Right
Mu 3.72 3.72 kNm ø12@250mm
Ru = Mu/(øbd²) 0.47 0.47
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0017 0.0017
As = ρbd 188.0 188.0 mm²
S = 1000/As/Ab 602 602 mm
S = 3t → 360 360 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@200mm Top Bars at Left Supports
Say Spacing 200 250 mm Therefore Provide ø12@200mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.31 kNm
Service Total, Mt 1.78 kNm
Mu 2.33 kNm
Ru = Mu/(øbd²) 0.2927
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0011
As = ρbd 188.0 mm²
S = 1000/As/Ab 602 mm
S = 3t 360 mm ←
S= 450 450 mm
Say Spacing 200 mm
 DESIGN OF SLAB - S5

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0068
Thickness Used, t = 130 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.04
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.26
øBar = 12 mm kd = 26.86 mm
Es = 200000 Mpa Yt = t - kd = 103.14 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 7.08 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.61E+06 mm⁴
Effective Depth, d = 104 mm
 Mcr    Mcr 
3 3
 =
2.54E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.83E+08 mm⁴
1.83E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.06 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.59 kN/m Actual deflection
δact = δDL + δLL = 0.28 mm 7%
C. DIAGRAM Moment Inertia, Ix = 1.83E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.21 mm
δLL = 5Wll L⁴/384EcIx = 0.07 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@160mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@160mm

Left Right
Mu 3.84 3.84 kNm ø12@250mm
Ru = Mu/(øbd²) 0.39 0.39
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0014 0.0014
As = ρbd 208.0 208.0 mm²
S = 1000/As/Ab 544 544 mm
S = 3t → 390 390 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@160mm Top Bars at Left Supports
Say Spacing 160 250 mm Therefore Provide ø12@160mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.37 kNm
Service Total, Mt 1.84 kNm
Mu 2.40 kNm
Ru = Mu/(øbd²) 0.2464
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0009
As = ρbd 208.0 mm²
S = 1000/As/Ab 544 mm
S = 3t 390 mm ←
S= 450 450 mm
Say Spacing 160 mm
 DESIGN OF SLAB - S6

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0083
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.99
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.28
øBar = 12 mm kd = 31.98 mm
Es = 200000 Mpa Yt = t - kd = 108.02 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.44 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.73E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
4.74E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.23 mm 5%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.17 mm
δLL = 5Wll L⁴/384EcIx = 0.06 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@120mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 3.95 3.95 kNm ø12@250mm
Ru = Mu/(øbd²) 0.34 0.34
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0012 0.0012
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.42 kNm
Service Total, Mt 1.90 kNm
Mu 2.47 kNm
Ru = Mu/(øbd²) 0.2111
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0008
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - MS1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0068
Thickness Used, t = 130 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.04
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.26
øBar = 12 mm kd = 26.86 mm
Es = 200000 Mpa Yt = t - kd = 103.14 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 7.08 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.61E+06 mm⁴
Effective Depth, d = 104 mm
 Mcr    Mcr 
3 3
 =
2.54E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.83E+08 mm⁴
1.83E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.06 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.59 kN/m Actual deflection
δact = δDL + δLL = 0.28 mm 7%
C. DIAGRAM Moment Inertia, Ix = 1.83E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.21 mm
δLL = 5Wll L⁴/384EcIx = 0.07 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@160mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@160mm

Left Right
Mu 3.84 3.84 kNm ø12@250mm
Ru = Mu/(øbd²) 0.39 0.39
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0014 0.0014
As = ρbd 208.0 208.0 mm²
S = 1000/As/Ab 544 544 mm
S = 3t → 390 390 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@160mm Top Bars at Left Supports
Say Spacing 160 250 mm Therefore Provide ø12@160mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.37 kNm
Service Total, Mt 1.84 kNm
Mu 2.40 kNm
Ru = Mu/(øbd²) 0.2464
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0009
As = ρbd 208.0 mm²
S = 1000/As/Ab 544 mm
S = 3t 390 mm ←
S= 450 450 mm
Say Spacing 160 mm
 DESIGN OF SLAB - MS2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 2.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0100
Thickness Used, t = 120 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.93
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.30
øBar = 12 mm kd = 28.56 mm
Es = 200000 Mpa Yt = t - kd = 91.44 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 6.28 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.94E+06 mm⁴
Effective Depth, d = 94 mm
 Mcr    Mcr 
3 3
 =
1.59E+10 mm⁴
Aspect Ratio, m = 0.33
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.44E+08 mm⁴
1.44E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.83 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 4.17 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.31 kN/m Actual deflection
δact = δDL + δLL = 0.34 mm 8%
C. DIAGRAM Moment Inertia, Ix = 1.44E+08 mm⁴
Lleft Short Span Lright δDL = 5Wdl L⁴/384EcIx = 0.25 mm
δLL = 5Wll L⁴/384EcIx = 0.09 mm

WL²/10 WL²/10 F. DIAGRAM

L
WL²/16

Continuous Main Span Continuous ø12@120mm

D. DESIGN
End type = Both Ends Continuous
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 3.72 3.72 kNm ø12@250mm
Ru = Mu/(øbd²) 0.47 0.47
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0017 0.0017
As = ρbd 188.0 188.0 mm²
S = 1000/As/Ab 602 602 mm
S = 3t → 360 360 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 1.31 kNm
Service Total, Mt 1.78 kNm
Mu 2.33 kNm
Ru = Mu/(øbd²) 0.2927
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0011
As = ρbd 188.0 mm²
S = 1000/As/Ab 602 mm
S = 3t 360 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - GCS-1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 1.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0083
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.99
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.28
øBar = 12 mm kd = 31.98 mm
Es = 200000 Mpa Yt = t - kd = 108.02 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.44 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.73E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
5.93E+09 mm⁴
Aspect Ratio, m = 0.16
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 2.08 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.14 mm 7%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = Wdl L⁴/8EcIx = 0.10 mm
δLL = Wll L⁴/8EcIx = 0.03 mm

WL²/2 WL²/2 F. DIAGRAM

Supported Main Span Unsupported ø12@120mm

D. DESIGN
End type = Cantilever
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 4.94 4.94 kNm ø12@250mm
Ru = Mu/(øbd²) 0.42 0.42
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0015 0.0015
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 2.85 kNm
Service Total, Mt 3.80 kNm
Mu 0.00 kNm
Ru = Mu/(øbd²) 0.0000
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0000
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - DCS2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 1.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0100
Thickness Used, t = 120 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.93
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.30
øBar = 12 mm kd = 28.56 mm
Es = 200000 Mpa Yt = t - kd = 91.44 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 6.28 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 1.94E+06 mm⁴
Effective Depth, d = 94 mm
 Mcr    Mcr 
3 3
 =
1.99E+09 mm⁴
Aspect Ratio, m = 0.16
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.44E+08 mm⁴
1.44E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.83 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 2.08 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.31 kN/m Actual deflection
δact = δDL + δLL = 0.20 mm 10%
C. DIAGRAM Moment Inertia, Ix = 1.44E+08 mm⁴
Lleft Short Span Lright δDL = Wdl L⁴/8EcIx = 0.15 mm
δLL = Wll L⁴/8EcIx = 0.05 mm

WL²/2 WL²/2 F. DIAGRAM

Supported Main Span Unsupported ø12@120mm

D. DESIGN
End type = Cantilever
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 4.66 4.66 kNm ø12@250mm
Ru = Mu/(øbd²) 0.59 0.59
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0021 0.0021
As = ρbd 201.1 201.1 mm²
S = 1000/As/Ab 562 562 mm
S = 3t → 360 360 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 2.61 kNm
Service Total, Mt 3.56 kNm
Mu 0.00 kNm
Ru = Mu/(øbd²) 0.0000
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0000
As = ρbd 188.0 mm²
S = 1000/As/Ab 602 mm
S = 3t 360 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - CS1

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 1.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0083
Thickness Used, t = 140 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 0.99
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.28
øBar = 12 mm kd = 31.98 mm
Es = 200000 Mpa Yt = t - kd = 108.02 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 8.44 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 2.73E+06 mm⁴
Effective Depth, d = 114 mm
 Mcr    Mcr 
3 3
 =
5.93E+09 mm⁴
Aspect Ratio, m = 0.16
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
2.29E+08 mm⁴
2.29E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 3.30 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 2.08 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.88 kN/m Actual deflection
δact = δDL + δLL = 0.14 mm 7%
C. DIAGRAM Moment Inertia, Ix = 2.29E+08 mm⁴
Lleft Short Span Lright δDL = Wdl L⁴/8EcIx = 0.10 mm
δLL = Wll L⁴/8EcIx = 0.03 mm

WL²/2 WL²/2 F. DIAGRAM

Supported Main Span Unsupported ø12@120mm

D. DESIGN
End type = Cantilever
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@120mm

Left Right
Mu 4.94 4.94 kNm ø12@250mm
Ru = Mu/(øbd²) 0.42 0.42
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0015 0.0015
As = ρbd 228.0 228.0 mm²
S = 1000/As/Ab 496 496 mm
S = 3t → 420 420 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@120mm Top Bars at Left Supports
Say Spacing 120 250 mm Therefore Provide ø12@120mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 2.85 kNm
Service Total, Mt 3.80 kNm
Mu 0.00 kNm
Ru = Mu/(øbd²) 0.0000
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0000
As = ρbd 228.0 mm²
S = 1000/As/Ab 496 mm
S = 3t 420 mm ←
S= 450 450 mm
Say Spacing 120 mm
 DESIGN OF SLAB - CS2

A. DESIGN INPUTS E. MOMENT OF INERTIA

Short Span, S = 1.00 m Time Dependent, ξ = 1.40
Long Span, L = 6.10 m Ratio Provided, ρ' = Aø/sd = 0.0040
Thickness Used, t = 120 mm Long Time δ Factor, λ = ξ/(1+50ρ') = 1.17
Unit Weight of Concrete, = 23.55 kN/m³ Rupture Modulus, fr = 0.62λc√f'c = 3.99 Mpa
Compressive Strength, f'c = 41.38 Mpa n = Es/Ec = 6.62
Concrete, λc = 1.00 Mpa k = √[(ρ'n)²+2ρ'n]-ρ'n = 0.21
øBar = 12 mm kd = 19.30 mm
Es = 200000 Mpa Yt = t - kd = 100.70 mm
Ec = 4700√f'c = 30234 Mpa Cracked Moment, Mcr = fr Ig/Yt = 5.70 kNm
Yield Strength, fy = 276 Mpa Cracked Inertia, Icr = b (kd)³/12 = 5.99E+05 mm⁴
Effective Depth, d = 94 mm
 Mcr    Mcr 
3 3
 =
1.50E+09 mm⁴
Aspect Ratio, m = 0.16
Ieff=  Ig  Ig+ 1-    Icr
ONE-WAY SLAB
Therefore analyze as One Way Slab!!
 Mdl 
Gross Inertia,
  Mt   ==
1.44E+08 mm⁴
1.44E+08 mm⁴
Ix,used

B. LOAD CONSIDERED D. DEFLECTION

Self Weight, SW = 2.83 kPa Allowable deflection
Super Dead Load, SDL = 2.40 kPa δall = L/480 = 2.08 mm
Floor Live Load, LL = 1.90 kPa
Wu = 1.2DL + 1.6LL = 9.31 kN/m Actual deflection
δact = δDL + δLL = 0.20 mm 10%
C. DIAGRAM Moment Inertia, Ix = 1.44E+08 mm⁴
Lleft Short Span Lright δDL = Wdl L⁴/8EcIx = 0.15 mm
δLL = Wll L⁴/8EcIx = 0.05 mm

