University of Gondar

Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
Choose Correct or the Best Alternative in the Following Problem
1) While designing a constant-k low pass filter (T-section) shown below, what would be the
value of capacitor if L/2 = 20mH, R0 = 500 Ω and fc = 5 kHz?

A) 0.0635 μF
B) 0.10 μF
C) 0.1273 μF
D) 0.20 μF
2) For a constant k type LPF with T- section, with the cut-off frequency of about 4 kHz,
what will be the value of stop-band attenuation at 8 kHz?

A 10.03 dB
B) 22.87 dB
C) 35.04 dB
D) 50.02 dB
3) In the circuit, the driving point impedance is (s + 5) / (s2 + 5s + 1). Hence, the driving point
admittance of the circuit is ___.
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
A (s + 5)
B) (s2 + 5s + 1)
C) (s + 5) x (s2 + 5s + 1)
D) (s2 + 5s + 1) / (s + 5)
4) What would be the characteristic impedance of a T-section for symmetrical network shown
below?

A) 300.15 ohm
B) 529.15 ohm
C) 715.15 ohm
D) 900.15 ohm

5) Consider the symmetrical T-network shown below. What will be the value of propagation
constant, if characteristic impedance is estimated to be Z0 = 850.64 ohm?

A) 0.2824 neper
B) 0.1412 neper
C) 0.0706 neper
D) 0.0353 neper
6) What do the high pass filters generally comprise of?
A. Capacitive series arm
B. Capacitive shunt arm
C. Inductive series arm
D. Inductive shunt arm
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
A) A & D

B) A & C

C) B & C

D) B & D

7) For the design of prototype high pass filter T section, what would be the value of inductor if
design impedance and cut-off frequency are 600 ohm and 1500 Hz respectively?

A) 19.89 mH

B) 31.83 mH

C) 40.13 mH

D) 51.83 mH

8) Which value of ‘m’ is selected in a composite filter, while connecting the terminating sections
in order to acquire proper impedance matching and constant characteristic impedance throughout
the pass band?

A) 0.3

B) 0.6

C) 0.9

D) 0.12
9) It is possible to overcome the drawback of m-derived filter by connecting number of sections
in addition to prototype & m-derived sections with terminating ___
A) One-fourth sections
B) Half sections
C) Square of three-fourth sections
D) Full sections
10) Which is the correct condition of symmetry observed in z-parameters?
A) Z11 = z22
B) Z11 = z12
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
C) z12 = z22
D)z12 = z21
11) Which among the following represents the precise condition of reciprocity for transmission
parameters?
A) AB – CD = 1
B) AD – BC = 1
C) AC – BD = 1
D) None
12) If z-parameters are z11 = 40, z22 = 50 and z12 = z21 = 20, what would be the value of y22 in the
matrix form of y-parameters given below?

A) 4 / 160
B) 5 / 160
C) 10 / 160
D) 15 / 150
13) _______ is expressed as the inverse of impedance.
A) Resistance
B) Admittance
C) Reactance
D) Capacitance
14) The following property relates to LC impedance or admittance functions:
A) The poles and zeros are simple and lie on the jω -axis.
B) There must be either a zero or a pole at origin and infinity.
C) The highest (or lowest) powers of numerator or denominator differ by unity.
D) All of the above.
15) An L-C impedance or admittance function:
A) Has simple poles and zeros in the left half of the s-plane.
B) Has no zero or pole at the origin or infinity.
C) Is an odd rational function.
D) Has all poles on the negative real axis of the s-plane.
16) The admittance and impedance of the following kind of network have the same properties:
A) LC
B) RL
C) RC
D) RLC
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023

17) The minimum amount of hardware required to make a low pass filter is
A) a resistance, a capacitance and an op-amp.
B) a resistance, an inductance and an op-amp.
C) a resistance and a capacitance.
D) a resistance, a capacitance and an inductance.
18) For the design of low-pass prototype filter Fig.2 of with load resistance RL = 1 Ω and angular
frequency w = 1 rad/s the values of L and C would be

Figure 2
A) 1 H and I F
B) 1 H and 2 F
C) 2 H and I F
D) 2 H and 2 F
19) The circuit shown in Fig. 3 is

