KVA Rating

Engine Model 4016-61TRG1

1269-1774 kWm(Gross)@1500 rpm
Power Rating
Basic Technical Data
Number of Cylinders 16
Compression Ratio 13:1 nominal
Tropical Weight
Dry 5570 kg
Wet 5847 kg
Tropical Overall Dimensions
Length 3302 mm
Width 1723 mm
Height 2128 mm
Moment of inertia
Engine 10.89 kgm2
Flywheel 9.55 kgm2
Total Engine Inertia
20.44 kgm2
(Engine +Flywheel)
General Installation Base load /prime power standby power
Gross Engine Power 50 @HZ @1500 RPM 1269 kWb / 1648 kWb 1774 kWb
Fan Power 90 kWm
Electropak nett Engine power 1179 kWm / 1558 kWm 1684 kWm
Combustion air flow 122 m3/min / 155m3/min 165m3/min
Exhaust Gas Temperature
375°C / 400 °C 425 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
400 m3/min
at atmospheric pressure
Mechanical Efficiency 94%
Engine coolant flow(Min) 21 liters/s
Typical Genset electrical output 1120 kWe / 1480kWe 1600 kWe
0.8pf 25°C(100kpa) 1400 Kva / 1850 kVA 2000 KVA
Total Lubrication System Capacity
Max Sump Capacity 213 liters
Lubricating oil Pressure
At Rated Speed 400 kpa
Min @80°C 340 kpa
oil filter Screen Spacing 40 microns
Shutdown Switch-Pressure setting 193 kpa
Oil Consumption
After running in
0.52g/kWhr at 1500 rpm
(typically after250 hrs)
Max air Intake Restriction of engine
Dirty filter 3.71 kpa
Fuel system
Recommended fuel to confirm to BS2869 Class A2 or BS EN590
Fuel inlet Temp to be less than 58 °C
Maximum suction head at pump inlet 2.5 Metres
fuel filter spacing 10 micron
Fuel consumption
Base load 192 g/kWh / 283 liters/hr
75% Prime 192 g/kWh / 280 liters/hr
50% Prime 192 g/kWh / 193 liters/hr
25% Prime 186 g/kWh / 103 liters/hr
Electrical system
Alternator voltage 24 volt
Alternator output 55 amps
Starter motor type 2x24 volt electric
Starter motor power 16.4KW
Number of Teeth on starter pinion 12
Cooling system
Total coolant Capacity:jacket water
Electropak-Tropical cooling
215 liters
(Engine and Radiator)
Total coolant Capacity:Secondary water
Electropak-Tropical cooling 170 liters
(charge coolers,pipework and Radiator)
Radiator:jacket water/secondary water
Tropical
Pressure cap setting (Min) 70 kpa
Water jacket Cooling data
Coolant flow 21 liters / s
Coolant Exit Temperature(Max) 98 °C
Coolant Inlet Temperature(Min) 70 °C
Coolant Inlet Temperature(Max) 80 °C
Secondary Water circuit
Coolant Flow 12 liters / s
Max Permissible restriction to coolant
see later kpa
pump flow
Coolant Exit Temperature(Max) dependent on ambient
Coolant Inlet Temperature(Min) 10 °C
Coolant Inlet Temperature(Max) refer to derate chart
Fan -Tropical
Type Temperate /tropical cooling
Diameter 1524 mm
Number of blades 8
Material aluminium
Drive ratio o:84
Pusher/puller pusher
Jacket water system
Max pressure in engine cooling circuit 170 kpa
Max top tank temperature 98 °C
Thermostat operating range 71-85 °C
Coolant Flow (Min) 1260 liters/min
Shutdown Switch setting 101 °C
Chargecooling or Secondary circuit
(Temperate)
Max pressure in secondary cooling circuit 100 kpa
Max Return temperature 63 °C
Max static pressure head on pump 70 kpa
Coolant Flow (Min) 720 liters /min
Chargecooling or Secondary circuit
(Tropical)
Max pressure in secondary cooling circuit 100 kpa
Max Return temperature 70 °C
Max static pressure head on pump 70 kpa
Coolant Flow (Min) 720 liters /min
Load acceptance(cold)
initial load prime power 63%
second load prime power 37%
 2000-2250 KVA

4016-61TRG2 4016-61TRG3
1437-1985 kWm(Gross)@1500 rpm 1600-2183 kWm(Gross)@1500 rpm

16 16
13:1 nominal 13:1 nominal

7783 kg 8203 kg
8361 kg 8861 kg

4542 mm 4562 mm
2185 mm 2185 mm
3175 mm 3736 mm

10.89 kgm2 10.89 kgm2

9.55 kgm2 9.55 kgm2
20.44 kgm2 20.44 kgm2

Base load /prime power standby power Base load /prime power standby power
1437 kWb / 1774 kWb 1985 kWb 1600 kWb / 1975 kWb 2183 kWb
90 kWm 100 kWm
1437 kWm / 1684 kWm 1895 kWm 1500 kWm / 1875 kWm 2083 kWm
131 m3/min / 158m3/min 175m3/min 135 m3/min / 160 m3/min 175 m3/min
425 °C / 457 °C 489 °C 460 °C / 475 °C 560 °C

