LIST OF APPROVED

PRODUCTS FOR USE IN

PUBLIC WATER SUPPLY IN
THE UNITED KINGDOM
All approved products must be used in accordance with the specific conditions of approval, listed
against the product names in Parts A-E. In addition, the following general conditions of approval
apply to all approved products:
1. That use is in accordance with an Instructions for Use document. Approval holders must
provide drinking water suppliers with copies of the Instructions for Use Document that was
considered by the Drinking Water Inspectorate (DWI) when approval was recommended.
2. That the approval of the Authorities is obtained on condition that there shall be:
• no change in the formulation of the approved product, including change in the source
or identity of raw materials
• no change in the manufacturing process, including location of manufacture
• no change in designation of the approved product
• no change in name or ownership of the organisation holding the approval
3. That the producer shall ensure that the product is tested for conformity with its formulation,
and the source or identity of its raw materials, at such intervals and by such persons, as
may be determined by the Authorities. The results of such testing shall be sent to the
Authorities.
4. If there is suspicion that any of the above is not being followed or has been changed then
notify DWI Regulation 31 team who will investigate ([email protected])
5. That the approval is still valid

Uncontrolled if printed Page 1 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Contents
Part A Chemicals and Filter Media .............................................................................................. 4
A.1 Flocculants and Coagulants............................................................................................ 4
A.1.1 Products based on tannin .......................................................................................... 4
A.1.2 Products based on polyacrylamide.............................................................................. 4
A.1.3 Products based on iron ............................................................................................. 5
A.2 Adsorbents .................................................................................................................. 5
A.3 Ion Exchange Resins Systems........................................................................................ 5
A.3.1 Ion exchange resins.................................................................................................. 5
A.3.2 Ion exchange resin based processes........................................................................... 6
A.5 Disinfection or Cleaning Agents of Membranes.................................................................. 7
A.6 Disinfectants for Emergency Use................................................................................... 11
A.7 Products Based on Traditional Chemicals ....................................................................... 11
A.7.1 Traditional Chemicals.............................................................................................. 11
A.7.2 On-site electrolytic generation of chlorine................................................................... 12
A.7.3 On-site generation of chlorine dioxide........................................................................ 14
A.9 Other Chemicals ......................................................................................................... 14
A.10 Filter Media................................................................................................................ 16
Part B Products for Conveyance of Water ................................................................................. 17
B.1 Pipes ........................................................................................................................ 17
B.1.1 Polyethylene (PE) pipes .......................................................................................... 17
B.1.2 Polyethylene Barrier pipes ....................................................................................... 22
B.1.3 Polyvinylchloride (PVC) pipes................................................................................... 23
B.1.4 Acrylonitrile-butadiene-styrene copolymer (ABS)......................................................... 25
B.1.5 Polyethylene terephthalate (PET).............................................................................. 26
B.1.6 Glass reinforced plastic (GRP) pipes ......................................................................... 26
B.1.7 Cement mortar lined pipes ....................................................................................... 26
B.1.7.1 Cement mortar lined pipes without seal coat........................................................... 26
B.1.7.2 Cement mortar lined pipes with seal coat ............................................................... 28
B.1.8 Pipes coated with factory applied nylon resins ............................................................ 29
B.1.9 Pipes coated with factory applied epoxy resin ............................................................. 29
B.1.10 Stainless steel pipes ............................................................................................... 31
B.1.11 Coated pipes suitable for total immersion in water ....................................................... 35
B.1.12 Pipes coated with a factory applied polyolefin ............................................................. 36
B.2 Well Casings, Screens and Rising Mains ........................................................................ 36
B.3 Products for Conveyance of Water -Emergency Use ........................................................ 38
B.3.1 Hoses ................................................................................................................... 38
B.3.2 Bowsers/tanks ....................................................................................................... 39
B.3.3 Liner bags ............................................................................................................. 39
Part C Lining, Coatings, Sealant and Repair Materials................................................................ 40
C.1 In-situ Installed (tubular) pipe linings .............................................................................. 40
C.2 In-situ applied Pipe Coatings ........................................................................................ 40
C.2.1 Coatings based on epoxy resins ............................................................................... 40

Uncontrolled if printed Page 2 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom
C.2.2 Coatings based on polyurethane............................................................................... 41
C.2.3 Coatings for small diameter pipes ............................................................................. 41
C.3 Site applied coatings for water retaining structures ........................................................... 42
C.3.1 Coatings based on epoxy resins ............................................................................... 42
C.3.2 Coatings based on polyurethane............................................................................... 43
C.4 Flexible covers and linings for water retaining structures ................................................... 44
C.5 Cementitious coatings ................................................................................................. 45
C.6 Sealant & Repair Materials ........................................................................................... 48
Part D Membrane and Filtration Systems................................................................................... 54
D.1 Membrane and Filtration Elements/Systems.................................................................... 54
D.2 Vessels and Containers for Membrane and Filtration Elements .......................................... 59
D.3 Electrodialysis Water Treatment Units ............................................................................ 61
D.4 Filter Media Containing Systems ................................................................................... 61
Part E Other Water Treatment Works Installations ..................................................................... 62
E.1 Tanks........................................................................................................................ 62
E.2 Underdrains ............................................................................................................... 66
E.3 Pressure vessels ........................................................................................................ 68
E.4 Other Products used for the treatment of water................................................................ 69
Index by Product Name ............................................................................................................... 75

Uncontrolled if printed Page 3 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PART A CHEMICALS AND FILTER MEDIA

It is the responsibility of the drinking water suppliers to ensure that
(a) the method and manner of use; and
(b) the purity of these chemicals and products are such that the water treated meets the requirements of the
relevant regulations. Where appropriate, additional specific conditions of approval are listed against the
chemical or product.
Approval holders and water companies should be aware that products or substances that claim to have a
biocidal effect or are used as biocides may require authorisation under the Biocidal Products Regulation.
HSE is the UK competent authority for the Biocidal Products Regulation and so any queries about whether
that legislation applies to a specific product or substance should be addressed to
[email protected]

A.1 Flocculants and Coagulants

A.1.1 Products based on tannin

This section contains no products

A.1.2 Products based on polyacrylamide

For the products listed below the following conditions apply:
(i) no batch must contain more than 0.020% of free acrylamide monomer based on the active polymer
content;
(ii) the dose must average no more than 0.25 mg/l and never exceed 0.50 mg/l of the active polymer;
(iii) an upper limit for the content of free acrylamide monomer must be stated by the supplier for every batch;
and
(iv) the method used for the analysis for free acrylamide monomer is that published in the series “Methods
for the Examination of Waters and Associated Materials” entitled “Determination of Acrylamide Monomer in
Waters and Polymers 1987” (HMSO 1988) Method number 115. ISBN 01175 2039X.

Solenis UK Industries Ltd

Magnafloc LT20 DWI 56/4/885
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use - Magnafloc 22S-DWI, LT20, LT25, LT27.
IFU 001 Issue No.13 Issue Date 02/01/19
Approval expiry date: 13 February 2022
Magnafloc LT22S-DWI DWI 56/4/884
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use - Magnafloc 22S-DWI, LT20, LT25, LT27.
IFU 001 Issue No.13 Issue Date 02/01/19
Approval expiry date: 13 February 2022

Uncontrolled if printed Page 4 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Magnafloc LT25 DWI 56/4/886

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use - Magnafloc 22S-DWI, LT20, LT25, LT27.
IFU 001 Issue No.13 Issue Date 02/01/19
Approval expiry date: 13 February 2022
Magnafloc LT27 DWI 56/4/887
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use - Magnafloc 22S-DWI, LT20, LT25, LT27.
IFU 001 Issue No.13 Issue Date 02/01/19
Approval expiry date: 13 February 2022

A.1.3 Products based on iron

Northern Ireland Water
Sirofloc Magnetite TM M-10 DWI 56/4/1338
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Date: 3.12.2018; Issue No: V001
Concentration of iron leaving the works does not exceed 100µg/l
Approval expiry date: 11 August 2024

A.2 Adsorbents
This section contains no products

A.3 Ion Exchange Resins Systems

A.3.1 Ion exchange resins

Barr + Wray Ltd
Barr + Wray Colour/Organics Removal Ion Exchange Resin BW 141204 DWI 56/4/1238
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Barr + Wray Colour/Organics Removal Ion Exchange Resin
Rev1 - Oct 2016
Approval expiry date: 12 December 2021
Barr + Wray Colour/Organics Removal Ion Exchange Resin BW 200613 DWI 56/4/1239
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Barr + Wray Colour/Organics Removal Ion Exchange Resin
Rev1 - Oct 2016
Approval expiry date: 12 December 2021
Barr + Wray Colour/Organics Removal Ion Exchange Resin BW 341817 DWI 56/4/1237
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Barr + Wray Colour/Organics Removal Ion Exchange Resin
Rev1 - Oct 2016
Approval expiry date: 12 December 2021

Uncontrolled if printed Page 5 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Ixom Operations Pty Ltd

MIEX DOC Resin DWI 56/4/550
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MIEX DOC Resin. Instructions For Use. Version V5. Date of
Issue: 26/08/2015
Approval expiry date: 1 September 2021
MIEX Gold DWI 56/4/1140
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Revision 5, Date of Issue 03 September 2020
Approval expiry date: 18 October 2025

Jacobi Carbons
Resinex KW-H DWI 56/4/1151
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 1-1016-14
Approval expiry date: 18 June 2022

Lanxess Deutschland GmbH

Lewatit S 5128 DWI 56/4/1193
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use (IFU) Lewatit® S 5128,
Issue date: 11/02/2016 Issue No: Version 01
Approval expiry date: 5 March 2022

Purolite International Ltd

Purolite A520E nitrate selective anion exchange resin DWI 56/4/11
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Purolite Instructions for Use for A520E resin for Nitrate removal
from municipal potable water supplies Issue No: 3. Issue Date: March
2017
Approval expiry date: 27 June 2022

A.3.2 Ion exchange resin based processes

Barr + Wray Ltd
Ion exchange colour removal system DWI 56/4/1176
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1 - 17th March 2015
Approval expiry date: 13 September 2021

Ionex SG Ltd
IXL Process DWI 56/4/467
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU: Ionex SG IFU IXL Process (IXN Application), Issue No 6
Approval expiry date: 9 July 2022

Uncontrolled if printed Page 6 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

A.5 Disinfection or Cleaning Agents of Membranes

During the approval process there is no evaluation of a product’s effectiveness, only of its safety in use. An
approval given in this section does not certify that the Authorities are satisfied that that the product is
effective, but only that it is safe for use in accordance with the Instructions for Use supplied.
The fact that a product is approved does not justify any claim about its effectiveness.

Avista Technologies (UK) Ltd

Avista 505 DWI 56/4/1321
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use – Avista 505, Issue date: 11 May 2018
Approval expiry date: 18 February 2024
AvistaClean MF 1000a DWI 56/4/1327
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: AvistaClean MF1000a Instructions for Use
Issue No: 1; Issue date 7 June 2018
Approval expiry date: 16 April 2024
RoCide DB20 DWI 56/4/964
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: RoCide DB20 Instructions for Use, IFU003. Issue 4 Date: 17th
April 2015
Approval expiry date: 17 January 2021
RoClean L403 DWI 56/4/855
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: RoClean L403 Instructions for Use. Issue Reference – 5. Date of
Issue – September 2016
Approval expiry date: 21 November 2021
RoClean P111 DWI 56/4/737
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: RoClean P111 Instruction for Use- Issue 2 – 9 August 2017
Approval expiry date: 15 January 2023
RoClean P303 DWI 56/4/746
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: RoClean P303 – IFU002. Instructions For Use. Issue 2
Approval expiry date: 27 October 2024
Vitec 3000 DWI 56/4/457
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Vitec 3000 Instructions for Use. Issue 4 – 10 August 2017
Approval expiry date: 27 February 2023
Vitec 4000 DWI 56/4/582
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Vitec 4000. Instructions for Use. Date of Issue – 02/04/2018,
Revision Reference - 3
Approval expiry date: 22 October 2023

Uncontrolled if printed Page 7 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Vitec 5000 DWI 56/4/458

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Vitec 5000. Instructions for Use. Issue 4 – 25 October 2017
Approval expiry date: 15 January 2023
Vitec 7000 DWI 56/4/801
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 5, Dated 30 Jan 2015
Approval expiry date: 11 April 2025
Vitec 7000a DWI 56/4/869
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 5, dated 4 May 2015
Approval expiry date: 14 July 2025

Brenntag UK & Ireland

Citric Acid 50% Solution DWI 56/4/1333
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Citric Acid 50% Solution IFU: Issue date 13/09/2018; Version 1
Approval expiry date: 20 November 2023

BWA Water Additives UK Ltd

Flocon 135 DWI 56/4/839
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document: Flocon 135. Issue: 8
Approval expiry date: 8 August 2021

Genesys International Ltd

Genesol 38 DWI 56/4/664
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: DWI-38-IFU/3 Issue date: 01/08/2019
Approval expiry date: 5 October 2024
Genesol 40 DWI 56/4/665
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: DWI-40-IFU/3; Issue Date: 1st August 2019
Approval expiry date: 5 October 2024
Genesol 61 DWI 56/4/1205
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: DWI – 61 – IFU /2, Issue: 2, Date of Issue: 15th Sept 2020
Approval expiry date: 18 November 2025
Genesol 704 DWI 56/4/1319
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Genesol 704 Issue date: 30 April 2018, Issue 1
Approval expiry date: 29 August 2023
Genesys CAS DWI 56/4/1253
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use for Genesys CAS, Jan 17
Approval expiry date: 7 May 2022

Uncontrolled if printed Page 8 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Genesys LF DWI 56/4/495

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Genesys LF. DWI – LF – IFU / 5 8th
October 2018
Approval expiry date: 12 November 2023
Genesys LF60 DWI 56/4/783
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: DWI-LF60-IFU/4 Dated 26/07/2019
Approval expiry date: 5 October 2024
Genesys LS DWI 56/4/781
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: DWI-LS-IFU/4 dated: 26/07/2019
Approval expiry date: 5 October 2024
Genesys SI DWI 56/4/593
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Genesys SI. DWI – SI – IFU/4 Issued 29th
April 2019
Approval expiry date: 23 June 2024
Genesys SW DWI 56/4/524
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Genesys SW. DWI – SW – IFU / 5 8th
October 2018
Approval expiry date: 12 November 2023

Industrial Chemicals Ltd

ICL - Citric Acid Solution DWI 56/4/1342
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: ICL Citric Acid Solution, Issue No.1, 4th December 2018
Only to be used off-line
Approval expiry date: 14 February 2024

Kobell Fluid Technology Ltd

Guardsman GT190 Antiscalant for Membrane Systems DWI 56/4/1123
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Guardsman Anti-scalant Guidance Rev: 20130111
Guardsman GT190 Anti-scalant Dosing Calculations Rev:
20130111
Approval expiry date: 9 April 2024

SUEZ Water Technologies & Solutions

BioMate MBC2881 DWI 56/4/1276
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: BioMate MBC2881 IFU Issue Date: May 2018
Approval expiry date: 2 November 2022

Uncontrolled if printed Page 9 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Hypersperse MDC 704i DWI 56/4/1302

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Hypersperse* MDC 704i IFU. Issue No: Version 2; Issue date:
December 2017
Approval expiry date: 22 January 2023
Hypersperse MDC 711 DWI 56/4/1300
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Hypersperse* MDC711 IFU (Instruction for Use)
Issue date: December 2017; Issue number: Version 2
Approval expiry date: 21 June 2023
Hypersperse MDC 714 DWI 56/4/1301
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Hypersperse* MDC714 IFU
Issue date: December 2017; Issue number: Version 2
Approval expiry date: 20 December 2022
Hypersperse MSI310 DWI 56/4/1311
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Hypersperse MSI310 IFU Issue: December 2018, Version 2
Approval expiry date: 25 June 2023
KLEEN MCT515E DWI 56/4/1273
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Kleen MCT515E Version 2 May 2018
Approval expiry date: 29 August 2022
Kleen MTC405 DWI 56/4/1289
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Kleen MTC405 IFU Version 2 January 2018
Approval expiry date: 17 September 2023
Kleen* MCT103 DWI 56/4/1008
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Kleen MCT103. Version 2: May 2018
Approval expiry date: 29 August 2022
Kleen* MCT524 DWI 56/4/1007
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Kleen* MCT524. IFU Version 2 : May 2018
Approval expiry date: 29 August 2022
Kleen* MCT882 DWI 56/4/1010
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Kleen* MCT882. Version 2 May 2018
Approval expiry date: 29 August 2022

Uncontrolled if printed Page 10 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Water Treatment Products Limited

WTP RO 411 DWI 56/4/821
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Water Treatment Products Ltd WTP RO411
reverse osmosis antiscalant. Issue 3. Dated: 15 January 2020
Approval expiry date: 5 July 2025
WTP RO 413 DWI 56/4/822
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use: Water Treatment Products Ltd WTP RO 413
reverse osmosis antiscalant. Issue 3 Dated 15 January 2020
Approval expiry date: 5 July 2025

A.6 Disinfectants for Emergency Use

Disinfectants for emergency use are no longer approved and listed under the requirements of relevant
regulations. Guidance upon the choice and use of disinfectants in an emergency is provided in Advice Sheet
9 (http://www.dwi.gov.uk/drinking-water-products/advice-and-approval/Advicesheet9.pdf).
Approvals of previously listed disinfectants for emergency use have been revoked – see Information Letter
08/2008 (http://www.dwi.gov.uk/stakeholders/information-letters/2008/08_2008.pdf )

This section contains no products

A.7 Products Based on Traditional Chemicals

A.7.1 Traditional Chemicals

The following traditional chemicals (not currently covered by a specific appropriate BS EN) are considered by
DWI to meet the requirements of the relevant regulations subject to the following condition:
The method of use and the purity of these products shall be such that, when used in the treatment of water
intended for human consumption, the water so treated shall meet the appropriate requirements of the Water
Supply (Water Quality) Regulations. See Reg 31 letter on the "Review of arrangements for approval of
Traditional Chemicals" issued 6 August 2018 (http://www.dwi.gov.uk/drinking-water-
products/faqs/Reg31Let_060818.pdf)

Traditional Chemical
Citric acid (food grade) DWI 56/1/106
Conditions of Approval:
For use only in cleaning of membranes
Magnesium sulphate DWI 56/1/106
Use only for re-mineralisation with RO membrane systems

Uncontrolled if printed Page 11 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

A.7.2 On-site electrolytic generation of chlorine

Products in this section are not fully covered by EN 901 (sodium hypochlorite) and must conform to the
following conditions of use:
(i) the method of use and the purity of the output of these products shall be such that, in the case of water for
public supply, the water so treated meets the requirements of the relevant Regulations; and
(ii) the treated water must not contain more than 700 µg/l chlorate.

