INSTALLATION AND OPERATING

INSTRUCTIONS

MANUAL TRANSFER SWITCHES

FROM

0
 Residential Wattage Requirements

Appliance Running Add watts

Watts for starting
Furnace blower, gas or fuel
1/8 hp 300 500
1/8 hp 500 750
1/6 hp 500 750
1/4 hp 600 1000
1/3 hp 700 1400
1/2 hp 875 2100
Shallow well pump
1/3 hp 750 1400
1/2 hp 1000 2350
Sump pump
1/3 hp 800 1300
1/2 hp 1050 2150
Refrigerator or freezer 800 2300
Garage door opener
1/4 hp 550 1100
1/3 hp 750 1400
Lights on bulb 0
Radio 50-200 0
Television 100-300 0
Microwave oven 600-1500 0
Coffee maker, typical 1750 0
Toaster/toaster oven 1050-1850 0
Portable heater 1100-1500 0
Dehumidifier 650-800 0
Electric blanket 400 0
Clothes washer 1150 2300
Clothes dryer, gas 700 1800
Dishwasher
cool dry 700 1400
hot dry 1450 1400
Vacuum cleaner 800-1100 0
Hair dryer 300-1500 0
Iron 1200 0

1
 Warnings • Cautions

Warning: Improper installation of this transfer switch

could cause damage or personal injury by electrocution
or fire. Installation must be performed by a qualified
electrician in compliance with all applicable electrical
codes

Warning: When using this product with a portable

generator, do not operate the generator indoors or in an
enclosed area. Do not operate a generator where the
exhaust fumes can accumulate indoors or in an
enclosed area like a garage or close to windows or
doors.

Caution: Reliance transfer switches covered in this

manual should not be used for appliances or systems
that may exceed the capacity of the product.

Caution: When the transfer switch is connected to

branch circuits with AFCI or GFCI breakers, the AFCI
or GFCI protection will be lost when, and only when,
the toggle switch in the transfer switch is in the GEN
position. To get AFCI or GFCI protection when running
on generator power, install the appropriate breakers in
the transfer switch.

Reliance Controls Corporation is not responsible for

damage or injury caused by incorrect installation of
this transfer switch.

Member, National Electrical Manufacturers Association

1
 Reliance Installation and Operating Instructions
Key Components of the Reliance Transfer Switch
Figure 1

Circuit breakers. Each transfer switch circuit has a 1-in interchangeable circuit breaker
that protects the branch circuit when the circuit selector switch is in the GEN position. In
the LINE position, each branch circuit is protected by the breaker in the load center.
Circuit selector switches. These switches allow you to select either GEN (generator) or
LINE (utility) as the power source for the branch circuits that have been wired through the
transfer switch. The OFF position is generally not used, as a switch in the OFF position
removes that branch circuit from both utility and generator power.
Handle ties. Handle ties are used for 240-volt circuits or multi-wire branch circuits. They
may be removed for 120-volt circuits. See page 6 for instructions on removing and adding
handle ties.
Power inlet filler plate. This can be replaced with a power inlet that is included in the
suffix A and B models (see page 7 for installation instructions). The power cord from the
generator is plugged into this inlet. The inlet is supplied separately for indoor models to
encourage the use of a remote connection outdoors reducing the likelihood of running the
generator indoors which is extremely dangerous. If this indoor model is installed outdoors,
make sure it is installed in a dry location.
Circuit Breaker Compartment Cover. Remove to change circuit breakers. Also includes
a wiring space that can be used to hard-wire the unit to a remote power inlet box.
Analog wattmeters (suffix A and C models). These meters indicate the total load, in
watts, on each side of the generator when the generator is supplying power as follows:
The left meter measures the load on The right meter measures the load on
A, C, and E 6-circuit B, D and F 6-circuit
A,C,E, and G 8-circuit B,D,F and H 8-circuit
A, C, E, G and I 10-circuit B, D, F, H and J 10-circuit
Note: The watt meters will register only if power is being used from the generator.
2
 Installation Instructions
Preparing for You will need the following items:
Installation Electric drill
Screwdriver
Wire cutters/stripper
Hammer
Four anchors and screws
6 or 10 yellow wire connectors (depending on the model)
4 red wire connectors for the 20A and 30A hard-wire models

The following five steps generally apply to all transfer switch installations. The transfer
switch may be installed on either side of the load center.
1. Turn off the main circuit breaker in the load center to ensure your
safety.

