Basic Solid Edge ST Tutorial

Introduction
This tutorial introduces you to the Solid Edge Part environment and various feature-based modeling techniques, such as: 1. 2. 3. 4. Drawing and dimensioning profiles Using geometric relationships Constructing and editing features Ensuring model symmetry and stability

The tutorial does not demonstrate everything Solid Edge can do. Its purpose is to show you how powerful and intuitive the modeling environment is, and to get you started so you can learn more on your own. During this exercise, you will construct the model shown in the illustration above.

Select Units and Type of Operation

The first tasks are to change the units to millimeters, and type of operation available. The standard units used with the default installation of Solid Edge are ISO (millimeters), but some installations may have used ANSI (inches) instead. If so, you need to change to millimeters for this tutorial. Once you have started execution of the Solid Edge program in Windows, you will see a screen similar to the one shown below. If the options in Create are the ones shown, you will need to make two changes before you can start the

tutorial. If the option Traditional ISO Part is available, select it and go the next part of this tutorial labeled Start the Extrude command.

Otherwise, select the icon in the upper left corner of the screen, which will bring up the following window.

Select the Solid Edge Options at the bottom of the screen which will bring up the following window.

Within this window, select User Profile, then use the down arrow next to User type and select Traditional and Synchronous. Select OK. This will change the start up screen to be the following, which will allow you to select Traditional part construction.

The next step is to change the units to ISO. Select the icon in the upper left corner and then select New as shown.

This will bring up the following window.

Within this window select More and then iso part.par and then OK. Now you can start the construction of the model. 4

Select the Extrude command

On the command menu, along the top of the Solid Edge application, choose Home tab>Solids group, and select Extrude to start the Extrude command. An Extrude command bar is displayed on the left side of the application:

and PromptBar is displayed along the bottom of the application:

The Extrude command, like all the feature-creation commands in Solid Edge, uses a command bar to guide you through the feature construction steps without limiting you to a strict linear workflowyou can move back and forth among the steps as you work. The prompt in PromptBar displays instructions for completing the current task. The reference plane option that is displayed in command bar on your computer may be different than the illustration. In the next step, you will set the proper option.

Prepare to construct the base feature

The first step in drawing any new part is constructing a base feature. The base feature defines the basic part shape that you modify to construct the finished part. You will use the Protrusion command to extrude a 2-D profile along a straight line, creating a 3-D feature as show below.

In the next step, you will select a reference plane on which you will draw the profile. For this feature, you will draw the profile on a reference plane that is coincident to one of the three base reference planes. On the Protrusion command bar, in the Create-From Options list, select the Coincident Plane option.

Select a profile plane

Move the cursor to the edge of the horizontal reference plane shown in the illustration. Click when the plane is highlighted.

What is the profile plane for? The profile plane is a 2-D surface you draw profiles on. When you select a profile plane, Solid Edge reorients the profile plane parallel to the computer screen so you can draw the profile easily. At the same time, the toolbars and menus change. Buttons for constructing features are hidden, and buttons for drawing and modifying 2-D wireframe elements are displayed instead. When you finish drawing the profile in the true view, Solid Edge reorients the profile plane back to where it was, with the profile on it, and changes the menus and toolbars back to the 3-D commands.

Draw a rectangle
On the Home tab>Draw group, click the Rectangle button.

Position the cursor at Point (1), as shown in the illustration, and click. Move the cursor towards point (2) and notice that the Rectangle ribbon bar show the current Width value. updates to

Also notice that when the cursor position is exactly horizontal to point (1), the value in the Angle box locks at 0.00 degrees. Move the cursor to the right until the Width value is approximately 130 mm, and the Angle value is exactly 0.00 degrees. Click to define Point (2). Move the cursor down until the Height value is approximately 90 mm. Click to define Point (3).

A rectangle, consisting of two horizontal and two vertical lines, which are end-point connected is displayed.