WL²/2 WL²/2 F. DIAGRAM

Supported Main Span Unsupported ø12@300mm

D. DESIGN
End type = Cantilever
Minimum Steel Ratio, ρmin = 0.0020
S

I. Reinforcements @ Supports ø12@300mm

Left Right
Mu 4.66 4.66 kNm ø12@250mm
Ru = Mu/(øbd²) 0.59 0.59
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0021 0.0021
As = ρbd 201.1 201.1 mm²
S = 1000/As/Ab 562 562 mm
S = 3t → 360 360 mm ← SUMMARY
S= 450 450 450 mm Therefore Provide ø12@300mm Top Bars at Left Supports
Say Spacing 300 250 mm Therefore Provide ø12@300mm Bottom Bars at Mid Span
Therefore Provide ø12@250mm Top Bars at Right Supports
II. Reinforcements @ Mid Span
Service DL, Mdl 2.61 kNm
Service Total, Mt 3.56 kNm
Mu 0.00 kNm
Ru = Mu/(øbd²) 0.0000
ρ = .85f'c/fy(1-√1-2Ru/0.85f'c) 0.0000
As = ρbd 188.0 mm²
S = 1000/As/Ab 602 mm
S = 3t 360 mm ←
S= 450 450 mm
Say Spacing 300 mm
 DESIGN OF FOOTING (F-3)

A. DESIGN INPUTS ONE-WAY SHEAR (WIDE BEAM SHEAR)

Unit Weight of Concrete, Ɣc = 24.00 kN/m³ Effective Depth = 488 mm
Compressive Strength, f'c = 41.38 Mpa
Yield Strength, Fy = 414 Mpa At X - Direction At Y - Direction
Rebar Diameter, Ø = 25 mm Vu, kN ΦVc, kN D/C Vu, kN ΦVc, kN D/C
β1 = 0.85 - 0.05(f'c-28)/7 = 0.75 1 -64.50 719.70 -0.09 SAFE! 1 29.77 479.80 0.06 SAFE!
2 -64.50 719.70 -0.09 SAFE! 2 29.77 479.80 0.06 SAFE!
Allowable Soil Bearing Capacity, qa = 500 Kpa 3 -64.50 719.70 -0.09 SAFE! 3 29.77 479.80 0.06 SAFE!
Soil Density = 18.00 kN/m³
Embedment, D = 2.00 m TWO-WAY SHEAR (PUNCHING)
Effective Depth = 500 mm
B. FOOTING DIMENSION bo = 4300 mm
X-Direction, L = 1.20 m ΦVc = 3457.56 kN
Y-Direction, B = 1.80 m
Thickness, t = 600 mm P, kN Vu, kN D/C
0.6 1 606.92 171.06 0.05 SAFE!
C. COLUMN DIMENSION 2 606.92 184.92 0.05 SAFE!
Column Type: INTERIOR αs = 40 3 606.92 184.92 0.05 SAFE!
X-Direction = 0.55 m
Y-Direction = 0.60 m F. REINFORCEMENT
β (ratio of larger column/smaller column) = 1 ρmin = 1.4/fy OR sqrt(f'c)/4fy = 0.00389
0.85 f ' c  1(600)
 max = 0.75 = 0.02748
D. DESIGN FORCES fy(600 + fy)

SERVICE LOAD
Fz, kN Mx, kN-m My, kN-m ALONG X-DIRECTION
1 Max Axial 202.000 0.000 0.000 Max Mu = 13.97 kN-m
2 Max Mx 202.000 0.000 0.000 Rn = 0.0544 Mpa
3 Max My 202.000 0.000 0.000 ρactual = 0.000132
Therefore, use ρ = 0.000176
ULTIMATE LOAD ρactual < ρmax, SAFE!
Fz, kN Mx, kN-m My, kN-m Smax = 250 mm
1 Max Axial 440.000 0.000 0.000 Spacing = 250 mm
2 Max Mx 440.000 0.000 0.000 No. of Bars @ X-Direction = 6 pcs
3 Max My 440.000 0.000 0.000
ALONG Y-DIRECTION
E. DESIGN Max Mu = 47.63 kN-m
Effective Soil Bearing Capacity, qe = 460 kPa Rn = 0.1237 Mpa
ρactual = 0.000299
FOOTING AREA Therefore, use ρ = 0.000399
qu max, kPa D/C qu min, kPa D/C ρactual < ρmax, SAFE!
1 143.92 SAFE! 0.29 143.92 SAFE! 0.29 Smax = 250 mm
2 131.32 SAFE! 0.26 131.32 SAFE! 0.26 Spacing = 200 mm
3 131.32 SAFE! 0.26 131.32 SAFE! 0.26 No. of Bars @ Y-Direction = 10 pcs

G. DIAGRAM

SUMMARY
Therefore, use 1.2m x 1.8m x 600mm depth footing.
Therefore, provide 10 - ø25mm // to B
Therefore, provide 6 - ø25mm // to L

At X - Direction
x1 x2 x3 x4 f1, kPa f2, kPa f3, kPa f4, kPa
1 0.763 -0.163 0.275 0.325 280.98 280.98 280.98 60.48
2 0.763 -0.163 0.275 0.325 280.98 280.98 280.98 60.48
3 0.763 -0.163 0.275 0.325 280.98 280.98 280.98 60.48
At Y - Direction
y1 y2 y3 y4 f1, kPa f2, kPa f3, kPa f4, kPa
1 0.788 0.113 0.300 0.600 280.98 280.98 280.98 60.48
2 0.788 0.113 0.300 0.600 280.98 280.98 280.98 60.48
3 0.788 0.113 0.300 0.600 280.98 280.98 280.98 60.48
1 Loads
This chapter provides loading information as applied to the model.

1.1 Load Patterns

Table 1.1 - Load Patterns

Self
Name Type Weight Auto Load
Multiplier
Dead Dead 1
Live Live 0
Superimposed
SDL 0
Dead
WX Wind 0 ASCE 7-10
WY Wind 0 ASCE 7-10
EQXPE Seismic 0 UBC 97
EQYPE Seismic 0 UBC 97
EQXNE Seismic 0 UBC 97
EQYNE Seismic 0 UBC 97
WZ Wind 0 ASCE 7-10

1.2 Load Sets

Table 1.2 - Shell Uniform Load Sets
Load Load
Load Set
Pattern kN/m²
RESIDENTIAL SDL 3
RESIDENTIAL Live 2
ROOF - SOLAR PANEL SDL 2
ROOF - SOLAR PANEL Live 1.5
ROOF ONLY SDL 1.5
ROOF ONLY Live 1
BALCONY / CORRIDOR /
SDL 3
STAIRS
BALCONY / CORRIDOR /
Live 4.8
STAIRS
PARKING SDL 3
PARKING Live 4.8

Page 1 of 32
ASCE 7-10 Auto Wind Load Calculation
This calculation presents the automatically generated lateral wind loads for load pattern WX according to ASCE
7-10, as calculated by ETABS.
Exposure Parameters

Exposure From = Diaphragms

Exposure Category = B

Wind Direction = 0 degrees

Basic Wind Speed, V [ASCE 26.5.1] V = 162 mph

Windward Coefficient, Cp,wind [ASCE 27.4.1] C , = Varies
Leeward Coefficient, Cp,lee [ASCE 27.4.1] C , = Varies

Wind Case = All Cases

Top Story = RD2

Bottom Story = Base

Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1] z = 1200

Emperical Exponent, α [ASCE Table 26.9-1] α=7
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-
1] K = 2.01( for 15ft ≤ z ≤ z

K = 2.01( for z 15ft

Topographical Factor, Kzt [ASCE 26.8.2] K =1
Directionality Factor, Kd [ASCE 26.6] K = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1] q = 0.00256K K K V

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2] p = qGC , + q (GC , )