475 m3/min 525 m3/min

94% 94%
21 liters/s 21 liters/s
1280 kWe / 1600kWe 1800kWe 1440 kWe / 1800kWe 2000kWe
1600 Kva / 2000kVA 2250 KVA 1800 Kva / 2250kVA 2500 KVA

213 liters 213 liters

400 kpa 400 kpa

340 kpa 340 kpa
40 microns 40 microns
193 kpa 193 kpa

0.52g/kWhr at 1500 rpm 0.52g/kWhr at 1500 rpm

3.71 kpa 3.71 kpa

BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590

 58 °C 58 °C
2.5 Metres 2.5 Metres
10 micron 10 micron

195 g/kWh / 325 liters/hr 200 g/kWh / 371 liters/hr

195 g/kWh / 306 liters/hr 200 g/kWh / 349 liters/hr
192 g/kWh / 208 liters/hr 204 g/kWh / 246 liters/hr
188 g/kWh / 111 liters/hr 220 g/kWh / 145 liters/hr

24 volt 24 volt
55 amps 55 amps
2x24 volt electric 2x24 volt electric
16.4KW 16.4KW
12 12

252 liters 270 liters

300 liters 230 liters

70 kpa 70 kpa

23 liters / s 21 liters / s
98 °C 98 °C
70 °C 70 °C
80 °C 80 °C

12 liters / s 12 liters / s
see later kpa see later kpa
dependent on ambient dependent on ambient
10 °C 10 °C
refer to derate chart refer to derate chart