Observe the rectangle

Notice that symbols representing geometric relationships are displayed on the rectangle. Geometric relationships control how the profile geometry reacts to modifications you make. These relationships were automatically applied based on the cursor position and the current IntelliSketch settings. You will learn more about this in the next few steps. The symbols on the midpoint of the lines represent horizontal and vertical relationships. The symbols on the endpoints of the lines represent end-point connect relationships. When you modify the rectangle profile later, the lines will remain endpoint-connected, and horizontal and vertical.

Learn more about IntelliSketch

On the Tools tab>Assistants group, click IntelliSketch. The IntelliSketch dialog box is displayed.

Take a few moments to review the options on the Relationships tab on IntelliSketch. The Relationships tab defines which relationships are recognized by IntelliSketch as you draw. Your settings should match the illustration. If not, change your settings so that they match the illustration. Notice that the Endpoint and Horizontal or Vertical options are set. These options were used to automatically apply the relationships to the rectangle you just drew. On the IntelliSketch dialog box, click OK.

Delete a line
To illustrate how you delete and add elements to a profile, you will now delete one of the lines, and then draw a replacement line. The Select Tool lets you select elements so they can be edited, copied, and deleted. On the Home tab>Select group, click the Select button. Move the cursor over the lines in the profile. Notice that the lines highlight as the cursor passes over them. Position the cursor over the line shown in the illustration below, then click to select it.

Notice that: 1. The line color changes to the Select color. 2. The Line ribbon bar is displayed, showing the length and angle of the line. Now press the DELETE keythe line is deleted from the profile. Note: The cursor must be positioned in the Profile window when you press the DELETE key. Notice that the line, the horizontal relationship and the endpoint connect relationships were all deleted.

Draw a new line

Move the cursor to the endpoint of the line shown in the top illustration, and when the endpoint relationship indicator displays adjacent to the cursor, click. Move the cursor to the endpoint of the line shown in the bottom illustration, and when the endpoint relationship indicator displays adjacent to the cursor, click.

10

When you have finished drawing the line, click the right mouse button to restart the Line command.

Observe the results

Take a few moments to observe the line you drew. The new line should have end-point connect relationships at both ends, and a horizontal relationship near its midpoint. If your profile does not match the illustration, use the Select tool to delete the line and the Line command to draw another line.

Dimension the rectangle width

On the Home tab>Dimension group, click the SmartDimension button. Position the cursor over the horizontal line on the rectangle, as shown in the following illustration. When the line highlights, click to select it.

11

Move the cursor above the profile as shown in the illustration below, then click to define the dimension location.

Notice that the exact dimension value is displayed on the Dimension ribbon bar the graphic window.

and in

On the Dimension ribbon bar, type 130, then press the ENTER key on the keyboard. Tip: When typing values in a ribbon bar box, you do not have to enter the unit type, such as mm or degrees. Notice that the display value and the profile width update. The dimension you placed is a driving dimension. Driving dimensions control, or drive, the elements on which they are placed.

Dimension the rectangle height

The SmartDimension command is still active. Position the cursor over the vertical line on the rectangle, as shown in the following illustration. When the line highlights, click to select it.

12

Move the cursor to the left, then click to position the dimension.

Type 90, then press the ENTER key on the keyboard, and notice that the display value and the profile height update.

Taking advantage of part symmetry

The current dimensions and geometric relationships fully define the size and shape of the profile, but the profile is still free to move around on the profile plane. Because the part you are constructing will have symmetric features, you can take advantage of the part symmetry if you ensure that the profile stays symmetrically oriented to the base reference planes (A) and (B) as shown below. Tip: You can use the base reference planes to take advantage of part symmetry and make your models easier to build and edit. This also helps build stability and predictability into your models.

13

In the next few steps, you will use horizontal and vertical relationships to symmetrically position the rectangular profile.

Using relationships to ensure symmetry

In addition to specifying that a line remains horizontal or vertical, you can also use a horizontal/vertical relationship to specify that one element remains horizontally or vertically aligned with respect to another element. For this part, you will use a horizontal/vertical relationship to specify that the midpoint of the vertical line (A) stays horizontally aligned with one of the base reference planes. You will then use this technique again to specify that the midpoint of the horizontal line (B) stays vertically aligned with one of the base reference planes.