Applied Story Forces

Page 2 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 178.05 0 RD2 70 0 192.915
RD1 66.5 353.9496 0 RD1 66.5 0 383.5002
RD 63 350.6285 0 RD 63 0 379.9017
15TH 59.5 376.8015 0 15TH 59.5 0 376.1574
14TH 56 372.8896 0 14TH 56 0 372.2521
13TH 52.5 368.7986 0 13TH 52.5 0 368.1682
12TH 49 364.5077 0 12TH 49 0 363.8846
11TH 45.5 359.9916 0 11TH 45.5 0 359.3762
10TH 42 355.2195 0 10TH 42 0 354.6123
9TH 38.5 350.1538 0 9TH 38.5 0 349.5552
8TH 35 344.7466 0 8TH 35 0 344.1573
7TH 31.5 338.937 0 7TH 31.5 0 338.3576
6TH 28 332.6442 0 6TH 28 0 332.0756
5TH 24.5 325.7588 0 5TH 24.5 0 325.202
4TH 21 318.1253 0 4TH 21 0 317.5815
3RD 17.5 309.5117 0 3RD 17.5 0 308.9826
2ND 14 299.5446 0 2ND 14 0 299.0326
MEZZANIN MEZZANIN
10.5 287.5547 0 10.5 0 287.0631
E E
GROUND 7 314.5646 0 GROUND 7 0 333.1779
2ND 2ND
3.5 300.1152 0 3.5 0 317.8735
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 3 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 133.5375 0 RD2 70 133.5375 0
RD1 66.5 265.4622 0 RD1 66.5 265.4622 0
RD 63 262.9714 0 RD 63 262.9714 0
15TH 59.5 282.6012 0 15TH 59.5 282.6012 0
14TH 56 279.6672 0 14TH 56 279.6672 0
13TH 52.5 276.599 0 13TH 52.5 276.599 0
12TH 49 273.3808 0 12TH 49 273.3808 0
11TH 45.5 269.9937 0 11TH 45.5 269.9937 0
10TH 42 266.4147 0 10TH 42 266.4147 0
9TH 38.5 262.6153 0 9TH 38.5 262.6153 0
8TH 35 258.56 0 8TH 35 258.56 0
7TH 31.5 254.2027 0 7TH 31.5 254.2027 0
6TH 28 249.4832 0 6TH 28 249.4832 0
5TH 24.5 244.3191 0 5TH 24.5 244.3191 0
4TH 21 238.594 0 4TH 21 238.594 0
3RD 17.5 232.1338 0 3RD 17.5 232.1338 0
2ND 14 224.6585 0 2ND 14 224.6585 0
MEZZANIN MEZZANIN
10.5 215.666 0 10.5 215.666 0
E E
GROUND 7 235.9235 0 GROUND 7 235.9235 0
2ND 2ND
3.5 225.0864 0 3.5 225.0864 0
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 4 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 0 144.6863 RD2 70 0 144.6863
RD1 66.5 0 287.6251 RD1 66.5 0 287.6251
RD 63 0 284.9263 RD 63 0 284.9263
15TH 59.5 0 282.1181 15TH 59.5 0 282.1181
14TH 56 0 279.1891 14TH 56 0 279.1891
13TH 52.5 0 276.1261 13TH 52.5 0 276.1261
12TH 49 0 272.9135 12TH 49 0 272.9135
11TH 45.5 0 269.5321 11TH 45.5 0 269.5321
10TH 42 0 265.9592 10TH 42 0 265.9592
9TH 38.5 0 262.1664 9TH 38.5 0 262.1664
8TH 35 0 258.118 8TH 35 0 258.118
7TH 31.5 0 253.7682 7TH 31.5 0 253.7682
6TH 28 0 249.0567 6TH 28 0 249.0567
5TH 24.5 0 243.9015 5TH 24.5 0 243.9015
4TH 21 0 238.1861 4TH 21 0 238.1861
3RD 17.5 0 231.737 3RD 17.5 0 231.737
2ND 14 0 224.2744 2ND 14 0 224.2744
MEZZANIN MEZZANIN
10.5 0 215.2974 10.5 0 215.2974
E E
GROUND 7 0 249.8834 GROUND 7 0 249.8834
2ND 2ND
3.5 0 238.4051 3.5 0 238.4051
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 5 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 133.5375 -144.6863 RD2 70 133.5375 144.6863
RD1 66.5 265.4622 -287.6251 RD1 66.5 265.4622 287.6251
RD 63 262.9714 -284.9263 RD 63 262.9714 284.9263
15TH 59.5 282.6012 -282.1181 15TH 59.5 282.6012 282.1181
14TH 56 279.6672 -279.1891 14TH 56 279.6672 279.1891
13TH 52.5 276.599 -276.1261 13TH 52.5 276.599 276.1261
12TH 49 273.3808 -272.9135 12TH 49 273.3808 272.9135
11TH 45.5 269.9937 -269.5321 11TH 45.5 269.9937 269.5321
10TH 42 266.4147 -265.9592 10TH 42 266.4147 265.9592
9TH 38.5 262.6153 -262.1664 9TH 38.5 262.6153 262.1664
8TH 35 258.56 -258.118 8TH 35 258.56 258.118
7TH 31.5 254.2027 -253.7682 7TH 31.5 254.2027 253.7682
6TH 28 249.4832 -249.0567 6TH 28 249.4832 249.0567
5TH 24.5 244.3191 -243.9015 5TH 24.5 244.3191 243.9015
4TH 21 238.594 -238.1861 4TH 21 238.594 238.1861
3RD 17.5 232.1338 -231.737 3RD 17.5 232.1338 231.737
2ND 14 224.6585 -224.2744 2ND 14 224.6585 224.2744
MEZZANIN MEZZANIN
10.5 215.666 -215.2974 10.5 215.666 215.2974
E E
GROUND 7 235.9235 -249.8834 GROUND 7 235.9235 249.8834
2ND 2ND
3.5 225.0864 -238.4051 3.5 225.0864 238.4051
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 6 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 100.2421 -108.6112 RD2 70 100.2421 -108.6112
RD1 66.5 199.2736 -215.9106 RD1 66.5 199.2736 -215.9106
RD 63 197.4038 -213.8847 RD 63 197.4038 -213.8847
15TH 59.5 212.1393 -211.7766 15TH 59.5 212.1393 -211.7766
14TH 56 209.9368 -209.578 14TH 56 209.9368 -209.578
13TH 52.5 207.6336 -207.2787 13TH 52.5 207.6336 -207.2787
12TH 49 205.2178 -204.867 12TH 49 205.2178 -204.867
11TH 45.5 202.6752 -202.3288 11TH 45.5 202.6752 -202.3288
10TH 42 199.9886 -199.6467 10TH 42 199.9886 -199.6467
9TH 38.5 197.1366 -196.7996 9TH 38.5 197.1366 -196.7996
8TH 35 194.0923 -193.7606 8TH 35 194.0923 -193.7606
7TH 31.5 190.8215 -190.4953 7TH 31.5 190.8215 -190.4953
6TH 28 187.2787 -186.9586 6TH 28 187.2787 -186.9586
5TH 24.5 183.4022 -183.0887 5TH 24.5 183.4022 -183.0887
4TH 21 179.1046 -178.7984 4TH 21 179.1046 -178.7984
3RD 17.5 174.2551 -173.9572 3RD 17.5 174.2551 -173.9572
2ND 14 168.6436 -168.3553 2ND 14 168.6436 -168.3553
MEZZANIN MEZZANIN
10.5 161.8933 -161.6166 10.5 161.8933 -161.6166
E E
GROUND 7 177.0999 -187.5792 GROUND 7 177.0999 -187.5792
2ND 2ND
3.5 168.9649 -178.9628 3.5 168.9649 -178.9628
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 7 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 100.2421 108.6112 RD2 70 100.2421 108.6112
RD1 66.5 199.2736 215.9106 RD1 66.5 199.2736 215.9106
RD 63 197.4038 213.8847 RD 63 197.4038 213.8847
15TH 59.5 212.1393 211.7766 15TH 59.5 212.1393 211.7766
14TH 56 209.9368 209.578 14TH 56 209.9368 209.578
13TH 52.5 207.6336 207.2787 13TH 52.5 207.6336 207.2787
12TH 49 205.2178 204.867 12TH 49 205.2178 204.867
11TH 45.5 202.6752 202.3288 11TH 45.5 202.6752 202.3288
10TH 42 199.9886 199.6467 10TH 42 199.9886 199.6467
9TH 38.5 197.1366 196.7996 9TH 38.5 197.1366 196.7996
8TH 35 194.0923 193.7606 8TH 35 194.0923 193.7606
7TH 31.5 190.8215 190.4953 7TH 31.5 190.8215 190.4953
6TH 28 187.2787 186.9586 6TH 28 187.2787 186.9586
5TH 24.5 183.4022 183.0887 5TH 24.5 183.4022 183.0887
4TH 21 179.1046 178.7984 4TH 21 179.1046 178.7984
3RD 17.5 174.2551 173.9572 3RD 17.5 174.2551 173.9572
2ND 14 168.6436 168.3553 2ND 14 168.6436 168.3553
MEZZANIN MEZZANIN
10.5 161.8933 161.6166 10.5 161.8933 161.6166
E E
GROUND 7 177.0999 187.5792 GROUND 7 177.0999 187.5792
2ND 2ND
3.5 168.9649 178.9628 3.5 168.9649 178.9628
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 8 of 32
ASCE 7-10 Auto Wind Load Calculation
This calculation presents the automatically generated lateral wind loads for load pattern WY according to ASCE
7-10, as calculated by ETABS.
Exposure Parameters

Exposure From = Diaphragms

Exposure Category = B

Wind Direction = 90 degrees

Basic Wind Speed, V [ASCE 26.5.1] V = 162 mph

Windward Coefficient, Cp,wind [ASCE 27.4.1] C , = Varies
Leeward Coefficient, Cp,lee [ASCE 27.4.1] C , = Varies

Wind Case = All Cases

Top Story = RD2

Bottom Story = Base

Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1] z = 1200

Emperical Exponent, α [ASCE Table 26.9-1] α=7
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-
1] K = 2.01( for 15ft ≤ z ≤ z

K = 2.01( for z 15ft

Topographical Factor, Kzt [ASCE 26.8.2] K =1
Directionality Factor, Kd [ASCE 26.6] K = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1] q = 0.00256K K K V

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2] p = qGC , + q (GC , )