Tropical cooling Temperate /tropical cooling

1905 mm 1905 mm
13 13
aluminium aluminium
o:6 o:6
pusher pusher

170 kpa 170 kpa

98 °C 98 °C
 71-85 °C 71-88 °C
1260 liters/min 1260 liters/min
101 °C 101 °C

100 kpa 100 kpa

68 °C 65 °C
70 kpa 70 kpa
720 liters /min 720 liters /min

100 kpa 100 kpa

60 °C 60 °C
70 kpa 60 kpa
720 liters /min 720 liters /min

58.50% 52%
41.50% 48%
KVA Rating 1500 1700 KVA

Engine Model 4012-46TAG0A 4012-46TAG1A 4012-46TAG2A 4012-46AG3A

1230KW Gross @1500 rpm 1335KW Gross @1500 rpm 1467kW (Gross)@1500 rpm 1699 kW(Gross)@1500 rpm
Power Rating
Basic Technical Data
Number of Cylinders 12 12 12 12
Compression Ratio 12.8 : 1 12.8 : 1 12.8 : 1 12.8 : 1
Tropical Weight
Dry 5690 kg 5690 kg 5690 kg 5860 kg
Wet 6050 kg 6050 kg 6050 kg 6230 kg
Tropical Overall Dimensions
Length 3915 mm 3915 mm 3915 mm 3913 mm
Width 2200 mm 2200 mm 2200 mm 2200 mm
Height 2269 mm 2269 mm 2269 mm 2614 mm
Moment of inertia
Engine Rotational components
9.46 kgm2 9.46 kgm2 9.46 kgm2 7.13 kgm2
(excluding flywheel)
Flywheel and starter ring 9.55 kgm2 9.55 kgm2 9.55 kgm2 9.55 kgm2
50 @HZ @1500 RPM 50 @HZ @1500 RPM 50 @HZ @1500 RPM 60 @HZ @1800 RPM
General Installation Base load /prime power standby power Base load /prime power standby power Base load /prime power standby power Base load /prime power standby power
Gross Engine Power 914 kW / 1125 Kw 1230 kW 981 kW / 1220 Kw 1335 kW 1077 kW / 1339 Kw 1467 kW 1286 kW / 1526 kW 1669 kW
Mean piston speec 9.5 m/s 9.5 m/s 9.5 m/s 11.4 m/s
Mechanical net Engine power Tropical 842 kW / 1053 kW 1158 kW 909 kW / 1148 kW 1263 kW 1005 kW / 1267 kW 1395 kW 1200 kW / 1440 kW 1583 kW
Combustion air flow 92.3 m3/min / 103.7 m3/min 108.5 m3/min 103.1 m3/min / 118.9 m3/min 125m3/min 113.1 m3/min / 126.4m3/min 136m3/min 128 m3/min / 144 m3/min 150.8 m3/min
Exhaust Gas Temperature
363°C / 383 °C 392 °C 382°C / 407 °C 419 °C 395 °C / 420 °C 434 °C 375 °C / 395 °C 405 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
198.8 m3/min /229 m3/min 243.1 m3/min 228.6 m3/min /272.2 m3/min 293.6 m3/min 255.8 m3/min /295.2 m3/min 324.6 m3/min 281.3 m3/min /324.3 m3/min 344.9 m3/min
at atmospheric pressure
Overall thermal Efficiency (Gross) 41.5 % /42.4 % 42.70% 40.2% /29.9 % 39.80% 39% /39.7 % 38.7% 39.7 % /39.6 % 39.9%
Assumed Alternator efficiency 95% 95% 95% 95%
Typical Genset electrical output 800 kWe / 1000kWe 1100 kWe 864 kWe / 1001kWe 1200 kWe 955 kWe / 1204 kWe 1325 kWe 1140 kWe / 1368kWe 1504 kWe
0.8pf Tropical 1000 Kva / 1250 kVA 1375 KVA 1079 Kva / 1363 kVA 1500 KVA 1193 Kva / 1505 kVA 1657 KVA 1425 Kva / 1710 kVA 1880 KVA
Total Lubrication System Capacity
Max Sump Capacity 157.5 liters 157.5 liters 157.5 liters 157.5 liters
Lubricating oil Pressure
Relief valve opening pressure 400 kpa 400 kpa 400 kpa 400 kpa
Min oil pressure 340 kpa 340 kpa 340 kpa 340 kpa
oil pressure at max no load speed 400 kpa 400 kpa 400 kpa 400 kpa
oil flow at rated speed 360 liters /min 360 liters /min 360 liters /min 420 liters /min
Shutdown Switch-Pressure setting
Oil Consumption
After running in
0.26 % of fuel 0.27 % of fuel 0.26 % of fuel 0.2 % of fuel
(typically after250 hrs)
Max air Intake Restriction of engine
Dirty filter 4 kpa 4 kpa 4 kpa 5 kpa
Fuel system
Recommended fuel to confirm to BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590
Fuel inlet Temp to be less than 58 °C 58 °C 58 °C 58 °C
Maximum suction head at pump inlet 2.5 Metres 2.5 Metres 2.5 Metres 2.5 Metres
filteration media size 10 micron 10 micron 10 micron 10 micron
Fuel consumption 1220kw @1500 rpm 1220kw @1500 rpm 1339 kw @1500 rpm 1526 kw @1800 rpm
100% Prime 199 g/kWh 211 g/kWh 213 g/kWh 213 g/kWh
75% Prime 204 g/kWh 212 g/kWh 218 g/kWh 214 g/kWh
50% Prime 216 g/kWh 226 g/kWh 223 g/kWh 215 g/kWh
Electrical system
Alternator voltage 24 volt 24 volt 24 volt 24 volt
Alternator output 55 amps 55 amps 55 amps 55 amps
Starter motor type 24 volt 24 volt 24 volt 24 volt
Starter motor power 16.4KW 16.4KW 16.4KW 16.4KW
Number of Teeth on starter pinion 12 12 12 12
Cooling system
Total coolant Capacity:jacket water
Electropak-Tropical cooling
223 liters 223 liters 223 liters 223 liters
(Engine and Radiator)
max static Pressure head on pump 70 kpa 70 kpa 70 kpa 70 kpa
Water jacket Cooling data 50 HZ @ 1500 rpm 50 HZ @ 1500 rpm 50 HZ @ 1500 rpm 60 HZ @ 1800 rpm
Max Coolant flow at Max restriction 970 liters / s 970 liters / s 970 liters / s 1140 liters / s
Engine coolant circuit -Max allowed Restriction 20 kpa 20 kpa 20 kpa 20 kpa
Charge air cooler restriction at full load (Max) 12 kpa 12 kpa 12 kpa 13 kpa
Compressor outlet temp at
183 °C 183 °C 206 °C 210 °C
std 25 °C test condition
Compressor outlet pressure at
240 kpa 240 kpa 245 kpa 248 kpa
std 25 °C test condition
Charge air cooler temp at
45 °C 45 °C 45 °C 45 °C
std 25 °C test condition
Fan -Tropical
Type Mechanical ,fixed Mechanical ,fixed Mechanical ,fixed Mechanical ,fixed
Diameter 1650 mm 1650 mm 1650 mm 1890 mm
Number of blades 10 10 10 10
Material
Drive ratio o:79 o:79 o:79 o:61
Pusher/puller pusher pusher pusher pusher
Jacket water system
Max pressure in engine cooling circuit
Max top tank temperature 98 °C 98 °C 98 °C 98 °C
Thermostat operating range 71-85 °C 71-85 °C 71-85 °C 71-85 °C
Water temp switch or alarm setting 103 °C 103 °C 103 °C 101 °C
Load acceptance(cold)
initial load prime power
The engine governing complies with the requirements of classification 4 & 4 of ISO 8528-12 and to G2 and G3 operating linits stated under ISO 8528-5
second load prime power
KVA Rating 1010 KVA