This ensures that the rectangular profile, regardless of its size, will stay symmetrically oriented to the base reference planes. This technique is a powerful tool that can be used in many situations. 14

Tip: You can use a horizontal/vertical relationship to specify that two elements remain horizontally or vertically aligned with respect to each other.

Apply a horizontal relationship

On the Home tab>Relate group, click the Horizontal/Vertical button. Position the cursor as shown in the following illustration, and when the midpoint relationship indicator displays adjacent to the cursor, click.

Position the cursor where the reference planes intersect, as shown below, and when the midpoint relationship indicator displays, click. It does not matter which reference plane highlights. The profile position updates.

Apply a vertical relationship

The Horizontal/Vertical command should still be active.

15

Position the cursor as shown in the following illustration, and when the midpoint relationship indicator displays, click.

Position the cursor where the reference planes intersect, and when the midpoint relationship indicator displays, click. The profile position updates.

Edit the dimensions

The size, shape and position of the rectangular profile is now fully defined, or fully constrained. For this profile, if you edit either of the dimensions, it will also stay symmetrically oriented about the reference planes. On the Home tab>Select group, click the Select button. Position the cursor over the 130 millimeter dimension, and click to select it. Notice that the Dimension ribbon bar is displayed.

16

On the Dimension ribbon bar, type 100, then press the ENTER key.

If you would like to experiment with other values, feel free to do so.

Finish the profile and close the profile view

The Select tool command should still be active. If required, edit the dimensions so that they match the illustration.

17

On the Home tab>Close group, select the Close Sketch button. Clicking Close Sketch closes the profile view and returns you to the 3-D part view. The Extrude command bar shows that the next step is the Extent Step, i.e. projecting the 2-D profile to form a 3-D solid.

Define the feature extent

Position the cursor below the profile you just drew, and notice that the feature is drawn dynamically as you move the cursor. Also notice that the Distance box on the Extrude command bar dynamically updates to show the extent of the feature. 18

On the Extrude command bar , type 40 in the Distance box for the extent of the base feature, then press the ENTER key.

Position the cursor below the profile, as shown above, and click to finish defining the extent. On the Protrusion SmartStep ribbon bar, click the Finish button to end the Protrusion command. Notice that when you clicked the Finish button, that the profile elements, including the dimensions and relationships are automatically hidden for you. You have completed the base feature.

Fit the view

Commands for adjusting the contents of the graphics window are located at the bottomright side of the Solid Edge application window.

19

Choose Fit on the fit the contents of the view to the graphics window.

Save the part

Select the Save As option using the icon in the top-left corner of the screen and save the part as Tutorial.par.

20

Notice the Protrusion 1 entry in Feature PathFinder

On the bottom-left side of the Solid Edge application, click the Feature PathFinder tab. Notice that a Protrusion 1 entry has been added to the Feature PathFinder tab. You can use the Feature Pathfinder tab to help you evaluate and edit the models you create in Solid Edge.

Later you will use Feature PathFinder to select and edit a feature.

Round the edges

You will use the Round command to round five edges of the part, as shown in the illustration.

21

On the Home tab>Solids group, select the Round button . On the Round command bar , set the Select option to Edge/Corner. With this option, the command lets you select edges and corners to be rounded.

On the Round command bar, in the Radius box, type 18, and then press the Enter key.

Select an edge to round

Move the cursor slowly over the model, and notice how the edges of the model highlight. Position the cursor exactly over the vertex shown circled in the illustration below, stop moving the mouse for a moment, and notice that the cursor image changes to indicate that multiple selections are available. Click the right mouse button, and the QuickPick tool is displayed. Move the cursor over the different entries in QuickPick, and notice that different edges of the model highlight. QuickPick allows you to select exactly the edge you want, the first time, without having to reject unwanted edges.

Use QuickPick to highlight the edge shown in the illustration, and then click the left mouse button to select it.

22

Select another edge to round

Position the cursor over the edge at the location shown in the illustration below.

