Test Report – Proof of Service: INSTALLATION HDH TNC620 / TNC640
Customer SOTECH S.R.L. Week 08 / 2019
Contact TOMMASO ABBADIR
Section Telephone
E- Mail
Address/ Street VIA DEL LAVORO , 20 Contact
Postal Code 30030 Telefon
City PIANIGA(VE) E- Mail
Machine DMG Control TNC 640
Machine Type DMU 50 NC Version
Machine No. 14505767844 PLC Version
Year of Make 2018 NCK Version
Customer Inv. Nr. IP- Address
m&h System Serial-Nr. Switch- / DIP-Switch setting Chnannel
Touch Probe 40.02-SK40-120 - - - - # 8082
Tool Setter #
Receiver 91.42 # 1796
Activities
Wiring via
Receiver installed at
Installation
Tool Setter installed at
Cycle Tree Cycle Version
Measuring Speed 250 mm/min Probe-/ Tool Setter activation via:
Commissioning
Positioning Speed 2500 mm/min Stylus alignet at: 5µ
Machine Parameter Settings
Touch Probe (TS) Tool Setter (TT)
Touch Table Old Value New Value Recommendation CfgTT Old Value New Value Recommendation
NO Value type Value
TYPE Value port X112 o. X113
CAL_OF1 Value stylusType RoundStylus
CAL_OF2 Value spindleOrientMode +19 / -1
CAL_ANG Value probingRoutine Value
F 250 probingDirRadial Value
FMAX 2500 offsetToolAxis 5
DIST 20 rapidFeed 2000
SET_UP 10 probingFeed 100
F_PREPOS FMAX_PROBE probingFeedCalc Variable Tol.
TRACK ON spindleSpeedCalc Automatic
maxPeriphSpeedMeas 60
System\ProbeSettings\ maxSpeed 0 / 1000
Cfg Probes measureTolerance1 0.005
activeTT Value measureTolerance2 0.01
maxTouchFeed 2500 stopOnCheck TRUE
activeEnDatSE FALSE stopOnMeasurement TRUE
adaptToolTable AdaptOnBoth
Cfg TS radioTransmission FALSE with IR
Spindle Name i.e.: S or S1 CfgTTRoundStylus
mStrobeUturn +19 / -1 centerPos [0] (X) Value
mStrobePos +19 / -1 centerPos [1] (Y) Value
centerPos [2] (Z) Value
Other Machine Data Changed stylusAxis Value
stylusDimension 13 / 37
safetyDistToolAx 10
safetyDistStylus 10
FIN1919-WK08-Sotech.docx Page 1 of 2
. .
Tel +49(0)7529 / 9733-32 Fax +49 (0)7529 / 9733-7 [email protected]
Test Report – Proof of Service: INSTALLATION HDH TNC620 / TNC640
Training (if required)
System Training Measuring Cycles Service
Participants: Participants:
ANDREA VIANELLO
Handling Man. Measuring Cycles
Alignment Half-autom. Meas. Cycles
Accesories (Toolbox) Auto. Meas. Cycles
Calibration Practical Exercises Workpiece- Tool measurement
Collision control
n. OK OK
1. Is the machine moving in a measuring cycle without a ready signal? Yes No
2. Has ready or probe status signal influence in manual mode at the feed motion or revolution of the machine? Yes No
If yes, effect
3. Has ready or probe status signal influence in automatic mode at the feed motion or revolution of the machine? Yes No
If yes, effect
4. Is the machine still moving in a cycle after removing the battery? Yes No
5. Is spindel feed possible with probe in spindle? (i.e. S100, M3) Yes No
6. Influence by other machines / probes? Yes No
7. Function test of low battery and ready signal? No Yes
8. Move all axes to end positions. Check for collision and reception? No Yes
9. Change in automatically the probe and start a measuring cycle? No Yes
Collision control active by (i.e. option parameter MP4310 / M-function / etc.)
Data Backup
Control Tool Setter / Laser
Before Installation MH-PTS-INI.mh
After Installation MH-LTS-INI.mh
Account / Billing
Account / Billing according to order
Account / Billing
Travel distance 720 km 1. € per driven km
Hourly rate 8 hours 70.- € per hour
Other
Remarks
EFFETTUATA INSTALLAZIONE RICEVITORE 91.42,TASTATORE 40.02
SETTATI PARAMETRI PER L‘UTILIZZO DEL TOOLSTTER GIA’ IN POSSESSO DEL CLIENTE
EFFETTUATO RUNOUT DELLO STILO DEL TASTATORE ED ESEGUITE LE CALIBRAZIONI IN Z E IN XY
ALLINEATO E TROVATO IL CENTRO DEL PIATTELLO DEL TOOLSETTER ED ESEGUITA LA CALIBRAZIONE
EFFETTUATE VARIE PROVE ED ESERCIZI DI MISURAZIONE E CENTRAGGIO DEL PEZZO E MISURAZIONE UTENSILE
IL TUTTO RISULTA FUNZIONANTE
To Do
Documents to send Provide an offer Other
27 / 02 / 2019
Date / signed by m&h - Technician
TOMMASO ABBADIR FABIO INCAVIGLIA
FIN1919-WK08-Sotech.docx Page 2 of 2
. .
Tel +49(0)7529 / 9733-32 Fax +49 (0)7529 / 9733-7 [email protected]