Engine Model 4008TAG1A & 4008TAG2A 4008-30TAG1 4008-30TAG2

842KW @1500 rpm 947KW @1500 rpm
Power Rating
Basic Technical Data
Number of Cylinders 8 8 8
Compression Ratio 13.6:1 nominal 13.6:1 nominal 13:01
Tropical Weight
Dry 4320 kg 4217 kg 4217 kg
Wet 4618 kg 4473 kg 4473 kg
Tropical Overall Dimensions
Length 3711 mm 3468 mm 3468 mm
Width 2046 mm 2194 mm 2194 mm
Height 2146 mm 1919 mm 1919 mm
Moment of inertia
Engine 9.60 kgm2 9.60 kgm2 9.60 kgm2
Flywheel 6.02 kgm2 6.02 kgm2 6.02 kgm2
Total Engine Inertia
(Engine +Flywheel)
General Installation Base load /prime power standby power Base load /prime power standby power Base load /prime power standby power
Gross Engine Power 50 @HZ @1500 RPM 644 kWb / 805 kWb 882 kWb 682 kWb / 808 kWb 892 kWb 724 kWm / 892 kWm 997 kWb
Fan Power 38 kWm 50 kWm 50 kWm
net Engine power 602 kWm / 767 kWm 844 kWm 632 kWm / 758 kWm 842 kWm 674 kWm / 842 kWm 947 kWm
Combustion air flow 58 m3/min / 69.4 m3/min 74 m3/min 59 m3/min / 69.5 m3/min 77 m3/min 62.5 m3/min / 77 m3/min 84 m3/min
Exhaust Gas Temperature
405°C / 425 °C 440 °C 450 °C / 465 °C 470 °C 460 °C / 470 °C 480 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
183 m3/min 130 m3/min /160 m3/min 185 m3/min 145 m3/min /185 m3/min 203 m3/min
at after turbo
Mechanical Efficiency 88% / 91 % 92% 92% 92%
Engine coolant flow(Min) 10 liters/s 630 liters/min 630 liters/min
Typical Genset electrical output 576 kWe / 728kWe 802 kWe 600 kWe / 720 kWe 800 kWe 640 kWe / 800 kWe 900 kWe
0.8pf 25°C(100kpa) 720 Kva / 911 kVA 1002 KVA 750 Kva / 900 kVA 1000 KVA 800 Kva / 1000 kVA 1125 KVA
Total Lubrication System Capacity
Max Sump Capacity 153 liters 153 liters 153 liters
Lubricating oil Pressure
At Rated Speed 340 kpa 340 kpa 340 kpa
Min @80°C 240 kpa 240 kpa 240 kpa
oil filter Screen Spacing 40 microns 40 microns 40 microns
Shutdown Switch-Pressure setting 193 kpa 193 kpa 193 kpa
Oil Consumption
After running in 4008TAG1A 0.50 g/kWhr
0.4 g/kWhr at 1500 rpm 0.4 g/kWhr at 1500 rpm
(typically after250 hrs) 400TAG2A 0.52 g/kWhr
Max air Intake Restriction of engine
Dirty filter 380 mm H2O 5.5 kpa 5.5 kpa
Fuel system
Recommended fuel to confirm to BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590 BS2869 Class A2 or BS EN590
Fuel inlet Temp to be less than 58 °C 58 °C 58 °C
Maximum suction head at pump inlet 2.5 Metres 2.5 Metres 2.5 Metres
fuel filter spacing 10 micron 10 micron 10 micron
Fuel consumption 4008TAG1A 4008TAG2A
Base load 203 g/kWh / 154 liters/hr 205 g/kWh / 175 liters/hr 225g/kWh / 154 liters/hr 202 g/kWh / 170 liters/hr
75% Prime 201 g/kWh / 143 liters/hr 203 g/kWh / 163 liters/hr 225 g/kWh / 144 liters/hr 202 g/kWh / 157 liters/hr
50% Prime 207 g/kWh / 98 liters/hr 206 g/kWh / 109 liters/hr 230 g/kWh / 109 liters/hr 210 g/kWh / 110 liters/hr
25% Prime 217 g/kWh / 52 liters/hr 218 g/kWh / 59 liters/hr
Electrical system
Alternator voltage 24 volt 24 volt 24 volt
Alternator output 40 amps 55 amps 55 amps
Starter motor type 24 volt electric 24 volt electric 24 volt electric
Starter motor power 8.2KW 8.2KW 8.2KW
Number of Teeth on starter pinion 12 12 12
Cooling system
Total coolant Capacity:jacket water
Electropak-Tropical cooling
149 liters 140 liters 140 liters
(Engine and Radiator)
Total coolant Capacity:Secondary water
Electropak-Tropical cooling liters liters liters
(charge coolers,pipework and Radiator)
Radiator:jacket water/secondary water
Tropical
Pressure cap setting (Min) 69 kpa 70 kpa 70 kpa
Water jacket Cooling data
Coolant flow 10 liters / s 630 liters / min 630 liters / min
Coolant Exit Temperature(Max) 98 °C 98 °C 98 °C
Coolant Inlet Temperature(Min) 70 °C 70 °C 70 °C
Coolant Inlet Temperature(Max) 86 °C 86 °C 86 °C
Fan -Tropical
Type Incorporated in radiator Axial flow Axial flow
Diameter 1400 mm 1250 mm 1250 mm
Number of blades 9 9
Material aluminium aluminium
Drive ratio o:94 o:94
Pusher/puller pusher
Jacket water system
Max pressure in engine cooling circuit 170 kpa
Max top tank temperature 98 °C 98 °C 98 °C
Thermostat operating range 71-85 °C 84-93 °C 84-93 °C
Coolant Flow (Min) 20 kpa 630liters/min 630liters/min
Shutdown Switch setting 101 °C 101 °C 101 °C
Load acceptance(cold)
initial load prime power 64% 57% 35% 35%
second load prime power 36% 43% 65% 65%
KVA Rating 750 KVA