Applied Story Forces

Page 9 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 0 192.915 RD2 70 -178.05 0
RD1 66.5 0 383.5002 RD1 66.5 -353.9496 0
RD 63 0 379.9017 RD 63 -350.6285 0
15TH 59.5 0 376.1574 15TH 59.5 -376.8015 0
14TH 56 0 372.2521 14TH 56 -372.8896 0
13TH 52.5 0 368.1682 13TH 52.5 -368.7986 0
12TH 49 0 363.8846 12TH 49 -364.5077 0
11TH 45.5 0 359.3762 11TH 45.5 -359.9916 0
10TH 42 0 354.6123 10TH 42 -355.2195 0
9TH 38.5 0 349.5552 9TH 38.5 -350.1538 0
8TH 35 0 344.1573 8TH 35 -344.7466 0
7TH 31.5 0 338.3576 7TH 31.5 -338.937 0
6TH 28 0 332.0756 6TH 28 -332.6442 0
5TH 24.5 0 325.202 5TH 24.5 -325.7588 0
4TH 21 0 317.5815 4TH 21 -318.1253 0
3RD 17.5 0 308.9826 3RD 17.5 -309.5117 0
2ND 14 0 299.0326 2ND 14 -299.5446 0
MEZZANIN MEZZANIN
10.5 0 287.0631 10.5 -287.5547 0
E E
GROUND 7 0 333.1779 GROUND 7 -314.5646 0
2ND 2ND
3.5 0 317.8735 3.5 -300.1152 0
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 10 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 0 144.6863 RD2 70 0 144.6863
RD1 66.5 0 287.6251 RD1 66.5 0 287.6251
RD 63 0 284.9263 RD 63 0 284.9263
15TH 59.5 0 282.1181 15TH 59.5 0 282.1181
14TH 56 0 279.1891 14TH 56 0 279.1891
13TH 52.5 0 276.1261 13TH 52.5 0 276.1261
12TH 49 0 272.9135 12TH 49 0 272.9135
11TH 45.5 0 269.5321 11TH 45.5 0 269.5321
10TH 42 0 265.9592 10TH 42 0 265.9592
9TH 38.5 0 262.1664 9TH 38.5 0 262.1664
8TH 35 0 258.118 8TH 35 0 258.118
7TH 31.5 0 253.7682 7TH 31.5 0 253.7682
6TH 28 0 249.0567 6TH 28 0 249.0567
5TH 24.5 0 243.9015 5TH 24.5 0 243.9015
4TH 21 0 238.1861 4TH 21 0 238.1861
3RD 17.5 0 231.737 3RD 17.5 0 231.737
2ND 14 0 224.2744 2ND 14 0 224.2744
MEZZANIN MEZZANIN
10.5 0 215.2974 10.5 0 215.2974
E E
GROUND 7 0 249.8834 GROUND 7 0 249.8834
2ND 2ND
3.5 0 238.4051 3.5 0 238.4051
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 11 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 -133.5375 0 RD2 70 -133.5375 0
RD1 66.5 -265.4622 0 RD1 66.5 -265.4622 0
RD 63 -262.9714 0 RD 63 -262.9714 0
15TH 59.5 -282.6012 0 15TH 59.5 -282.6012 0
14TH 56 -279.6672 0 14TH 56 -279.6672 0
13TH 52.5 -276.599 0 13TH 52.5 -276.599 0
12TH 49 -273.3808 0 12TH 49 -273.3808 0
11TH 45.5 -269.9937 0 11TH 45.5 -269.9937 0
10TH 42 -266.4147 0 10TH 42 -266.4147 0
9TH 38.5 -262.6153 0 9TH 38.5 -262.6153 0
8TH 35 -258.56 0 8TH 35 -258.56 0
7TH 31.5 -254.2027 0 7TH 31.5 -254.2027 0
6TH 28 -249.4832 0 6TH 28 -249.4832 0
5TH 24.5 -244.3191 0 5TH 24.5 -244.3191 0
4TH 21 -238.594 0 4TH 21 -238.594 0
3RD 17.5 -232.1338 0 3RD 17.5 -232.1338 0
2ND 14 -224.6585 0 2ND 14 -224.6585 0
MEZZANIN MEZZANIN
10.5 -215.666 0 10.5 -215.666 0
E E
GROUND 7 -235.9235 0 GROUND 7 -235.9235 0
2ND 2ND
3.5 -225.0864 0 3.5 -225.0864 0
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 12 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 133.5375 144.6863 RD2 70 -133.5375 144.6863
RD1 66.5 265.4622 287.6251 RD1 66.5 -265.4622 287.6251
RD 63 262.9714 284.9263 RD 63 -262.9714 284.9263
15TH 59.5 282.6012 282.1181 15TH 59.5 -282.6012 282.1181
14TH 56 279.6672 279.1891 14TH 56 -279.6672 279.1891
13TH 52.5 276.599 276.1261 13TH 52.5 -276.599 276.1261
12TH 49 273.3808 272.9135 12TH 49 -273.3808 272.9135
11TH 45.5 269.9937 269.5321 11TH 45.5 -269.9937 269.5321
10TH 42 266.4147 265.9592 10TH 42 -266.4147 265.9592
9TH 38.5 262.6153 262.1664 9TH 38.5 -262.6153 262.1664
8TH 35 258.56 258.118 8TH 35 -258.56 258.118
7TH 31.5 254.2027 253.7682 7TH 31.5 -254.2027 253.7682
6TH 28 249.4832 249.0567 6TH 28 -249.4832 249.0567
5TH 24.5 244.3191 243.9015 5TH 24.5 -244.3191 243.9015
4TH 21 238.594 238.1861 4TH 21 -238.594 238.1861
3RD 17.5 232.1338 231.737 3RD 17.5 -232.1338 231.737
2ND 14 224.6585 224.2744 2ND 14 -224.6585 224.2744
MEZZANIN MEZZANIN
10.5 215.666 215.2974 10.5 -215.666 215.2974
E E
GROUND 7 235.9235 249.8834 GROUND 7 -235.9235 249.8834
2ND 2ND
3.5 225.0864 238.4051 3.5 -225.0864 238.4051
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 13 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 100.2421 108.6112 RD2 70 100.2421 108.6112
RD1 66.5 199.2736 215.9106 RD1 66.5 199.2736 215.9106
RD 63 197.4038 213.8847 RD 63 197.4038 213.8847
15TH 59.5 212.1393 211.7766 15TH 59.5 212.1393 211.7766
14TH 56 209.9368 209.578 14TH 56 209.9368 209.578
13TH 52.5 207.6336 207.2787 13TH 52.5 207.6336 207.2787
12TH 49 205.2178 204.867 12TH 49 205.2178 204.867
11TH 45.5 202.6752 202.3288 11TH 45.5 202.6752 202.3288
10TH 42 199.9886 199.6467 10TH 42 199.9886 199.6467
9TH 38.5 197.1366 196.7996 9TH 38.5 197.1366 196.7996
8TH 35 194.0923 193.7606 8TH 35 194.0923 193.7606
7TH 31.5 190.8215 190.4953 7TH 31.5 190.8215 190.4953
6TH 28 187.2787 186.9586 6TH 28 187.2787 186.9586
5TH 24.5 183.4022 183.0887 5TH 24.5 183.4022 183.0887
4TH 21 179.1046 178.7984 4TH 21 179.1046 178.7984
3RD 17.5 174.2551 173.9572 3RD 17.5 174.2551 173.9572
2ND 14 168.6436 168.3553 2ND 14 168.6436 168.3553
MEZZANIN MEZZANIN
10.5 161.8933 161.6166 10.5 161.8933 161.6166
E E
GROUND 7 177.0999 187.5792 GROUND 7 177.0999 187.5792
2ND 2ND
3.5 168.9649 178.9628 3.5 168.9649 178.9628
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 14 of 32
 Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir
m kN kN m kN kN
RD2 70 -100.2421 108.6112 RD2 70 -100.2421 108.6112
RD1 66.5 -199.2736 215.9106 RD1 66.5 -199.2736 215.9106
RD 63 -197.4038 213.8847 RD 63 -197.4038 213.8847
15TH 59.5 -212.1393 211.7766 15TH 59.5 -212.1393 211.7766
14TH 56 -209.9368 209.578 14TH 56 -209.9368 209.578
13TH 52.5 -207.6336 207.2787 13TH 52.5 -207.6336 207.2787
12TH 49 -205.2178 204.867 12TH 49 -205.2178 204.867
11TH 45.5 -202.6752 202.3288 11TH 45.5 -202.6752 202.3288
10TH 42 -199.9886 199.6467 10TH 42 -199.9886 199.6467
9TH 38.5 -197.1366 196.7996 9TH 38.5 -197.1366 196.7996
8TH 35 -194.0923 193.7606 8TH 35 -194.0923 193.7606
7TH 31.5 -190.8215 190.4953 7TH 31.5 -190.8215 190.4953
6TH 28 -187.2787 186.9586 6TH 28 -187.2787 186.9586
5TH 24.5 -183.4022 183.0887 5TH 24.5 -183.4022 183.0887
4TH 21 -179.1046 178.7984 4TH 21 -179.1046 178.7984
3RD 17.5 -174.2551 173.9572 3RD 17.5 -174.2551 173.9572
2ND 14 -168.6436 168.3553 2ND 14 -168.6436 168.3553
MEZZANIN MEZZANIN
10.5 -161.8933 161.6166 10.5 -161.8933 161.6166
E E
GROUND 7 -177.0999 187.5792 GROUND 7 -177.0999 187.5792
2ND 2ND
3.5 -168.9649 178.9628 3.5 -168.9649 178.9628
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 15 of 32
 30 Nov 2018

ASCE 7-10 Auto Wind Load Calculation

This calculation presents the automatically generated lateral wind loads for load pattern WZ according to ASCE
7-10, as calculated by ETABS.

Exposure Parameters

Exposure From = Diaphragms

Exposure Category = B

Wind Direction = 0 degrees

Basic Wind Speed, V [ASCE 26.5.1] V = 85 mph

Windward Coefficient, Cp,wind [ASCE 27.4.1] C , = Varies
Leeward Coefficient, Cp,lee [ASCE 27.4.1] C , = Varies

Wind Case = All Cases

Top Story = RD2

Bottom Story = Base

Include Parapet = No

Factors and Coefficients

Gradient Height, zg [ASCE Table 26.9-1] z = 1200

Emperical Exponent, α [ASCE Table 26.9-1] α=7
Velocity Pressure Exposure Coefficient, Kz; [ASCE Table 27.3-
1] K = 2.01( for 15ft ≤ z ≤ z

K = 2.01( for z 15ft

Topographical Factor, Kzt [ASCE 26.8.2] K =1
Directionality Factor, Kd [ASCE 26.6] K = 0.85
Gust Effect Factor, G [ASCE 26.9] G = 0.85

Lateral Loading

Velocity Pressure, qz [ASCE 27.3.2 Eq. 27.3-1] q = 0.00256K K K V

Design Wind Pressure, p [ASCE 27.4.2 Eq. 27.4-2] p = qGC , + q (GC , )

Applied Story Forces

Page 16 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 49.0173 0 RD2 70 0 53.1097
RD1 66.5 97.4427 0 RD1 66.5 0 105.578
RD 63 96.5284 0 RD 63 0 104.5873
15TH 59.5 103.7338 0 15TH 59.5 0 103.5565
14TH 56 102.6569 0 14TH 56 0 102.4814
13TH 52.5 101.5306 0 13TH 52.5 0 101.3571
12TH 49 100.3493 0 12TH 49 0 100.1778
11TH 45.5 99.106 0 11TH 45.5 0 98.9366
10TH 42 97.7923 0 10TH 42 0 97.6251
9TH 38.5 96.3977 0 9TH 38.5 0 96.2329
8TH 35 94.9091 0 8TH 35 0 94.7469
7TH 31.5 93.3097 0 7TH 31.5 0 93.1502
6TH 28 91.5773 0 6TH 28 0 91.4208
5TH 24.5 89.6817 0 5TH 24.5 0 89.5284
4TH 21 87.5802 0 4TH 21 0 87.4305
3RD 17.5 85.2089 0 3RD 17.5 0 85.0632
2ND 14 82.4649 0 2ND 14 0 82.324
MEZZANIN MEZZANIN
10.5 79.1641 0 10.5 0 79.0288
E E
GROUND 7 86.6 0 GROUND 7 0 91.7242
2ND 2ND
3.5 82.622 0 3.5 0 87.5109
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 17 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 36.763 0 RD2 70 36.763 0
RD1 66.5 73.082 0 RD1 66.5 73.082 0
RD 63 72.3963 0 RD 63 72.3963 0
15TH 59.5 77.8004 0 15TH 59.5 77.8004 0
14TH 56 76.9927 0 14TH 56 76.9927 0
13TH 52.5 76.148 0 13TH 52.5 76.148 0
12TH 49 75.262 0 12TH 49 75.262 0
11TH 45.5 74.3295 0 11TH 45.5 74.3295 0
10TH 42 73.3442 0 10TH 42 73.3442 0
9TH 38.5 72.2983 0 9TH 38.5 72.2983 0
8TH 35 71.1818 0 8TH 35 71.1818 0
7TH 31.5 69.9823 0 7TH 31.5 69.9823 0
6TH 28 68.683 0 6TH 28 68.683 0
5TH 24.5 67.2613 0 5TH 24.5 67.2613 0
4TH 21 65.6852 0 4TH 21 65.6852 0
3RD 17.5 63.9067 0 3RD 17.5 63.9067 0
2ND 14 61.8487 0 2ND 14 61.8487 0
MEZZANIN MEZZANIN
10.5 59.3731 0 10.5 59.3731 0
E E
GROUND 7 64.95 0 GROUND 7 64.95 0
2ND 2ND
3.5 61.9665 0 3.5 61.9665 0
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 18 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 0 39.8323 RD2 70 0 39.8323
RD1 66.5 0 79.1835 RD1 66.5 0 79.1835
RD 63 0 78.4405 RD 63 0 78.4405
15TH 59.5 0 77.6674 15TH 59.5 0 77.6674
14TH 56 0 76.861 14TH 56 0 76.861
13TH 52.5 0 76.0178 13TH 52.5 0 76.0178
12TH 49 0 75.1334 12TH 49 0 75.1334
11TH 45.5 0 74.2025 11TH 45.5 0 74.2025
10TH 42 0 73.2189 10TH 42 0 73.2189
9TH 38.5 0 72.1747 9TH 38.5 0 72.1747
8TH 35 0 71.0601 8TH 35 0 71.0601
7TH 31.5 0 69.8626 7TH 31.5 0 69.8626
6TH 28 0 68.5656 6TH 28 0 68.5656
5TH 24.5 0 67.1463 5TH 24.5 0 67.1463
4TH 21 0 65.5729 4TH 21 0 65.5729
3RD 17.5 0 63.7974 3RD 17.5 0 63.7974
2ND 14 0 61.743 2ND 14 0 61.743
MEZZANIN MEZZANIN
10.5 0 59.2716 10.5 0 59.2716
E E
GROUND 7 0 68.7932 GROUND 7 0 68.7932
2ND 2ND
3.5 0 65.6332 3.5 0 65.6332
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 19 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 36.763 -39.8323 RD2 70 36.763 39.8323
RD1 66.5 73.082 -79.1835 RD1 66.5 73.082 79.1835
RD 63 72.3963 -78.4405 RD 63 72.3963 78.4405
15TH 59.5 77.8004 -77.6674 15TH 59.5 77.8004 77.6674
14TH 56 76.9927 -76.861 14TH 56 76.9927 76.861
13TH 52.5 76.148 -76.0178 13TH 52.5 76.148 76.0178
12TH 49 75.262 -75.1334 12TH 49 75.262 75.1334
11TH 45.5 74.3295 -74.2025 11TH 45.5 74.3295 74.2025
10TH 42 73.3442 -73.2189 10TH 42 73.3442 73.2189
9TH 38.5 72.2983 -72.1747 9TH 38.5 72.2983 72.1747
8TH 35 71.1818 -71.0601 8TH 35 71.1818 71.0601
7TH 31.5 69.9823 -69.8626 7TH 31.5 69.9823 69.8626
6TH 28 68.683 -68.5656 6TH 28 68.683 68.5656
5TH 24.5 67.2613 -67.1463 5TH 24.5 67.2613 67.1463
4TH 21 65.6852 -65.5729 4TH 21 65.6852 65.5729
3RD 17.5 63.9067 -63.7974 3RD 17.5 63.9067 63.7974
2ND 14 61.8487 -61.743 2ND 14 61.8487 61.743
MEZZANIN MEZZANIN
10.5 59.3731 -59.2716 10.5 59.3731 59.2716
E E
GROUND 7 64.95 -68.7932 GROUND 7 64.95 68.7932
2ND 2ND
3.5 61.9665 -65.6332 3.5 61.9665 65.6332
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 20 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 27.5968 -29.9008 RD2 70 27.5968 -29.9008
RD1 66.5 54.8602 -59.4404 RD1 66.5 54.8602 -59.4404
RD 63 54.3455 -58.8827 RD 63 54.3455 -58.8827
15TH 59.5 58.4022 -58.3023 15TH 59.5 58.4022 -58.3023
14TH 56 57.7958 -57.697 14TH 56 57.7958 -57.697
13TH 52.5 57.1617 -57.064 13TH 52.5 57.1617 -57.064
12TH 49 56.4967 -56.4001 12TH 49 56.4967 -56.4001
11TH 45.5 55.7967 -55.7013 11TH 45.5 55.7967 -55.7013
10TH 42 55.0571 -54.963 10TH 42 55.0571 -54.963
9TH 38.5 54.2719 -54.1791 9TH 38.5 54.2719 -54.1791
8TH 35 53.4338 -53.3425 8TH 35 53.4338 -53.3425
7TH 31.5 52.5334 -52.4436 7TH 31.5 52.5334 -52.4436
6TH 28 51.558 -51.4699 6TH 28 51.558 -51.4699
5TH 24.5 50.4908 -50.4045 5TH 24.5 50.4908 -50.4045
4TH 21 49.3077 -49.2234 4TH 21 49.3077 -49.2234
3RD 17.5 47.9726 -47.8906 3RD 17.5 47.9726 -47.8906
2ND 14 46.4278 -46.3484 2ND 14 46.4278 -46.3484
MEZZANIN MEZZANIN
10.5 44.5694 -44.4932 10.5 44.5694 -44.4932
E E
GROUND 7 48.7558 -51.6407 GROUND 7 48.7558 -51.6407
2ND 2ND
3.5 46.5162 -49.2686 3.5 46.5162 -49.2686
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 21 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir Story Elevation X-Dir Y-Dir