Danger: All current-carrying parts on the LINE side of the main

are still live

2. Remove the cover of the load Figure 2

center.
3. Locate and remove a knockout (ko)
in the bottom of the load center
(Figure 2). Use a 3/4" ko for 6-circuit
models, and a 1" ko for 10-circuit
models.
4. Insert the wires extending from the
end of the flexible conduit through
the ko. Attach the conduit connector
securely with the locknut provided.
5. Anchor the transfer switch to the
wall using the top bracket and
bottom mounting holes located in the
cabinet behind the wiring
compartment cover. Do not attempt
to bend the flexible conduit beyond
its structural capabilities.

Wiring the Reliance Transfer Switch to the Load Center

Determine which circuits will be used during an emergency. The residential wattage
requirement chart on the inside front cover of this manual may be used as a guide, but
actual appliance wattages may vary. If a selected circuit is part of a multi-wire branch
circuit, ensure the other branch circuit that shares the neutral is also connected to the
transfer switch. The two circuits must be connected to opposing legs (phases) of the
generator power and a handle tie must be installed on the switch handles so that both legs
are transferred at the same time.

3
 Warning: Failure to properly install a multi-wire branch circuit could result in
overloading the neutral wire.
The maximum number of circuits available and those that can be used for multi-wire
branch circuits depends on the model of the transfer switch as follows:
Model Max Available for multi-wire branch circuits
A304 Circ
4 Any two adjacent circuits.
A306, A506 6 Any two adjacent circuits.
A308 8 Any two adjacent circuits.
A310, A510 10 Any two adjacent circuits.

Balancing the Load

To maximize the efficiency of your generator, divide

appliance circuits and others requiring higher wattage
between adjacent circuit selector switches of the
transfer switch so that a usage balance is achieved
between the opposing legs of the generator power.
For example, on a 6-circuit transfer switch, consider
wiring the refrigerator to Switch C and the furnace to
Switch D (Figure 3).

Figure 3

Changing Circuit Breakers

This product is supplied with a combination of 15- and 20-amp circuit breakers. In
some cases, a 30 amp double-pole breaker may be supplied in the A and B positions.
All circuit breaker positions will accommodate 15- and 20-amp circuit breakers, and
may be easily changed in the field. To remove a circuit breaker, remove the circuit
breaker compartment cover, unscrew the terminal screw in the breaker to be removed,
removed the wire, tilt the top of the circuit breaker towards you and lift up and out.
Reverse the procedure to install another breaker. In addition, positions A and B (but
only these positions) will accommodate 30-amp circuit breakers.
This product is UL approved for use with the field-installed breakers listed on the side
of the cabinet: Use 30 amps maximum in positions A and B, 20 amps maximum in all
other positions.
Rating of a transfer switch circuit breaker should not exceed the rating of the
corresponding branch circuit breaker in the load center.
Do not install any breaker larger than 20 amps., except in positions A and B
which may be 30 amps.