Figure 3
A) Cauer I form
B) Foster I form
C) Cauer II form
D) Foster II form
20) ABCD Parameters are used in analysis of……..
A) Short circuit
B) Electronic circuit
C) Open circuit
D) Transmission line
𝑠(𝑠+3)
21) The function Z(s) = represent a
(𝑠+2)(𝑠+4)

A) R-L function
B) L-C function
C) R-C function
D) R-L-C network
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
22) The circuit of figure is generally employed as a

A) Low- pass filter

B) High -pass filter
C) band- pass filter
D) Stop band filter
23) The deriving point admittance of the network shown below is

𝑠4+3𝑠2+1
𝐴)
𝑠(𝑠2+1)

𝑠2+1
𝐵) s+
𝑠(𝑠2+2)

𝑠3+2𝑠2
𝐶)
𝑠4+3𝑠2+1
𝑠3+2𝑠2+3
𝐷)
𝑠2+2

24) Cauer and Foster forms of realization are used only for
a) Deriving point reactance function
b) Transfer reactance function
c) Deriving point impedance function
d) Transfer impedance function
𝑠5+5𝑠3+3𝑠
25) The deriving point impedance function Z(s) =
𝑠4+3𝑠2+1

A) R-L function
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
B) L-C function
C) R-C function
D) R-L-C network
26) In two port networks, the total number of terminals is:
A) 1
B) 2
C) 3
D) 4
27) Transmission parameter is also known as:
A) Z-parameter
B) Y-parameter
C) ABCD parameter
D) h-parameter
28) In ABCD-parameters, choose the correct one
A) V1& V2 in terms of I1& I2
B) I1& I2 in terms of V1& V2
C) V1& I2 in terms of V2& I1
D) V1& I1 in terms of V2& I2
𝑠2+𝑋𝑠
29) What is the value of X in 𝑠2+5𝑠+4
so that it is deriving point impedance?

A) 0
B) 1
C) 2
D) 4
(s2+1)(s2+3)
30) The cauer form-1 synthesis for the L-C d.p impedance is
s(s2+2)
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023

3(𝑠+2)(𝑠+4)
31) The foster form-1 sythesis for F(s) is
𝑠(𝑠+3)

32)Which of the following deriving point impedance function?

a(𝐬𝟐+𝟏)(𝐬𝟐+𝟖)
𝐬(𝐬𝟐+𝟒)
b) 𝟐
(𝐬𝟐+𝟐)(𝐬𝟐+𝟒)
c) 𝟓
𝐬(𝐬𝟐+𝟒)
d) (𝐬𝟐+𝟒𝐬+𝟑)
𝐬𝟐+𝟔𝐬+𝟖)

5s(s2+8)
33)The fraction (s2+1)(s2+4)
is not d.p ipmedance function because

A) it is not even to odd ratio fuction

B)poles and zeros are not simple
C)poles and zeros are does interlate on jω axis
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
D) there is no poles or zeros at infinity
34) The pass band of a constant k filter with Z1 and Z2 as series and shunt arm impedances is
given by
𝑧1
A) -1< <0
4𝑍2
𝑧1
B) -2< <-1
4𝑍2
𝑧1
C) 1< <0
4𝑍2
𝑧1
D) 0< <1
4𝑍2

35) For an m-derived high pass filter

a) True b) false
36) Consider the following statements associated with two port networks
1. Z12 = Z21
2. Y12 = Y21
3. h12 = h21
4. AD - BC = 1

Which one of the statement given above are correct?

A) 1, 2, 3
B) 2, 3, 4
C) 1, 3, 4
D) 1, 2, 4
37) The impedance parameter z21 is
A) Transfer impedance at port 1 with port 2 open circuited
B) Transfer impedance at port 1 with port 2 short circuited
C) Transfer impedance at port 2 with port 1 open circuited
D) Transfer impedance at port 2 with port 1 short circuited
38) An m derived LPF has fc = 1000 Hz, f∞ = 1250 Hz and m = 0.6. If m is increased, then
A) Both fc and f∞ will increase
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
B) Both fc and f∞ will decrease
C) Fc will remain constant but f∞ will decrease
D) Fc will remain constant but f∞ will increase
39) For an RC admittance function
A) All poles and zeros are simple
B) All poles and zeros are simple and lie on negative real axis
C) All poles and zeros lie on imaginary axis
D) All poles and zeros lie on positive real axis
40) In the two ports network shown in the figure, Z12 and Z21 are, respectively

A) re and βr0
B) 0 and - βr0
C) 0 and βr0
D) re and - βr0
41) Consider the following expression for the driving point impedance

1. It represent on LC circuit

2. It represent on RLC circuit

3. It has poles lying on the jω axis

4. It has a pole at infinite frequency and a zero at zero frequency.

Which one the statement given above are correct?