Danish Clean Water A/S

Sodium Hypochlorite generated by Neuthox DWI 56/4/1298
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: T00 ECA-Generators Machine: Series 02; Dated: 28-11-2017
(i) the method of use and the purity of the output shall be such that, in
the case of water supply, the water so treated meets the requirements
of the relevant regulations; and (ii) the water treated must not contain
more than 700μg/l chlorate
Approval expiry date: 19 December 2022
Sodium Hypochlorite generated by Neuthox T10/15 DWI 56/4/1315
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: T10 ECA-Generators
Machine: Series 02; Dated: 20-01-2018
(i) the method of use and the purity of the output shall be such that, in
the case of water supply, the water so treated meets the requirements
of the relevant regulations; and (ii) the water treated must not contain
more than 700μg/l chlorate
Approval expiry date: 29 July 2023
Sodium Hypochlorite generated by Neuthox T20 DWI 56/4/1318
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: T20 ECA-Generators
Machine: Series 00012; Dated: 15-02-2018
(i) the method of use and the purity of the output shall be such that, in
the case of water supply, the water so treated meets the requirements
of the relevant regulations; and (ii) the water treated must not contain
more than 700μg/l chlorate
Approval expiry date: 26 July 2023

De Nora Water Technologies UK Services Ltd

Clortec cell DWI 56/4/549
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Revision 3.3; 25 September 2019
Approval expiry date: 15 June 2025

Evoqua Water Technologies Ltd

Wallace and Tiernan OSEC ® DWI 56/4/775
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Wallace & Tiernan® Instruction Manual OSEC®
Approval expiry date: 24 July 2022

Uncontrolled if printed Page 12 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Gaffey Technical Services Ltd

Sodium Hypochlorite generated by Hyprolyser Electrochlorination System DWI 56/4/1341
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Hyprolyser 280, 560, 110, 2200 Electrolysis system for on-site
hypochlorite generation. IFU Issue Date: Nov 2018; Issue No.
IFUv1.1
(i) the method of use and the purity of the output of these products
shall be such that, in the case of water for pulic supply, the water so
treated meets the requirements of the relevant Regulations; and (ii)
the treated water must not contain more than 700 µg/l chlorate.
Approval expiry date: 20 February 2024

Grundfos Holdings A/S

Sodium Hypochorite generated by Selcoperm DWI 56/4/864
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU v003
Approval expiry date: 23 March 2021

Lutz-Jesco GmbH
Easychlorgen 280 – 2200 Electrolysis system for on-site hypochlorite
generation DWI 56/4/1369
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Easychlorgen 280 – 2200 Electrolysis system for on-site
hypochlorite generation - IFUv1.1 Issued: 11/2018
(i) the method of use and the purity of the output of these products
shall be such that, in the case of water for public supply, the water so
treated meets the requirements of the relevant Regulations; and (ii)
the treated water must not contain more than 700 μg/l chlorate.
Approval expiry date: 20 February 2024

Uncontrolled if printed Page 13 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

A.7.3 On-site generation of chlorine dioxide

Products in this section are not fully covered by EN 12671 (chlorine dioxide). The following products must
conform to the following conditions of use:
(i) the method of use and the purity of the output of these products shall be such that, in the case of water for
public supply, the water so treated meets the requirements of the relevant Regulations; and
(ii) the combined concentration of chlorine dioxide, chlorite and chlorate shall not exceed 0.5 mg/l as chlorine
dioxide in the water entering supply.

Grundfos Holdings A/S

Oxiperm ISIA (with U-type reactor) DWI 56/4/1236
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Version 1, 2016
Approval expiry date: 30 November 2021

International Water Solutions Ltd

Chlorine Dioxide generated by Xziox DWI 56/4/998
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1.8 Dated 27/01/16
Approval expiry date: 30 January 2026

A.9 Other Chemicals

Airedale Chemical Company Ltd
Airophos 750PWG DWI 56/4/960
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 3 dated 23/1/14
Approval expiry date: 19 March 2025

Aqua Smart Inc.

SEAQUEST DWI 56/4/202
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Seaquest V1
Approval expiry date: 23 October 2025

Arch Chemicals Ltd

Constant Chlor Plus Briquettes DWI 56/4/1241
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use – Constant Chlor Plus Briquettes. Issue no:
1.1. Issue date: 30 Sept 2016
Approval expiry date: 12 December 2021

B&V Water treatment

Ultralox 40 DWI 56/4/1074
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Ultralox 40 Official Instructions for Use, Issue 3, March 2015
Approval expiry date: 29 November 2023

Uncontrolled if printed Page 14 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

BioBullets Ltd
Silver Bullets 1000 DWI 56/4/852
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use document for Silver Bullets 1000. Issue No 2.
Dated 5th October 2017
This product can only be used for raw water treatment.
Approval expiry date: 20 December 2022
Silver Bullets 2000 DWI 56/4/1000
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use for Silver Bullets 2000, Issue No: 2 Issue
Date 5th October 2017
This product can only be used for raw water treatment.
Approval expiry date: 16 July 2023

Brenntag UK & Ireland

Magnesium Sulphate Heptahydrate 40% DWI 56/4/1334
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Magnesium Sulphate Heptahydrate 40%:- Instructions for Use
Issue Date: 27/09/2018: Issue No: Version 1
Approval expiry date: 20 June 2024
TP Chlor DWI 56/4/979
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 3 dated 19/6/15
The method of use and purity of this product shall be such that in the
case of water for public supply the water so treated meets the
requirements of the relevant regulations.
Approval expiry date: 21 October 2025
TP Chlor plus DWI 56/4/1190
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 3 dated 19/6/15
The method of use and purity of this product shall be such that in the
case of water for public supply the water so treated meets the
requirements of the relevant regulations.
Approval expiry date: 21 October 2025

Clinty Chemicals Limited

Purafloc TM 001 DWI 56/4/1378
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Purafloc TM 001 Issue Date: 12th August 2019; Issue No:1
Approval expiry date: 18 August 2024

Uncontrolled if printed Page 15 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Industrial Chemicals Ltd

Thycal DWI 56/4/1025
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use :THYCAL. Issue No: Version 2. Issue Date:
14th June 2016
Approval expiry date: 1 September 2021

JFI Limited
Purafloc TM 001 DWI 56/4/1355
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Purafloc TM 001 Issue Date: 12/02/19; Issue No 1.0
Approval expiry date: 10 June 2024

Lhoist UK Ltd
Akdolit® SLS45 DWI 56/4/1392
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Akdolit® SLS45 IFU Issue Date: 17/04/2020; Version 1.1
Approval expiry date: 14 June 2025

Tarmac Cement and Lime Limited

Puresol DWI 56/4/1147
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Puresol for pH Control and Water Softening in Drinking Water
Processes
Issue 001, Issue Date: 21st Oct 2019
Approval expiry date: 9 October 2024

Tarmac Lime & Cement

Kalic HSD DWI 56/4/1206
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Kalic HSD for pH Control and water softening in Drinking water
treatment processes. Issue 002 05/04/2016
Approval expiry date: 27 April 2025

A.10 Filter Media

Dryden Aqua Ltd
AFM Activated Filter Media DWI 56/4/382
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: AFM Activated Filter media. 6th November 2014. Issue no 2
Approval expiry date: 20 February 2025

Uncontrolled if printed Page 16 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PART B PRODUCTS FOR CONVEYANCE OF WATER

B.1 Pipes

B.1.1 Polyethylene (PE) pipes

Asset International Ltd
Weholite Pipe and Panels DWI 56/4/513a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Weholite HDPE Pipes - Issue 5 September 2018
Approval expiry date: 2 February 2024

Centraltubi SPA
Safe 10 DWI 56/4/1366
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Safe 10 - Manual of Use - 2nd Revision Jan 2017
Approval expiry date: 23 July 2024

Cork Plastics
CP Polytec 100 DWI 56/4/1351
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE OF CP POLYTEC 100 EXTERNAL
BLUE & INTERNAL BLACK PE100 POLYETHYLENE PIPE FOR
SUPPLY OF DRINKING WATER UNDER PRESSURE Issue No.1
Date: October 2018
Approval expiry date: 19 March 2025
CP Polytec PE80E DWI 56/4/1187
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU CP Polytec PE80E 3doc Dec15
Approval expiry date: 1 June 2021

EBERO Pipe Systems Ltd

Gerothern PE100 Polyethylene Pipes DWI 56/4/1115
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Document No. 065 Revision 2 Dated: 25.05.2019
Approval expiry date: 22 September 2024

Egeplast International GmbH

egeclean (+) DWI 56/4/1157
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use. egeclean plus pipes . Issue 1 dated
03/07/2014
Approval expiry date: 31 October 2023

Uncontrolled if printed Page 17 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

egeclean 9010 DWI 56/4/1158

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use. egeclean PE100/egeclean 9010. Issue 1
dated 14 February 2018
Approval expiry date: 19 April 2023
egeclean PE100 DWI 56/4/1156
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use. egeclean PE100/egeclean 9010. Rev No 3
Date: 30 January 2019
Approval expiry date: 12 October 2024
egelen PE 100 Blue DWI 56/4/436
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PE-HD PE100 in black and blue Version 11 dated 30th January
2019
Approval expiry date: 12 October 2024
egelen PE100 Black DWI 56/4/436
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PE-HD PE100 in black and blue Version 11 dated 30th January
2019
Approval expiry date: 12 October 2024
egeplast 9010 DWI 56/4/1065
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU_egelen_9010_Drinkwater Rev11
Version 11 dated 30th January 2019
PE grades as specified to approval holder and Cold potable water
applications only.
Approval expiry date: 19 April 2023
egeplast egelen (+) Plus Pipe DWI 56/4/1111
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use Peelable layer pipes. IFU-UK Rev 11 5th July
2018
Approval restricted to a single grade of Polyethylene (Eltex TUB
125N3000)
Approval expiry date: 31 October 2023

George Fischer Sales Ltd

GF PE100 Black Pipe DWI 56/4/957
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 15/HLET 15920/15. Dated 23 January 2015
Approval expiry date: 29 March 2025

Gerodur MPM Kunststoffverarbeitung GmbH & Co. KG

GEROthen® COEX DWI 56/4/1370
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Gerodur, GEROthen® Pipes - products and design No 01 Issue
No: 01; Issue Date: 13.08.2019
Approval expiry date: 2 April 2025

Uncontrolled if printed Page 18 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

GPS
Excel White DWI 56/4/1269
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: EXCEL WHITE POLYETHYLENE PIPES MADE FROM WHITE
AND BLACK PE100 MATERIAL
Issue Number 1; Issue Date: 21/03/2017
Approval expiry date: 31 May 2023
GPS B Light Blue Polyethylene Pipe DWI 56/4/242
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue: Instructions for Use . Issue No: 3. Issue Date: 16 Jan
2017
Approval expiry date: 10 June 2022
GPS Excel (Black) DWI 56/4/851
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue No. 2
Approval expiry date: 6 November 2021
GPS Excel (Blue) DWI 56/4/850
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue Number 2
Approval expiry date: 6 November 2021
GPS Excel (Black) Type F DWI 56/4/961
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Excel. Issue No: 6. Issue Date: 16/3/2015
Approval expiry date: 1 September 2021
GPS Excel 3c (Black) DWI 56/4/871
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Excel 3 c PE Pipe Coils Made From Blue PE100 Or Black PE100
Materials. Issue No. 4. Dated: 14.6.2013
Approval expiry date: 1 September 2021
GPS Excel 3c (Blue) DWI 56/4/853
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Excel 3 c PE Pipe Coils Made From Blue PE100 Or Black PE100
Materials. Issue No. 4. Dated: 14.6.2013
Approval expiry date: 1 September 2021
GPS Excel CR DWI 56/4/946
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: 2 Issue Date: 16/3/2015
Approval expiry date: 1 September 2021
GPS Excel NB DWI 56/4/1026
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue: Excel NB. Issue No: 1. Issue Date: 1/7/2011
Approval expiry date: 1 September 2021

Uncontrolled if printed Page 19 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

GPS Excel NB Type V DWI 56/4/1050

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU, Issue Number 3, 24/05/2017
Approval expiry date: 6 September 2022
GPS N Black Polyethylene Pipe DWI 56/4/1260
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU, Issue Number 1, dated 7/2/2017
Approval expiry date: 22 May 2022
GPS N Blue PE80 Pipe DWI 56/4/651
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue date 26/4/19 Issue no 3
Approval expiry date: 14 September 2024

Idrotherm 2000 spa

RENO 100 DWI 56/4/1168
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use Issue: PFSSP Rev 3, Issue Date: 22/10/2019
Approval expiry date: 5 May 2025

Peak Pipe Systems

Peak Pipe Systems DWI 56/4/548
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PSIFU01– Issue 09 Dated: 03/03/2020
Approval expiry date: 20 May 2025

Pipelife Ireland Limited

Qual-plast HDPE Pipe DWI 56/4/997
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Qual-PLAST PE Pipe Systems Instructions for Use. Date of
Issue: 27.09.10. Issue number: 2
Approval expiry date: 21 August 2021
Qual-plast MDPE Pipe DWI 56/4/240
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Qual-PLAST MDPE pipe systems - Instructions for Use. Issue
No: 2. Issue date: 16/01/17
Approval expiry date: 24 July 2022
QualPLAST Polyethylene MDPE co-extruded pipe DWI 56/4/1282
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU 01 2017
Approval expiry date: 23 August 2022

Uncontrolled if printed Page 20 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Polypipe Building Products

Black PE80 Polyethylene Pipes DWI 56/4/968
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document for Polypipe Building products’
PE80 Black polyethylene Pressure pipes to BS EN 12201-2 made
from Ineos Eltex Tub 171 Black Polyethylene Compound Doc
Reference: PS 157. Issue No: 02 Date: 29 May 2020
Suitable for use above ground only.
Approval expiry date: 29 July 2025
Black PE80 Polyethylene Pipes (ME3440) DWI 56/4/986
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue 1, 7 July 2016
Approval expiry date: 30 November 2021
Blue PE80 Polyethylene Pipes DWI 56/4/970
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PSNR001 issue 2 dated 29/05/2020
Approval expiry date: 29 June 2025
Blue PE80 Polyethylene Pipes (PC002 50R698) DWI 56/4/1120
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PS 161 Issue 1 26 September 2013
Approval expiry date: 17 October 2023
Polypipe Blue PE100 Polyethylene Pipes (TUB124N 2025) DWI 56/4/1296
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use document for Polypipe Building Products' PE
100 Blue Polyethylene pressure pipes to BS EN 12201-2 made from
Etex TUB124N 2025 polyethylene compound. Issue Number: 01;
Issue date: 28 Sept 2017
Approval expiry date: 15 March 2023

Polypipe Ltd
Polypipe Black PE100 Polyethylene Pipes (TUB121N3000) DWI 56/4/1343
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR POLYPIPE
BUILDING PRODUCTS’ PE 100 BLACK POLYETHYLENE
PRESSURE PIPES TO BS EN 12201-2 MADE FROM ELTEX
TUB121N 3000 POLYETHYLENE COMPOUND - Version: 01 Issued:
7 December 2018
Pipes for above ground use only
Approval expiry date: 6 February 2024

Radius Subterra – a part of RadiusPlus Ltd

Subcoil DWI 56/4/461
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 6.
Approval expiry date: 1 October 2025

Uncontrolled if printed Page 21 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Radius Systems Ltd

High Performance SC100 Dark Blue Pipe PE100 pipe including Clean Pipe DWI 56/4/939
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: High Performance SC100 Dark Blue PE100 pipe including Clean
Pipe, Issue No’ 4: Jan 2016
Approval expiry date: 11 July 2022
PE100 High Performance Profuse Pipe including Factory Sealed DWI 56/4/943
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PE100 High Performance Profuse Pipe including Clean Pipe,
Issue No’ 3: Jan 2016
Approval expiry date: 11 July 2022
SC100 (PE100) XL large diameter / heavy wall dark blue potable water pipe DWI 56/4/1146
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No 01, dated 02/09/2015
Approval expiry date: 8 September 2025
SC80 Service Pipe DWI 56/4/941
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SC 80 Service Pipe. Issue No 02, dated 23/01/2015
Approval expiry date: 3 February 2025

Simona UK Ltd
Simona PE100 Pressure Pipe Black DWI 56/4/875
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Simona ® PE100 Pressure pipes manufactured using either
Hostalen CPR100Black/Blue or Eltex tub 121 N3000. Issue number
11/14. Dated November 2014
Approval expiry date: 4 December 2024

B.1.2 Polyethylene Barrier pipes

Egeplast International GmbH
Egeplast SLA Barrier Pipes DWI 56/4/1109
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU – UK. Rev.-Nr.: 11. 17th July 2020
Approval expiry date: 20 August 2025

GPS
GPS Protecta-Line DWI 56/4/872
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 8. Dated 26 April 2019
Approval expiry date: 23 November 2024
GPS Protecta-Line 3c DWI 56/4/873
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue 8. 26 April 2019
Approval expiry date: 23 November 2024

Uncontrolled if printed Page 22 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Polypipe Building Products

Polyguard: Polyethylene/Aluminium/Polyethylene barrier pipes DWI 56/4/857
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use Document For Polypipe Building Products'
Polyguard PE/Al/PE Pressure Pipe to WIS 4-32-19 Made From Ineos
Eltex PC-002-50 R568 Blue Polyethylene/Novelis Aluminium.
Document Reference: PSNR003. Issue No. 2. Dated 29/05/2020
Approval expiry date: 20 September 2025
Polyguard: Polyethylene/Aluminium/Polyethylene barrier pipes (ME3444) DWI 56/4/1076
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use document. Document reference :PS160.
Issue no: 1. Date: 28 September 2012
Approval expiry date: 21 January 2023

Radius Systems Ltd

Puriton Pipe DWI 56/4/1112
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Purition Barrier Pipe. Issue 4 dated 04/11/2016
Approval expiry date: 29 October 2024

B.1.3 Polyvinylchloride (PVC) pipes

Please note that all approved PVC pipes are made with non-lead stabilisers.

Adequa WS S.L.U
Uratop PVC-O Adequa DWI 56/4/1266
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: URATOP PVC-O ADEQUA
Issue Date: May 2017; Issue No.: Version 2
Approval expiry date: 19 June 2023

Durapipe UK
Durapipe Grey PVC-U Pipe NGS DWI 56/4/937
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Date of Issue: 03/05/16. Issue Number: 1
Approval expiry date: 4 October 2021
Durapipe PREMIUM PVC-U pipe DWI 56/4/1226
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Durapipe PREMIUM PVC-U Pipes Issue Date: 03/05/2016, Issue
No: 1
Approval expiry date: 5 October 2021

Uncontrolled if printed Page 23 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Dyka B.V.
Dyka Grey PVC-U Pipe NGS DWI 56/4/637
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Dyka - PVC-u Technical Specification. Date of Issue 17/11/2006.
Issue Number 1.
Approval expiry date: 4 October 2021

Dyka S.A.S.
Bi-OROC DWI 56/4/1207
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Bl-OROC PN16 PVC-O Technical Specifications Dated:
14/05/2018; lssue Number: V0
Approval expiry date: 13 October 2021

George Fischer Sales Ltd

GF DEKADUR PVC-U pressure pipe DWI 56/4/1231
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No 2, 13 June 2016
Approval expiry date: 26 April 2022
GF PVC-U Inch Pipe DWI 56/4/1235
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No. 1, 27 July 2016
Approval expiry date: 31 January 2023

Molecor Tecnología SL
TOM PVC-O Pipe DWI 56/4/1057
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: TOM PVC Orientated Pipe (PVC-O) Information for Use
Document. Edition: 1 January-14/ Revision 1
Approval expiry date: 12 June 2024

Wavin Ireland Ltd

Aquaforce (with non-lead stabiliser) DWI 56/4/600
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Wavin Aquaforce Instructions for Use. Issue number 04 April
2004
Approval expiry date: 13 February 2022

Uncontrolled if printed Page 24 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.4 Acrylonitrile-butadiene-styrene copolymer (ABS)

Durapipe UK
Durapipe ABS Pipe Type S DWI 56/4/660
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: ABS Pipes And Fittings Made From Durapipe ABS Type S,
GRET ABS Material Issue 7 Date 24/6/2011
Approval expiry date: 8 August 2021

George Fischer Sales Ltd

GF ABS pressure pipe DWI 56/4/753
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use (IFU) - GF ABS Pressure Pipe, Issue date:08
January 2015; Issue No:1
Approval expiry date: 29 January 2025

Uncontrolled if printed Page 25 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.5 Polyethylene terephthalate (PET)

This section contains no products

B.1.6 Glass reinforced plastic (GRP) pipes

Future Pipe Industries B.V
Wavistrong Series DWI 56/4/656
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Wavistrong Glassfibre Reinforced Epoxy
(GRE) Pipe Systems. Issue No: IFU DW FPI BV Version no: 2. Date
of Issue 22/2/2011
Approval expiry date: 26 February 2022

B.1.7 Cement mortar lined pipes

For Products in this section, the following conditions applies:
Before connection to the supply, the water undertaker or their appointed agent, must carry out tests to
establish that migration from the cement mortar lining will not cause a contravention of the upper prescribed
concentration for hydrogen ion in the relevant Regulations.

