Model ATC-1000 3.1 RS-232 Pinout：（DB9 Male） 3.

6 Connection Diagram
TCP/IP to RS232/422/485 Converter （DB9Male） Signal I/O RS-232 Connection
User’s Manual PIN2 RXD IN
PIN3 TXD OUT
PIN5 GND -
PIN7 RTS OUT
PIN8 CTS IN
1.0 Introduction
The ATC-1000 is a cost effective and highly integrated 3.2 RS-422/485 Pinout：（six Terminal from left）
Serial-to-Ethernet Converter. Embedding a 8051CPU, Terminal
1 2 3 4 5 6
64KB OTP ROM, 32K bytes SRAM, 10/100Mbps Ethernet No RS-422 Connection
and serial port support handshake RTS, CTS. ATC-1000 RS-422 T+ T- R+ R- VIN GND
Can control 1 x RS232/422/485 devices located virtually RS-485 485+ 485- - - VIN GND
anywhere (via Ethernet or Internet).
Automatically finds devices in the network Configuration 3.3 Connect to 10/100M：
over Driver Panels, serial Port,Telnet,WEB Browser, ATC-1000 10/100/M Port connect to switcher or HUB use
SNMP Automatic mode switching between Driver and straight-Through Cable
RAW mode Support TCP/IP, UDP, DHCP, PPPoE, Dynamic
DNS.

2.0 Features: RS-485 Connection

¨ 3-in-1 RS-232/422/485 interface Max.230Kbps Serial
interface and 10/100 Mbps Ethernet
¨ Supports 4- and 2-wire RS-485 with AUTO-SEND™ and
built-in terminator
¨ Supports industrial 24 VDC power input and optional Power 3.4 Power Supply：
over Serial
ATC-1000 TCP/IP converter can adopt the product’s 9V power
¨ Terminal block accessories for easy RS-422/485 serial wiring adapter for power supply or adopt power from other DC power or
device.(+9--+24V@500-100mA)。
¨ Supports IP configuration by MAC address
¨ Supports configuration store and copy for easy deployment 3.5 ATC-1000 LED indication ：
¨ Supports Driver, TCP Server/Client, UDP Server/Clie nt, Pair LINK Indication Ethernet Link，Green on Ethernet Link 4.0 Configuration and Operation
Connection operation modes established。 Use this section to set up your computer to assign it a static IP
¨ Easy and powerful configuration program ACT Data Sending/Receiving between Serial and the address in the 192.168.2.2 to 192.168.2.254 range with a
¨ Approval CE, RoHS Ethernet subnet mask of 255.255.255.0. This is necessary to ensure that
3.0 . Hardware Installation & Initial Setup PWR Indication Power your computer can communicate with your ATC-1000. Your
computer must have an Ethernet card and TCP/IP installed. All above the functions explain as below: Subnet mask: default 255.255.255.0
TCP/IP should already be installed on computer using Windows 4.3 Administrator Setup Gateway: default 192.168.2.254
98/2000/XP and later operating systems. Manager of the relevant setting page. Primary DNS: default 192.168.2.253
Step 1：Open your web browser and type http://192.168.2.1 in 4.4 Authentication Configuration If you are connecting through a static or fixed IP from your
the browser’s address box. This address is the factory set IP The Users can change the username and password to prevent network environment, perform these steps ：
Address of your ATC-1000. Press “Enter”. unauthorized access. Step 1: Enter IP address
Step 2：The “ID and Password required” prompt box will Login ID and password authentication, the maximum is 15 Step 2: Enter Subnet mask
appear. Typing “admin” (default username) in the ID field and characters and numbers. Step 3: Enter Gateway IP address
typing “system” (default password) in the Password field. Click User Name: default admin Step 4: Enter Primary DNS IP address
“OK”. The setup screen will then appear. Password: default system Step 5: click Update button
4.6 DHCP
Host Name (Optional): default NETUART, maximum
length 15 characters
If there is a DHCP Server existing in your network
environment or you subscribe a CABLE service from
your ISP, you can set IP configuration to DHCP to get a
dynamic IP address. The Host Name is an optional item,
4.5 System IP Configuration depending on your DHCP Server setting.
The ATC-1000 support three IP connection types: Static IP, 5.0 System Status
User login to enter a password. DHCP. These types are listed in the Web page for the IP This screen shows the ATC-1000’s current status. All of the
Default ID : admin Configuration setting. Each setup screen and available features information provided is read-only.
Default Password: system will differ depending on what kind of IP connection types you Kernel Version: the installed version of the kernel.
4.2 The menu features as below: select. Default is Static IP MAC Address: At present the device MAC Address
Nickname: the product model name of NetUART