Notice that the edge highlights, but QuickPick is not displayed. No other edges are near the cursor, so the system recognizes that QuickPick is not necessary for you to select the edge you want. Click to select the edge.

Selecting the remaining edges to round

Select the additional edges shown in the illustration.

You will be rounding a total of five edges.

23

Preview and edit the round

On the Round command bar, notice that options are available in the Select Step for changing the radius of the round, deselecting the selected edges, and accepting the current input.

If you selected the correct edges, click the Accept button. If you selected the wrong edges to round, click the Deselect button. This clears all the selected edges so that you can select new edges. On the Round command bar, click the Preview button. The part should resemble the one shown below.

Finish the round

The part should match the illustration below.

When you are satisfied with your results, click Finish on the Round SmartStep ribbon bar.

24

Save the part

On the Quick Access toolbar at the top, click the Save button to save the work you have done so far.

Construct a thin wall

The base feature and rounded edges have defined the general shape of the finished part. The next step is to hollow out the interior, as shown. You will use the Thin Wall command to do this.

On the Home tab>Solids group, click the Thinwall button. On the command bar ENTER key. , in the Common Thickness box, type 8, and press the

Select the first face to leave open

When constructing thin wall features, you typically also specify faces you want to leave open. For this feature, you will select the front and top faces of the part.

25

Position the cursor over the face shown in the illustration below. If the front face shown highlights, click the left mouse button to select it. If a different face highlights, use QuickPick to select the face shown in the illustration.

Tip: If the element you want to select is highlighted, you can bypass QuickPick and select the element directly using the left mouse button.

Select the second face to leave open

Select the top face shown in the illustration.

On the Thin Wall SmartStep ribbon bar, click the Accept button. This tells the system that you are done selecting open faces.

Preview the thin wall feature

On the Thin Wall command bar, click the Preview button.

26

Your part should look like the illustration below.

Finish the thin wall

If the part does not look like the illustration above, you can use the Thin Wall command bar to edit any of the steps you took to create the thin wall. If the thickness of your part looks different than the illustration, click the Common Thickness step on the command bar and make sure that the thickness is set to 8 mm. If the open faces on your part look different than the illustration, click the Open Faces step on the command bar, click the Cancel button to clear the selected faces, and then select the faces again. When you are satisfied with the appearance of your part, click Finish.

27

Save the part

On the Quick Access toolbar, click the Save button to save the work you have done so far.

Construct a protrusion
You will construct a mounting tab on the part, as shown in the illustration. You will use the Extrude command for this.

On the Home tab>Solids group, click the Extrude button.

Create a parallel reference plane

The first step in constructing this feature is selecting a profile plane to draw the shape of the protrusion on. However, there are no reference planes at the location where you will construct the feature. So you need to create a reference plane parallel to an existing face or reference plane. On the command ribbon bar, in the Create-From Options list, click the Parallel Plane option.

28

Select the top reference plane, as shown in the illustration. Remember that you can use QuickPick to help you select the reference plane.

Position the reference plane

On the Protrusion command bar, type 10 in the Distance box, then press the ENTER key. Notice that, by moving the cursor around the top face of the part, you can position the parallel reference plane inside or outside the part. Move the cursor to position the reference plane inside the part, as shown, and then click.

A profile true view is displayed.

29

Evaluate the profile

In the next few steps, you will draw and dimension the profile for the mounting tab, as shown in the illustration below. 1. You will use the Line command to draw the three lines shown. 2. You will use the SmartDimension command to define the 30 mm and 35 mm dimensions. 3. You will use the Distance Between command to define the 36 mm dimension.

Pan the view

On the bottom-right side of the Solid Edge application window, click Pan.

Position the cursor as shown in the illustration above, hold the left mouse button down, then drag the cursor to reposition the geometry to the center of the view, as shown below. Click the right mouse button to exit the Pan command.

30

Start the first line

On the Home tab>Draw group, click the Line button . Position the cursor as shown in the illustration below, and when the point on element relationship indicator displays adjacent to the cursor, click to start the line.