B.1.7.1 Cement mortar lined pipes without seal coat

Electrosteel Castings Ltd

Electrofresh Ductile Iron Pipe DWI 56/4/992
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use for Electrofresh Pipes at Site
Work Instruction: WC-04-02
Issue No: 03 Rev. C Issue Date: 25.02.2016
Before connection to supply, the water undertaker or their approved
agent, must carry out tests to establish that migration from the cement
mortar lining will not cause a contravention of the upper prescribed
concentration for hydrogen ion in the relevant regulations.
Approval expiry date: 1 August 2021

Erciyas Celik Boru Sanayi A.S

Erciyas Steel Water Pipe – Cement Lined DWI 56/4/1047
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction For Use. Erciyas Pipeline Systems Steel Water Pipes
lined with CEMENT. Document number: TA-04-13, Revision: 2. Date
of Issue: 1/02/12
Approval expiry date: 11 December 2021

Uncontrolled if printed Page 26 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

JINDAL SAW GULF LLC

JSGL-JAL-1A DWI 56/4/1122
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for use document (JSAW-JAL-1A) Ductile iron pipes
to convey raw water, water during treatment, treated and potable
water with or without pressure’ Issue No.: 1 Issue Date: 15/09/2013
Approval expiry date: 20 February 2025

Jindal Saw Ltd

JSAW-JAL-11A DWI 56/4/935
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document JSAW-IFU-DI-DWI-OPC-SC-001
Rev. 02, 15/11/16
Approval expiry date: 12 March 2022
JSAW-JAL-1A DWI 56/4/933
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document, JSAW-IFU-DI-DWI-OPC-001
Rev. 02, 15/11/16
Approval expiry date: 12 March 2022

Saint-Gobain PAM UK Ltd

System CL DWI 56/4/283
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SAINT GOBAIN PAM UK. Instructions for Use Document for
System CL Pipes. Issue Number 9. Date: 25th May 2009
Approval expiry date: 5 May 2023

Stanton Bonna Concrete Limited

Stanton Bonna Concrete Pressure Pipe DWI 56/4/1375
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Version 1 Dated 22/07/2019
Approval expiry date: 10 September 2024

Superior Pipeline Products Ltd

System Cement Mortar Lined Ductile Iron Pipe DWI 56/4/990
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use System Cement Mortar lined Ductile Iron
Pipe Issue no: 4 March 2017
Approval expiry date: 8 November 2022

European Pipeline Group

European Pipeline Group Svobodny Sokol Ductile Iron Pipe DWI 56/4/1114
Use of the product must be in accordance with the Instructions for
Use: Edition 2 dated 1/7/2013
Approval expiry date: 15 August 2023

Uncontrolled if printed Page 27 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.7.2 Cement mortar lined pipes with seal coat

Electrosteel Castings Ltd

Electrofresh Plus Pipes DWI 56/4/537
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU (instructions for use) for Electrofresh plus pipes at site .
Issue No: 04 Rev: 0 Issue Date 01.04.2017
Approval expiry date: 2 August 2021

Jindal Saw Ltd

JSAW-JAL-11B DWI 56/4/936
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document JSAW-IFU--DI-DWI-BFSC-SC-
001 Rev. 02, 15/11/16
Approval expiry date: 12 March 2022
JSAW-JAL-1B DWI 56/4/934
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document JSAW-IFU-DI-DWI-OPC-SC-001
Rev. 02, 15/11/16
Approval expiry date: 12 February 2022

Saint-Gobain PAM UK Ltd

System XL DWI 56/4/1317
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SAINT GOBAIN PAM UK. Instructions for Use Document for
System XL. Issue number 8. Dated: 1st January 2013
Approval expiry date: 5 May 2023

Uncontrolled if printed Page 28 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.8 Pipes coated with factory applied nylon resins

Leyfos Plastics Limited
Rilsan Nylon Green Coated Pipes and Fittings DWI 56/4/615
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Creation Date: 1/10/13 Document number: LEYDWI01.. Issue
Number 02
Approval expiry date: 26 November 2023

B.1.9 Pipes coated with factory applied epoxy resin

BAIKA Steel Tubular Systems SL
Steel pipe coated with Eurokote 468 Thixo DWI 56/4/1203
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Eurokote 468 Thixo, Issue No2 - 21 March 2019
Approval expiry date: 2 March 2021

BSR Pipeline Services Ltd

BSR/EPW/004 - Copon Hycote PWX DWI 56/4/772
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue 8 Nov 2010
Approval expiry date: 6 April 2022

Erciyas Celik Boru Sanayi A.S

Steel Water Pipes line with epoxy coating Eurokote 468 Thixo DWI 56/4/1001
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Date of Issue: 05.07.18TA-04-30 Revision 1
Approval expiry date: 4 September 2024

Freeflow Pipesystems Ltd

Pipes Lined with Resicoat R4-FB HKC71R DWI 56/4/817
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 8 Dated 17.02.20
Approval expiry date: 4 May 2025

Noksel Steel Pipe Co Inc

Noksel Steel Water Pipe – Coated with Thixo 468 DWI 56/4/1192
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: NOK-DJM-INT-0001 18/08/2020, Issue 1
Approval expiry date: 4 October 2025

Uncontrolled if printed Page 29 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Northpoint Ltd
Pipes and fittings lined with Eurokote 468 Thixo DWI 56/4/1209
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions of Use of pipes lined with Eurokote 468 Thixo
Coating System. Issue No 2 26/1/16
Approval expiry date: 13 June 2021
Pipes and Fittings lined with Jotaguard VA 5001 DWI 56/4/1304
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: J-Guard VA 5001 IFU 201711101343.00 Issue Date: 2017-11-
10; Issue number: 00
Approval expiry date: 3 December 2022
Pipes, Fittings and Steelwork coated with Resicoat R4-FB HKC71R DWI 56/4/659
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU.RESICOTE R4-FB.201911010915 08 Issued 14-08-2019
Approval expiry date: 17 November 2024

Orrmac Coatings Limited

Pipes and Fittings lined with Resicoat R4-FB HKC71R DWI 56/4/771
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue no 5 dated April 2015
Approval expiry date: 31 May 2025
Pipes lined with Scotchkote 162PWX DWI 56/4/985
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU, Issue 8, Nov 2010
Approval expiry date: 5 March 2022

Saint-Gobain PAM UK Ltd

PaM Natural Pipeline Components DWI 56/4/618
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Number 6. Dated 19th November 2019
Approval expiry date: 20 February 2025

UTS Engineering Ltd

Fabricated mild steel pipework coated with Jotaguard VA5001 DWI 56/4/1324
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Pipes coated with Jotaguard VA5001 IFU Issue Date 1st
February 2019; Issue No: 1.
Approval expiry date: 11 June 2024
Fabricated mild steel pipework coated with Scotchkote 162pwx DWI 56/4/1085
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Pipes lined with Scotchkote 162 PWX Instructions for use
Document. Issue 1. Date 5th March 2013
Approval expiry date: 26 April 2023

Uncontrolled if printed Page 30 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.10 Stainless steel pipes

ABC Stainless Steel Ltd
Q Pipe System DWI 56/4/542a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use : 1. Stainless Steel “Q” pipe system . 2.
Stainless steel storage, Process Tanks and Vessels . Issue no: 2
Date: 20th October 2003
Approval expiry date: 4 January 2023

AJ Engineering and Construction Services Ltd

Stainless Steel Pipework and Fabrications DWI 56/4/1220a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Stainless Steel Pipework and Fabrications for water use. Issue
No: WP 41, Issue date: 04/08/2016
Approval expiry date: 19 September 2021

Alpha Plus Ltd

Stainless Steel Pipework DWI 56/4/692
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No. 2 Issue Date 13-09-19 (Document ref: IFU-02)
Approval expiry date: 9 October 2024

Amari Metals Ltd

Stainless Steel Tube, Stainless Steel pipe DWI 56/4/738
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU/DWI/Amari/TP: Issue No 3
Approval expiry date: 19 July 2021

Berry & Escott Engineering

Stainless Steel Pipework and Fabrications DWI 56/4/1362
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU - Stainless Steel Frabricated Pipework
Approval expiry date: 1 May 2024

Blackburns Metal Ltd

Stainless Steel ANSI Metric ISO Pipe, Stainless Steel ANSI Metric ISO Tube,
Stainless Steel ANSI Metric ISO Fittings DWI 56/4/1224
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Number 1, Issue date 26th May 2016
Approval expiry date: 26 June 2021

Uncontrolled if printed Page 31 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Bridges Electrical Engineering Ltd

Bridges in-house fabricated stainless steel pipe spools and products DWI 56/4/1268a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Bridges in-house fabricated stainless steel pipe spools and
products , Issue 1 22/03/17
Approval expiry date: 14 May 2022

BSS Industrial
Stainless Steel Tubings and Fittings DWI 56/4/1017
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: BSS_Industrial_IFU_24.04.17v1
Approval expiry date: 4 June 2022

DH Stainless Ltd
Stainless Steel Metric ISO & ANSI welded pipe and fittings DWI 56/4/773
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1 dated 13 March 2020
Approval expiry date: 13 May 2025

Dustacco Engineering Ltd

DE Stainless Steel Systems DWI 56/4/647
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: F011 (Issue date 12/8/13) in accordance with BSSA Code of
Practice
Approval expiry date: 15 August 2024

Equipdata Trading
IPSSSPW01 Stainless Steel Pipework and Fabrications DWI 56/4/1316
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use of IPS Product Number IPSSSPW01 – Issue
4; Dated 06/03/2018
Approval expiry date: 10 March 2023

Filtec Water Services Ltd

Filtec "Selkie" Stainless Steel Products DWI 56/4/1396a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: HANDLING, INSTALLATION AND COMMISSIONING
INSTRUCTIONS FOR THE FILTEC SELKIE RANGE OF
STAINLESS-STEEL PRODUCTS FOR USE IN CONTACT WITH
TREATED OR PARTIALLY TREATED POTABLE WATER
Dated: 29/04/2020; Issue No: 01; Rev 02

Approval expiry date: 17 May 2025

Uncontrolled if printed Page 32 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

George Green (Keighley) Ltd

Stainless Steel Pipework & Fittings - Flanged/Screwed - All diameters &
Grades DWI 56/4/699
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No 4. Date 3 May 2019
Approval expiry date: 16 September 2024

Homer Burgess Ltd

Tanks and associated Pipework, Weir Plates and Baffle Plates manufactured
from Stainless steel suitable for use with drinking water DWI 56/4/1107a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Title: Homer Burgess Ltd., Manufacturer’s official use instructions
for Stainless Steel Products in contact with Drinking Water.. Issue
Number Rev: 1 26/01/2016
Approval expiry date: 22 May 2023

Neumo UK Ltd
Neumo Stainless Steel Tube and Fittings DWI 56/4/1167
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1: 27/11/2019
Approval expiry date: 29 March 2025

Ocean Kinetics Ltd

Unlined 316 & 316L Stainless Steel Tanks and Pipework DWI 56/4/1395a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: OK-IFU-2020-001 Rev 1; Issue date: 16/04/20
Approval expiry date: 22 April 2025

OSTP
OSTP Stainless Steel pipe and fittings of 12mm bore or greater. DWI 56/4/516
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Drinking Water Supply – Stainless steel welded tubular products
IFU Issue 1 Issue Date: 06/08/2019
Approval expiry date: 10 October 2024

Powerrun Pipe-Mech Ltd

Powerrun fabricated stainless steel pipework DWI 56/4/769
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PFSSP Rev 3 dated 22/10/2019
Approval expiry date: 27 January 2025

Righton and Blackburns Ltd

Stainless Steel Pipe | Stainless Steel Tube | Stainless Steel Fittings | Material
grades 304/304L, 316/316L, 1.4301/1.4307, 1.4401/1.4404 DWI 56/4/1221
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU - RB-QA-LS-IFU-DW - Issue 02 17-05-2019
Approval expiry date: 22 June 2021

Uncontrolled if printed Page 33 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Stainless Steel pipes, Stainless Steel Tube, Stainless Steel Fittings DWI 56/4/1221
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Number 1, Issue date 26th May 2016
Approval expiry date: 22 June 2021

Ross-shire Engineering Ltd

Stainless steel process pipework systems DWI 56/4/1034
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue: Information for Use Drinking Water Stainless Steel
Process Pipework Systems. Issue No: 2 Issue Date: 23-06-16
Approval expiry date: 1 September 2021

Specialist Welding Services Ltd

Stainless Steel Tanks and Pipework DWI 56/4/1367
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Version 1.0 Revision C (Dated: 09 August 2019)
Approval expiry date: 15 August 2024

Staptina Engineering Services Ltd

Staptina Bespoke stainless steel fabrications: Pipework, Baffles, Troughs,
Tanks, Support and Access systems DWI 56/4/567a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 24838IFU 12 June 2013
Approval expiry date: 31 March 2024

Tema Engineering Limited

Stainless Steel Pipework, Tanks and Vessels for Water Use DWI 56/4/1376a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No:01; Issue Date:25/07/2019
Approval expiry date: 6 October 2024

Vessco Engineering Ltd

Fabricator of Bespoke Stainless Steel Products: Pressur Vessels, Tanks and
Pipes DWU 56/4/1345a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1, Rev 1: 24 January 2019
Approval expiry date: 20 February 2024

Yorkshire Stainless Ltd

Stainless Steel Pipes, Tubes, Fittings and Flanges DWI 56/4/1368
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Stainless Steel Pipes, Tubes, Fittings and Flanges. Issue 1 Date:
06/06/2019
Approval expiry date: 17 July 2024

Uncontrolled if printed Page 34 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.11 Coated pipes suitable for total immersion in water

Saint-Gobain PAM UK Ltd
System CL DWI 56/4/283
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SAINT GOBAIN PAM UK. Instructions for Use Document for
System CL Pipes. Issue Number 9. Date: 25th May 2009
Before connection to the supply, the water undertaker or their
appointed agent must carry out tests to establish that migration from
the cement mortar lining will not cause a contravention of the upper
prescribed concentration for hydrogen ion in the relevant Regulations.
Approval expiry date: 5 May 2023
System XL DWI 56/4/1317
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SAINT GOBAIN PAM UK. Instructions for Use Document for
System XL. Issue number 8. Dated: 1st January 2013
Before connection to the supply, the water undertaker or their
appointed agent must carry out tests to establish that migration from
the cement mortar lining will not cause a contravention of the upper
prescribed concentration for hydrogen ion in the relevant Regulations.
Approval expiry date: 5 May 2023

Uncontrolled if printed Page 35 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.1.12 Pipes coated with a factory applied polyolefin

Saint-Gobain PAM UK Ltd
Blutop DWI 56/4/823
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Number 2. Date: 1st January 2009
Approval expiry date: 20 February 2025

B.2 Well Casings, Screens and Rising Mains

Angus Flexible Pipelines
Angus Wellmaster Flexible Rising Main DWI 56/4/1020
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE (IFU) DOCUMENT
ANGUS/IFU/WM. Wellmaster The Flexible Rising Main. Document:
ANGUS/IFU/WM. Issue: 004. Dated: September 2016
Prior to use the water supplier carries out a risk assessment to
provide for a suitable flushing regime validated, where appropriate, by
monitoring when the product has been out of supply for a period of
time.
Approval expiry date: 9 October 2021

Aqseptence Group SAS

Johnson Screen, Casing & johnson Riser Pipe and Accessories DWI 56/4/653
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Aqseptance Group SAS – Johnson Screen, Casing and Johnson
Riser Pipes Issue 2 Dated 17th April 2019
Approval expiry date: 22 June 2024

Boode UK Ltd
Boode Waterwell Systems PVC Screen and Casing DWI 56/4/958
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Boode Waterwell Systems PVC Screen and Casing. Instructions
for Use . Issue 2 - 1.1.2018
Approval expiry date: 9 July 2023

GOLAN Plastic Products Ltd

PEXGOL DWU 56/4/1259
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No. 1. Dec 2016
Approval expiry date: 17 February 2023

Uncontrolled if printed Page 36 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Stuwa-Konrad Stukerjurgen GmbH

PVC Screens, Casings, Fittings and Accessories DWI 56/4/1061
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU approval STÜWA – Konrad Stükerjürgen GmbH. PVC
screens and casings. Issue date = 07/19/2012. Issue number = 3
Approval expiry date: 13 December 2023
Stainless Steel Screens, Casings, Fittings and Accessories DWI 56/4/1060
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU approval STÜWA – Konrad Stükerjürgen GmbH. Stainless
steel screens and casings. Issue date = 07/19/2012. Issue number = 3
Approval expiry date: 23 July 2022
STUWA Stainless Steel Riser Pipes DWI 56/4/1077
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Approval STÜWA – Konrad Stükerjürgen GmbH. Stainless
Steel Riser Pipes. Issue 2 Dated 29/11/2012
Approval expiry date: 11 September 2022

Uncontrolled if printed Page 37 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.3 Products for Conveyance of Water -Emergency Use

For products in this section the following condition applies:
These products are primarily intended for emergency use and are approved for limited use only and may not
be permanently installed in, or used in conjunction with any system for treating or distributing public water
supplies. If the proposed use will extend beyond a 90 day period of use on any one occasion, then advice
from the DWI should be sought before installation and use.
NOTE: some of these products may be suitable for limited use during planned maintenance. In this case it is
the responsibility of the water supplier to undertake a thorough risk assessment of the proposed use,
including fitness-for-purpose and why other products, already fully approved under the relevant regulations
cannot be used. Use of any of these products during planned maintenance shall be in accordance with the
condition set out above.