m kN kN m kN kN
RD2 70 27.5968 29.9008 RD2 70 27.5968 29.9008
RD1 66.5 54.8602 59.4404 RD1 66.5 54.8602 59.4404
RD 63 54.3455 58.8827 RD 63 54.3455 58.8827
15TH 59.5 58.4022 58.3023 15TH 59.5 58.4022 58.3023
14TH 56 57.7958 57.697 14TH 56 57.7958 57.697
13TH 52.5 57.1617 57.064 13TH 52.5 57.1617 57.064
12TH 49 56.4967 56.4001 12TH 49 56.4967 56.4001
11TH 45.5 55.7967 55.7013 11TH 45.5 55.7967 55.7013
10TH 42 55.0571 54.963 10TH 42 55.0571 54.963
9TH 38.5 54.2719 54.1791 9TH 38.5 54.2719 54.1791
8TH 35 53.4338 53.3425 8TH 35 53.4338 53.3425
7TH 31.5 52.5334 52.4436 7TH 31.5 52.5334 52.4436
6TH 28 51.558 51.4699 6TH 28 51.558 51.4699
5TH 24.5 50.4908 50.4045 5TH 24.5 50.4908 50.4045
4TH 21 49.3077 49.2234 4TH 21 49.3077 49.2234
3RD 17.5 47.9726 47.8906 3RD 17.5 47.9726 47.8906
2ND 14 46.4278 46.3484 2ND 14 46.4278 46.3484
MEZZANIN MEZZANIN
10.5 44.5694 44.4932 10.5 44.5694 44.4932
E E
GROUND 7 48.7558 51.6407 GROUND 7 48.7558 51.6407
2ND 2ND
3.5 46.5162 49.2686 3.5 46.5162 49.2686
BASEMENT BASEMENT
Base 0 0 0 Base 0 0 0

Page 22 of 32
 30 Nov 2018

UBC 97 Auto Seismic Load Calculation

This calculation presents the automatically generated lateral seismic loads for load pattern EQXPE according to
UBC 97, as calculated by ETABS.
Direction and Eccentricity

Direction = Multiple

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] C = 0.03ft

Structure Height Above Base, hn h = 206.69 ft
Approximate Fundamental Period, Ta [UBC
T =C( T = 1.635 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3T
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SD
Seismic Source Type = A
Closest Source Distance = 1 km
Near-Source Factor, Na [UBC Table 16-S] N = 1.5
Near-Source Factor, Nv [UBC Table 16-T] N =2
Site Coefficient, Ca [UBC Table 16-Q] C = 0.66
Site Coefficient, Cv [UBC Table 16-R] C = 1.28

Equivalent Lateral Forces

C I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5C I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.194118
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11C I = 0.0726
0.8ZN I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.075294
R
min ≤ V ≤ max

Calculated Base Shear

Period
W V Ft
Direction Used Vcoeff
(kN) (kN) (kN)
(sec)
273547.135
X 0.001 0 53100.3262 0
1
273547.135
X + Ecc. Y 0.001 0 53100.3262 0
1

Applied Story Forces

Page 24 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir

m kN kN
RD2 70 4244.337 0
RD1 66.5 5049.182 0
RD 63 4752.1713 0
15TH 59.5 4859.1638 0
14TH 56 4541.7198 0
13TH 52.5 4224.0592 0
12TH 49 3906.4572 0
11TH 45.5 3580.9191 0
10TH 42 3257.7762 0
9TH 38.5 2934.5522 0
8TH 35 2608.4908 0
7TH 31.5 2284.1663 0
6TH 28 1959.6108 0
5TH 24.5 1637.0637 0
4TH 21 1313.3309 0
3RD 17.5 985.8973 0
2ND 14 653.9968 0
MEZZANI
10.5 307.4318 0
NE
GROUND 7 0 0
2ND
BASEME 3.5 0 0
NT
Base 0 0 0

Page 25 of 32
 30 Nov 2018

UBC 97 Auto Seismic Load Calculation

This calculation presents the automatically generated lateral seismic loads for load pattern EQYPE according to
UBC 97, as calculated by ETABS.
Direction and Eccentricity

Direction = Multiple

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] C = 0.03ft

Structure Height Above Base, hn h = 206.69 ft
Approximate Fundamental Period, Ta [UBC
T =C( T = 1.635 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3T
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SD
Seismic Source Type = A
Closest Source Distance = 1 km
Near-Source Factor, Na [UBC Table 16-S] N = 1.5
Near-Source Factor, Nv [UBC Table 16-T] N =2
Site Coefficient, Ca [UBC Table 16-Q] C = 0.66
Site Coefficient, Cv [UBC Table 16-R] C = 1.28

Equivalent Lateral Forces

C I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5C I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.194118
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11C I = 0.0726
0.8ZN I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.075294
R
min ≤ V ≤ max

Calculated Base Shear

Period
W V Ft
Direction Used Vcoeff
(kN) (kN) (kN)
(sec)
273547.135
Y 0.001 0 53100.3262 0
1
273547.135
Y + Ecc. X 0.001 0 53100.3262 0
1

Applied Story Forces

Page 26 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir

m kN kN
RD2 70 0 4244.337
RD1 66.5 0 5049.182
RD 63 0 4752.1713
15TH 59.5 0 4859.1638
14TH 56 0 4541.7198
13TH 52.5 0 4224.0592
12TH 49 0 3906.4572
11TH 45.5 0 3580.9191
10TH 42 0 3257.7762
9TH 38.5 0 2934.5522
8TH 35 0 2608.4908
7TH 31.5 0 2284.1663
6TH 28 0 1959.6108
5TH 24.5 0 1637.0637
4TH 21 0 1313.3309
3RD 17.5 0 985.8973
2ND 14 0 653.9968
MEZZANI
10.5 0 307.4318
NE
GROUND 7 0 0
2ND
BASEME 3.5 0 0
NT
Base 0 0 0

Page 27 of 32
 30 Nov 2018

UBC 97 Auto Seismic Load Calculation

This calculation presents the automatically generated lateral seismic loads for load pattern EQXNE according to
UBC 97, as calculated by ETABS.
Direction and Eccentricity

Direction = Multiple

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] C = 0.03ft

Structure Height Above Base, hn h = 206.69 ft
Approximate Fundamental Period, Ta [UBC
T =C( T = 1.635 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3T
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SD
Seismic Source Type = A
Closest Source Distance = 1 km
Near-Source Factor, Na [UBC Table 16-S] N = 1.5
Near-Source Factor, Nv [UBC Table 16-T] N =2
Site Coefficient, Ca [UBC Table 16-Q] C = 0.66
Site Coefficient, Cv [UBC Table 16-R] C = 1.28

Equivalent Lateral Forces

C I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5C I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.194118
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11C I = 0.0726
0.8ZN I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.075294
R
min ≤ V ≤ max

Calculated Base Shear

Period
W V Ft
Direction Used Vcoeff
(kN) (kN) (kN)
(sec)
273547.135
X 0.001 0 53100.3262 0
1
273547.135
X - Ecc. Y 0.001 0 53100.3262 0
1

Applied Story Forces

Page 28 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir

m kN kN
RD2 70 4244.337 0
RD1 66.5 5049.182 0
RD 63 4752.1713 0
15TH 59.5 4859.1638 0
14TH 56 4541.7198 0
13TH 52.5 4224.0592 0
12TH 49 3906.4572 0
11TH 45.5 3580.9191 0
10TH 42 3257.7762 0
9TH 38.5 2934.5522 0
8TH 35 2608.4908 0
7TH 31.5 2284.1663 0
6TH 28 1959.6108 0
5TH 24.5 1637.0637 0
4TH 21 1313.3309 0
3RD 17.5 985.8973 0
2ND 14 653.9968 0
MEZZANI
10.5 307.4318 0
NE
GROUND 7 0 0
2ND
BASEME 3.5 0 0
NT
Base 0 0 0

Page 29 of 32
 30 Nov 2018

UBC 97 Auto Seismic Load Calculation

This calculation presents the automatically generated lateral seismic loads for load pattern EQYNE according to
UBC 97, as calculated by ETABS.
Direction and Eccentricity

Direction = Multiple

Eccentricity Ratio = 5% for all diaphragms

Structural Period

Period Calculation Method = Program Calculated

Coefficient, Ct [UBC 1630.2.2] C = 0.03ft

Structure Height Above Base, hn h = 206.69 ft
Approximate Fundamental Period, Ta [UBC
T =C( T = 1.635 sec
1630.2.2 Eq. 30-8]
Program Calculated Period, T [UBC
T ≤ 1.3T
1630.2.2.2]