Move the cursor to the right. Notice the following: 1. A line stretches to follow the cursor wherever you move it. 2. When the line is nearly horizontal, a horizontal relationship indicator displayed next to the cursor. is

31

Finish the first line

Move the cursor until: 1. The horizontal relationship indicator is displayed at the cursor. 2. The length displayed on the ribbon bar is approximately 35 mm. 3. The angle on the ribbon bar is zero degrees. When the line is horizontal, and approximately 35 mm long, click to finish the first line.

Draw the second line

By typing the length and angle on the ribbon bar, you can draw lines the exact length and angle you want. If it is not already highlighted in blue, click the Length box on the command bar. The Line command is still active, so the next line will start at the endpoint of the line you just drew. 1. Type 30, and press the ENTER key on the keyboard. Notice that the Length box updates and the Angle box becomes active. 2. Move the cursor around the screen and notice that the line length is locked at 30 mm. 3. Move the cursor down until the vertical relationship indicator is displayed. Notice that the line angle locks at -90 degrees. Click to place the second line. When you know the length or angle you want, you can type exact values in the ribbon bar.

32

Draw the third line

Position the cursor as shown in the illustration above, and when the point on element and horizontal relationship indicators display adjacent to the cursor, click to finish the line. When you have finished drawing the line, click the right mouse button to restart the Line command.

Observe the results

Take a few moments to observe the finished profile.

33

In addition to the horizontal, vertical, and end-point connect relationship you learned about earlier, two point on element relationships (A) and (B) were used for this profile. The point on element relationships connect the horizontal lines you drew to the vertical edge on the part, but the horizontal lines are still free to move up and down. In the next few steps, you will use dimensions to finish defining the size and position of the profile elements.

Dimension the vertical line

On the Home tab>Dimension group, click the SmartDimension button. Position the cursor over the vertical line you just drew, as shown in the illustration below. When the line highlights, click to select it.

Move the cursor to the right, as shown in the following illustration, then click to define the dimension location.

34

If the dimension value is not exactly 30 mm, type 30 on the ribbon bar, then press the ENTER key.

Dimension the horizontal line

The SmartDimension command should still be active. Position the cursor over the horizontal line, as shown in the illustration below. When the line highlights, click to select it.

Move the cursor above the profile, as shown in the following illustration, then click to define the dimension location.

35

The dimension value of this line may not be exactly 35 mm, because you approximated the length of the line when drawing it. If the dimension value is not exactly 35 mm, type 35 on the ribbon bar, then press the ENTER key.

Select the Distance Between command

You have finished defining the size of the profile. One more dimension, as shown, will define location of the profile on the part. On the Home tab>Dimension group, select the Distance Between button.

On the Dimension ribbon bar, ensure that the Horizontal/Vertical option is set.

36

Select the elements to dimension

Position the cursor over the edge of the part, as shown in the following illustration. When the edge highlights, click.

If QuickPick displays, either QuickPick selection is valid. There are two edges available in this situation. Position the cursor over the horizontal line, as shown in the illustration below. When the line highlights, click.

37

Define the dimension orientation

Move the cursor around the screen and notice that the dimension orientation changes to indicate that multiple solutions are available. Position the cursor, as shown in the following illustration, and click to position the dimension.

On the command bar, type 36, then press the ENTER key.

Close the profile view

The profile is now complete, so on the Home tab>Close group, click the Close Sketch button to return to the 3-D model view.

38

Specify the material direction

Choose Fit to fit the contents of the view to the graphics window. On the Extrude command bar, notice that the Side Step is active.

Also notice that in the graphic window, a red arrow is displayed on the profile you just drew. Because this profile is open, you must define the side on which you want to add material. As you move the cursor, the arrow points either outward away from the profile, or inward toward the center of the profile. This arrow determines the side of the profile which material is added to the part Position the cursor so that the arrow points inward, as shown, then click to define the material direction

Project the profile

On the Extrude command bar, type 8 in the Distance box for the extent of the feature, then press the ENTER key. Position the cursor below the profile, as shown below, and click to finish defining the extent.