B.3.1 Hoses
AAH Europe Hose Company Ltd (T/A Snap-tite)
Snap-Tite TE Range – Blue Hose DWI 56/4/62
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU LAYFLAT POTABLE WATER HOSE FOR EMERGENGY
USE – “SNAP-TITE TE HOSE RANGE’ Rev.2 Date: 26/06/20
Approval expiry date: 6 July 2024

Angus Flexible Pipelines

Super Aquaduct DWI 56/4/1005
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE (IFU) DOCUMENT. ANGUS SUPER
AQUADUCT. Document: ANGUS/IFU/SA. Issue: 006. Dated:
September 2016
(i) after disinfection the product is flushed for its entire length before
being brought into service; (ii) when in use the main is kept
continually in flow; (iii) the product is primarily intended for emergency
use and is approved for limited use only and may not be permanently
installed in, or used in conjunction with any system for treating or
distributing public water supplies. If the proposed use will extend
beyond a 90 day period of use on any one occasion, then advice from
DWI should be sought before installation and use.
Approval expiry date: 9 October 2021

Uncontrolled if printed Page 38 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

B.3.2 Bowsers/tanks
Enduramaxx Ltd
Enduratank DWI 56/4/1242
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Enduratank Potable Water Storage Tanks, Issue number: 1
Issue date 27/10/16
The product is approved for emergency use only and may not be
permanently installed in any system for treating or distributing public
water supplies. If the proposed use will extend beyond a 90 day
period of use on any one occasion, then advice from the DWI should
be sought before installation and use.
Approval expiry date: 9 April 2022

JFC Manufacturing Co. Ltd

AquaCube Emergency Water Tank DWI 56/4/765
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Revision 001, May 2016
Approval expiry date: 3 October 2021

Trailer Engineering Ltd

Emergency Drinking Water Bowsers DWI 56/4/707
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Drinking Water Bowser Operating Manual, Vol. 8, dated October
2004
Approval expiry date: 28 October 2024

Whale Tankers Ltd

Whale Drinking Water Bowser DWI 56/4/662
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue date 30/07/2013
Approval expiry date: 10 December 2023

B.3.3 Liner bags

Arlington Packaging (Rental) Ltd
Arlington 1000 Litre Bag-in-Box Combo Liner DWI 56/4/796
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Arlington 1000 Litre Water Tank
Issue: 4.2 Date of Issue: June 2020
This product is primarily intended for emergency use and is approved
for limited use only and may not be permanently installed in, or used
in conjunction with any system for treating or distributing public water
supplies. If the proposed use will extend beyond a 90 day period of
use on any one occasion, then advice from the DWI should be sought
before installation and use.
Approval expiry date: 5 August 2025

Uncontrolled if printed Page 39 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PART C LINING, COATINGS, SEALANT AND REPAIR

MATERIALS

C.1 In-situ Installed (tubular) pipe linings

Aqualiner Ltd
Water Pipe Lining DWI 56/4/910
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Water Pipe Lining. Version No 5 Issue Date:
21 October 2010
Approval expiry date: 6 November 2021

C.2 In-situ applied Pipe Coatings

In-situ applied lining products approved for use by the Authorities for the relining of existing water
mains/pipes must be applied in accordance with strict operational requirements as documented in the Water
Industry Information & Guidance Note IGN 4-02-02 http://www.water.org.uk/home/member-services/wis-
and-ign/archived-documents/ign-4-02-02.pdf "Code of Practice: In-situ resin lining of water mains” and the
Water Industry Specification WIS 4-02-01 http://www.water.org.uk/home/member-services/wis-and-
ign/archived-documents/wis-4-02-01-v2.1---march-2009.pdf “Operational Requirements: In situ resin lining of
water mains".
The coatings listed in this section have been subject to review by DWI (including testing), on the basis of
their proposed use with inert substrates such as metallic or cement based structures (or as specified in the
manufacturer’s Instructions for Use (IFU)), and upon the detailed application and curing requirements set out
in the IFU. They have not been evaluated for any other aspect, such as fitness for purpose.
For use with other non-metallic non-cementitious materials, such as plastics, other coatings/linings, and
rubbers, a specific application for approval would be required for use of the coating with a specific substrate.

C.2.1 Coatings based on epoxy resins

These products must be applied by a certified contractor.

Radius Subterra – a part of RadiusPlus Ltd

Subcote 173/90 WS 34/1/124a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Subterra Subcote 173/90 Issue 10. Date 22 Sept 2017
Approval expiry date: 4 October 2022

Uncontrolled if printed Page 40 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

C.2.2 Coatings based on polyurethane

These products must be applied by a certified contractor.

3M United Kingdom
3M Scotchkote Pipe Protection Liner 2100 DWI 56/4/1037
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU 29P-2100
In-situ rapid setting polymeric lining of potable water mains. Coating system 3M Scotchkote
Pipe Protection Liner 2100
Issue 7 – January 2018

Approval expiry date: 15 March 2023

3M Scotchkote Pipe Renewal Liner 2400 DWI 56/4/1031
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 3M Scotchkote Pipe Renewal Liner 2400 Instructions for Use
Document 29P-2400 June 2017 Issue number 6
Approval expiry date: 2 October 2022

Radius Subterra – a part of RadiusPlus Ltd

Subcote FLP II DWI 56/4/1286
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue date 16 August 2019, Issue No. 6
The minimum cure time is one hour at a minimum temperature of 3°C
Approval expiry date: 30 March 2025

C.2.3 Coatings for small diameter pipes

This section covers pipes up to 75 mm internal diameter. The products listed in this section shall be applied
by certified contractors in accordance with strict operational requirements as documented in the Water
Industry Specification WIS 4-02-03 "Operational Requirements : In-situ polymeric lining of service pipes"
(document is available from https://www.water.org.uk/publications/WIS-IGN )

3M United Kingdom
3M Scotchkote Rapid Setting Polymeric Lining 166L DWI 56/4/1032
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 29P-SP. Issue No: 7. Issue Date: March 2017
Approval expiry date: 29 July 2022

Pipe Restoration Technologies LLC

ePipe UK DWI 56/4/995
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IN-SITU HYDROPHOBIC POLYMERIC LINING OF POTABLE
WATER SERVICE LlNES. lnternal Coating System ePIPE® UK
lssue Date: July 6, 2017 lssue No: 010
Approval expiry date: 1 October 2022

Uncontrolled if printed Page 41 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

C.3 Site applied coatings for water retaining structures

The products listed below in this section, in addition to being approved for site applied coatings for water
retaining structures, are suitable for use in large diameter mains where they can be applied by hand e.g.
brush or spray.
The coatings listed in this section have been subject to review by DWI (including testing), on the basis of
their proposed use with inert substrates such as metallic or cement based structures (or as specified in the
manufacturer’s Instructions for Use (IFU)), and upon the detailed application and curing requirements set out
in the IFU. They have not been evaluated for any other aspect, such as fitness for purpose.
For use with other non-metallic non-cementitious materials, such as plastics, other coatings/linings, and
rubbers, a specific application for approval would be required for use of the coating with a specific substrate.

C.3.1 Coatings based on epoxy resins

The following conditions apply unless otherwise indicated:
(i) the minimum cure time is 16 hours; and
(ii) the minimum cure temperature is 3°C.

Radius Subterra – a part of RadiusPlus Ltd

Subcote 173/90 WS 34/1/124b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Subterra Subcote 173/90 Issue 4. Date 22 September 2017
Approval expiry date: 4 October 2022

Sherwin-Williams Protective and Marine Coatings

Macropoxy P300 DWI 56/4/253
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No 9; Issue date: June 2020
Approval expiry date: 1 September 2021

Sika Ltd
Sikagard 62 DWI 56/4/197
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Sikagard 62 -2 part Epoxy protective coating
Issue No :002 Issue Date: May 2012
The product must be cured in accordance with the cure curves
provided in the Instructions for Use. The required cure time can be
calculated by the user from the minimum daily temperature at the site
of application. If the temperature cannot be measured and recorded
then a minimum cure period of 21 days must be used.
Approval expiry date: 3 September 2022

Uncontrolled if printed Page 42 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

C.3.2 Coatings based on polyurethane

Axalta Coating Systems
Acothane DW Blue DWI 56/4/1059
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use Document - Acothane DW. Issue 8 dated
November 2019
The product must be cured for a minimum period of 7 days at a
minimum temperature of 3°C.
Approval expiry date: 24 November 2024
Acothane DW Cream DWI 56/4/1052
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use Document - Acothane DW. Issue 8, dated
November 2019
The product must be cured for a minimum period of 7 days at a
minimum temperature of 3°C.
Approval expiry date: 24 November 2024
Acothane LV Sealer DWI 56/4/1058
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use Document - Acothane DW. Issue 8, dated
November 2019
The product must be cured for a minimum period of 3 hours at a
minimum temperature of 3°C, this product must then be overcoated
with Acothane DW.
Approval expiry date: 24 November 2024

BASF plc Construction Chemicals (UK) Ltd

Masterseal M 808 DWI 56/4/1080a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal M808 - APPLICATION TO POTABLE WATER
CONTACT AREAS INSTRUCTIONS FOR USE Ref Rev 5 22052018
Approval expiry date: 29 November 2024
Masterseal M 808 additional light grey colour DWI 56/4/1080b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal M808 - APPLICATION TO POTABLE WATER
CONTACT AREAS INSTRUCTIONS FOR USE Ref Rev 5 22052018
Approval expiry date: 29 November 2024

Uncontrolled if printed Page 43 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Line-X Protective coatings

Aquaurethane Extreme DWI 56/4/874
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use (IFU). LINE-X Aquaurethane Extreme. Issue
number 7, August 2016
i) The product must be cured for a minimum of 5 days at a minimum
substrate temperature of 3°C and
ii) this product is for use on water retaining structures only.
Approval expiry date: 18 September 2021

Radius Subterra – a part of RadiusPlus Ltd

Subcote FLP II DWI 56/4/1286b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Subcote FLP II Product Description and Manufacturer's IFU:
Issue date 1 April 2020, Issue No 2
The minimum cure time is one hour at a minimum temperature of 3°C
Approval expiry date: 31 March 2025

C.4 Flexible covers and linings for water retaining

structures
Note: Laminated flexible covers and linings for water retaining structures may not necessarily have been
assessed for uses totally immersed in water, e.g. as baffles. For information on use see individual product
Instructions for Use (IFU) document.

Flag S.p.a
Flagon Geo P/AT DWI 56/4/856
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MANUFACTURER’S OFFICIAL INSTRUCTIONS FOR USE
(IFU). ISSUE NUMBER: 3. 18.02.2014. PRODUCT: FLAGON GEO
P/AT
Approval expiry date: 4 October 2022

Power Plastics Ltd

PowerPlas ® TL850 Tank Liner DWI 56/4/1385
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue Date: Dec 2019; Issue No. 1.0
Approval expiry date: 26 January 2025

Sensor (UK) Ltd

Sensorline DWI 56/4/1066a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SENSORLINE – PE GEOMEMBRANES (IFU VERSION 4.9)
Issue date 9 November 2015
Approval expiry date: 19 March 2023

Uncontrolled if printed Page 44 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

C.5 Cementitious coatings

BASF plc Construction Chemicals (UK) Ltd
MasterSeal 581 DWI 56/4/1227
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal 581 - APPLICATION TO POTABLE WATER
CONTACT AREAS INSTRUCTIONS FOR USE Ref Rev 2 22052018
This product must be cured for a minimum of 3 days at a minimum
temperature of 3°C or in accordance with the cure curve provided in
the manufacturer's instruction for use document
Approval expiry date: 30 June 2021
MasterSeal 581 with MasterSeal 600 DWI 56/4/1103
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal 581 with MasterSeal 600 - APPLICATION TO
POTABLE WATER CONTACT AREAS INSTRUCTIONS FOR USE
Ref Rev 2 22052018
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturer's instruction for use document
Approval expiry date: 28 April 2024
MasterSeal 586 with MasterSeal 600 DWI 56/4/86
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal 586/MasterSeal 600 - APPLICATION TO POTABLE
WATER CONTACT AREAS INSTRUCTIONS FOR USE Ref Rev 3
22052018
Approval expiry date: 30 March 2025
MasterSeal 588 DWI 56/4/1128
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal 588 - APPLICATION TO POTABLE WATER
CONTACT AREAS INSTRUCTIONS FOR USE Ref Rev 3 22052018
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturer's instruction for use document
Approval expiry date: 28 April 2024

FIS Products
Premcrete Hydroseal FX DWI 56/4/1356
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: UXHP 1017 Revision date: 11/03/2019
The product must be cured in accordance with the cure curves
provided in the Instructions for Use. The required cure time can be
calculated by the user from the minimum daily temperature at the site
of application. If the temperature cannot be measured and recorded
then a minimum cure period of 21 days must be used. The minimum
temperature for application is 7°C
Approval expiry date: 17 May 2022

Uncontrolled if printed Page 45 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Premcrete Teknolevel FS DWI 56/4/1359

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 01587 Revision, Date 19/06/2019
Approval expiry date: 5 November 2025

Flexcrete Technologies Ltd

Cementitious Coating 851 Grey DWI 56/4/1159
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Cementitious Coating
851 Grey
Issue: 851/031/011 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Cementitious Coating 851 White DWI 56/4/1160
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Cementitious Coating
851 White
Issue: 851/031/011 | Issue Date: July 2020
This product must be cured for a minimum of 7 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Cemprotec 851F DWI 56/4/1340
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE IN PUBLIC SUPPLY CEMPROTEC
851F
Issue date: October 2018; Issue No: 851F/031/001
Approval expiry date: 16 June 2024
Monolevel 844SP DWI 56/4/1161
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Monolevel 844SP
Issue: ML844SP/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025

International Paint Ltd

Intercrete 4820 DWI 56/4/1054
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4820 Issue:
4820/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 17 May 2022

Uncontrolled if printed Page 46 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Intercrete 4841 DWI 56/4/1053

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4841
Issue: 4841/031/011 | Issue Date: July 2020
The Grey product must be cured for a minimum of 21 days at a
minimum temperature of 7°C and the White product must be cured for
a minimum of 7 days at a minimum temperature of 7°C or in
accordance with the cure curve provided in the manufacturers IFU
Approval expiry date: 27 October 2025

Vandex International Ltd

CEMLINE UM1 DWI 56/4/1099
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: VXI IFU UK CEMLINE UM1, 12.2015 / 1
Approval expiry date: 2 December 2023
CEMLINE BB-W DWI 56/4/1093
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: VXI IFU UK CEMLINE BB-W, 12.2015 / 1
Approval expiry date: 2 December 2023
CEMLINE CG DWI 56/4/1094
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: VXI IFU UK CEMLINE CG, 12.2015 / 1
Approval expiry date: 2 December 2023
VANDEX BB 75 DWI 56/4/1092
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 2 Date: 04/11/2020
Approval expiry date: 2 December 2023
VANDEX PREMIX DWI 56/4/1097
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 1.12.2013/1st issue
Approval expiry date: 2 December 2023
VANDEX SUPER DWI 56/4/1098
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 1/12/2013/1st issue
Approval expiry date: 2 December 2023

Xypex (UK) LLP

Xypex Concentrate DWI 56/4/1261
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: ISSUE NO: 0921C: 3rd April 2019 (221019-C): XDS: Rev-04-16
Approval expiry date: 16 February 2022
Xypex Modified DWI 56/4/1262
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE. XYPEX MODIFIED. ISSUE NO:
1210M – 12th October 2016
Approval expiry date: 16 February 2022

Uncontrolled if printed Page 47 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

C.6 Sealant & Repair Materials

BASF plc Construction Chemicals (UK) Ltd
MasterEmaco S420 with MasterSeal 600 DWI 56/4/1064
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterEmanco S420 with MasterSeal 600 - APPLICATION TO
POTABLE WATER CONTACT AREAS INSTRUCTIONS FOR USE
Ref Rev 2 22052018
Before connection to the supply, the water undertaker or their
appointed agent, must carry out tests to establish that migration from
the cement mortar lining will not cause a contravention of the upper
prescribed concentration for hydrogen ion in the relevant Regulations .
This product must be cured for a minimum of 3 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturer's instruction for use document
Approval expiry date: 25 February 2023
MasterSeal 930 and MasterSeal 933 DWI 56/4/144
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MasterSeal 930 joint bandage with MasterSeal 933 adhesive -
APPLICATION TO POTABLE WATER CONTACT AREAS
INSTRUCTIONS FOR USE Ref Rev 2 22052018
This product must be cured for a minimum of 10 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturer's instruction for use document

Approval expiry date: 28 April 2024

FIS Products
Premcrete Teknocem HB50 DWI 56/4/1357
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 01553 Revision, Date 18/06/2019
Approval expiry date: 27 October 2025
Premcrete Teknocem Rapid DWI 56/4/1358
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: CODE: UXHP 1076 REVISION DATE: 11.03.19
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 5 October 2021
Premcrete Teknoprime 841 DWI 56/4/1360
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: CODE: UXHP 1091 REVISION DATE: 11.03.19
Approval expiry date: 16 May 2022

Uncontrolled if printed Page 48 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Premcrete Tie Hole Sealer DWI 56/4/1361

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: CODE: UXHP 1305 REVISION DATE: 18.12.2015
Approval expiry date: 1 October 2022

Flexcrete Technologies Ltd

Fastfill DWI 56/4/1162
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Fastfill Issue:
FFILL/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Monomix DWI 56/4/1163
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply MONOMIX Issue:
MMIX/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Monomix WS DWI 56/4/397
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply MONOMIX WS
Issue: MMIXWS/031/010 | Issue Date: July 2020

This product must be cured for a minimum of 21 days at a minimum

temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Steel Reinforcement Protector 841 DWI 56/4/1164
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Steel Reinforcement
Protector 841 Issue: 841/031/009 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Tiefill DWI 56/4/1287
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Tiefill Issue:
TFILL/031/003 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025

Uncontrolled if printed Page 49 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Fosroc Ltd
Conbextra Bedding Mortar DWI 56/4/1271
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Conbextra Bedding Mortar IFU Issue date: Apr 2017; Issue
number BM1
Approval expiry date: 28 November 2022
Renderoc Plug 20 DWI 56/4/297
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Renderoc Plug 20. Instructions for use. Ref: RRP20 IFU v3; Apr
13
Approval expiry date: 26 April 2023

International Paint Ltd

Intercrete 4800 DWI 56/4/1403
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4800 Issue:
4800/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Intercrete 4800WS DWI 56/4/1408
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4800WS
Issue: 4800WS/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025
Intercrete 4802 DWI 56/4/1055
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4802
Issue: 4802/031/010 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 17 October 2025
Intercrete 4807 DWI 56/4/1404
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4807
Issue: 4807/031/003 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025

Uncontrolled if printed Page 50 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Intercrete 4871 DWI 56/4/1056

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use in Public Water Supply Intercrete 4871 Issue:
4871/031/009 | Issue Date: July 2020
This product must be cured for a minimum of 21 days at a minimum
temperature of 7°C or in accordance with the cure curve provided in
the manufacturers IFU
Approval expiry date: 27 October 2025

MG Solutions (UK) Ltd

Aquron 2000 DWI 56/4/1291
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Aquron 2000 Colliodal Silicate for waterproofing of concrete IFU.
Issue Date 21/08/2017; Issue Number 1.1
Approval expiry date: 2 November 2022

Natural Cement Distribution Ltd

NATCEM 35 DWI 56/4/1090
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Product Information: NATCEM 35 Fast Setting and Fast Curing
Mortar . Issue date 26/06/2017 issue number 01
Approval expiry date: 10 March 2023
NATCEM AC DWI 56/4/840
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Natcem AC 10 January 2020 Issue 3
Approval expiry date: 5 May 2025
NATCEM D DWI 56/4/1216
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DRY PRE-BLENDED GROUT
NATCEM D
Issue Date: 23/03/16, Issue Number 1
Approval expiry date: 27 December 2021
NATCEM DW DWI 56/4/1049
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Natcem DW- Fast Setting Mortar. Issue date: 2013-03020; Issue
number: 01
Approval expiry date: 10 March 2023
Shotcrete 513 DWI 56/4/1089
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Shotcrete 513 - Fast Setting Dry Spray Concrete. Issue date:
2017-06-26; Issue number: 01
Approval expiry date: 10 March 2023
Waterstop DWI 56/4/1217
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: FAST SETTING NATURAL CEMENT WATERSTOP
Issue: 2, Date: 20/10/2016
Approval expiry date: 27 December 2021

Uncontrolled if printed Page 51 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Penetron UK Ltd
Penecrete Mortar DWI 56/4/1130
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use PENECRETE MORTAR CRYSTALLINE
WATERPROOF MORTAR. Issue No:2, (Dated: 12/02/2014, Re-
issued: 05/03/2017)
Approval expiry date: 1 October 2024
Penectron Crystalline Waterproof Coating DWI 56/4/1137
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instruction for Use PENETRON CRYSTALLINE WATERPROOF
COATING. Issue I/ 2, (Issue date: 19/05/2014, Revision date:
09/02/2017)
Approval expiry date: 1 October 2024

Sika Ltd
Sika Monotop 610/615 Concrete Repair System DWI 56/4/834
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Sika Mono Top – 615 Cementitious High Build Concrete Repair
Mortar. Issue No: 001. September 2007
The product must be cured in accordance with the cure curves
provided in the IFU. The required cure time can be calculated by the
user from the minimum daily temperature at site of application. If the
temperature cannot be measured and recorded then a minimum cure
period of 21days at a minimum substrate temperature for application
is 5°C.
Approval expiry date: 12 March 2022
Sikadur Combiflex SG jointing system using Sikadur 31 DW DWI 56/4/94
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Sikadur Combiflex SG Jointing system Issue No:006 October
2011
The minimum cure temperature is 7°C for a minimum cure time of 21
days. At temperatures greater than 7°C the product must be cured in
accordance with the cure curve provided in the Instructions For Use.
The required cure time can be calculated by the user from the
minimum daily temperature which must be recorded at site.
Approval expiry date: 3 October 2021
Sikadur Combiflex SG jointing system, using Sikadur 31 DW Rapid DWI 56/4/1124
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Sikadur Combiflex SG Jointing System, using Sikadur 31 DW
Rapid. Issue No: 01, September 2013
Approval expiry date: 4 February 2025

Vandex International Ltd

CEMLINE STON DWI 56/4/1095
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: VXI IFU UK CEMLINE STON, 12.2015 / 1
Approval expiry date: 2 December 2023

Uncontrolled if printed Page 52 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Vandex Plug DWI 56/4/1096

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 7.11.2018 / 3rd issue
Approval expiry date: 2 December 2023

Xypex (UK) LLP

Xypex Admix C-1000 NF DWI 56/4/1263
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No 1210A1 - 12th October 2016
Approval expiry date: 16 February 2022
Xypex Admix C-500 NF DWI 56/4/1244
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: XYPEX (UK) LLP IFU - XYPEX ADMIX C-500 NF. Issue date:
4th December 2018; Issue number : 0920A5
Approval expiry date: 28 January 2024
Xypex Patch'n Plug DWI 56/4/1100
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: ISSUE NO: 1623P: 16TH April 2019 (310719-C): XDS: Rev-06-
16
Approval expiry date: 5 June 2024

Uncontrolled if printed Page 53 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PART D MEMBRANE AND FILTRATION SYSTEMS

For products in this section the following general condition applies:
Products must be installed upstream of any final point of disinfection.