Factors and Coefficients

Response Modification Factor, R [UBC Table 16-N] R = 8.5

Importance Factor, I [UBC Table 16-K] I=1
Seismic Zone Factor, Z [UBC Table 16-I] Z = 0.4
Soil Profile [UBC Table 16-J] = SD
Seismic Source Type = A
Closest Source Distance = 1 km
Near-Source Factor, Na [UBC Table 16-S] N = 1.5
Near-Source Factor, Nv [UBC Table 16-T] N =2
Site Coefficient, Ca [UBC Table 16-Q] C = 0.66
Site Coefficient, Cv [UBC Table 16-R] C = 1.28

Equivalent Lateral Forces

C I
Base Shear Coefficient [UBC 1630.2.1, Eq. 30-4] =
RT
2.5C I
maximum [UBC 1630.2.1, Eq. 30-5] = = 0.194118
R
minimum [UBC 1630.2.1, Eq. 30-6] = 0.11C I = 0.0726
0.8ZN I
Zone 4 minimum [UBC 1630.2.1, Eq. 30-7] = = 0.075294
R
min ≤ V ≤ max

Calculated Base Shear

Period
W V Ft
Direction Used Vcoeff
(kN) (kN) (kN)
(sec)
273547.135
Y 0.001 0 53100.3262 0
1
273547.135
Y - Ecc. X 0.001 0 53100.3262 0
1

Applied Story Forces

Page 30 of 32
 30 Nov 2018

Story Elevation X-Dir Y-Dir

m kN kN
RD2 70 0 4244.337
RD1 66.5 0 5049.182
RD 63 0 4752.1713
15TH 59.5 0 4859.1638
14TH 56 0 4541.7198
13TH 52.5 0 4224.0592
12TH 49 0 3906.4572
11TH 45.5 0 3580.9191
10TH 42 0 3257.7762
9TH 38.5 0 2934.5522
8TH 35 0 2608.4908
7TH 31.5 0 2284.1663
6TH 28 0 1959.6108
5TH 24.5 0 1637.0637
4TH 21 0 1313.3309
3RD 17.5 0 985.8973
2ND 14 0 653.9968
MEZZANI
10.5 0 307.4318
NE
GROUND 7 0 0
2ND
BASEME 3.5 0 0
NT
Base 0 0 0

Page 31 of 32
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

C1

Column Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT C2 2 C1 FDN TO GR 3500 1 Sway Special

Section Properties
b (mm) h (mm) dc (mm) Cover (Torsion) (mm)
600 1000 60 27.3

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.85 0.6 0.85

Longitudinal Reinforcement Design for Pu - Mu2 - Mu3 Interaction

Rebar Area Rebar
Column End
mm² %
Top 6000 1
Bottom 6000 1

Design Axial Force & Biaxial Moment for Pu - Mu2 - Mu3 Interaction
Design Pu Design Mu2 Design Mu3 Station Loc
Column End Controlling Combo
kN kN-m kN-m mm
kN kN-m kN-m mm
Top -16.6261 0 0.7522 2800 ULT31 1.20DL-1.00EQY+Ortho
Bottom 27.7102 0 1.2537 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

Rebar Av /s Design Vu2 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 428.43 124.9502 2800 ULT31 1.20DL-1.00EQY+Ortho
Bottom 428.43 124.9502 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Minor Shear, Vu3

Rebar Av /s Design Vu3 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 2147.46 359.7918 2800 ULT31 1.20DL-1.00EQY+Ortho
Bottom 2147.46 359.7918 0 ULT31 1.20DL-1.00EQY+Ortho

Joint Shear Check/Design

Shear Shear Joint
Joint Shear Controlling
Vu,Tot Vc Area
Ratio Combo
kN kN mm²
Major(Vu2) 0.229 749.443 3268.4818 600000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
Minor(Vu3) 0.229 1823.1661 3105.0577 570000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

C2

Column Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT C1 162 C2 FDN TO GR 3500 1 Sway Special

Section Properties
b (mm) h (mm) dc (mm) Cover (Torsion) (mm)
850 900 60 27.3

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.85 0.6 0.85

Longitudinal Reinforcement Design for Pu - Mu2 - Mu3 Interaction

Rebar Area Rebar
Column End
mm² %
Top 7650 1
Bottom 7650 1

Design Axial Force & Biaxial Moment for Pu - Mu2 - Mu3 Interaction
Design Pu Design Mu2 Design Mu3 Station Loc
Column End Controlling Combo
kN kN-m kN-m mm
kN kN-m kN-m mm
Top -22.2078 0 0.9381 2850 ULT31 1.20DL-1.00EQY+Ortho
Bottom 35.3305 0 1.4925 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

Rebar Av /s Design Vu2 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 857.85 223.5747 2850 ULT31 1.20DL-1.00EQY+Ortho
Bottom 857.85 223.5747 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Minor Shear, Vu3

Rebar Av /s Design Vu3 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 565.77 138.6749 2850 ULT31 1.20DL-1.00EQY+Ortho
Bottom 565.77 138.6749 0 ULT31 1.20DL-1.00EQY+Ortho

Joint Shear Check/Design

Shear Shear Joint
Joint Shear Controlling
Vu,Tot Vc Area
Ratio Combo
kN kN mm²
Major(Vu2) 0.308 1283.9771 4167.3143 765000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
Minor(Vu3) 0.308 826.1283 4167.3143 765000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Column Section Design

C3
Column Element Details (Envelope)
Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT C11 202 C3 FDN TO GR 3500 1 Sway Special

Section Properties
b (mm) h (mm) dc (mm) Cover (Torsion) (mm)
550 600 60 27.3

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.85 0.6 0.85

Longitudinal Reinforcement Design for Pu - Mu2 - Mu3 Interaction

Rebar Area Rebar
Column End
mm² %
Top 3300 1
Bottom 3300 1

Design Axial Force & Biaxial Moment for Pu - Mu2 - Mu3 Interaction
Design Pu Design Mu2 Design Mu3 Station Loc
Column End Controlling Combo
kN kN-m kN-m mm
kN kN-m kN-m mm
Top -10.0153 0 0.3329 2900 ULT31 1.20DL-1.00EQY+Ortho
Bottom 15.2406 0 0.5067 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

Rebar Av /s Design Vu2 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 0.18 0.0304 2900 ULT31 1.20DL-1.00EQY+Ortho
Bottom 0.18 0.0304 0 ULT31 1.20DL-1.00EQY+Ortho

Shear Reinforcement for Minor Shear, Vu3

Rebar Av /s Design Vu3 Station Loc
Column End Controlling Combo
mm²/m kN mm
Top 0.19 0.0285 2900 ULT31 1.20DL-1.00EQY+Ortho
Bottom 0.19 0.0285 0 ULT31 1.20DL-1.00EQY+Ortho

Joint Shear Check/Design

Shear Shear Joint
Joint Shear Controlling
Vu,Tot Vc Area
Ratio Combo
kN kN mm²
Major(Vu2) 9.261E-05 0.1665 1797.665 330000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
Minor(Vu3) 9.261E-05 0.1561 1797.665 330000 ULT12 1.20DL+f1LL+1.00EQX+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B194 647 2CB1 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 686 0.38 624 0.35 224 0.12
Bot (-2 Axis) 451 0.25 224 0.12 224 0.12

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -134.4457 0 -92.4349 750
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 67.2229 0 33.6114 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-33.6114 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
33.6114 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
861.02 864.73 837.76

Design Shear Force for Major Shear, Vu2 (Part 1 of 2)

End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
144.258 0 0.1449 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 Design Shear Force for Major Shear, Vu2 (Part 2 of 2)
End-J End-J
Design Vu Station Loc
kN mm
140.3612 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
732.39 1058

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
41.6788 1125 41.6788 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B148 577 2CB2 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 847 0.47 592 0.33 276 0.15
Bot (-2 Axis) 556 0.31 276 0.15 276 0.15

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -165.0926 475 -87.8009 1125
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 82.5463 475 41.2732 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-41.2732 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
41.2732 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
118.4778 475 475 -87.8009 64.6712 1875
ULT1 1.40DL 64.6712 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2871.92 4148

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
163.4357 1125 163.4357 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B62 591 2G2 4000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
400 600 400 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 185 0.08 47 0.02 188 0.08
Bot (-2 Axis) 92 0.04 163 0.07 94 0.04

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -27.7339 300 -7.0659 2662.5
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 13.8669 300 24.4888 1987.5
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-28.2634 3700
ULT18 1.20DL+f1LL-1.00EQY+Ortho
14.1317 3700
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
387.3 387.3 387.3
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
53.2612 760 0.0475 2662.5
ULT31 1.20DL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
64.966 3700
ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
43.7872 760 43.7872 760
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B41 605 2PGT5 9400 0.949 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 633 0.3 633 0.3 1994 0.95
Bot (-2 Axis) 732 0.35 1027 0.49 964 0.46

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -93.9944 2333.3 -93.9944 6983.3
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 111.4168 2333.3 199.8056 5500
Combo ULT2 1.20DL+1.60LL ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-375.9775 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho
187.9888 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
96.0568 2333.3 2333.3 -93.9944 91.6342 7466.7
ULT1 1.40DL 96.0568 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2906.96 4490

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
204.6126 9400 204.6126 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B49 615 2TB1 3022 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 650 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 296 0.15 567 0.29 908 0.47
Bot (-2 Axis) 296 0.15 364 0.19 596 0.31

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -48.3737 500 -92.1557 2159.8
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 48.3737 500 59.4283 1000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-193.4947 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho
96.7474 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
965.61 965.61 965.61
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
43.4524 0 500 -92.1557 176.7597 3022
ULT1 1.40DL 176.7597 ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2157.05 3331

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
134.7625 1000 134.7625 1000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND B185 637 2TB2 2888.8 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 350 250 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 379 0.43 182 0.21 123 0.14
Bot (-2 Axis) 249 0.28 153 0.17 281 0.32

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -39.6995 0 -14.579 962.9
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 19.8498 0 12.2662 1925.9
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-9.9249 2407.4
ULT18 1.20DL+f1LL-1.00EQY+Ortho
27.3155 2888.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
673.43 673.43 673.43
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
60.5931 0 0 -14.579 48.7247 2407.4
ULT1 1.40DL 60.5931 ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
601.16 508

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
13.3374 2888.8 13.3374 2888.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
3RD B148 260 3CB1 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 885 0.49 620 0.34 288 0.16
Bot (-2 Axis) 580 0.32 288 0.16 288 0.16

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -172.2269 475 -91.8906 1125
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 86.1134 475 43.0567 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-43.0567 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
43.0567 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
122.5159 475 475 -91.8906 67.5025 1875
ULT1 1.40DL 67.5025 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
3117.85 4503

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
177.4309 1125 177.4309 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
3RD B132 658 3CB3 2300 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 316 0.18 567 0.31 973 0.54
Bot (-2 Axis) 316 0.18 316 0.18 627 0.35

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -47.1897 383.3 -84.1701 1150
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 47.1897 383.3 47.1897 1150
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-188.7587 1900
ULT18 1.20DL+f1LL-1.00EQY+Ortho
94.3794 1900
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
51.4086 0 383.3 -84.1701 128.5009 1525
ULT1 1.40DL 128.5009 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2381.27 3440

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
135.5138 1900 135.5138 1900
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
3RD B41 687 3PTG5 9400 0.947 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 648 0.31 648 0.31 2043 0.97
Bot (-2 Axis) 720 0.34 1109 0.53 987 0.47

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -96.1616 2333.3 -96.1616 6983.3
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 106.674 2333.3 215.2386 6500
Combo ULT2 1.20DL+1.60LL ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-384.6462 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho
192.3231 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J

Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m

338.89 338.89 338.89

 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
97.938 2333.3 2333.3 -96.1616 113.2064 7466.7
ULT1 1.40DL 97.938 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
3029.16 4678