5.0 Load default setting

Allow Users to reset the ATC-1000 to return the initial value, but
Static (or Fixed) IP the MAC Address will not be updated.
IP Address: default 192.168.2.1
 Remote Host IP Address: default 210.200.181.102 RS485, The user can reference hardware diagram to directly
If your device is acted as active to report real-time status to select RS232, RS422, RS485, no need select by software.
5.1 Telnet remote and the data be guaranteed to be received by peer is Baud Rate: default 57600, range 300bps to 230.4Kbps
Telnet connection setting: your concern, then you can set ATC-1000 as TCP Client. Be Character Bits: 5, 6, 7, 8 (default)
Telnet Server/Client: Currently used to determine the device is sure the value of item Remote Connection Port Number is Parity Check: None (default), even, odd, space, mark
to the Telnet Server or Client. same as your remote control application using and set the Stop Bits: 1 (default), 1.5 or 2
If the Server, show this connection have to wait for the other correct value of Remote Host IP Address. Hardware Flow Control: None (default), CTS/RTS (or
side of the Port, if the Client, show that external connections to 5.5 UDP Server Hardware)
the Port Local Port Number: default 21, range 0 to 65535 ATC-1000 Management Setup
Remote Server IP Address: When the Client, to be connected If your device is acted as passive to accept commands This chapter will show you how to manage ATC-1000’s
the other side of the server IP Address. from remote and the data be guaranteed to be received access setting as well as configure E-mail alert and
5.2 Operation mode by peer is not your concern, then you can set ATC-1000 firmware upgrade.
The ATC-1000 support four operation mode: TCP Server, as UDP Server. Be sure the value of item Local Port Hi-speed UART the relevant setting, it is basically similar as
TCP Client, UDP Server and UDP Client. These modes Number is same as your remote control application windows
are listed in the Web page for the Operation Mode setting. using.
Each setup screen and available features will differ 5.6 UDP Client
depending on what kind of operation mode you select. Remote Connection Port Number: default 21, range 0 to
Default is TCP Server. 65535
5.3 TCP Server Remote Host IP Address: default 192.168.2.2
Port Number: default 23, range 0 to 65535 If your device is acted as active to report real-time status
If your device is acted as passive to accept commands from to remote and the data be guaranteed to be received by
remote and the data be guaranteed to be received by peer is peer is not your concern, then you can set ATC-1000 as
your concern, then you can set ATC-1000 as TCP Server. Be TCP Client. Be sure the value of item Remote
sure the value of item Port Number is same as your remote Connection Port Number is same as your remote
control application using. control application using and set the correct value of
Client mode inactive timeout (minutes): default 20 Remote Host IP Address.
( 0=Disable)
If you want to keep the connection between ATC-1000 and your
remote control application always on, then set the value of item
Client mode inactive timeout (minutes) to 0, otherwise,
when the inactive time of no any traffic on line reach the setting
value, ATC-1000 will terminate this connection.
5.4 TCP Client
Remote Connection Port Number: default 23, range 0 to 6.0 UART Control (RS-232)
65535 The ATC-1000 support three serial types: RS232, RS422 and