Engine Model 4006-23TAG2A

Power Rating 721KWm Gross @1500 rpm
746 KWm @1800 rpm
Basic Technical Data
Number of Cylinders 6
Compression Ratio 13:01
Tropical Weight Engine only
Dry 2524 kg
Wet 2663 kg
Tropical Overall Dimensions
Length 3027 mm
Width 1706 mm
Height 1964 mm
Moment of inertia
Flywheel 6.02 kgm2
Engine @ 1800 rpm 4.59 kgm2
50 @HZ @1500 RPM 60 @HZ @1800 RPM
General Installation Base load /prime power standby power Base load /prime power standby power
Gross Engine Power 531 kWm / 658 Kwm 721 kWm 555 kWm / 682 Kw 746 kW
Fan and battery charging alternator
26KW 44KW
power Typical (trop)
Mechanical net Engine power 505 kWm / 632 kWm 695 kWm 511 kWm / 638 kWm 702 kWm
Combustion air flow 60 m3/min / 64 m3/min 71 m3/min 62 m3/min / 65 m3/min 72 m3/min
Exhaust Gas Temperature
430 °C 430 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
180 m3/min 190 m3/min
at atmospheric pressure
Mechanical efficiency (nett) 90% 90%
Engine coolant flow 600 liters /s 600 liters /s
Total Lubrication System Capacity
Max Sump Capacity 113 liters
Lubricating oil Pressure
at rated speed 350 kpa
Min oil pressure 240 kpa
oil filter screen spacing 40micron
Shutdown Switch-Pressure setting 193 kpa
Oil Consumption
After running in 0.52 g/kWhr @ 1500 rpm
(typically after250 hrs) 0.7 g/Kwhr @ 1800 rpm
Max air Intake Restriction of engine
Dirty filter 3.8 kpa
Fuel system
Recommended fuel to confirm to BS2869 1998 Class A1,A2 or BS EN590
Fuel inlet Temp to be less than 58 °C
Maximum suction head at pump inlet 2.5 Metres
filteration media size 10 micron
Fuel consumption 1500 rpm 1800 rpm
Base power 203 g/kWh /126 liters/hr 212 g/kWh /135 liters/hr
75% Prime 204 g/kWh / 117 liters/hr 214 g/kWh / 126 liters/hr
50% Prime 208 g/kWh /80 liters/ s 224 g/kWh /88 liters/ s
Electrical system
Alternator voltage 24 volt
Alternator output 55 amps
Starter motor type 24 volt
Starter motor power 7.5 KW
Number of Teeth on starter pinion 12
Cooling system
Total coolant Capacity:jacket water
Electrounit-engine only 36 liters
max static Pressure head on pump 70 kpa
Water jacket Cooling data 1500 rpm 1800 rpm
Coolant flow 600 liters / min 720 liters / min
coolant exit temp(max) 98 °C 98 °C
Coolant Inlet temp (Min) 70 °C 70 °C
Coolant Inlet temp (Max) 85 °C 85 °C
Fan -Tropical
Type
Diameter
Number of blades
Material
Drive ratio
Pusher/puller
Jacket water system
Max pressure in engine cooling circuit 170 kpa
Max top tank temperature 98 °C
Thermostat operating range 71-85 °C
Water temp switch or alarm setting
Load acceptance(cold)
prime power @1500 rpm 67%
prime power @1800 rpm 70%
KVA Rating 400 KVA