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
213.2137 9400 213.2137 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
3RD B185 719 3TB1 2888.8 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 650 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 686 0.35 327 0.17 191 0.1
Bot (-2 Axis) 384 0.2 197 0.1 539 0.28

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -125.306 0 -53.3787 962.9
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 62.653 0 32.224 1925.9
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-31.3265 2407.4
ULT18 1.20DL+f1LL-1.00EQY+Ortho
87.5482 2888.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
1113.25 1113.25 1113.25
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
203.7865 0 0 -53.3787 183.403 2407.4
ULT12 1.20DL+f1LL+1.00EQX+Ortho 203.7865 ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
802.42 1239

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
50.1313 2888.8 50.1313 2888.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
3RD B188 723 3TB2 2300 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 350 250 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 181 0.21 281 0.32 563 0.64
Bot (-2 Axis) 181 0.21 181 0.21 281 0.32

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -14.5098 297 -28.4357 1352.2
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 14.5098 297 14.5098 1352.2
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-58.0393 2300
ULT18 1.20DL+f1LL-1.00EQY+Ortho
29.0197 2300
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
13.578 0 297 -28.4357 27.2381 1826.1
ULT1 1.40DL 27.2381 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1729.41 1460

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
38.3691 1352.2 38.3691 1352.2
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B47 1890 DTB-1 3000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 550 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 715 0.43 360 0.22 486 0.29
Bot (-2 Axis) 469 0.28 233 0.14 241 0.15

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -126.6536 0 -48.7811 1000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT1 1.40DL
Bot (-2 Axis) 63.3268 0 31.6634 2000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-65.525 3000
ULT18 1.20DL+f1LL-1.00EQY+Ortho
32.7625 3000
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
907.7 879.06 686.25
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle End-J
Design Vu Station Loc Design Vu Station Loc Design Vu
kN mm kN mm kN
137.9971 0 0.1336 1000 104.3301
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J
Station Loc
mm
3000

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
22.3917 1000 22.3917 1000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B101 1900 DTB2 2900 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 350 200 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 74 0.11 93 0.13 225 0.32
Bot (-2 Axis) 225 0.32 123 0.18 148 0.21

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -5.9412 483.3 -7.4769 1933.3
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 19.4213 0 9.8399 966.7
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-23.7646 2900
ULT18 1.20DL+f1LL-1.00EQY+Ortho
11.8823 2900
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
7.8471 0 483.3 -7.4769 14.5741 2416.7
ULT1 1.40DL 14.5741 ULT10 1.20DL+f1LL+1.00WY

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
684.64 510

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
10.4752 1933.3 10.4752 1933.3
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B188 1911 DTB-3 2300 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 550 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 301 0.18 660 0.4 930 0.56
Bot (-2 Axis) 301 0.18 301 0.18 569 0.35

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -40.8256 297 -117.2322 1541.7
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 40.8256 297 40.8256 1541.7
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-163.3023 2300
ULT18 1.20DL+f1LL-1.00EQY+Ortho
81.6512 2300
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
43.9202 0 297 -117.2322 52.8929 1920.9
ULT1 1.40DL 52.8929 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2193.32 2949

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
112.6071 1541.7 112.6071 1541.7
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B171 575 EB1 4325.5 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 300 200 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 376 0.63 246 0.41 121 0.2
Bot (-2 Axis) 186 0.31 121 0.2 186 0.31

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -32.0313 0 -21.3503 1081.4
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 16.0157 0 8.0078 3244.1
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-8.0078 3965
ULT18 1.20DL+f1LL-1.00EQY+Ortho
16.0825 4325.5
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
353.27 397.93 325.82

Design Shear Force for Major Shear, Vu2 (Part 1 of 2)

End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
26.3057 0 0.0296 1081.4
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 Design Shear Force for Major Shear, Vu2 (Part 2 of 2)
End-J End-J
Design Vu Station Loc
kN mm
24.2613 3604.6
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
2.1178 2162.7 2.1178 2162.7
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B49 349 GG1 3022 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
450 600 450 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 403 0.15 814 0.3 1238 0.46
Bot (-2 Axis) 403 0.15 461 0.17 813 0.3

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -60.3774 500 -120.8893 2159.8
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 60.3774 500 68.9821 1000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-241.5097 3022
ULT7 1.20DL+1.60LL-0.50WY
120.7548 3022
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
v1236.59 1236.59 1236.59

Design Shear Force for Major Shear, Vu2

End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
54.4903 0 500 -120.8893 207.1821 3022
ULT1 1.40DL 207.1821 ULT31 1.20DL-1.00EQY+Ortho
 Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1849.09 3226

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
179.9994 1000 179.9994 1000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B62 362 GG-2 4000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
450 600 450 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 443 0.16 110 0.04 439 0.16
Bot (-2 Axis) 221 0.08 572 0.21 219 0.08

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -66.3116 300 -16.5779 2662.5
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 33.1558 300 85.3885 2000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-65.7085 3700
ULT7 1.20DL+1.60LL-0.50WY
32.8542 3700
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
435.71 435.71 435.71
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle End-J
Design Vu Station Loc Design Vu Station Loc Design Vu
kN mm kN mm kN
109.5143 760 0.0922 2662.5 122.9752
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J
Station Loc
mm
3700

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1100.67 1920

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
107.1448 760 107.1448 760
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B27 327 GG-3 4000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 550 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 244 0.13 61 0.03 202 0.11
Bot (-2 Axis) 122 0.06 490 0.25 130 0.07

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -33.21 275 -8.3025 2500
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 16.605 275 66.2226 2000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-27.5131 3500
ULT7 1.20DL+1.60LL-0.50WY
17.7654 3000
ULT2 1.20DL+1.60LL

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
338.89 338.89 338.89
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
46.057 1000 0.0783 2500
ULT31 1.20DL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
71.705 3500
ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
31.0681 3500 31.0681 3500
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B57 357 GG-4 4600 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 221 0.11 72 0.03 291 0.14
Bot (-2 Axis) 110 0.05 691 0.33 229 0.11

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -33.1059 275 -10.89 3066.7
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 16.5529 275 102.4977 2300
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-43.56 4100
ULT7 1.20DL+1.60LL-0.50WY
34.3004 3450
ULT2 1.20DL+1.60LL

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
338.89 338.89 338.89
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
37.5048 1150 0.068 3066.7
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
123.7305 3450
ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
997.14 1540

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
70.1859 4100 70.1859 4100
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B71 371 GPTB5 9700 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 484 0.27 120 0.07 392 0.22
Bot (-2 Axis) 241 0.13 452 0.25 195 0.11

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -72.0566 0 -18.0141 7150
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 36.0283 0 67.3151 3907.3
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-58.4138 9700
ULT7 1.20DL+1.60LL-0.50WY
29.2069 9700
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J

Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m

0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
56.7541 0 0 -18.0141 34.4455 7572
ULT2 1.20DL+1.60LL 34.4455 ULT2 1.20DL+1.60LL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1118.87 1616

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
63.6729 7993.9 63.6729 7993.9
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B3 303 GPTG5 13000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 720 0.34 223 0.11 732 0.35
Bot (-2 Axis) 357 0.17 732 0.35 448 0.21

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -106.8048 0 -33.3933 9400
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 53.4024 0 108.8483 8433.3
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-128.5128 13000
ULT18 1.20DL+f1LL-1.00EQY+Ortho
66.7866 13000
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
27.0677 0 0 -33.3933 31.6937 9760
ULT1 1.40DL 31.6937 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2130.77 3291

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
149.9791 3250 149.9791 3250
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B36 336 GTB1 3000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 650 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 1535 0.79 1347 0.69 1597 0.82
Bot (-2 Axis) 747 0.38 511 0.26 776 0.4

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -320.0244 0 -282.6324 2000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 160.0122 0 83.0556 2000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-332.2224 3000
ULT7 1.20DL+1.60LL-0.50WY
166.1112 3000
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
1477.03 1478.55 1514.19
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
270.3786 0 0.2707 2000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
277.1815 3000
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
31.7823 1000 31.7823 1000
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B104 408 GTB2 2900 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 350 250 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 159 0.18 254 0.29 493 0.56
Bot (-2 Axis) 343 0.39 169 0.19 281 0.32

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -12.774 483.3 -20.284 1933.3
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 35.9915 0 13.5161 966.7
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-51.0962 2900
ULT7 1.20DL+1.60LL-0.50WY
24.2619 2900
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
805.69 805.69 805.69
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
22.0545 0 483.3 -20.284 72.4934 2900
ULT2 1.20DL+1.60LL 72.4934 ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
819.34 692

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
18.178 966.7 18.178 966.7
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B37 337 GTB3 9400 0.953 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 1620 0.77 519 0.25 908 0.43
Bot (-2 Axis) 820 0.39 1234 0.59 596 0.28

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -309.3478 500 -77.337 6983.3
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 160.562 2527.8 238.5734 4333.3
Combo ULT2 1.20DL+1.60LL ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-177.3578 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho
88.6789 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
338.89 338.89 338.89
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle End-J
Design Vu Station Loc Design Vu Station Loc Design Vu
kN mm kN mm kN
180.8425 500 0.1167 6983.3 130.1287
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J
Station Loc
mm
9400

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1309.03 2022

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
92.1386 1083.3 92.1386 1083.3
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B107 411 GTB4 9400 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 891 0.42 291 0.14 409 0.19
Bot (-2 Axis) 586 0.28 890 0.42 563 0.27

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -174.2415 0 -43.5604 6983.3
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 87.1208 0 173.9983 5416.7
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-61.0954 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho
83.8023 7466.7
ULT2 1.20DL+1.60LL

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
338.89 338.89 338.89
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
111.2501 2166.7 0.0738 4333.3
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
36.2409 9400
ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
29.2941 9400 29.2941 9400
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B50 288 MB-2 8622 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 450 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 376 0.28 97 0.07 394 0.29
Bot (-2 Axis) 187 0.14 166 0.12 195 0.14

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -40.4013 0 -10.5586 6100
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 20.2007 0 17.9425 4100
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-42.2345 8622
ULT18 1.20DL+f1LL-1.00EQY+Ortho
21.1172 8622
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
290.47 290.47 290.47
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
19.5645 2140 0.0178 6100
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
39.8316 7759.8
ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
728.16 833

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
29.2769 8622 29.2769 8622
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B148 551 MCB2 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 634 0.3 291 0.14 157 0.07
Bot (-2 Axis) 315 0.15 157 0.07 157 0.07

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -94.227 500 -43.6179 1125
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 47.1135 500 23.5567 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-23.5567 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
23.5567 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J

Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m

807.57 807.57 807.57

 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
79.5574 500 500 -43.6179 135.3016 1875
ULT1 1.40DL 135.3016 ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1793.95 2771

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
126.2708 1125 126.2708 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B127 298 MCB1 2300 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 550 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 235 0.14 196 0.12 133 0.08
Bot (-2 Axis) 117 0.07 59 0.04 59 0.04

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -31.9835 0 -26.638 766.7
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 15.9918 0 7.9959 1533.3
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-18.1104 1916.7
ULT7 1.20DL+1.60LL-0.50WY
8.029 2300
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
290.47 290.47 290.47
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle End-J
Design Vu Station Loc Design Vu Station Loc Design Vu
kN mm kN mm kN
37.6823 383.3 0.008 1533.3 4.4601
ULT31 1.20DL-1.00EQY+Ortho ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J
Station Loc
mm
2300