4
Installing 120-volt Circuits
Warning: Transfer switch circuits with 20 amp breakers must be installed on only
those branch circuits with 20 amp branch circuit breakers. Transfer switch circuits
with 15 amp breakers can be installed on 15 or 20 amp branch circuits. Do not
install any transfer switch circuit on branch circuits greater than 20 amps,
except in position A and B which maybe 30 amps.
Wire the most critical circuits first, starting with any circuit position on the transfer switch.
Let's assume that Switch C will be designated to supply power to the refrigerator.
1. Turn off the refrigerator circuit breaker. Loosen the screw that secures the wire to the
circuit breaker. Disconnect the wire from the circuit breaker.
2. On the transfer switch, find the black and red wires marked C.
3. Feed the red wire to the selected breaker, in this case the refrigerator breaker.
4. Cut the red wire C to a convenient length. Strip approximately 5/8" from the end of the
wire. Connect the red wire to the refrigerator circuit breaker and retighten the screw.
5. Cut the black wire C to a convenient length for aligning with the wire removed from the
refrigerator circuit breaker in step 1. Strip approximately 5/8" from the end of the wire.
6. Insert both wires (the wire removed from the circuit breaker in step 1 and the black
wire) into a yellow wire connector. Twist the connector tightly and push the wires back
into the wiring compartment of the load center.
This completes the installation of the transfer switch for your refrigerator.
Repeat steps 1-6 for each of the remaining considering the following:
• See the following section for 240-volt circuits and the removal of handle ties if 240-
volt circuits are not required.
• Remember to "balance the load"—dividing the appliances requiring higher
wattage between the left and right sides of the transfer switch.

Figure 4

5
Installing 240-volt Circuits
Any two adjacent circuit selector switches may be used for a double-pole 240-volt circuit.
Use a handle tie to connect the two circuit selector switches.
*Note: Circuits used for multi-wire branch circuits are not available for 240-volt
circuits
Removing handle tie(s). If there are no 240-volt or multi-wire circuits in the transfer
switch installation, handle-ties on the switches are not needed. To remove a handle tie,
place the handle-tied switches in a position opposite of the other switches. Rotate the
cylindrical spacer between the switches upward repeatedly until the threaded shaft is
exposed on the right switch. Grab the threaded shaft and continue to rotate the spacer
upward until the spacer is free, being carefully not to drop the spacer when it becomes
free. Remove the shaft from the switch. If the shaft is not exposed after several revolution
of the spacer, insert a small slot screwdriver in the hole in the right switch and continue
rotating the spacer upward while the screw driver prevents the shaft from rotating.
Adding handle ties. If additional ties are needed to accommodate additional 240-volt
or multi-wire circuits, they can be added to adjacent pairs of switches.

Warning: Transfer switch circuits with 20 amp breakers must be installed on only
those branch circuits with 20 amp branch circuit breakers. Transfer switch circuits
with 15 amp breakers can be installed on 15 or 20 amp branch circuits. Do not
install any transfer switch circuit on branch circuits greater than 20 amps,
except in position A and B which must be 30 amps.

Installing 240-volt circuit(s)

1. Locate the two red and two black wires from any adjacent circuit positions.
2. Turn off the double-pole breaker in the load center.
3. Loosen the screws that secure each wire to each circuit breaker. Disconnect the wires
from the circuit breakers.
4. Feed the two red wires in Step 1 to the double-pole circuit breaker.
5. Cut the red wires to a convenient length. Strip 5/8" from the end of each wire. Connect
the two red wires to the double-pole circuit breaker.
6. Cut the black wires to a length convenient for aligning with wires removed from the
circuit breaker. Strip 5/8" from the end of each wire.
7. Insert one wire removed from the circuit breaker and one black wire into a yellow wire
connector. Twist to tighten and push the wires back into the wiring compartment of the
load center. Do the same for the other wire removed from the circuit breaker and the
other black wire from the transfer switch.
8. Be sure that a handle tie is connected between the two circuit selector switches.
Repeat steps 1-8 for the other double-pole circuits.
30-Ampere Circuits. Only circuits A and B may be used for 30-amp. circuits. Follow the
above wiring instructions for installing 240-volt circuits. If 30-amp. single-pole circuits are
being used, refer to the previous section regarding installation of 120-volt cirucits.
For models with C or D suffix, or to hard wire any cord-connected model, continue to the
next section entitled "Hard-wire Installation" to complete the installation.
For models with a A or B suffix skip to "Inlet Installation for Indoor Models Used Outdoors"
on page 7.