A) 2 and 4
B) 1 and 3
C) 1 and 4
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
D) 2 and 3
42) If Y(s) = 1 + s, the network has
A) 1 Ω resistor and 1 F capacitor in series
B) 1 Ω resistor and 1 F capacitor in parallel
C) 1 Ω resistor and 1 H inductor in series
D) 1 Ω resistor and 1 H inductor in parallel
43) If two networks are connected in series of individual Z parameter as Za and Zb then
equivalent Z is
A) [Z] = [Za] + [Zb]
B) [Z] = [Za] [Zb]
C) [Z] = [Za]/[Zb]
D) [Z] = [Za] - [Zb]
44The series element for a prototype high pass filter is
A) Resistive
B) Inductive
C) Capacitive
D) Combination of L and C
45) In open circuit impedance parameters, the independent variables are
A) I1 and I2
B) V1 and V2
C) V1 and I1
D) V2 and I2
46) If two networks are connected in parallel then equivalent y parameter of both is
A) [Y] = [ya] [yb]
B) [Y] = [ya] + [yb]
C) [Y] = [ya]/[yb]
D) None
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
47) In low pass filter of figure R0 = 1 Ω and cut off frequency is 1 rad/sec. The values of L and C
are

A) 1 H and 2 F
B) 1 H and 1 F
C) 2 H and 1 F
D) 1 H and 2 F
48) Pick the correct statement with respect to following figure.

A) Both the circuit are not identical filter Ckts

B) Identical filter circuit at all frequencies
C) Identical filter circuit at low frequency
D) Identical filter circuit at high frequency
49) In figure, . The values of C and R are

A).

B)
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
C)

50) Assertion (A): is not an LC function.

Reason (R): The highest powers of numerator and denominator do not differ by 1.
A) Both A and R are true and R is correct explanation of A
B) Both A and R are true and R is not the correct explanation of A
C) A is true but R is false
D) A is false but R is true
51) For the network of figure, [z] matrix is

A)

B)

C)

D)
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
52) Which of the following is correct? The circuit shown in the figure.

1. is reciprocal but not symmetrical

2. is not reciprocal but symmetrical

3. both reciprocal and symmetrical

4. neither reciprocal nor symmetrical

A) 1, 2 and 3
B) 2, 3 and 4
C) 1, 3 and 4
D) 1, 2 and 4
53) A network is said to be two port network if there is
1. no independent source in the network

2. no dependent source in the network

3. non-linear component in the circuit

4. no external connection exist between I/P and 0/P

A) 1, 2, 3
B) 3, 4, 2
C) 1, 3, 4
D) 4, 3, 1, 2
54) The first and the last critical frequencies (singularities) of a driving point impedance function
of a passive network having two kind of elements, are a pole and a zero respectively. The above
property will be satisfied by
A) RL network only
B) RC network only
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023
C) LC network only
D) RC as well as RL network
55) For an RC driving point impedance function, the poles and zeros
A) Should alternate on real axis
B) Should alternate only on negative real axis
C) Should alternate on imaginary axis
D) None of the above
56) In h parameter representation, the independent variables are
A) I1 and V2
B) I2 and V1
C) V1 and V2
D) I1 and I2
57Two independence parameters Z11 and Z12 of the two-port network in the figure are

A) Z11 = 2.75 Ω and Z12 = 0.25 Ω

B) Z11 = 3 Ω and Z12 = 0.5 Ω
C) Z11 = 3 Ω and Z12 = 0.25 Ω
D) Z11 = 2.25 Ω and Z12 = 0.5 Ω
58) The function is an

A) LC function
B) RC function
C) RL function
D) LC or RC function
 University of Gondar
Institute of Technology
Department of Electrical Engineering
Network Analysis and Synthesis Model Exit Exam
By Admasu y Academic Year 2022/2023