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
16.1176 1150 16.1176 1150
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B173 561 MCB1A 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 450 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 436 0.28 272 0.17 108 0.07
Bot (-2 Axis) 216 0.14 108 0.07 108 0.07

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -46.8197 0 -29.3385 750
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 23.4099 0 11.7049 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-11.7049 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
11.7049 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
543.07 510.41 442.03
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
65.713 0 0.0618 750
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
53.4873 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
519.96 647

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
25.8573 1125 25.8573 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B155 559 MCB3 1900.4 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 100 0.05 171 0.08 404 0.19
Bot (-2 Axis) 100 0.05 100 0.05 201 0.1

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -15.0778 194.3 -25.6715 952.5
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 15.0778 194.3 15.0778 952.5
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-60.3114 1900.4
ULT18 1.20DL+f1LL-1.00EQY+Ortho
30.1557 1900.4
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
9.205 0 194.3 -25.6715 34.5985 1426.4
ULT2 1.20DL+1.60LL 34.5985 ULT2 1.20DL+1.60LL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1270.41 1962

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
89.4208 952.5 89.4208 952.5
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B147 548 MG-3 5777.6 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 800 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 1685 0.6 545 0.19 545 0.19
Bot (-2 Axis) 1003 0.36 656 0.23 655 0.23

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -446.5948 0 -111.6487 4259.1
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 223.2974 0 134.1335 2888.8
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-111.6487 5360.9
ULT18 1.20DL+f1LL-1.00EQY+Ortho
133.7847 4601.6
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
799.51 338.89 338.89
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
391.0488 0 0 -111.6487 19.2812 5777.6
ULT12 1.20DL+f1LL+1.00EQX+Ortho 391.0488 ULT23 0.90DL-1.00WY

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1041.61 2025

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
102.0058 2888.8 102.0058 2888.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B52 550 MG-6 5782.3 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
400 650 400 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 415 0.16 164 0.06 663 0.26
Bot (-2 Axis) 295 0.11 914 0.35 330 0.13

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -67.8021 0 -26.9826 4259.1
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 48.3435 1444.4 151.9747 3231.4
Combo ULT2 1.20DL+1.60LL ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-107.9305 5782.3
ULT18 1.20DL+f1LL-1.00EQY+Ortho
53.9652 5782.3
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
387.3 387.3 387.3
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
26.8575 1444.4 0 -26.9826 141.6359 5782.3
ULT12 1.20DL+f1LL+1.00EQX+Ortho 26.8575 ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1040.84 1816

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
95.8304 2828 95.8304 2828
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B40 282 MPTG5 10000 0.938 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 551 0.26 551 0.26 1723 0.82
Bot (-2 Axis) 732 0.35 1060 0.5 837 0.4

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -81.9498 2350 -81.9498 7037.5
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 127.4517 2350 206.0249 3400
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-327.7991 9500
ULT18 1.20DL+f1LL-1.00EQY+Ortho
163.8996 9500
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
338.89 338.89 338.89
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
103.5477 2350 0.1223 7037.5 236.6656 9012.5
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1209.12 1867

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
85.1066 9500 85.1066 9500
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B49 286 MTB1 3022 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 650 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 686 0.35 906 0.46 2200 1.13
Bot (-2 Axis) 686 0.35 686 0.35 1057 0.54

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -111.9858 500 -192.9713 2159.8
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 111.9858 500 111.9858 2159.8
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-447.9432 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho
223.9716 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m

Design Shear Force for Major Shear, Vu2

End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
36.0341 0 500 -192.9713 276.3799 2590.9
ULT1 1.40DL 276.3799 ULT6 1.20DL+1.60LL+0.50WY
 Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1958.3 3024

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
122.3455 1000 122.3455 1000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
MEZZANINE B126 252 MTB2 2986.8 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
250 350 250 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 97 0.11 157 0.18 297 0.34
Bot (-2 Axis) 187 0.21 97 0.11 195 0.22

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -7.8209 497.8 -12.5538 1991.2
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 14.9695 0 7.8209 1991.2
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-31.2835 2986.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho
15.6417 2986.8
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
6.7792 0 497.8 -12.5538 43.9379 2986.8
ULT10 1.20DL+f1LL+1.00WY 43.9379 ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
512 432

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
11.3592 995.6 11.3592 995.6
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B194 1917 PCB1 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 550 200 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 770 0.7 506 0.46 248 0.23
Bot (-2 Axis) 380 0.35 248 0.23 248 0.23

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -134.0268 0 -89.4284 750
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 67.0134 0 33.5067 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-33.5067 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
33.5067 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
55.0898 0 0 -89.4284 136.192 1875
ULT1 1.40DL 136.192 ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
854.86 978

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
23.0986 1125 23.0986 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B148 1851 PCB2 2250 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
200 550 200 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 745 0.68 413 0.38 240 0.22
Bot (-2 Axis) 380 0.35 240 0.22 240 0.22

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -129.7785 275 -73.5548 1125
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 64.8892 275 32.4446 1500
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-32.4446 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho
32.4446 1875
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
71.9211 275 275 -73.5548 47.1662 1875
ULT1 1.40DL 47.1662 ULT1 1.40DL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
3678.23 4209

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
99.3868 1125 99.3868 1125
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B49 1887 PG1 3022 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 313 0.17 582 0.32 966 0.54
Bot (-2 Axis) 313 0.17 397 0.22 627 0.35

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -46.8518 500 -86.3868 2159.8
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 46.8518 500 59.2303 1000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-187.4071 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho
93.7035 3022
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
1035.82 1035.82 1035.82
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
44.4824 0 500 -86.3868 173.5448 3022
ULT1 1.40DL 173.5448 ULT31 1.20DL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2071.87 2993

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
117.9061 1000 117.9061 1000
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B203 678 PG2 4000 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
300 600 300 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 181 0.1 110 0.06 443 0.25
Bot (-2 Axis) 110 0.06 248 0.14 220 0.12

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -27.0937 0 -16.4832 3000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 16.4832 760 37.1561 2000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-65.9327 4000
ULT18 1.20DL+f1LL-1.00EQY+Ortho
32.9664 4000
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
290.47 290.47 290.47
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle End-J
Design Vu Station Loc Design Vu Station Loc Design Vu
kN mm kN mm kN
56.4169 760 0.0723 3000 77.0736
ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J
Station Loc
mm
4000

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
28.2679 760 28.2679 760
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
RD B38 1874 PPTG5 9400 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 600 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 1298 0.62 419 0.2 419 0.2
Bot (-2 Axis) 732 0.35 732 0.35 419 0.2

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -250.3469 275 -62.5867 6983.3
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
Bot (-2 Axis) 125.1734 275 120.6195 6000
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-62.5867 8916.7
ULT18 1.20DL+f1LL-1.00EQY+Ortho
62.5867 8916.7
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
381.72 0 0
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
172.2891 275 0.1212 2600
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
106.7241 8433.3
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
0 0

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
20.2297 800 20.2297 800
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT18 1.20DL+f1LL-1.00EQY+Ortho
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B65 365 RB-1 4500 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
350 550 350 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 700 0.36 229 0.12 229 0.12
Bot (-2 Axis) 461 0.24 259 0.13 229 0.12

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -124.6343 0 -31.1586 3000
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 62.3172 0 35.2124 2250
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-31.1586 3800
ULT7 1.20DL+1.60LL-0.50WY
31.1586 3800
ULT7 1.20DL+1.60LL-0.50WY

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
90.6074 0 0 -31.1586 8.1476 3375
ULT2 1.20DL+1.60LL 8.1476 ULT2 1.20DL+1.60LL

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
1358.27 1962

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
86.2517 1125 86.2517 1125
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B23 323 RG-1 6500 1 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
400 550 400 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 4 1.904E-03 34 0.02 2 1.056E-03
Bot (-2 Axis) 6 2.529E-03 76 0.03 1 5.282E-04

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -0.5732 966.7 -4.6803 3620
Combo ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 0.7613 1450 10.315 3250
Combo ULT2 1.20DL+1.60LL ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-0.318 5060
ULT18 1.20DL+f1LL-1.00EQY+Ortho
0.159 5420
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 387.3 0
 Design Shear Force for Major Shear, Vu2 (Part 1 of 2)
End-I End-I Middle Middle
Design Vu Station Loc Design Vu Station Loc
kN mm kN mm
3.5856 966.7 0.0061 3620
ULT18 1.20DL+f1LL-1.00EQY+Ortho ULT31 1.20DL-1.00EQY+Ortho

Design Shear Force for Major Shear, Vu2 (Part 2 of 2)

End-J End-J
Design Vu Station Loc
kN mm
2.6777 5060
ULT18 1.20DL+f1LL-1.00EQY+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
620.78 959

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
46.9693 3250 46.9693 3250
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
 ETABS 2016 Concrete Frame Design
ACI 318-14 Beam Section Design

Beam Element Details (Envelope)

Level Element Unique Name Section ID Length (mm) LLRF Type
2ND BASEMENT B30 330 RG-2 13000 0.771 Sway Special

Section Properties
b (mm) h (mm) bf (mm) ds (mm) dct (mm) dcb (mm)
500 700 500 0 60 60

Material Properties
Ec (MPa) f'c (MPa) Lt.Wt Factor (Unitless) fy (MPa) fys (MPa)
30441.74 41.37 1 413.69 413.69

Design Code Parameters

ΦT ΦCTied ΦCSpiral ΦVns ΦVs ΦVjoint
0.9 0.65 0.75 0.75 0.6 0.85

Flexural Reinforcement for Major Axis Moment, Mu3

End-I End-I Middle Middle End-J End-J
Rebar Area Rebar Rebar Area Rebar Rebar Area Rebar
mm² % mm² % mm² %
Top (+2 Axis) 4078 1.17 1239 0.35 1781 0.51
Bot (-2 Axis) 1956 0.56 2736 0.78 1492 0.43

Flexural Design Moment, Mu3 (Part 1 of 2)

End-I End-I Middle Middle
Design Mu Station Loc Design Mu Station Loc
kN-m mm kN-m mm
Top (+2 Axis) -898.8216 300 -224.7054 9750
Combo ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY
Bot (-2 Axis) 449.4108 300 619.0768 6405.9
Combo ULT7 1.20DL+1.60LL-0.50WY ULT2 1.20DL+1.60LL

Flexural Design Moment, Mu3 (Part 2 of 2)

End-J End-J
Design Mu Station Loc
kN-m mm
-410.5336 13000
ULT7 1.20DL+1.60LL-0.50WY
345.7999 10120
ULT2 1.20DL+1.60LL

Shear Reinforcement for Major Shear, Vu2

End-I Middle End-J
Rebar Av /s Rebar Av /s Rebar Av /s
mm²/m mm²/m mm²/m
0 0 0
 Design Shear Force for Major Shear, Vu2
End-I End-I Middle Middle End-J End-J
Design Vu Station Loc Design Vu Station Loc Design Vu Station Loc
kN mm kN mm kN mm
318.4795 300 300 -224.7054 252.3201 10120
ULT12 1.20DL+f1LL+1.00EQX+Ortho 252.3201 ULT12 1.20DL+f1LL+1.00EQX+Ortho

Torsion Reinforcement
Shear Longitudinal
Rebar At /s Rebar Al
mm²/m mm²
2385.64 4877

Design Torsion Force

Design Tu Station Loc Design Tu Station Loc
kN-m mm kN-m mm
316.1146 1083.3 316.1146 1083.3
ULT7 1.20DL+1.60LL-0.50WY ULT7 1.20DL+1.60LL-0.50WY