10-45B-00 SRM-4510, B451 1

SERVICE DATA
TRIMMER/BRUSHCUTTER
ECHO: SRM-4510
(Serial number: U53726000001 - U53726999999

shindaiwa: B451
(Serial number: U53626000001 - U53626999999

INTRODUCTION CONTENTS
page
We are constantly working on technical im- 1 SERVICE INFORMATION............................... 2
provement of our products. For this reason, 1-1 Specifications.............................................. 2
technical data, equipment and design are 1-2 Technical data.............................................. 3
subject to change without notice. All speci- 1-3 Torque limits................................................ 4
fications and directions in this SERVICE 1-4 Special repairing materials.......................... 4
1-5 Service limits............................................... 5
DATA are based on the latest product infor-
1-6 Special tools................................................ 6
mation available at the time of publication.

Reference No. 10-45B-00

ISSUED: 202210

Copyright(C)2022 ECHO Incorporated, a subsidiary of YAMABIKO Corporation All rights reserved.

2 SERVICE INFORMATION SRM-4510, B451

1 SERVICE INFORMATION
1-1 Specifications
Dimensions Length* mm(in) 1792 (70.6)
Width mm(in) 693 (27.3)
Height mm(in) 440 (17.3)
2
Dry weight* kg(lb) 7.7 (17.0)
Engine Type YAMABIKO, air-cooled, two-stroke, single cylinder
Rotation Counterclockwise as viewed from the output end
Displacement cm3(in3) 45.7 (2.788)
Bore mm(in) 42.0 (1.654)
Stroke mm(in) 33.0 (1.299)
Compression ratio 6.6
Carburetor Type Diaphragm horizontal-draft with purge bulb
Model HLI HR02-2B01
Venturi size-Throttle bore mm(in) 13.5-15.0 (0.53-0.59)
Ignition Type CDI (Capacitor discharge ignition) system
Spark plug NGK BPM7A
Exhaust Muffler type Spark arrester muffler
Starter Type Automatic Rewind
Rope diameter x length mm(in) 3.8 x 900 (0.1 x 35.4)
Fuel*3 Type Mixed two-stroke fuel
Mixture ratio 50 : 1 (2 %)
Gasoline Minimum 89 octane
Two-stroke air cooled engine oil ISO-L-EGD (ISO/CD13738), JASO M345-FC/FD
Full tank capacity: 0.95 (32.1)
Tank capacity L (US.fl.oz.)
Usable capacity: 0.81 (27.4)
Clutch Type Centrifugal, 2-shoe pivot
Handle Type U-handle w/integrated control grip
Type Solid type with spline (10-tooth)
Diameter - Length mm (in) 8 - 1538 (0.3 - 60.6)
Drive shaft
OD-ID mm(in) 28.0 - 24.0 (1.1 - 0.9)
Housing (Main pipe)
Length mm(in) 1500 (59.1)
Gear case Reduction ratio 1:36
Gear tooth Spiral bevel gear
XTended Protection TM Lubricant or
Lubrication
RED ARMOR TM Lubicant (Lithium based grease)
Option: Nylon line cutter B6, Rapid-Loader™ 35
Cutter Type
3-tooth blade (255 mm)
Arbor diameter for blade mm (in) 25.4 (1.0)
Fastener type, size mm Left-hand thread M12 x 1.75 pitch
Cutting rotation Counterclockwise as viewed from top
OD: Outer diameter. ID: Inner diameter* Without guide bar and saw chain.
*1 Without Cutting attachment
*2 Without Cutting attachment and Shield
*3 Refer to Operator’s manual
SRM-4510, B451 SERVICE INFORMATION 3
1-2 Technical data
Engine
Compression pressure MPa (kgf/cm2) (psi) 0.75 (7.7) (109)
Clutch engagement speed RPM 4,000
Ignition system
Spark plug gap mm(in) 0.6 - 0.7 (0.024 - 0.028)
Spark test
Tester gap w/ spark plug mm(in) 4.0 (0.16)
Tester gap w/o spark plug mm(in) 6.0 (0.24)
Secondary coil resistance kΩ 1.25 - 1.65
Pole shoe air gaps mm(in) 0.3 - 0.4 (0.012 - 0.016)
Ignition timing at 3,000 RPM °BTDC 29
at 7,000 RPM °BTDC 27
Carburetor
Test Pressure, minimum MPa (kgf/cm2) (psi) 0.05 (0.5) (7.0)
Metering lever height mm(in) 1.65 (0.06) lower than diaphragm seat
Tool to adjust mixture needles Screwdriver 2.0 mm
Carburetor adjustment
Nylon line cutter B6 Rapid-Loader™ 35
Cutting head preparation
Line length*1 190 mm 205 mm
1) Initial setting
H mixture needle turn out 2 1/2
L mixture needle turn out 2 1/2
2
Throttle adjust screw turn in* 3 1/2
Engine warm-up Idle - WOT : Total sec. 10 - 50 : 120
2) Find idle maximum speed Adjust L mixture needle to maximum idle speed*3
3) Set idle maximum speed w/ TAS RPM 3,400
4) Set idle speed
RPM 2,700
by turning L mixture needle CCW
5) Find WOT maximum speed RPM Adjust H mixture needle to maximum WOT speed
Turn H mixture needle CCW to reduce WOT speed
6) WOT setting RPM
by : 200
Idle: 2500 - 3000
7) Verify final engine speed with standard WOT: 9200 - 10600 (With B6)
RPM
equipment 800 - 10800 (With Rapid-Loader™ 35)
11000 - 13000 (With Blade)
BTDC: Before top dead center. WOT: Wide open throttle
CCW: Counterclockwise TAS: Throttle adjust screw