Engine Model 2206A-E13TAG2 2206A-E13TAG3 2206A-E13TAG5

Power Rating 368.4 KW @1500 RPM 412.5 KW @1500 RPM 412.5 KW @1500 RPM
406.5 KW @1800 RPM 406.5 KW @1800 RPM 406.5 KW @1800 RPM
Basic Technical Data
Number of Cylinders 6 6 6
Compression Ratio 16.3 :1 16.3 :1 16.3 :1
Tropical Weight Of Electropak
Dry 1478 kg 1478 kg 1478 kg
Wet 1582 kg 1582 kg 1582 kg
Tropical Overall Dimensions
Length 2410 mm 2410 mm 2410 mm
Width 1120 mm 1120 mm 1120 mm
Height 1725 mm 1725 mm 1725 mm
Moment of inertia
Filywheel 1.36 kgm2 1.36 kgm2 1.36 kgm2
Engine @ 1800 rpm 1.41 kgm2 1.41 kgm2 1.41 kgm2
50 HZ @1500 60 HZ @1800 50 HZ @1500 60 HZ @1800 50 HZ @1500 60 HZ @1800
General Installation prime power/Stand by prime power/Stand by prime power/Stand by prime power/Stand by prime power/Stand by prime power/Stand by
Gross Engine Power 324.2 kWb /368.4 kWb 373.4 kWb /406.5 kWb 368.4 kWb / 412.5 KWb 373.4 kWb / 406.5 KWb 324.2 kWb / 368.4 KWb 373.4 kWb / 406.5 KWb
Brake mean effective pressure(BMEP) 2061 kpa /2355kpa 2061 kpa /2355kpa 2344 kpa /2637kpa 1984 kpa /2171kpa 2063 kpa /2357kpa 1995 kpa /2182kpa
net Engine power
Combustion air flow at rated speed 21.3 m3/min / 23.6 m3/min 27.4 m3/min / 29 m3/min 24.3 m3/min / 26.4 m3/min 27.4 m3/min / 29 m3/min 19.8 m3/min / 22 m3/min 23.8 m3/min / 25.7 m3/min
Exhaust Gas Temperature
630 °C 630 °C / 660 °C 630 °C 630 °C / 660 °C 630 °C 680 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
56.6 m3/min / 64.8 m3/min 67.5 m3/min / 73.5 m3/min 64.6 m3/min / 72.5 m3/min 67.5 m3/min / 73.5 m3/min 58.7 m3/min / 66.9 m3/min 67.5 m3/min / 74.5 m3/min
at after turbo
Overall Thermal efficiency(net) 41.3 % / 40.8 % 40,7 % /40.3% 41.4 % / 40.9 % 40.7 % /40.3% 39 % / 40.5 % 40 % /39.6%
Assumed alternator efficiency 92% 92% 92%
Typical Genset electrical output 280 kWe / 320kWe 320 kWe / 350kWe 320 kWe / 360kWe 320 kWe / 350kWe 280 kWe / 320kWe 320 kWe / 350kWe
0.8pf 25°C(100kpa) 350 Kva / 400 kVA 400 Kva / 438 kVA 400 Kva / 450 kVA 400 Kva / 438 kVA 350 Kva / 400 kVA 400 Kva / 438 kVA
Total Lubrication System Capacity
Max Sump Capacity 40 liters 40 liters
Lubricating oil Pressure 1500 rpm 1800 rpm 1500 rpm 1800 rpm 1500 rpm 1800 rpm
Oil flow 140 liters/min 172 liters/min 140 liters/min 172 liters/min 140 liters/min 172 liters/min
oil pressure at bearings 310 kpa 358 kpa 310 kpa 358 kpa 310 kpa 358 kpa
oil pressure at bearings at minimum 270 kpa 270 kpa
Shutdown Switch-Pressure setting
Oil Consumption
0.15% of fuel 0.1% of fuel
oil consumption at full load as a % of fuel consumption
Max air Intake Restriction of engine
Dirty filter 6.4 kpa 6.4 kpa
Fuel system
Recommended fuel to confirm to BS2869 1998 Class A1,A2 or BS EN590 BS2869 1998 Class A1,A2 or BS EN590
Fuel inlet Temp to be less than 55 °C 55 °C
Maximum suction head at pump inlet 3 Metres 3 Metres
filteration media size 10 micron 10 micron
Fuel consumption 1500 rpm 1800 rpm 1500 rpm 1800 rpm 1500 rpm 1800 rpm
100% prime 196 g/kWh /71 liters/hr 196 g/kWh /81 liters/hr 197 g/kWh /81 liters/hr 196 g/kWh /81 liters/hr 207 g/kWh /75 liters/hr 201 g/kWh /83 liters/hr
75% Prime 198 g/kWh / 54 liters/hr 199 g/kWh / 62 liters/hr 199 g/kWh / 62 liters/hr 199 g/kWh / 62 liters/hr 211 g/kWh / 57 liters/hr 204 g/kWh / 63 liters/hr
50% Prime 203 g/kWh /37 liters/ s 205 g/kWh /43 liters/ s 202 g/kWh /42 liters/ s 205 g/kWh /43 liters/ s 219 g/kWh /40 liters/ s 209 g/kWh /44 liters/ s
Electrical system
Alternator voltage 24 volt 24 volt
Alternator output 70 amps 70 amps
Starter motor type 24 volt 24 volt
Starter motor power 7.8 KW 7.8 KW
Number of Teeth on starter pinion 11 11
Cooling system
Total coolant Capacity:jacket water
Total system capacity 51.4 lit 51.4 lit
max static Pressure head on pump 30 kpa 30 kpa
Water jacket Cooling data 1500 rpm 1800 rpm 1500 rpm 1800 rpm 1500 rpm 1800 rpm
Coolant flow against 30kpa restriction 5.3 liters / sec 6.7 liters / sec 5.3 liters / sec 6.7 liters / sec 5.3 liters / sec 6.7 liters / sec
Max pressure in engine cooling circuit 70 kpa 70 kpa
Max top tank temperature 104 °C 104 °C
Thermostat operating range 87-98 °C 87-98 °C
Water temp switch or alarm setting
FAN
Type Pusher Pusher
Diameter 927mm 927mm
Number of blades 9 9
Material composite composite
Drive ratio 0.92:1 0.92:1
Pusher/puller Pusher Pusher
Load acceptance(cold) 1500 rpm 1800 rom 1500 rpm 1800 rom 1500 rpm 1800 rom
Initial load 66% 80% 58% 80% 60% 68%
Second load 73% 85% 65% 85% 65% 85%
KVA Rating 500 KVA