39

On the Extrude command bar, click the Finish button.

Fit and save the part

Choose Fit to fit the contents of the view to the graphics window. On the Quick Access toolbar, click the Save button to save the work you have done so far.

Round more edges

In the next few steps, you will round the four edges shown in the illustration below. On the Home tab>Solids group, click the Round button.

40

On the Round command bar, set the Select option to Edge/Corner. With this option, you can select edges and corners to be rounded.

On the Round commend bar, in the Radius box, type 8, and then press the Enter key.

Select the edges to round

Select the four edges shown in the illustration below. You may need to use QuickPick to select the edges.

After you select the edges, your model should look like the illustration below.

41

Preview the feature

On the Round command bar, click the Accept button. On the Round command bar, click the Preview button. The part should resemble the illustration.

Finish the round

When you are satisfied with your results, click Finish on the Round command bar.

Save the part

On the Quick Access toolbar, click the Save button to save the work you have done so far.

42

Mirror and copy features

You will now mirror and copy the protrusion and round features you constructed to add identical features to the other side of the part. This is easy because you took advantage of part symmetry when you constructed the base feature. On the Home tab>Solids group, click the Mirror Copy Feature button. On the Mirror Copy Feature command bar, click the Smart button.

Select the features to mirror

In Feature PathFinder, select the Protrusion2 and Round 2 features, as shown. Notice that the features highlight in the graphic window.

43

On the Mirror Copy Feature command bar, click the Accept button. This tells the system that the features you selected are the only ones you want to mirror.

Specify the mirror plane

During the Plane Step of the Mirror Copy Feature command, you specify the plane of symmetry for the new mirrored feature. In the graphic window, select the base reference plane shown.

The features you selected are copied and mirrored to the other side of the part.

Finish the copy

On the Mirror Copy Feature command bar, click the Finish button to complete the feature.

44

Fit and save the part

Choose Fit to fit the contents of the view to the graphics window. Click the Save button to save the work you have done so far. You have completed all the steps for modeling the part. In the next few steps, you learn how to edit the features of the part.

Select a feature to edit

On the Home tab>Select group, click the Select button. You can edit features by selecting them in the graphic window or using the PathFinder tab. On the PathFinder tab, position the cursor over the Protrusion 1 entry, then click.

Notice that the Select command bar is now active. Also notice in the graphic window that the feature changed color.

Explore the editing options

Take a few moments to review the options you have for editing this feature: The Edit Definition button allows you to return to any of the inputs used to create the feature. The Edit Profile button displays the profile true view, and allows you add or delete

45

profile elements, dimensions or geometric relationships. The Dynamic Edit button displays the profile and its dimensions, while leaving the model in its current state. For this edit, you will be editing the value of a dimension, so the Dynamic Edit option is appropriate. On the Select Tool ribbon bar, click the Dynamic Edit button. Notice that the profile, its dimensions, and the profile plane are displayed in the graphic window.

Edit the feature

In the graphic window, position the cursor over the 130 mm dimension, then click to select it. If required, use QuickPick to select the dimension.

On the Edit Definition command bar, type 110, then press the Enter key.

46

Notice the model size updates, and the features you copied and mirrored also update their position.

Continue editing dimensions

Edit the following dimensions, as shown in the illustration below: (1) Select the 90 mm dimension, then on the Dimension ribbon bar, type 120, and press the Enter key. (2) Select the 40 mm dimension, then on the Dimension ribbon bar, type 60, and press the Enter key.

Save the part

On the Quick Access toolbar, click the Save button to save the completed part.

47

Congratulations!
You have completed this tutorial. You have constructed a robust and easy to edit model. You have also learned important techniques that you can apply to a wide range of models. To learn more about Solid Edge, you can do the following: 1. Continue editing different features of the model until you understand all of the options available. 2. Select Solid Edge Help from the Help menu, and explore topics that are related to the subjects described in this tutorial. 3. Select Tutorials from the Help menu, and explore the other tutorials available with Solid Edge.

48