D.1 Membrane and Filtration Elements/Systems

Amazon Filters Ltd
Amazon SupaGard Cartridge Filters DWI 56/4/702
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE. AMAZON SUPAGARD AND
SUPASPUN II FILTER CARTRIDGES. ISSUE NUMBER: 9. DATE:
25th February 2010
Approval expiry date: 11 August 2025
Amazon SupaSpun II Cartridge Filters DWI 56/4/702
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE. AMAZON SUPAGARD AND
SUPASPUN II FILTER CARTRIDGES. ISSUE NUMBER: 9. DATE:
25th February 2010
Approval expiry date: 11 August 2025

DuPont Water Solutions

Memcor CMF- S S10V Range of Microfiltration submodules (submerged
PVDF Membranes) DWI 56/4/973
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR THE MEMCOR
CMF-S S10V MICROFILTRATION SUBMODULES (SUBMERGED
PVDF MEMBRANES). Issue:- M Date:- 03/03/2020
Approval expiry date: 19 January 2022
Memcor CMF-L L10N DWI 56/4/1254
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MEMCOR CMF-L L10N RANGE OF MICROFILTRATION
SUBMODULES (PVDF MEMBRANES)
Issue date: 03/03/2020 Issue No: OM-12596C
Approval expiry date: 5 March 2022
Memcor CMF-L L10V Range of Microfiltration Submodules (PVDF
Membranes) DWI 56/4/977
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR THE MEMCOR
CMF-L L10V MICROFILTRATION SUBMODULES (PVDF
MEMBRANES). Issue:-J Date:- 03/03/2020
Approval expiry date: 19 January 2022

Uncontrolled if printed Page 54 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Memcor CMF-L L20N DWI 56/4/1255

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MEMCOR CMF-L L20N RANGE OF MICROFILTRATION
SUBMODULES (PVDF MEMBRANES)
Issue date: 03/03/2020 Issue No: OM-12597C
Approval expiry date: 5 March 2022
Memcor CMF-L L20V Range of Microfiltration Submodules (PVDF
Membranes) DWI 56/4/978
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR THE MEMCOR
CMF-L L20V MICROFILTRATION SUBMODULES (PVDF
MEMBRANES). Issue:-E Date:- 03/03/2020
Approval expiry date: 19 January 2022
Memcor CMF-L L40N DWI 56/4/1305
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use document for the MEMCOR CP2 L40N
ULTRAFILTRATION SUBMODULE (PVDF MEMBRANE)
Issue date: 03/03/2020; Issue No: OM-13807 B
Products must be installed upstream of any final point of disinfection
Approval expiry date: 22 January 2023
Memcor CMF-M10C Continuous Microfiltration Module (Polypropylene
Membranes) DWI 56/4/975
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR THE MEMCOR
CMF M10C CONTINUOUS MICROFILTRATION MODULE
(POLYPROPYLENE MEMBRANES). Issue:- G Date:- 03/03/2020
Approval expiry date: 19 January 2022
Memcor CMF-S S10N DWI 56/4/1256
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: MEMCOR CMF-S S10N RANGE OF MICROFILTRATION
SUBMODULES (SUBMERGED PVDF MEMBRANES)
Issue date: 03/03/20 Issue No: OM-13219B
Approval expiry date: 5 March 2022
Memcor CMF-S S10T Microfiltration Submodule (submerged Polypropylene
Membranes) DWI 56/4/976
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT FOR THE MEMCOR
CMF-S S10T MICROFILTRATION SUBMODULE (SUBMERGED
POLYPROPYLENE MEMBRANES). Issue:-H Date:- 03/03/2020
Approval expiry date: 19 January 2022

Envirogen Group
Deltapor MW and MWA Filter Cartridges DWI 56/4/1274
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Envirogen Deltapor MW and MWA Filter Cartridges, Issue Date;
26/09/2017; Issue Number 2
Approval expiry date: 3 April 2023

Uncontrolled if printed Page 55 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Hydranautics
HYDRAcap DWI 56/4/689
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: HYDRAcap Membrane Ultrafiltration Module Instructions for
Use, Issue 7 dated 23/1/2013
Approval expiry date: 1 March 2022

Mecana Umwilttechnik GmbH

Pile Cloth Media Filter (PCMF) DW2/10 - DW27/135 DWI 56/4/1215
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Document. Application for a pile cloth filtration system in
drinking water scope.Filter types DW2/10 - DW27/135 Issue Number:
Rev: 5; Issue Date 24th May 2019
Approval expiry date: 28 November 2022

Microdyn-Nadir US Inc
8040-SBNF-DWI Membrane Elements DWI 56/4/1218
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use 8040-SBNF-DWI Membrane Elements
Version 1.1; Issue date: 22 February 2017
Products must be installed upstream of any final point of disinfection
Approval expiry date: 21 December 2022
8040-SBUF-DWI DWI 56/4/1030
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use. 8040-SBUF-DWI Membrane Elements.
Version 1.1 Issued 22 February 2017
Approval expiry date: 15 November 2023

Pall Corporation
Pall GF Plus Filter Units, Type MWH27 Dwi 56/4/1336
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU for Pall® ‘GF Plus’ filter units Type ‘MWH27’. Issue 9
17/01/2019
Products must be installed upstream of any final point of disinfection
Approval expiry date: 30 January 2025

Pall International Sarl

Pall Microza UNA-620C microfiltration module DWI 56/4/795
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use for membrane prodcuts in water supply -
Instructions for use document for Pall Microza UNA-620C Micro-
filtration modules, Issue number 3, Date of issue:26 July 2006
Approval expiry date: 16 August 2025

Uncontrolled if printed Page 56 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PCI Membranes
C10 Module DWI 56/4/234
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue J, 1 Nov 2017
Approval expiry date: 11 December 2021
CA202 membrane DWI 56/4/76
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue No K, 1 Nov 2017
Approval expiry date: 12 December 2021
ES404 membrane DWI 56/4/215
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue No N, 1 Nov 2017
Approval expiry date: 12 December 2021

PWN Technologies
CeraMac® Technology DWI 56/4/1179
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Dated: 11/02/2016 Issue No: 1.1 Rev 1.3
Approval expiry date: 17 January 2022

SUEZ Water Technologies & Solutions

Absolute.Za*DWI DWI 56/4/1325
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: ABSOLUTE.ZA DWI® Issue Date 30/07/2019; Issue No. Rev 1
Products must be installed upstream of any final point of disinfection
Approval expiry date: 5 March 2024
Ultrafiltration element ZW700B-8060/UF10/7B/R/0.8/40 DWI 56/4/1125
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: UKDWI/ZW700B-8060/Version 1. Date of issue: 08 January
2018
Approval expiry date: 19 January 2021
Ultrafiltration element ZW700B-8060/UF10/7B/X/0.8/40 DWI 56/4/1126
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: UKDWI/ZW700B-8060/Version 1, Date of issue: 08 January
2018
Approval expiry date: 19 January 2021
ZeeWeed 500c, Membrane Filtration Module DWI 56/4/628
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed 500c Membrane
Filtration Module. Document number: UKDWI/500c Revision 7. Date
of Issue: 08 January 2018.
Approval expiry date: 8 February 2022

Uncontrolled if printed Page 57 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

ZeeWeed 500d (340)Membrane Filtration Module DWI 56/4/835

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed® 500d
(340),500d (440), 500ds (350) Membrane Filtration Modules
Document number: UKDWI/500d Revision 8
Date of Issue: 12th May 2020
Approval expiry date: 21 February 2021
ZeeWeed 500d (440) Membrane Filtration Module DWI 56/4/835
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed® 500d
(340),500d (440), 500ds (350) Membrane Filtration Modules
Document number: UKDWI/500d Revision 8
Date of Issue: 12th May 2020
Approval expiry date: 21 February 2021
ZeeWeed 500ds (350) Membrane Filtration Module DWI 56/4/835
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed® 500d
(340),500d (440), 500ds (350) Membrane Filtration Modules
Document number: UKDWI/500d Revision 8
Date of Issue: 12th May 2020
Approval expiry date: 21 February 2021

SUEZ Water Technologies and Solutions Hungary Kft

ZeeWeed ® 700B-9060 Membrane Module DWI 56/4/1349
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document For element ZW700B-
9060/UF10/7B/XA/0.8/55
Issue date: 8 May 2019; Issue No: UKDWI/ZW700B-9060-v4
Products must be installed upstream of any final point of disinfection
Approval expiry date: 11 June 2024
ZeeWeed 1000 V4 DWI 56/4/1177
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed® 1000 V4
module. Document number: UKDWI/1000V4/R1. Date of Issue: 23
January 2018
Approval expiry date: 27 April 2025
ZeeWeed 1500 Series DWI 56/4/1013
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the ZeeWeed® 1500 Series.
Document number: UKDWI/1500/Revision 8. Date of Issue: 20
November 2018
Products must be installed upstream of any final point of disinfection
Approval expiry date: 10 June 2024

Uncontrolled if printed Page 58 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

X-FLOW B.V.
Aquaflex DWI 56/4/324
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: X-Flow Membrane Filtration Elements Version 7.0 26 May 2015
Approval expiry date: 18 August 2025
Aquaflex HP DWI 56/4/967
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use for X-Flow Membrane Filtration Elements
Version 7 26/05/2016
Approval expiry date: 21 November 2021
HFW 1000 DWI 56/4/1139
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU for HFW 1000, Version 1.2, Issue date: 15-10-2014
Products must be installed upstream of any final point of disinfection.
Approval expiry date: 29 September 2021
XIGA HP DWI 56/4/1023
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions For Use for X-Flow Membrane Filtration Elements
Version 7 26/05/2016
This product must be installed upstream of any final point of
disinfection.
Approval expiry date: 19 March 2023

D.2 Vessels and Containers for Membrane and Filtration

Elements
Amazon Filters Ltd
Single and Multiple Cartridge & Bag Filter Housings and Interconnecting
pipework DWI 56/4/879
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Amazon Single and Multiple Cartridge & Bag Filter Housings and
Interconnecting Pipework: INSTRUCTIONS FOR USE IN DRINKING
WATER SYSTEMS. Issue 2 November 2016
Approval expiry date: 11 August 2025

Eliquo Hydrok
Eliquo Hydrok Filter Housing Tank DWI 56/4/1386
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Version 1 Dated: 20/11/2019
Approval expiry date: 21 January 2025

Uncontrolled if printed Page 59 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Envirogen Group
Envirogen CF Filter Housing DWI 56/4/1257
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE ENVIROGEN CF FILTER HOUSING
Issue date: 01/12/2016 Issue number: 1
Approval expiry date: 12 March 2022

Evoqua Water Technologies Ltd

SFH PFH SSS Filter housing DWI 56/4/1191
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SPECTRUM_PFH-SPC1_INSTALLATION –
INSTRUCTIONS_0615v1 and SPECTRUM_SFH-
SPC1_INSTALLATION –INSTRUCTIONS_0615v1
Approval expiry date: 30 November 2021

Fileder Filter Systems

EFH/SFH/PFH (Cartridge Housings) DWI 56/4/848
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Range of 316 Stainless Steel Filter and Bags Housing . Version
2 . Issue date 18/10/11
Approval expiry date: 30 November 2021
SBH and PBF Stainless Steel Bag Housing DWI 56/4/848
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Range of 316 Stainless Steel Filter and Bags Housing . Version
2 . Issue date 18/10/11
Approval expiry date: 30 November 2021
SFH and PFH Stainless Steel Filter Housing DWI 56/4/848
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Range of 316 Stainless Steel Filter and Bags Housing . Version
2 . Issue date 18/10/11
Approval expiry date: 30 November 2021

Filtertec Systems Ltd

CF-DW Series cartridge filter housings DWI 56/4/1331
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: FILTERTEC CF-DW FILTER HOUSING Issue date: 19/08/2018;
Issue No: 2
Approval expiry date: 13 September 2023

Pentair Water India Pvt Ltd

Codeline RO Membrane Housing Codeline 80S Series (Coded Vessels) DWI 56/4/288
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: No 94566-NC, Issue No 3, Date Aug13
The product may only be used upstream of reverse osmosis filtration
Approval expiry date: 29 June 2021

Uncontrolled if printed Page 60 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Codeline RO Membrane Housing Codeline 80S Series (Non-coded Vessels) DWI 56/4/288
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: No 94566- NC, Issue No 3, Date Aug 13
The product may only be used upstream of reverse osmosis filtration
Approval expiry date: 29 June 2021

D.3 Electrodialysis Water Treatment Units

Suez Water Technologies & Solutions (USA Inc)
MK IV EDR Water Treatment System DWI 56/4/480
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: System: MK IV EDR Water Treatment Systems, Revision 1,
February 2018
Approval expiry date: 10 September 2024

D.4 Filter Media Containing Systems

Amiad Water Systems UK Ltd
DVF Media Filters DWI 56/4/1249
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Amiad Water Systems Automatic Filters DVF Media Filters, Issue
No: 16 Rev.1 Issue Date: 10.10.2016
Approval expiry date: 11 May 2022

DYNAMlK FlLTR Nocoń iWspólnicy Spółka Jawna

PRESSURE FILTRATION KIT DF FP/FDN 800÷3 500 DWI 56/4/1272
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: lssue Number: FP/FDN 800÷3 500/001/017 lFU; lssue Date:
01:02:2017
Approval expiry date: 20 December 2022

Hydro-Gen Engineering Ltd

Velocitek OVF Filter Vessel DWI 56/4/1400
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for use Velocitek OVF Filter Vessel. Issue Date:
14.04.2020; Version No. 2
Approval expiry date: 28 July 2025

Uncontrolled if printed Page 61 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

PART E OTHER WATER TREATMENT WORKS

INSTALLATIONS

E.1 Tanks
ABC Stainless Steel Ltd
Storage, process tanks and vessels DWI 56/4/542b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use : Stainless steel storage, Process Tanks and
Vessels . Issue no: 2 Date: 20th October 2003
Approval expiry date: 4 January 2023

Allied Storage Tank Ltd

Stainless Steel Tanks and Launders DWI 56/4/1258
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue date: 30/01/2017 Issue No.1
Approval expiry date: 26 February 2022

Asset International Ltd

Weholite Pipe and Panels DWI 56/4/513b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Weholite HDPE Pipes and Panels - Issue 5 September 2018
Approval expiry date: 2 February 2024

Barr + Wray Ltd

Barr + Wray Stainless Steel Media Filter DWI 56/4/1234a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue No: 1, 20 July 2016
Approval expiry date: 21 November 2021

Berry & Escott Engineering

Stainless Steel Pipework and Fabrications DWI 56/4/1362a
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Stainless Steel Fabricated Pipework
Approval expiry date: 1 May 2024

CST Industries Ltd

Aquastore Vitrium EN DWI 56/4/621
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: AQUASTORE STORAGE TANKS INSTRUCTIONS FOR USE
(IFU). Version 7 20 June 2017
Approval expiry date: 15 July 2022

Uncontrolled if printed Page 62 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

EPS Group
Stainless Steel Tanks & Pipework DWI 56/4/1267
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: EPS Group - Stainless Steel Tanks & Pipework, Issue 1
10/03/17
Approval expiry date: 27 March 2022

Filtec Water Services Ltd

Filtec "Selkie" Stainless Steel Products DWI 56/4/1396b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: HANDLING, INSTALLATION AND COMMISSIONING
INSTRUCTIONS FOR THE FILTEC SELKIE RANGE OF STAINLESS
STEEL PRODUCTS FOR USE IN CONTACT WITH TREATED OR
PARTIALLY TREATED POTABLE WATER. Dated: 29/04/2020;
Issue No: 01; Rev 02
Approval expiry date: 17 May 2025

Forbes Technology Ltd

Cheetah range of Tanks & Towers DWI 56/4/1292
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Handling, Installation and Commissioning Instructions for the
Forbes ‘Cheetah’ range of storage & process tanks & towers to
comply with Regulation 31 Issue no: QA379 Rev 05
Approval expiry date: 19 October 2022
Jaguar Range of Storage & Process Tanks & Towers DWI 56/4/1210
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: HANDLING, INSTALLATION AND COMMISSIONING
INSTRUCTIONS FOR THE FORBES JAGUAR RANGE OF
STORAGE & PROCESS TANKS & TOWERS
Issue Date: 10-10-2016 Issue No: QA427 Rev 02 Issue 1
Approval expiry date: 19 October 2021
Lion Range of Tanks & Towers DWI 56/4/1293
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Handling, Installation and Commissioning Instructions for the
Forbes ‘Lion’ range of storage & process tanks & towers to comply
with Regulation 31 Issue no:QA378 Rev 05
Approval expiry date: 19 October 2022

Homer Burgess Ltd

Tanks and associated Pipework, Weir Plates and Baffle Plates manufactured
from Stainless steel suitable for use with drinking water DWI 56/4/1107b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Title: Homer Burgess Ltd., Manufacturer’s official use instructions
for Stainless Steel Products in contact with Drinking Water.. Issue
Number Rev: 1 26/01/2016
Approval expiry date: 22 May 2023

Uncontrolled if printed Page 63 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

J.K Fabrications Limited

JKF 304 and 316 Stainless Steel Tanks DWI 56/4/732
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 3 Dated 10 December 2019
Approval expiry date: 21 January 2025

Monostore Ltd
Monostore SST - Recognised Grade Tanks DWI 56/4/1374
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 01/08/2019 Version 2.0
Approval expiry date: 31 July 2024