Engine Model 2506C-E15TAG1 2506C-E15TAG2 2506D-E15TAG1

Power Rating 451 KW @1500 RPM 495 KW @1500 RPM
514.0 kW @1800 rpm
514 KW @1800 RPM 514 KW @1800 RPM
Basic Technical Data
Number of Cylinders 6 6 6
Compression Ratio 16:01 .16:1 .16:1
Tropical Weight Of Electropak
Dry 1633 kg(Engine only) 1633 kg(Engine only) 1633 kg(Engine only)
Wet 1714 kg 1714 kg 1714 kg
Tropical Overall Dimensions
Length 2657 mm 2657 mm 2657 mm
Width 1120 mm 1120 mm 1120 mm
Height 1718 mm 1718 mm 1718 mm
Moment of inertia
Flywheel (1500 rpm & 1800 rpm) 1.96 kgm2 1.96 kgm2 1.96 kgm2
Engine (1500 rpm & 1800 rpm) 2.3 kgm2 2.3 kgm2 2.3 kgm2
50 HZ @1500 60 HZ @1800 50 HZ @1500 60 HZ @1800 60 HZ @1800
General Installation prime power/Stand by prime power/Stand by prime power/Stand by prime power/Stand by prime power/Stand by
Gross Engine Power 412 kWb /451 kWb 458 kWb /514 kWb 451 kWb /495 kWb 458 kWb /514 kWb 458 kWb / 514 KWb
Fan power 8.8kWm 15.5kWm 8.8kWm 15.5kWm 15.5kWm
Electropak net Engine power 396kWm / 435 kWm 435kWm / 490 kWm 435kWm / 478 kWm 435kWm / 490 kWm 435kWm / 490 kWm
Combustion air flow at rated speed 21.3 m3/min / 23.6 m3/min 27.4 m3/min / 29 m3/min 35.8 m3/min / 36.6 m3/min 34.3 m3/min / 38 m3/min 39.3 m3/min / 41.5 m3/min
Exhaust Gas Temperature
630 °C 630 °C / 660 °C NA/550 °C NA/550 °C NA/550 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
33 m3/min /35.8 m3/min 34.3 m3/min / 38 m3/min 94m3/min / 98 m3/min 96 m3/min / 105.3 m3/min 104.5 m3/min / 112 m3/min
at after turbo
Overall Thermal efficiency(net) 39.9 % / 39.7 % 44 % /43.4% 39.7 % / 39.6 % 44 % /43.4% 37.4 % / 38.4 %
Assumed alternator efficiency 92% 92% 92%
Typical Genset electrical output 364 kWe / 400kWe 400 kWe / 450 kWe 400 kWe / 440kWe 400 kWe / 450kWe 400 kWe / 450kWe
0.8pf 25°C(100kpa) 455 Kva / 500 kVA 500 Kva / 563 kVA 400 Kva / 550 kVA 500 Kva / 563 kVA 500 Kva / 563 kVA
Total Lubrication System Capacity
Max Sump Capacity 62 liters 62 liters
Lubricating oil Pressure
At rated speed 420 kpa 420 kpa
Nominal Minimum 200 kpa 200 kpa
oil Relief valve open 620 kPa 620 kPa
Shutdown Switch-Pressure setting
Oil Consumption
0.1% of fuel 0.1% of fuel
oil consumption at full load as a % of fuel consumption
Max air Intake Restriction of engine
Dirty filter 6.2 kpa 6.2 kpa
Fuel system
Recommended fuel to confirm to
Fuel inlet Temp to be less than 55 °C 55 °C
Maximum suction head at pump inlet 3 Metres 3 Metres
filteration media size 10 micron 10 micron
Fuel consumption 1500 rpm 1800 rpm 1500 rpm 1800 rpm 1500 rpm
100% prime 216 g/kWh /99 liters/hr 199 g/kWh /100 liters/hr 211 g/kWh /106 liters/hr 199 g/kWh /100 liters/hr 225 g/kWh /113 liters/hr
75% Prime 212 g/kWh / 73 liters/hr 204 g/kWh / 77 liters/hr 215 g/kWh / 81 liters/hr 204 g/kWh / 77 liters/hr 245 g/kWh / 93 liters/hr
50% Prime 222 g/kWh /51 liters/ s 217 g/kWh /57 liters/ s 220 g/kWh /55 liters/ s 217 g/kWh /55 liters/ s 267 g/kWh /67 liters/ s
Electrical system
Alternator voltage 24 volt 24 volt
Alternator output 70 amps 70 amps
Starter motor type 24 volt 24 volt
Starter motor power 7.5 KW 7.5 KW
Number of Teeth on starter pinion 11 11
Cooling system
Total coolant Capacity:jacket water
Total system capacity 58 liter 58 liter
max static Pressure on pump 30 kpa 30 kpa
Water jacket Cooling data
Coolant flow against 30kpa restriction 5.3 liters / sec
Max pressure in engine cooling circuit 276 kpa 70 kpa
Max top tank temperature 107 °C 107 °C
Thermostat operating range 88-98 °C 88-98 °C
Water temp switch or alarm setting
FAN
Type Pusher Pusher
Diameter 927mm 927mm
Number of blades 9 9
B3WG6 or PA6GF30 Nylon 6
B3WG6 or PA6GF30 Nylon 6 glass filled 30%
Material glass filled 30%
Drive ratio 0·92:1 0.92:1
Pusher/puller Pusher Pusher
Load acceptance(cold) 1500 rpm 1800 rom 1500 rpm 1800 rom 1800 rpm
Initial load 65% 65% 60% 55% 65%
Second load 60% 60% 65% 60% 60%
KVA Rating 625 KVA 625 KVA 625 KVA