6
Hard-wire Installation
"Hard-wire" installation to a power inlet box located remotely from the transfer switch (Figure
5) requires additional steps to complete the installation. The wire connections to the wires
from power inlet box are made in the circuit breaker compartment of the transfer switch.
Access the circuit breaker compartment by removing the two screws located on the sides of
the lower circuit breaker
compartment cover. Replace when
installation is complete.

From the transfer switch, connect:

the black wire lead to the
power inlet X or Y terminal

the white wire lead to the
power inlet neutral W terminal

the red wire lead to the power
inlet X or Y terminal

the green wire lead to the
power inlet ground G terminal.

Inlet Installation (For indoor models installed outdoors)

Suffix A and B models have a power inlet included. The inlet can be installed on the unit
by removing the circuit breaker compartment cover (described in the proceeding section)
and the power inlet filler plate, installing the inlet with the enclosed screws onto the wiring
compartment cover, and connecting the wire leads to the inlet as described in the
instructions included with the inlet. Make sure the unit is installed in a dry location.

Completing the Installation

When you have wired all the load circuits in the transfer switch, only the white neutral wire
and the green ground wire remain.
1. Insert the white neutral wire into an unused opening in the neutral bar in the load
center and tighten the screw (Figure 4).
2. Insert the green ground wire into an unused opening in the ground bar, if existing, and
tighten the screw. If no ground bar exists, insert the green wire into an unused hole in
the neutral bar and tighten the screw.
3. Replace the cover to the load center.
4 Fill in the chart on the transfer switch to identify your emergency circuits and
corresponding circuit numbers in the load center.
5 Return all load center branch circuit and main breakers to the "ON" position.
6 Move all circuit selector switches on the transfer switch to the
"LINE" position.
Installation is now complete.

7
 Operating Instructions
Using your Reliance Transfer Switch and Your Portable Generator

Warning: Do not operate a generator in an enclosed area.

Do not operate a generator where the exhaust
fumes can accumulate in an enclosed area.
You want your generator to be ready when you need it. Therefore, it is important to
perform the following steps at least once a month to keep the generator in peak running
condition.
• Start and run your generator under load regularly.
• Keep the fuel tank filled with fresh fuel.
It is not necessary to turn off any circuits in the load center when supplying generator
power with the transfer switch, even when the utility power is operating normally. The
double-throw action of these switches prevents feeding generator power to the utility and,
conversely, prevents feeding utility power to the generator.

Transferring from Utility Power to Generator Power

1. Plug the female connector of the generator power cord into the power inlet box or the
power inlet on the transfer switch. All circuit selector switches on the transfer switch
should be in the LINE or OFF position.
2. Insert the male plug of the power cord into the outlet on the generator.
3. Start the generator outdoors. Follow the procedures described in the generator
owner's manual furnished by the manufacturer of the generator.
4. Select the circuits to be powered by the generator by moving the corresponding
switches on the transfer switch to the GEN position. Use only necessary household
items when under generator power.
5. Alternate use of larger loads (furnace motors, well pumps, refrigerators, etc.) to
balance the load. See "Balancing the load" on page 4. Do not exceed the maximum
wattage of the transfer switch.
6. A 15 amp. transfer switch circuit breaker will limit that circuit to a maximum of 15 amps
when in the GEN position. If you have moved a circuit selector switch on such a 15-
amp circuit to the GEN position that controls a branch circuit that normally draws more
than 15 amps, it may be necessary to turn off some of the appliances on that circuit to
avoid exceeding the 15-amp load for that circuit.
7. Determine circuit wattage by using the wattmeters on the transfer switch, or from the
nameplate on each appliance or motor. Very small loads may not be sufficient to
cause a meter to register.
8. Models with suffix -B and -D do not have watt meters. Determine wattage from the
nameplate on each appliance or motor.
9. Make a note of any excessive loads. These loads must be turned off during
generator operation.