Ocean Kinetics Ltd

Unlined 316 & 316L Stainless Steel Tanks and Pipework DWI 56/4/1395b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: OK-IFU-2020-001 Rev 1; Issue date: 16/04/20
Approval expiry date: 22 April 2025

Permastore Ltd
Fusion ® V1100 DWI 56/4/1214
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue date 01/03/16, Issue number: P238 Rev 1
Approval expiry date: 19 December 2021
Isofusion (vitreous enamelled tank) DWI 56/4/594
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU P236 Rev 2 - IFU and Installation of ISOFUSION V700
Tanks for the storage of water (issued 18/03/16)
Approval expiry date: 31 March 2021
Trifusion ® DWI 56/4/1213
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue date 01/03/16, Issue Number: P285 Rev 1
Approval expiry date: 19 December 2021

Powerrun Pipe-Mech Ltd

Stainless Steel Grade 316L Potable Water Reservoir Tanks DWI 56/4/611
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PWRT (PP-ML) Rev 0 (First Issue) 16 April 2018
Approval expiry date: 11 September 2023

Ross-shire Engineering Ltd

Stainless Steel Water Tanks DWI 56/4/1381
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: TECHNICAL SPECIFICATION No. TS/SW/002 Date 18/10/19
Approval expiry date: 9 January 2025

Uncontrolled if printed Page 64 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Sayers Road Tankers Ltd

Stainless Steel Water Tanks DWI 56/4/1028
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use: Stainless Steel Water Tanks. Issue No: 2.
Issue Date: 15th August 2011
Approval expiry date: 8 August 2021

Silotank (Digestors, Silos & Tanks) Ltd

Leinster Range of Thermoplastic Tanks DWI 56/4/498
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Installation and Maintenance Manual For Leinster Range Of
Thermoplastic Tanks For Drinking Water and Raw Water to be
Treated for Drinking Water
Issue No. 7 Date: 14th August 2019
Approval expiry date: 9 March 2025
Leinster Range of Towers DWI 56/4/498
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Installation and Maintenance Manual For Leinster Range Of
Thermoplastic Tanks For Drinking Water and Raw Water to be
Treated for Drinking Water
Issue No. 7 Date: 14th August 2019
Approval expiry date: 9 March 2025

Staptina Engineering Services Ltd

Staptina Bespoke stainless steel fabrications: Pipework, Baffles, Troughs,
Tanks, Support and Access systems DWI 56/4/567b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 24838IFU 12 June 2013
Approval expiry date: 31 March 2024

Uncontrolled if printed Page 65 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

E.2 Underdrains
For some products, including underdrains, Section 3.4 of Advice Sheet 7 indicates that products constructed
from clay can be used without approval subject to the water supplier carrying out a risk assessment for
suitability of the product and its possible impact on drinking water quality

Black & Veatch

K Filter Floor DWI 56/4/833
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Installation & Test Procedure for K-Type Filter Floors Document
Ref: SSD 019 - Issue: L - Issue Date: 01/09/2020
Approval expiry date: 3 November 2025

De Nora Water Technologies UK Services Ltd

Tetra LP Block System DWI 56/4/522
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: INSTRUCTIONS FOR USE DOCUMENT. LP Block Underdrain
System. Issue number: 4 Date: 22 September 2020
Approval expiry date: 10 October 2025

Plasmor Ltd
Plasmor E and U Blocks DWI 56/4/988
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Plasmor E Blocks Instructions for Use . Issue 2. Issue Date:
22/12/2010
Approval expiry date: 5 March 2022

WesTech Engineering Inc

MULTIBLOCK® Media Retaining Gravity Filter Underdrain DWI 56/4/1312
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Manufacturers Instructions for Use (IFU) MULTIBLOCK Gravity
Filter Underdrains Version 1.2, Issue 2 Dated October 2018
Approval expiry date: 30 July 2025

Xylem Water Solutions Zelienople LLC

Leopold Type S Underdrain and I.M.S. 1000 Media Retainer DWI 56/4/1079
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025

Uncontrolled if printed Page 66 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Leopold Type S Underdrain and I.M.S. 200 Media Retainer DWI 56/4/1078
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025
Leopold Type S Underdrain and I.M.S. Cap DWI 56/4/371
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025
Leopold Type SL Underdrain and I.M.S. 1000 Media Retainer DWI 56/4/1079
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025
Leopold Type SL Underdrain and I.M.S. 200 Media Retainer DWI 56/4/1078
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025

Uncontrolled if printed Page 67 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Leopold Type SL Underdrain and I.M.S. Cap DWI 56/4/371

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Flume Installation:
Type S®/SL® Universal Flume Instruction for Use Document
TSLU-IFU-03
Date of Issue: 09 June 2020, Issue No: R03
Wall Installation:
Type S®/SL® Universal Wall Installation, Instruction for Use
TSLU-WALL-IFU-R01
Date of Issue: 09 June 2020, Issue No: R01
Approval expiry date: 14 June 2025
Leopold Type XA Underdrain and I.M.S. 1000 Media Retainer DWI 56/4/1105
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Type XA (TM) Underdrain Flume Installation, Operation and
Maintenance Manual
Date: 8th Aug 2017 Issue No: 2
Approval expiry date: 16 June 2024
Leopold Type XA Underdrain and I.M.S. 200 Media Retainer DWI 56/4/1105
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Type XA™ Underdrain Flume Installation, Operation and
Maintenance Manual
Date: 8th Aug 2017 Issue No: 2
Approval expiry date: 16 June 2024
Leopold Type XA Underdrain and I.M.S. Cap DWI 56/4/1105
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Type XA™ Underdrain Flume Installation, Operation and
Maintenance Manual
Date: 8th Aug 2017 Issue No: 2
Approval expiry date: 16 June 2024

E.3 Pressure vessels

A J Metal Products Ltd
Pressure Vessels DWI 56/4/1383
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU-1 A J METALS VESSELS FOR DRINKING WATER. Issue
date: 29/11/19, Issue No: 1 Document No: AJMP IFU 001
Approval expiry date: 10 December 2024

Barr + Wray Ltd

Barr + Wray Stainless Steel Media Filter DWI 56/4/1234b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Issue No: 1, 20 July 2016
Approval expiry date: 21 November 2021

Uncontrolled if printed Page 68 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Charlatte Reservoirs
Hydrochoc Butyl Bladder Surge Vessel DWI 56/4/1016
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Commissioning General Instructions for Hydrochoc Butyl Bladder
Surge Vessel for Clear Water. . Issue No: 2 Date of Issue: 2nd Nov
2016
Approval expiry date: 6 April 2022

CPE Pressure Vessels

CPE Pressure Vessels-304L and 316L Stainless Steel DWI 56/4/1135
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU-01 Rev 3 06/03/2013
Approval expiry date: 25 March 2024

Quantum Engineering Developments Ltd

Quantum Pressure Vessels- 304L DWI 56/4/1132
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU – 01, Rev D Issue date 31/01/2019
Approval expiry date: 30 March 2024
Quantum Pressure Vessels- 316L DWI 56/4/1133
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU – 01, Rev D Issue date 31/01/2019
Approval expiry date: 30 March 2024

E.4 Other Products used for the treatment of water

AJ Engineering and Construction Services Ltd
Stainless Steel Pipework and Fabrications DWI 56/4/1220b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Stainless Steel Pipework and Fabrications for water use. Issue
Number: WO41, Issue date: 04/08/2016
Approval expiry date: 19 September 2021

AMCON Europe s.r.o

Volute Dewatering Screw Press DWI 56/4/1144
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Volute Dewatering Press ES-CE-DW series Instruction Manual
<Operation> (Ver.DW1.01) 15.06.2019
Volute Dewatering Press ES-CE-DW series Instruction Manual <Transportation and
Installation> (Ver.DWT1.00) 15.06.2019
Supernatant from the press should either be returned to the head of
the works or run to waste.
Approval expiry date: 15 October 2024

Uncontrolled if printed Page 69 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Bridges Electrical Engineering Ltd

Bridges in-house fabricated stainless steel pipe spools and products DWI 56/4/1268b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Bridges in-house fabricated stainless steel pipe spools and
products, Issue 1 22/03/17
Approval expiry date: 14 May 2022

Colloide Engineering Systems Ltd

Lamella Separator Package (LSF) DWI 56/4/1172
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 90002-1502 B Date of Issue 10/02/2015
Approval expiry date: 23 February 2025

Craley Group Ltd

Atlantis Hydrotec - T&M Series DWI 56/4/1346
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Atlantis HYDROTEC M-Series Instructions for Use – UK
Issue Date: Jan. 2019; Revision No. 007
Atlantis HYDROTEC T-Series Instructions for Use – UK
Issue Date: Jan. 2019; Revision No. 005
Approval expiry date: 29 May 2024

ENEXIO 2H Water Technologies Ltd

TUBEdek FS41.50/84 PP DWI 56/4/878
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Information for Use Document. TUBEdek Lamella Separators
Type FS41.50PP & FS41.84PP. Version 1.5 April 2017
Approval expiry date: 4 July 2022

Filtec Water Services Ltd

Filtec "Selkie" Stainless Steel Products DWI 56/4/1396c
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: HANDLING, INSTALLATION AND COMMISSIONING
INSTRUCTIONS FOR THE FILTEC SELKIE RANGE OF STAINLESS
STEEL PRODUCTS FOR USE IN CONTACT WITH TREATED OR
PARTIALLY TREATED POTABLE WATER. Dated: 29/04/2020;
Issue No: 01; Rev 02
Approval expiry date: 17 May 2025

Flex EJ Ltd
Expansion Joint DWI 56/4/1382
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Stainless Steel Expansion Joints, Drinking Water Expansion
Joints, Instructions for Use, Revision A, Issue 1, Date of issue:
10.10.2019
Approval expiry date: 28 November 2024

Uncontrolled if printed Page 70 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Forbes Technology Ltd

Cheetah Tower Packings DWI 56/4/711
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: QA412 – Cheetah Pall Rings – Instructions for Use Manual.
Issue No. 6 Dated 07/03/2019
Approval expiry date: 28 October 2024

Homer Burgess Ltd

Tanks and associated Pipework, Weir Plates and Baffle Plates manufactured
from Stainless steel suitable for use with drinking water DWI 56/4/1107c
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Homer Burgess Ltd., Manufacturer’s official use instructions for
Stainless Steel Products in contact with Drinking Water.. Issue
Number Rev: 1 26/01/2016
Approval expiry date: 22 May 2023

Jacopa Ltd
Jacopa Ltd / Nordic Water Lamella Plate Separators DWI 56/4/622
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Jacopa Ltd / Nordic Water Products Lamella Plate Separators
Issue No.01 Date of issue: 3rd January 2020
Approval expiry date: 30 July 2023

Nijhuis Water Technology B.V.

IPF and NPF model of Dissolved Air Flotation units DWI 56/4/620
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: May 2019 rev 0 EJ
Approval expiry date: 19 August 2024

PAX Water Technologies Inc

PAX Water Monopod Mixers (PWM 100/150/250) and PAX Water Mixer
(PWM400/500/600) DWI 56/4/1335
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use PAX Water Monopod Mixer
(PWM100/150/250) and PAX Water Mixer (PWM400/500/600)
Issue Date: May 26th 2020; Issue No.: Revision 3

Approval expiry date: 27 October 2024

Uncontrolled if printed Page 71 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Pontoon Work Ltd

Modular Pontoon DWI 56/4/1309
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Pontoonworks: Pontoon solutions for working on clean water
sites
Issue Date: 2nd January 2018; Issue Number: 03
This product is approved for limited use during planned maintenance
and may not be permanently installed. If the proposed use will extend
beyond a 90 day period of use on any one occasion, then advice from
the DWI should be sought before installation and use. NOTE: It is the
responsibility of the water supplier to undertake a thorough risk
assessment of the proposed use, including fitness-for-purpose. Use of
this product during planned maintenance shall be in accordance with
the condition set out above.
Approval expiry date: 26 July 2023

Power Plastics Ltd

Power Plas ® BC850 Baffle Curtain DWI 56/4/1350
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: PowerPlas BC850 Baffle Curtain - For use in water for human
consumption
Issue No.: 1.0; Issue Date: February 2019
Approval expiry date: 9 October 2024

PWN Technologies
Suspended Ion Exchange (SIX) DWI 56/4/1171
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use (IFU) for the SIX® Technology by PWN
Technologies , Revision 1.4 Date of Issue: 05 October 2020

This approval does not include any ion exchange resins.

Approval expiry date: 13 October 2025

Sensor (UK) Ltd

Sensorline (Stainless steel) DWI 56/4/1066b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: SENSORLINE – PE GEOMEMBRANES (IFU VERSION 4.9)
Issue date 9 November 2015
Approval expiry date: 19 March 2023

Staptina Engineering Services Ltd

Staptina Bespoke stainless steel fabrications: Pipework, Baffles, Troughs,
Tanks, Support and Access systems DWI 56/4/567c
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: 24838IFU 12 June 2013
Approval expiry date: 31 March 2024

Uncontrolled if printed Page 72 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

SUEZ Water Technologies and Solutions Hungary Kft

Stainless Steel Products DWI 56/4/1371
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use Document for the Supply of Stainless Steel
Piping, Tanks and other Equipment for use in the Public Water Supply
in the UK
Issue Date: 24 June 2019; Issue No. UKDWI/SSP/Revision 0
Approval expiry date: 17 July 2024

Tema Engineering Limited

Stainless Steel Pipework, Tanks and Vessels for Water Use DWI 56/4/1376b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue No: 01; Issue Date: 25/07/2019
Approval expiry date: 6 October 2024

Veolia Water Technologies UK

Greca Lamella Plates DWI 56/4/309
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU Rev A
Approval expiry date: 14 March 2022
Package Actiflo and Multiflo DWI 56/4/770
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: IFU, VWT/ASMS/S4, Issue 1, Jan 2017
Approval expiry date: 26 April 2022

Vessco Engineering Ltd

Fabricator of Bespoke Stainless Steel Products: Pressure Vessels, Tanks
and Pipes DWI 56/4/1345b
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Issue 1, Rev 1: 24 January 2019
Approval expiry date: 20 February 2024

WEARS Australia
ResMix Vital DWI 56/4/1131
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Operation and maintenance Manual Resmix Vital Surface
Mounted Destratification System Version 2.1 Issue date 24
September 2019
Approval expiry date: 9 April 2024

Western Carbons
Stainless Steel Floor Plates, weirs, pipework and tanks DWI 56/4/1303
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Western Carbons Stainless Steel Products. Issue date:
November 2017; Issue number: Version 1.0
Approval expiry date: 18 February 2023

Uncontrolled if printed Page 73 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Wester Carbons Porous Block DWI 56/4/1297

Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Instructions for Use (IFU) - Western Carbons Porous Block Issue
Date: August 2017, Issue No: Version 1.0
Approval expiry date: 25 March 2023

Xylem Water Solutions Zelienople LLC

Leopold Ari Scour System DWI 56/4/1250
Conditions of Approval: Use of the product must be in accordance with the Instructions for
Use: Air Scour System AHP-IFU-00 Issue date: 12/13/16 Issue
number:R01
Approval expiry date: 5 March 2022

Uncontrolled if printed Page 74 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

INDEX BY PRODUCT NAME

Volute Dewatering Screw Press AMCON Europe s.r.o E.4 DWI 56/4/1144
3M Scotchkote Pipe Protection Liner 3M United Kingdom C.2.2 DWI 56/4/1037
2100
3M Scotchkote Pipe Renewal Liner 2400 3M United Kingdom C.2.2 DWI 56/4/1031
3M Scotchkote Rapid Setting Polymeric 3M United Kingdom C.2.3 DWI 56/4/1032
Lining 166L
8040-SBNF-DWI Membrane Elements Microdyn-Nadir US Inc D.1 DWI 56/4/1218
8040-SBUF-DWI Microdyn-Nadir US Inc D.1 DWI 56/4/1030
Absolute.Za*DWI SUEZ Water Technologies & D.1 DWI 56/4/1325
Solutions
Acothane DW Blue Axalta Coating Systems C.3.2 DWI 56/4/1059
Acothane DW Cream Axalta Coating Systems C.3.2 DWI 56/4/1052
Acothane LV Sealer Axalta Coating Systems C.3.2 DWI 56/4/1058
AFM Activated Filter Media Dryden Aqua Ltd A.10 DWI 56/4/382
Airophos 750PWG Airedale Chemical Company Ltd A.9 DWI 56/4/960
Akdolit® SLS45 Lhoist UK Ltd A.9 DWI 56/4/1392
Amazon SupaGard Cartridge Filters Amazon Filters Ltd D.1 DWI 56/4/702
Amazon SupaSpun II Cartridge Filters Amazon Filters Ltd D.1 DWI 56/4/702
Angus Wellmaster Flexible Rising Main Angus Flexible Pipelines B.2 DWI 56/4/1020
AquaCube Emergency Water Tank JFC Manufacturing Co. Ltd B.3.2 DWI 56/4/765
Aquaflex X-FLOW B.V. D.1 DWI 56/4/324
Aquaflex HP X-FLOW B.V. D.1 DWI 56/4/967
Aquaforce (with non-lead stabiliser) Wavin Ireland Ltd B.1.3 DWI 56/4/600
Aquastore Vitrium EN CST Industries Ltd E.1 DWI 56/4/621
Aquaurethane Extreme Line-X Protective coatings C.3.2 DWI 56/4/874
Aquron 2000 MG Solutions (UK) Ltd C.6 DWI 56/4/1291
Arlington 1000 Litre Bag-in-Box Combo Arlington Packaging (Rental) Ltd B.3.3 DWI 56/4/796
Liner
Atlantis Hydrotec - T&M Series Craley Group Ltd E.4 DWI 56/4/1346
Avista 505 Avista Technologies (UK) Ltd A.5 DWI 56/4/1321
AvistaClean MF 1000a Avista Technologies (UK) Ltd A.5 DWI 56/4/1327
Barr + Wray Colour/Organics Removal Barr + Wray Ltd A.3.1 DWI 56/4/1238
Ion Exchange Resin BW 141204
Barr + Wray Colour/Organics Removal Barr + Wray Ltd A.3.1 DWI 56/4/1239
Ion Exchange Resin BW 200613
Barr + Wray Colour/Organics Removal Barr + Wray Ltd A.3.1 DWI 56/4/1237
Ion Exchange Resin BW 341817