Engine Model 2806C-E18TAG1 2806C-E18TAG3 2806D-E18TAG1A

Power Rating 583.8 KW Gross @1500 rpm 584 KW Gross @1500 rpm
623 KWm @1800 rpm 678 KWm @1800 rpm 593 KW @1800 rpm
Basic Technical Data
Number of Cylinders 6 6 6
Compression Ratio 14.5:1 14.5:1 18:01
Tropical Weight Engine only
Dry 2050 kg 2050 kg 2079 kg
Wet 2158 kg 2158 kg
Tropical Overall Dimensions
Length 2545 mm 2545 mm 2408 mm
Width 1536 mm 1536 mm 1455 mm
Height 1807.5 mm 1807.5 mm 1805 mm
Moment of inertia
Flywheel 4.74 kgm2 AT 1500 /1800 rpm 4.74 kgm2 at 1500 /1800 rpm 1.92 kgm2
Engine 2.31 kgm2 /2.70 kgm2 AT 1500 /1800 rpm 2.31 kgm2 /2.70 kgm2 at 1500 /1800 rpm 2.48 kgm2
50 @HZ @1500 RPM 60 @HZ @1800 RPM 50 @HZ @1500 RPM 60 @HZ @1800 RPM 50 @HZ @1500 RPM
General Installation prime power standby power prime power standby power prime power standby power prime power standby power prime power standby power
Gross Engine Power 532 Kwb 583.8 kWm 568 Kw 623 kW 540 Kwb 584 kWm 617.5 Kw 678 kW 540 Kwb 593 kWm
Fan and battery charging alternator
9 KWm 15 KWm 9 KWm 15 KWm 9 KWm
power Typical (trop)
Mechanical net Engine power 514 kWm 565 kWm 543 kWm 598 kWm 522 kWm 565 kWm 592 kWm 652 kWm 522 kWm 574 kWm
Combustion air flow 40 m3/min 41 m3/min 45 m3/min 47 m3/min 38 m3/min 40 m3/min 49 m3/min 52 m3/min 40.2 m3/min 41.1 m3/min
Exhaust Gas Temperature
550 °C 565 °C 487 °C 507 °C 566 °C 567 °C 527 °C 554 °C 518 °C 531 °C
after Turbo(Max)
Exhaust Gas Flow(Max)
110 m3/min 115 m3/min 114 m3/min 122 m3/min 106 m3/min 114 m3/min 130 m3/min 141 m3/min 108.5 m3/min 110.5 m3/min
at atmospheric pressure
Overall thermal efficiency (nett) 40% 42% 42% 43% 43% 40.6% 41.6% 41.0% 40%
Engine coolant flow 6.1 liters /s 7.2 liters /s 6.1 liters /s 7.2 liters /s 6.1 liters /s
473 kWe 520 kWe 500 kWe 550 kWe 480 kWe 520 kWe 545 kWe 600 kWe 480 kWe 528 kWe
Typical Genset electrical output
591 kVA 650 kVA 625 kVA 687 kVA 600 kVA 650 kVA 681 kVA 750 kVA 600 kVA 660 kVA
0.8pf 25°C(100kpa)
assumed alternator efficiency 92% 92% 92%
Total Lubrication System Capacity
Max Sump Capacity 62 liters 62 liters 71 liters
Lubricating oil Pressure
at rated speed 420 kpa 420 kpa 375 kpa
Min oil pressure 200 kpa 200 kpa 250 kpa
oil filter screen spacing 30micron 30micron 30micron
Shutdown Switch-Pressure setting
Oil Consumption
After running in
0.1% of fuel 0.1% of fuel 0.15% of fuel
(typically after250 hrs)
Max air Intake Restriction of engine
Dirty filter 6.35 kpa 6.35 kpa 6.2 kpa
Fuel system
Recommended fuel to confirm to BS2869 1998 Class A1,A2 or BS EN590 BS2869 1998 Class A1,A2 or BS EN590 BS2869 1998 Class A1,A2 or BS EN590
Fuel inlet Temp to be less than 79 °C
Maximum suction head at pump inlet 3 Metres 3 Metres 3 Metres
filteration media size 10 micron 10 micron 10 micron
Fuel consumption 1500 rpm 1800 rpm 1500 rpm
Base power 203 g/kWh /123 liters/hr 211 g/kWh /145 liters/hr 204 g/kWh /129.6 liters/hr
75% Prime 211 g/kWh / 96 liters/hr 217 g/kWh / 112 liters/hr 213 g/kWh / 101.8 liters/hr

221 g/kWh /67 liters/ s 230 g/kWh /79 liters/ s 219 g/kWh /69.6 liters/ s
50% Prime
Electrical system
Alternator voltage 24 volt 24 volt 24 volt
Alternator output 70 amps 70 amps 45 amps
Starter motor type 24 volt 24 volt 24 volt
Starter motor power 9 KW 9 KW 9 KW
Number of Teeth on starter pinion 11 11 11
Cooling system
Total coolant Capacity:jacket water
Electrounit-engine + Radiator 61 liters 61 liters 61 liters
Nominal jacket water pressure in crankcase 280 kpa 280 kpa 280 kpa
Fan -Tropical
Type Pusher Pusher Pusher
Diameter 965mm 965mm 965mm
Number of blades 9 9 9
Material plastic plastic plastic
Drive ratio 0·8:1 0·8:1 0·8:1
Pusher/puller
Jacket water system
Max pressure in engine cooling circuit 280 kpa 280 kpa 280 kpa
Max top tank temperature 103 °C 103 °C 103 °C
Thermostat operating range 88-98 °C 88-98 °C 88-98 °C
Water temp switch or alarm setting
Load acceptance(cold)
prime power @1500 rpm
prime power @1800 rpm