*1 From eyelet on nylon head

*2 Set Throttle adjust screw to the point that its tip just contacts throttle plate before initial setting.
*3 If clutch engages during adjustment process 2), reduce engine speed by turning TAS CCW until clutch disengages
and then redo 2).
4 SERVICE INFORMATION SRM-4510, B451

1-3 Torque limits

Descriptions Size kgf•cm N•m in•lbf
Starter system Starter pulley M8 80 - 100 8 - 10 70 - 87
Starter pulley nut M8 160 - 200 16 - 20 140 - 175
Starter case M4* 20 - 30 2 - 3 17 - 26
Ignition system Magneto rotor (Flywheel) M10 250 - 290 25 - 29 220 - 255
Ignition coil M5 30 - 50 3 - 5 26 - 45
Fan cover M5 50 - 90 5 - 9 45 - 80
Spark plug M14 130 - 170 13 - 17 110 - 150
Fuel system Carburetor M5 40 - 50 4 - 5 35 - 45
Intake insulator M5 50 - 60 5 - 6 45 - 52
Fuel tank with bracket** M5* 70 90 7 9 60 80
Clutch Clutch shoe M8 160 - 200 16 - 20 140 - 175
Cylinder cover M5 30 - 45 3 - 4.5 25 - 40
Top guard M5 30 45 3 4.5 25 40
Engine Crankcase M5 70 - 110 7 - 11 60 - 95
Cylinder M5 70 - 110 7 - 11 60 - 95
Muffler M5 60 - 100 6 - 10 52 - 87
Muffler stay M5 50 - 70 5 - 7 45 - 60
Muffler cover M4 15 - 30 1.5 - 3 13 - 26
Other Cutter fastener LM12 280 - 320 28 - 32 245 - 280
Regular bolt, nut and screw M3 6 - 10 0.6 - 1 5 - 9
M4 15 - 25 1.5 - 2.5 13 - 22
M5 25 - 45 2.5 - 4.5 22 - 40
M6 45 - 75 4.5 - 7.5 40 - 65
M8 110 - 150 11 - 15 95 - 130

LM: Left hand thread

* Apply thread locking sealant. (See below)
** Fan cover side

1-4 Special repairing materials

Material Location Remarks
Grease Drive shaft
Gear case
Rewind spring XTended Protection TM Lubricant or RED ARMOR
TM Lubicant (Lithium based grease)
Starter center post
Oil seal inner lips
Thread locking sealant Starter case
Intake inulator ThreeBond #1324N or equivalent
Fuel tank with bracket
SRM-4510, B451 SERVICE INFORMATION 5
1-5 Service limits
A B C D

E F G H

K L M

0
1
2
0 3
5 4
10 5
6
7
8
9
10
11
12

Description mm (in)
A Cylinder bore When plating is worn and aluminum can be seen
B Piston outer diameter Min. 41.90 (1.650)
C Piston pin bore Max. 10.025 (0.3947)
D Piston ring groove 1st Max. 1.3 (0.051)
2nd Max 1.3 (1.051)
E Piston ring side clearance 1st Max. 0.15 (0.006)
2nd Max 0.1 (0.004)
F Piston pin outer diameter Min. 8.98 (0.3535)
G Piston ring width Min. 1.15 (0.045)
H Piston ring end gap Max. 0.5 (0.02)
K Con-rod small end bore Max. 14.025 (0.5522)
L Crankshaft runout Max. 0.03 (0.001)
M Clutch drum bore Max. 79.5 (3.13)
6 SERVICE INFORMATION SRM-4510, B451

1-6 Special tools

1 2 3 4 5 6

4
30
T-
E
P

e
00 m ug
91 5m a
3 G
P = p
4 Ga
01 ir

4
#. A

/N .
ti on
ni
Ig
7 8 9 10 11 12

13 14 15 16 17

t=1.0 mm

Key Part Number Description Reference

1 91043 Hex T Hande Driver 3 mm Removing and installing hex head bolt
2 91044 Hex T Hande Driver 4 mm Removing and installing hex head bolt
3 G310000050 PET 304 Tachometer Measuring engine speed to adjust Carburetor
4 PET4000EC PET-4000 Spark Checker Checking ignition system
5 91004 Ignition Air Gap Gauge Adjusting pole shoe air gaps
6 91134 Flywheel Puller Removing magneto rotor
7 91018 14mm Pressure Test Plug Testing crankcase and cylinder leakages
8 91147 Compression gauge Measuring cylinder compression
9 91149 Pressure/Vacuum Pump Testing crankcase and crankcase leakages
10 89780330133 Standard Pressure Tester Testing Carburetor and crankcase leakage
11 91041 Pressure rubber plug Plugging exhaust port to test crankcase / cylinder leakages
12 89782616131 Pressure rubber plug Plugging intake port to test crankcase / cylinder leakages
13 89770114732 Bearing tool Removing and installing ball bearings on crankcase
14 89770102830 Bearing Wedge Removing ball bearings on crankshaft
15 363301800310 Washer Installing crankcase oil seal
16 89770230131 Piston pin tool Removing and installing piston pin
17 91101 Piston pin support Removing and installing piston pin