Uncontrolled if printed Page 75 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Barr + Wray Stainless Steel Media Filter Barr + Wray Ltd E.3 DWI
56/4/1234b
Barr + Wray Stainless Steel Media Filter Barr + Wray Ltd E.1 DWI
56/4/1234a
BioMate MBC2881 SUEZ Water Technologies & A.5 DWI 56/4/1276
Solutions
Bi-OROC Dyka S.A.S. B.1.3 DWI 56/4/1207
Black PE80 Polyethylene Pipes Polypipe Building Products B.1.1 DWI 56/4/968
Black PE80 Polyethylene Pipes Polypipe Building Products B.1.1 DWI 56/4/986
(ME3440)
Blue PE80 Polyethylene Pipes Polypipe Building Products B.1.1 DWI 56/4/970
Blue PE80 Polyethylene Pipes (PC002 Polypipe Building Products B.1.1 DWI 56/4/1120
50R698)
Blutop Saint-Gobain PAM UK Ltd B.1.12 DWI 56/4/823
Boode Waterwell Systems PVC Screen Boode UK Ltd B.2 DWI 56/4/958
and Casing
Bridges in-house fabricated stainless Bridges Electrical Engineering E.4 DWI
steel pipe spools and products Ltd 56/4/1268b
Bridges in-house fabricated stainless Bridges Electrical Engineering B.1.10 DWI
steel pipe spools and products Ltd 56/4/1268a
BSR/EPW/004 - Copon Hycote PWX BSR Pipeline Services Ltd B.1.9 DWI 56/4/772
C10 Module PCI Membranes D.1 DWI 56/4/234
CA202 membrane PCI Membranes D.1 DWI 56/4/76
Cementitious Coating 851 Grey Flexcrete Technologies Ltd C.5 DWI 56/4/1159
Cementitious Coating 851 White Flexcrete Technologies Ltd C.5 DWI 56/4/1160
CEMLINE STON Vandex International Ltd C.6 DWI 56/4/1095
CEMLINE UM1 Vandex International Ltd C.5 DWI 56/4/1099
CEMLINE BB-W Vandex International Ltd C.5 DWI 56/4/1093
CEMLINE CG Vandex International Ltd C.5 DWI 56/4/1094
Cemprotec 851F Flexcrete Technologies Ltd C.5 DWI 56/4/1340
CeraMac® Technology PWN Technologies D.1 DWI 56/4/1179
CF-DW Series cartridge filter housings Filtertec Systems Ltd D.2 DWI 56/4/1331
Cheetah range of Tanks & Towers Forbes Technology Ltd E.1 DWI 56/4/1292
Cheetah Tower Packings Forbes Technology Ltd E.4 DWI 56/4/711
Chlorine Dioxide generated by Xziox International Water Solutions Ltd A.7.3 DWI 56/4/998
Citric acid (food grade) Traditional Chemical A.7.1 DWI 56/1/106
Citric Acid 50% Solution Brenntag UK & Ireland A.5 DWI 56/4/1333
Clortec cell De Nora Water Technologies UK A.7.2 DWI 56/4/549
Services Ltd
Codeline RO Membrane Housing Pentair Water India Pvt Ltd D.2 DWI 56/4/288
Codeline 80S Series (Coded Vessels)

Uncontrolled if printed Page 76 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Codeline RO Membrane Housing Pentair Water India Pvt Ltd D.2 DWI 56/4/288
Codeline 80S Series (Non-coded
Vessels)
Conbextra Bedding Mortar Fosroc Ltd C.6 DWI 56/4/1271
Constant Chlor Plus Briquettes Arch Chemicals Ltd A.9 DWI 56/4/1241
CP Polytec 100 Cork Plastics B.1.1 DWI 56/4/1351
CP Polytec PE80E Cork Plastics B.1.1 DWI 56/4/1187
CPE Pressure Vessels-304L and 316L CPE Pressure Vessels E.3 DWI 56/4/1135
Stainless Steel
DE Stainless Steel Systems Dustacco Engineering Ltd B.1.10 DWI 56/4/647
Deltapor MW and MWA Filter Cartridges Envirogen Group D.1 DWI 56/4/1274
Durapipe ABS Pipe Type S Durapipe UK B.1.4 DWI 56/4/660
Durapipe Grey PVC-U Pipe NGS Durapipe UK B.1.3 DWI 56/4/937
Durapipe PREMIUM PVC-U pipe Durapipe UK B.1.3 DWI 56/4/1226
DVF Media Filters Amiad Water Systems UK Ltd D.4 DWI 56/4/1249
Dyka Grey PVC-U Pipe NGS Dyka B.V. B.1.3 DWI 56/4/637
Easychlorgen 280 – 2200 Electrolysis Lutz-Jesco GmbH A.7.2 DWI 56/4/1369
system for on-site hypochlorite
generation
EFH/SFH/PFH (Cartridge Housings) Fileder Filter Systems D.2 DWI 56/4/848
egeclean (+) Egeplast International GmbH B.1.1 DWI 56/4/1157
egeclean 9010 Egeplast International GmbH B.1.1 DWI 56/4/1158
egeclean PE100 Egeplast International GmbH B.1.1 DWI 56/4/1156
egelen PE 100 Blue Egeplast International GmbH B.1.1 DWI 56/4/436
egelen PE100 Black Egeplast International GmbH B.1.1 DWI 56/4/436
egeplast 9010 Egeplast International GmbH B.1.1 DWI 56/4/1065
egeplast egelen (+) Plus Pipe Egeplast International GmbH B.1.1 DWI 56/4/1111
Egeplast SLA Barrier Pipes Egeplast International GmbH B.1.2 DWI 56/4/1109
Electrofresh Ductile Iron Pipe Electrosteel Castings Ltd B.1.7.1 DWI 56/4/992
Electrofresh Plus Pipes Electrosteel Castings Ltd B.1.7.2 DWI 56/4/537
Eliquo Hydrok Filter Housing Tank Eliquo Hydrok D.2 DWI 56/4/1386
Emergency Drinking Water Bowsers Trailer Engineering Ltd B.3.2 DWI 56/4/707
Enduratank Enduramaxx Ltd B.3.2 DWI 56/4/1242
Envirogen CF Filter Housing Envirogen Group D.2 DWI 56/4/1257
ePipe UK Pipe Restoration Technologies C.2.3 DWI 56/4/995
LLC
Erciyas Steel Water Pipe – Cement Lined Erciyas Celik Boru Sanayi A.S B.1.7.1 DWI 56/4/1047
ES404 membrane PCI Membranes D.1 DWI 56/4/215
European Pipeline Group Svobodny European Pipeline Group B.1.7.1 DWI 56/4/1114
Sokol Ductile Iron Pipe

Uncontrolled if printed Page 77 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Excel White GPS B.1.1 DWI 56/4/1269

Expansion Joint Flex EJ Ltd E.4 DWI 56/4/1382
Fabricated mild steel pipework coated UTS Engineering Ltd B.1.9 DWI 56/4/1324
with Jotaguard VA5001
Fabricated mild steel pipework coated UTS Engineering Ltd B.1.9 DWI 56/4/1085
with Scotchkote 162pwx
Fabricator of Bespoke Stainless Steel Vessco Engineering Ltd B.1.10 DWU
Products: Pressur Vessels, Tanks and 56/4/1345a
Pipes
Fabricator of Bespoke Stainless Steel Vessco Engineering Ltd E.4 DWI
Products: Pressure Vessels, Tanks 56/4/1345b
and Pipes
Fastfill Flexcrete Technologies Ltd C.6 DWI 56/4/1162
Filtec "Selkie" Stainless Steel Products Filtec Water Services Ltd E.4 DWI
56/4/1396c
Filtec "Selkie" Stainless Steel Products Filtec Water Services Ltd E.1 DWI
56/4/1396b
Filtec "Selkie" Stainless Steel Products Filtec Water Services Ltd B.1.10 DWI
56/4/1396a
Flagon Geo P/AT Flag S.p.a C.4 DWI 56/4/856
Flocon 135 BWA Water Additives UK Ltd A.5 DWI 56/4/839
Fusion ® V1100 Permastore Ltd E.1 DWI 56/4/1214
Genesol 38 Genesys International Ltd A.5 DWI 56/4/664
Genesol 40 Genesys International Ltd A.5 DWI 56/4/665
Genesol 61 Genesys International Ltd A.5 DWI 56/4/1205
Genesol 704 Genesys International Ltd A.5 DWI 56/4/1319
Genesys CAS Genesys International Ltd A.5 DWI 56/4/1253
Genesys LF Genesys International Ltd A.5 DWI 56/4/495
Genesys LF60 Genesys International Ltd A.5 DWI 56/4/783
Genesys LS Genesys International Ltd A.5 DWI 56/4/781
Genesys SI Genesys International Ltd A.5 DWI 56/4/593
Genesys SW Genesys International Ltd A.5 DWI 56/4/524
GEROthen® COEX Gerodur MPM B.1.1 DWI 56/4/1370
Kunststoffverarbeitung GmbH
& Co. KG
Gerothern PE100 Polyethylene Pipes EBERO Pipe Systems Ltd B.1.1 DWI 56/4/1115
GF ABS pressure pipe George Fischer Sales Ltd B.1.4 DWI 56/4/753
GF DEKADUR PVC-U pressure pipe George Fischer Sales Ltd B.1.3 DWI 56/4/1231
GF PE100 Black Pipe George Fischer Sales Ltd B.1.1 DWI 56/4/957
GF PVC-U Inch Pipe George Fischer Sales Ltd B.1.3 DWI 56/4/1235
GPS B Light Blue Polyethylene Pipe GPS B.1.1 DWI 56/4/242

Uncontrolled if printed Page 78 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

GPS Excel (Black) GPS B.1.1 DWI 56/4/851

GPS Excel (Blue) GPS B.1.1 DWI 56/4/850
GPS Excel (Black) Type F GPS B.1.1 DWI 56/4/961
GPS Excel 3c (Black) GPS B.1.1 DWI 56/4/871
GPS Excel 3c (Blue) GPS B.1.1 DWI 56/4/853
GPS Excel CR GPS B.1.1 DWI 56/4/946
GPS Excel NB GPS B.1.1 DWI 56/4/1026
GPS Excel NB Type V GPS B.1.1 DWI 56/4/1050
GPS N Black Polyethylene Pipe GPS B.1.1 DWI 56/4/1260
GPS N Blue PE80 Pipe GPS B.1.1 DWI 56/4/651
GPS Protecta-Line GPS B.1.2 DWI 56/4/872
GPS Protecta-Line 3c GPS B.1.2 DWI 56/4/873
Greca Lamella Plates Veolia Water Technologies UK E.4 DWI 56/4/309
Guardsman GT190 Antiscalant for Kobell Fluid Technology Ltd A.5 DWI 56/4/1123
Membrane Systems
HFW 1000 X-FLOW B.V. D.1 DWI 56/4/1139
High Performance SC100 Dark Blue Pipe Radius Systems Ltd B.1.1 DWI 56/4/939
PE100 pipe including Clean Pipe
HYDRAcap Hydranautics D.1 DWI 56/4/689
Hydrochoc Butyl Bladder Surge Vessel Charlatte Reservoirs E.3 DWI 56/4/1016
Hypersperse MDC 704i SUEZ Water Technologies & A.5 DWI 56/4/1302
Solutions
Hypersperse MDC 711 SUEZ Water Technologies & A.5 DWI 56/4/1300
Solutions
Hypersperse MDC 714 SUEZ Water Technologies & A.5 DWI 56/4/1301
Solutions
Hypersperse MSI310 SUEZ Water Technologies & A.5 DWI 56/4/1311
Solutions
ICL - Citric Acid Solution Industrial Chemicals Ltd A.5 DWI 56/4/1342
Intercrete 4800 International Paint Ltd C.6 DWI 56/4/1403
Intercrete 4800WS International Paint Ltd C.6 DWI 56/4/1408
Intercrete 4802 International Paint Ltd C.6 DWI 56/4/1055
Intercrete 4807 International Paint Ltd C.6 DWI 56/4/1404
Intercrete 4820 International Paint Ltd C.5 DWI 56/4/1054
Intercrete 4841 International Paint Ltd C.5 DWI 56/4/1053
Intercrete 4871 International Paint Ltd C.6 DWI 56/4/1056
Ion exchange colour removal system Barr + Wray Ltd A.3.2 DWI 56/4/1176
IPF and NPF model of Dissolved Air Nijhuis Water Technology B.V. E.4 DWI 56/4/620
Flotation units

Uncontrolled if printed Page 79 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

IPSSSPW01 Stainless Steel Pipework Equipdata Trading B.1.10 DWI 56/4/1316

and Fabrications
Isofusion (vitreous enamelled tank) Permastore Ltd E.1 DWI 56/4/594
IXL Process Ionex SG Ltd A.3.2 DWI 56/4/467
Jacopa Ltd / Nordic Water Lamella Plate Jacopa Ltd E.4 DWI 56/4/622
Separators
Jaguar Range of Storage & Process Forbes Technology Ltd E.1 DWI 56/4/1210
Tanks & Towers
JKF 304 and 316 Stainless Steel Tanks J.K Fabrications Limited E.1 DWI 56/4/732
Johnson Screen, Casing & johnson Riser Aqseptence Group SAS B.2 DWI 56/4/653
Pipe and Accessories
JSAW-JAL-11A Jindal Saw Ltd B.1.7.1 DWI 56/4/935
JSAW-JAL-11B Jindal Saw Ltd B.1.7.2 DWI 56/4/936
JSAW-JAL-1A Jindal Saw Ltd B.1.7.1 DWI 56/4/933
JSAW-JAL-1B Jindal Saw Ltd B.1.7.2 DWI 56/4/934
JSGL-JAL-1A JINDAL SAW GULF LLC B.1.7.1 DWI 56/4/1122
K Filter Floor Black & Veatch E.2 DWI 56/4/833
Kalic HSD Tarmac Lime & Cement A.9 DWI 56/4/1206
KLEEN MCT515E SUEZ Water Technologies & A.5 DWI 56/4/1273
Solutions
Kleen MTC405 SUEZ Water Technologies & A.5 DWI 56/4/1289
Solutions
Kleen* MCT103 SUEZ Water Technologies & A.5 DWI 56/4/1008
Solutions
Kleen* MCT524 SUEZ Water Technologies & A.5 DWI 56/4/1007
Solutions
Kleen* MCT882 SUEZ Water Technologies & A.5 DWI 56/4/1010
Solutions
Lamella Separator Package (LSF) Colloide Engineering Systems E.4 DWI 56/4/1172
Ltd
Leinster Range of Thermoplastic Tanks Silotank (Digestors, Silos & E.1 DWI 56/4/498
Tanks) Ltd
Leinster Range of Towers Silotank (Digestors, Silos & E.1 DWI 56/4/498
Tanks) Ltd
Leopold Ari Scour System Xylem Water Solutions E.4 DWI 56/4/1250
Zelienople LLC
Leopold Type S Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1079
1000 Media Retainer Zelienople LLC
Leopold Type S Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1078
200 Media Retainer Zelienople LLC
Leopold Type S Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/371
Cap Zelienople LLC

Uncontrolled if printed Page 80 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Leopold Type SL Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1079
1000 Media Retainer Zelienople LLC
Leopold Type SL Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1078
200 Media Retainer Zelienople LLC
Leopold Type SL Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/371
Cap Zelienople LLC
Leopold Type XA Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1105
1000 Media Retainer Zelienople LLC
Leopold Type XA Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1105
200 Media Retainer Zelienople LLC
Leopold Type XA Underdrain and I.M.S. Xylem Water Solutions E.2 DWI 56/4/1105
Cap Zelienople LLC
Lewatit S 5128 Lanxess Deutschland GmbH A.3.1 DWI 56/4/1193
Lion Range of Tanks & Towers Forbes Technology Ltd E.1 DWI 56/4/1293
Lorem ipsum dolor sit amet, consectetuer Traditional Chemical ).99.99.99 DWI 56/4/0000
adipiscing elit. Aenean commodo
ligula eget dolor. Aenean massa. Cum
sociis natoque penatibus et magnis
dis parturient montes, nascetur
ridiculus mus. Donec quam felis,
ultricies nec, pellentesque eu, pretium
quis,
Macropoxy P300 Sherwin-Williams Protective and C.3.1 DWI 56/4/253
Marine Coatings
Magnafloc LT20 Solenis UK Industries Ltd A.1.2 DWI 56/4/885
Magnafloc LT22S-DWI Solenis UK Industries Ltd A.1.2 DWI 56/4/884
Magnafloc LT25 Solenis UK Industries Ltd A.1.2 DWI 56/4/886
Magnafloc LT27 Solenis UK Industries Ltd A.1.2 DWI 56/4/887
Magnesium sulphate Traditional Chemical A.7.1 DWI 56/1/106
Magnesium Sulphate Heptahydrate 40% Brenntag UK & Ireland A.9 DWI 56/4/1334
MasterEmaco S420 with MasterSeal 600 BASF plc Construction C.6 DWI 56/4/1064
Chemicals (UK) Ltd
MasterSeal 581 BASF plc Construction C.5 DWI 56/4/1227
Chemicals (UK) Ltd
MasterSeal 581 with MasterSeal 600 BASF plc Construction C.5 DWI 56/4/1103
Chemicals (UK) Ltd
MasterSeal 586 with MasterSeal 600 BASF plc Construction C.5 DWI 56/4/86
Chemicals (UK) Ltd
MasterSeal 588 BASF plc Construction C.5 DWI 56/4/1128
Chemicals (UK) Ltd
MasterSeal 930 and MasterSeal 933 BASF plc Construction C.6 DWI 56/4/144
Chemicals (UK) Ltd
Masterseal M 808 BASF plc Construction C.3.2 DWI
Chemicals (UK) Ltd 56/4/1080a

Uncontrolled if printed Page 81 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Masterseal M 808 additional light grey BASF plc Construction C.3.2 DWI
colour Chemicals (UK) Ltd 56/4/1080b
Memcor CMF- S S10V Range of DuPont Water Solutions D.1 DWI 56/4/973
Microfiltration submodules
(submerged PVDF Membranes)
Memcor CMF-L L10N DuPont Water Solutions D.1 DWI 56/4/1254
Memcor CMF-L L10V Range of DuPont Water Solutions D.1 DWI 56/4/977
Microfiltration Submodules (PVDF
Membranes)
Memcor CMF-L L20N DuPont Water Solutions D.1 DWI 56/4/1255
Memcor CMF-L L20V Range of DuPont Water Solutions D.1 DWI 56/4/978
Microfiltration Submodules (PVDF
Membranes)
Memcor CMF-L L40N DuPont Water Solutions D.1 DWI 56/4/1305
Memcor CMF-M10C Continuous DuPont Water Solutions D.1 DWI 56/4/975
Microfiltration Module (Polypropylene
Membranes)
Memcor CMF-S S10N DuPont Water Solutions D.1 DWI 56/4/1256
Memcor CMF-S S10T Microfiltration DuPont Water Solutions D.1 DWI 56/4/976
Submodule (submerged
Polypropylene Membranes)
MIEX DOC Resin Ixom Operations Pty Ltd A.3.1 DWI 56/4/550
MIEX Gold Ixom Operations Pty Ltd A.3.1 DWI 56/4/1140
MK IV EDR Water Treatment System Suez Water Technologies & D.3 DWI 56/4/480
Solutions (USA Inc)
Modular Pontoon Pontoon Work Ltd E.4 DWI 56/4/1309
Monolevel 844SP Flexcrete Technologies Ltd C.5 DWI 56/4/1161
Monomix Flexcrete Technologies Ltd C.6 DWI 56/4/1163
Monomix WS Flexcrete Technologies Ltd C.6 DWI 56/4/397
Monostore SST - Recognised Grade Monostore Ltd E.1 DWI 56/4/1374
Tanks
MULTIBLOCK® Media Retaining Gravity WesTech Engineering Inc E.2 DWI 56/4/1312
Filter Underdrain
NATCEM 35 Natural Cement Distribution Ltd C.6 DWI 56/4/1090
NATCEM AC Natural Cement Distribution Ltd C.6 DWI 56/4/840
NATCEM D Natural Cement Distribution Ltd C.6 DWI 56/4/1216
NATCEM DW Natural Cement Distribution Ltd C.6 DWI 56/4/1049
Neumo Stainless Steel Tube and Fittings Neumo UK Ltd B.1.10 DWI 56/4/1167
Noksel Steel Water Pipe – Coated with Noksel Steel Pipe Co Inc B.1.9 DWI 56/4/1192
Thixo 468
OSTP Stainless Steel pipe and fittings of OSTP B.1.10 DWI 56/4/516
12mm bore or greater.