8
Transferring from Generator Power to Utility Power
1. Return all circuit selector switches to the LINE position.
2. Follow the procedures in the generator owner's manual to turn off the generator.
3. Unplug the power cord.

Notes on Models Without Watt Meters

Check the nameplate on each appliance or motor and note the load for each. Determine
the total running wattage of your generator. During an emergency situation with the
generator running, the circuit selector switches should be in the OFF or LINE position
when a particular load is not needed. Failure to limit the total load to the total running
wattage may cause the generator to stall or create an undervoltage condition that could
damage an appliance motor.

Specifications and Parts List

Model # A304 A306 A506 A308 A310 A510
Max. Watts 7500 7500 12500 7500 7500 12500
Max. single-pole circuits 4 6 6 8 10 10
Max. double-pole and multi-wire 2 3 3 4 5 5
circuits
# of handle ties provided 1 1 1 2 2 2
Max. combined loads @ 125 60A 60A 100A 60A 60A 100A
VAC
Max. combined loads 30A 30A 50A 30A 30A 50A
@250VAC
Max. load/circuit from generator 2-30A 2-30A 2-30A 2-30A 2-30A 2-30A
2-20A 4-20A 4-20A 6-20A 8-20A 8-20A
Max. load/circuit from load 2-30A 2-30A 2-30A 2-30A 2-30A 2-30A
center 2-20A 4-20A 4-20A 6-20A 8-20A 8-20A
Power inlet, NEMA* L14-30 L14-30 CS6375 L14-30 L14-30 CS6375
configuration non-NEMA non-NEMA

Minimum cord gauge AWG 10 AWG 10 AWG 6 AWG10 AWG 10 AWG 6

No. of conductors (wires) 4 4 4 4 4 4

Conduit length 18” 18” 18” 18’ 18” 18”

Conduit, trade-size diameter ¾” ¾” ¾” 1” 1” 1”

Optional Power Inlet Catalog # PB30 PB30 PB50 PB30 PB30 PB50

*National Electrical
Manufacturer's Association

9
Transfer Switch Parts List
3

Description Part# Description Part#

Circuit breaker, 15 A S.P. RCB115 Power inlet, 20 A L1420F
Circuit breaker, 20 A S.P. RCB120 Power inlet, 30 A L1430F
Circuit breaker, 20 A D.P. RCB220 Power Inlet, 50 A LL550F
Circuit breaker, 30 A D.P. RCB230 Handle tie A7830
Wattmeter, 20 / 30 A 7236-CP Power Inlet Filler Panel 6271-CP
Wattmeter, 50 / 60 A 7239-CP Switch, 30A SPDT 7801-CP
Current Transformer (C.T.) 7222-CP

Warranty
Each Reliance transfer switch or accessory is
guaranteed against mechanical or electrical failure due
to manufacturing defects for a period of 60 months
following shipment from the factory. The
manufacturer's responsibility during this warranty
period is limited to repair or replacement, free of
charge, of products proving defective under normal use
or service when returned to the factory, transportation
charges prepaid. Guarantee is void on products that
have been subjected to improper installation, misuse,
alteration, abuse or unauthorized repair. The
manufacturer makes no warranty with respect to the
fitness of any goods for a user's particular application
and assumes no responsibility for proper selection and
installation of its products. This warranty is in lieu of all
other warranties, expressed or implied, and limits the
manufacturer's liability for damages to the cost of the
product. This warranty gives you specific legal rights,
and you may have other rights, which vary from state
to state.

Reliance Controls Corporation / 2001 Young Court / Racine, Wl 53404

Phone: (800) 634-6155 Fax: (262) 634-6436

© Copyright 2000 Reliance 10/10/14

10