Uncontrolled if printed Page 82 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Oxiperm ISIA (with U-type reactor) Grundfos Holdings A/S A.7.3 DWI 56/4/1236
Package Actiflo and Multiflo Veolia Water Technologies UK E.4 DWI 56/4/770
Pall GF Plus Filter Units, Type MWH27 Pall Corporation D.1 Dwi 56/4/1336
Pall Microza UNA-620C microfiltration Pall International Sarl D.1 DWI 56/4/795
module
PaM Natural Pipeline Components Saint-Gobain PAM UK Ltd B.1.9 DWI 56/4/618
PAX Water Monopod Mixers (PWM PAX Water Technologies Inc E.4 DWI 56/4/1335
100/150/250) and PAX Water Mixer
(PWM400/500/600)
PE100 High Performance Profuse Pipe Radius Systems Ltd B.1.1 DWI 56/4/943
including Factory Sealed
Peak Pipe Systems Peak Pipe Systems B.1.1 DWI 56/4/548
Penecrete Mortar Penetron UK Ltd C.6 DWI 56/4/1130
Penectron Crystalline Waterproof Coating Penetron UK Ltd C.6 DWI 56/4/1137
PEXGOL GOLAN Plastic Products Ltd B.2 DWU 56/4/1259
Pile Cloth Media Filter (PCMF) DW2/10 - Mecana Umwilttechnik GmbH D.1 DWI 56/4/1215
DW27/135
Pipes and fittings lined with Eurokote 468 Northpoint Ltd B.1.9 DWI 56/4/1209
Thixo
Pipes and Fittings lined with Jotaguard Northpoint Ltd B.1.9 DWI 56/4/1304
VA 5001
Pipes and Fittings lined with Resicoat R4- Orrmac Coatings Limited B.1.9 DWI 56/4/771
FB HKC71R
Pipes Lined with Resicoat R4-FB Freeflow Pipesystems Ltd B.1.9 DWI 56/4/817
HKC71R
Pipes lined with Scotchkote 162PWX Orrmac Coatings Limited B.1.9 DWI 56/4/985
Pipes, Fittings and Steelwork coated with Northpoint Ltd B.1.9 DWI 56/4/659
Resicoat R4-FB HKC71R
Plasmor E and U Blocks Plasmor Ltd E.2 DWI 56/4/988
Polyguard: Polypipe Building Products B.1.2 DWI 56/4/857
Polyethylene/Aluminium/Polyethylene
barrier pipes
Polyguard: Polypipe Building Products B.1.2 DWI 56/4/1076
Polyethylene/Aluminium/Polyethylene
barrier pipes (ME3444)
Polypipe Black PE100 Polyethylene Polypipe Ltd B.1.1 DWI 56/4/1343
Pipes (TUB121N3000)
Polypipe Blue PE100 Polyethylene Pipes Polypipe Building Products B.1.1 DWI 56/4/1296
(TUB124N 2025)
Power Plas ® BC850 Baffle Curtain Power Plastics Ltd E.4 DWI 56/4/1350
PowerPlas ® TL850 Tank Liner Power Plastics Ltd C.4 DWI 56/4/1385
Powerrun fabricated stainless steel Powerrun Pipe-Mech Ltd B.1.10 DWI 56/4/769
pipework

Uncontrolled if printed Page 83 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Premcrete Hydroseal FX FIS Products C.5 DWI 56/4/1356

Premcrete Teknocem HB50 FIS Products C.6 DWI 56/4/1357
Premcrete Teknocem Rapid FIS Products C.6 DWI 56/4/1358
Premcrete Teknolevel FS FIS Products C.5 DWI 56/4/1359
Premcrete Teknoprime 841 FIS Products C.6 DWI 56/4/1360
Premcrete Tie Hole Sealer FIS Products C.6 DWI 56/4/1361
PRESSURE FILTRATION KIT DF DYNAMlK FlLTR Nocoń D.4 DWI 56/4/1272
FP/FDN 800÷3 500 iWspólnicy Spółka Jawna
Pressure Vessels A J Metal Products Ltd E.3 DWI 56/4/1383
Purafloc TM 001 JFI Limited A.9 DWI 56/4/1355
Purafloc TM 001 Clinty Chemicals Limited A.9 DWI 56/4/1378
Puresol Tarmac Cement and Lime A.9 DWI 56/4/1147
Limited
Puriton Pipe Radius Systems Ltd B.1.2 DWI 56/4/1112
Purolite A520E nitrate selective anion Purolite International Ltd A.3.1 DWI 56/4/11
exchange resin
PVC Screens, Casings, Fittings and Stuwa-Konrad Stukerjurgen B.2 DWI 56/4/1061
Accessories GmbH
Q Pipe System ABC Stainless Steel Ltd B.1.10 DWI 56/4/542a
Qual-plast HDPE Pipe Pipelife Ireland Limited B.1.1 DWI 56/4/997
Qual-plast MDPE Pipe Pipelife Ireland Limited B.1.1 DWI 56/4/240
QualPLAST Polyethylene MDPE co- Pipelife Ireland Limited B.1.1 DWI 56/4/1282
extruded pipe
Quantum Pressure Vessels- 304L Quantum Engineering E.3 DWI 56/4/1132
Developments Ltd
Quantum Pressure Vessels- 316L Quantum Engineering E.3 DWI 56/4/1133
Developments Ltd
Renderoc Plug 20 Fosroc Ltd C.6 DWI 56/4/297
RENO 100 Idrotherm 2000 spa B.1.1 DWI 56/4/1168
Resinex KW-H Jacobi Carbons A.3.1 DWI 56/4/1151
ResMix Vital WEARS Australia E.4 DWI 56/4/1131
Rilsan Nylon Green Coated Pipes and Leyfos Plastics Limited B.1.8 DWI 56/4/615
Fittings
RoCide DB20 Avista Technologies (UK) Ltd A.5 DWI 56/4/964
RoClean L403 Avista Technologies (UK) Ltd A.5 DWI 56/4/855
RoClean P111 Avista Technologies (UK) Ltd A.5 DWI 56/4/737
RoClean P303 Avista Technologies (UK) Ltd A.5 DWI 56/4/746
Safe 10 Centraltubi SPA B.1.1 DWI 56/4/1366
SBH and PBF Stainless Steel Bag Fileder Filter Systems D.2 DWI 56/4/848
Housing

Uncontrolled if printed Page 84 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

SC100 (PE100) XL large diameter / Radius Systems Ltd B.1.1 DWI 56/4/1146
heavy wall dark blue potable water
pipe
SC80 Service Pipe Radius Systems Ltd B.1.1 DWI 56/4/941
SEAQUEST Aqua Smart Inc. A.9 DWI 56/4/202
Sensorline Sensor (UK) Ltd C.4 DWI
56/4/1066a
Sensorline (Stainless steel) Sensor (UK) Ltd E.4 DWI
56/4/1066b
SFH and PFH Stainless Steel Filter Fileder Filter Systems D.2 DWI 56/4/848
Housing
SFH PFH SSS Filter housing Evoqua Water Technologies Ltd D.2 DWI 56/4/1191
Shotcrete 513 Natural Cement Distribution Ltd C.6 DWI 56/4/1089
Sika Monotop 610/615 Concrete Repair Sika Ltd C.6 DWI 56/4/834
System
Sikadur Combiflex SG jointing system Sika Ltd C.6 DWI 56/4/94
using Sikadur 31 DW
Sikadur Combiflex SG jointing system, Sika Ltd C.6 DWI 56/4/1124
using Sikadur 31 DW Rapid
Sikagard 62 Sika Ltd C.3.1 DWI 56/4/197
Silver Bullets 1000 BioBullets Ltd A.9 DWI 56/4/852
Silver Bullets 2000 BioBullets Ltd A.9 DWI 56/4/1000
Simona PE100 Pressure Pipe Black Simona UK Ltd B.1.1 DWI 56/4/875
Single and Multiple Cartridge & Bag Filter Amazon Filters Ltd D.2 DWI 56/4/879
Housings and Interconnecting
pipework
Sirofloc Magnetite TM M-10 Northern Ireland Water A.1.3 DWI 56/4/1338
Snap-Tite TE Range – Blue Hose AAH Europe Hose Company Ltd B.3.1 DWI 56/4/62
(T/A Snap-tite)
Sodium Hypochlorite generated by Gaffey Technical Services Ltd A.7.2 DWI 56/4/1341
Hyprolyser Electrochlorination System
Sodium Hypochlorite generated by Danish Clean Water A/S A.7.2 DWI 56/4/1298
Neuthox
Sodium Hypochlorite generated by Danish Clean Water A/S A.7.2 DWI 56/4/1315
Neuthox T10/15
Sodium Hypochlorite generated by Danish Clean Water A/S A.7.2 DWI 56/4/1318
Neuthox T20
Sodium Hypochorite generated by Grundfos Holdings A/S A.7.2 DWI 56/4/864
Selcoperm
Stainless Steel ANSI Metric ISO Pipe, Blackburns Metal Ltd B.1.10 DWI 56/4/1224
Stainless Steel ANSI Metric ISO Tube,
Stainless Steel ANSI Metric ISO
Fittings

Uncontrolled if printed Page 85 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Stainless Steel Floor Plates, weirs, Western Carbons E.4 DWI 56/4/1303
pipework and tanks
Stainless Steel Grade 316L Potable Powerrun Pipe-Mech Ltd E.1 DWI 56/4/611
Water Reservoir Tanks
Stainless Steel Metric ISO & ANSI DH Stainless Ltd B.1.10 DWI 56/4/773
welded pipe and fittings
Stainless Steel Pipe | Stainless Steel Righton and Blackburns Ltd B.1.10 DWI 56/4/1221
Tube | Stainless Steel Fittings |
Material grades 304/304L, 316/316L,
1.4301/1.4307, 1.4401/1.4404
Stainless Steel pipes, Stainless Steel Righton and Blackburns Ltd B.1.10 DWI 56/4/1221
Tube, Stainless Steel Fittings
Stainless Steel Pipes, Tubes, Fittings and Yorkshire Stainless Ltd B.1.10 DWI 56/4/1368
Flanges
Stainless Steel Pipework Alpha Plus Ltd B.1.10 DWI 56/4/692
Stainless Steel Pipework & Fittings - George Green (Keighley) Ltd B.1.10 DWI 56/4/699
Flanged/Screwed - All diameters &
Grades
Stainless Steel Pipework and AJ Engineering and Construction E.4 DWI
Fabrications Services Ltd 56/4/1220b
Stainless Steel Pipework and AJ Engineering and Construction B.1.10 DWI
Fabrications Services Ltd 56/4/1220a
Stainless Steel Pipework and Berry & Escott Engineering E.1 DWI
Fabrications 56/4/1362a
Stainless Steel Pipework and Berry & Escott Engineering B.1.10 DWI 56/4/1362
Fabrications
Stainless Steel Pipework, Tanks and Tema Engineering Limited E.4 DWI
Vessels for Water Use 56/4/1376b
Stainless Steel Pipework, Tanks and Tema Engineering Limited B.1.10 DWI
Vessels for Water Use 56/4/1376a
Stainless steel process pipework systems Ross-shire Engineering Ltd B.1.10 DWI 56/4/1034
Stainless Steel Products SUEZ Water Technologies and E.4 DWI 56/4/1371
Solutions Hungary Kft
Stainless Steel Screens, Casings, Fittings Stuwa-Konrad Stukerjurgen B.2 DWI 56/4/1060
and Accessories GmbH
Stainless Steel Tanks & Pipework EPS Group E.1 DWI 56/4/1267
Stainless Steel Tanks and Launders Allied Storage Tank Ltd E.1 DWI 56/4/1258
Stainless Steel Tanks and Pipework Specialist Welding Services Ltd B.1.10 DWI 56/4/1367
Stainless Steel Tube, Stainless Steel pipe Amari Metals Ltd B.1.10 DWI 56/4/738
Stainless Steel Tubings and Fittings BSS Industrial B.1.10 DWI 56/4/1017
Stainless Steel Water Tanks Sayers Road Tankers Ltd E.1 DWI 56/4/1028
Stainless Steel Water Tanks Ross-shire Engineering Ltd E.1 DWI 56/4/1381
Stanton Bonna Concrete Pressure Pipe Stanton Bonna Concrete Limited B.1.7.1 DWI 56/4/1375

Uncontrolled if printed Page 86 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Staptina Bespoke stainless steel Staptina Engineering Services B.1.10 DWI 56/4/567a
fabrications: Pipework, Baffles, Ltd
Troughs, Tanks, Support and Access
systems
Staptina Bespoke stainless steel Staptina Engineering Services E.1 DWI 56/4/567b
fabrications: Pipework, Baffles, Ltd
Troughs, Tanks, Support and Access
systems
Staptina Bespoke stainless steel Staptina Engineering Services E.4 DWI 56/4/567c
fabrications: Pipework, Baffles, Ltd
Troughs, Tanks, Support and Access
systems
Steel pipe coated with Eurokote 468 BAIKA Steel Tubular Systems B.1.9 DWI 56/4/1203
Thixo SL
Steel Reinforcement Protector 841 Flexcrete Technologies Ltd C.6 DWI 56/4/1164
Storage, process tanks and vessels ABC Stainless Steel Ltd E.1 DWI 56/4/542b
STUWA Stainless Steel Riser Pipes Stuwa-Konrad Stukerjurgen B.2 DWI 56/4/1077
GmbH
Subcoil Radius Subterra – a part of B.1.1 DWI 56/4/461
RadiusPlus Ltd
Subcote 173/90 Radius Subterra – a part of C.2.1 WS 34/1/124a
RadiusPlus Ltd
Subcote 173/90 Radius Subterra – a part of C.3.1 WS 34/1/124b
RadiusPlus Ltd
Subcote FLP II Radius Subterra – a part of C.3.2 DWI
RadiusPlus Ltd 56/4/1286b
Subcote FLP II Radius Subterra – a part of C.2.2 DWI 56/4/1286
RadiusPlus Ltd
Super Aquaduct Angus Flexible Pipelines B.3.1 DWI 56/4/1005
Suspended Ion Exchange (SIX) PWN Technologies E.4 DWI 56/4/1171
System Cement Mortar Lined Ductile Iron Superior Pipeline Products Ltd B.1.7.1 DWI 56/4/990
Pipe
System CL Saint-Gobain PAM UK Ltd B.1.7.1 DWI 56/4/283
System CL Saint-Gobain PAM UK Ltd B.1.11 DWI 56/4/283
System XL Saint-Gobain PAM UK Ltd B.1.7.2 DWI 56/4/1317
System XL Saint-Gobain PAM UK Ltd B.1.11 DWI 56/4/1317
Tanks and associated Pipework, Weir Homer Burgess Ltd E.4 DWI
Plates and Baffle Plates manufactured 56/4/1107c
from Stainless steel suitable for use
with drinking water
Tanks and associated Pipework, Weir Homer Burgess Ltd E.1 DWI
Plates and Baffle Plates manufactured 56/4/1107b
from Stainless steel suitable for use
with drinking water

Uncontrolled if printed Page 87 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Tanks and associated Pipework, Weir Homer Burgess Ltd B.1.10 DWI
Plates and Baffle Plates manufactured 56/4/1107a
from Stainless steel suitable for use
with drinking water
Tetra LP Block System De Nora Water Technologies UK E.2 DWI 56/4/522
Services Ltd
Thycal Industrial Chemicals Ltd A.9 DWI 56/4/1025
Tiefill Flexcrete Technologies Ltd C.6 DWI 56/4/1287
TOM PVC-O Pipe Molecor Tecnología SL B.1.3 DWI 56/4/1057
TP Chlor Brenntag UK & Ireland A.9 DWI 56/4/979
TP Chlor plus Brenntag UK & Ireland A.9 DWI 56/4/1190
Trifusion ® Permastore Ltd E.1 DWI 56/4/1213
TUBEdek FS41.50/84 PP ENEXIO 2H Water Technologies E.4 DWI 56/4/878
Ltd
Ultrafiltration element ZW700B- SUEZ Water Technologies & D.1 DWI 56/4/1125
8060/UF10/7B/R/0.8/40 Solutions
Ultrafiltration element ZW700B- SUEZ Water Technologies & D.1 DWI 56/4/1126
8060/UF10/7B/X/0.8/40 Solutions
Ultralox 40 B&V Water treatment A.9 DWI 56/4/1074
Unlined 316 & 316L Stainless Steel Ocean Kinetics Ltd E.1 DWI
Tanks and Pipework 56/4/1395b
Unlined 316 & 316L Stainless Steel Ocean Kinetics Ltd B.1.10 DWI
Tanks and Pipework 56/4/1395a
Uratop PVC-O Adequa Adequa WS S.L.U B.1.3 DWI 56/4/1266
VANDEX BB 75 Vandex International Ltd C.5 DWI 56/4/1092
Vandex Plug Vandex International Ltd C.6 DWI 56/4/1096
VANDEX PREMIX Vandex International Ltd C.5 DWI 56/4/1097
VANDEX SUPER Vandex International Ltd C.5 DWI 56/4/1098
Velocitek OVF Filter Vessel Hydro-Gen Engineering Ltd D.4 DWI 56/4/1400
Vitec 3000 Avista Technologies (UK) Ltd A.5 DWI 56/4/457
Vitec 4000 Avista Technologies (UK) Ltd A.5 DWI 56/4/582
Vitec 5000 Avista Technologies (UK) Ltd A.5 DWI 56/4/458
Vitec 7000 Avista Technologies (UK) Ltd A.5 DWI 56/4/801
Vitec 7000a Avista Technologies (UK) Ltd A.5 DWI 56/4/869
Wallace and Tiernan OSEC ® Evoqua Water Technologies Ltd A.7.2 DWI 56/4/775
Water Pipe Lining Aqualiner Ltd C.1 DWI 56/4/910
Waterstop Natural Cement Distribution Ltd C.6 DWI 56/4/1217
Wavistrong Series Future Pipe Industries B.V B.1.6 DWI 56/4/656
Weholite Pipe and Panels Asset International Ltd B.1.1 DWI 56/4/513a
Weholite Pipe and Panels Asset International Ltd E.1 DWI 56/4/513b

Uncontrolled if printed Page 88 of 89 Issue date: 19 November 2020

List of approved products for use in public water supply in the United Kingdom

Wester Carbons Porous Block Western Carbons E.4 DWI 56/4/1297

Whale Drinking Water Bowser Whale Tankers Ltd B.3.2 DWI 56/4/662
WTP RO 411 Water Treatment Products A.5 DWI 56/4/821
Limited
WTP RO 413 Water Treatment Products A.5 DWI 56/4/822
Limited
XIGA HP X-FLOW B.V. D.1 DWI 56/4/1023
Xypex Admix C-1000 NF Xypex (UK) LLP C.6 DWI 56/4/1263
Xypex Admix C-500 NF Xypex (UK) LLP C.6 DWI 56/4/1244
Xypex Concentrate Xypex (UK) LLP C.5 DWI 56/4/1261
Xypex Modified Xypex (UK) LLP C.5 DWI 56/4/1262
Xypex Patch'n Plug Xypex (UK) LLP C.6 DWI 56/4/1100
ZeeWeed ® 700B-9060 Membrane SUEZ Water Technologies and D.1 DWI 56/4/1349
Module Solutions Hungary Kft
ZeeWeed 1000 V4 SUEZ Water Technologies and D.1 DWI 56/4/1177
Solutions Hungary Kft
ZeeWeed 1500 Series SUEZ Water Technologies and D.1 DWI 56/4/1013
Solutions Hungary Kft
ZeeWeed 500c, Membrane Filtration SUEZ Water Technologies & D.1 DWI 56/4/628
Module Solutions
ZeeWeed 500d (340)Membrane Filtration SUEZ Water Technologies & D.1 DWI 56/4/835
Module Solutions
ZeeWeed 500d (440) Membrane SUEZ Water Technologies & D.1 DWI 56/4/835
Filtration Module Solutions
ZeeWeed 500ds (350) Membrane SUEZ Water Technologies & D.1 DWI 56/4/835
Filtration Module Solutions

Uncontrolled if printed Page 89 of 89 Issue date: 19 November 2020