Republic of the Philippines

Department of Education
NATIONAL CAPITAL REGION
SCHOOLS DIVISION OF TAGUIG CITY AND PATEROS
WESTERN BICUTAN NATIONAL HIGH SCHOOL

THIRD QUARTER EXAMINATION IN TLE - COMPUTER SYSTEM SERVICING 9 (JHS)

Grade 9 - Sections 2, 7, 8, 10, 12, 13, 17, 18, 19, OHSP

Name: ______________________________________________ Date: _________________

Grade & Section: ______________________________________ Score: ________________

Directions: Carefully read and understand each statement or question before answering.
Shade the circle that corresponds to the letter of the best answer.

1.) You are setting up a wired network in an office to connect multiple computers, printers,
and other devices for shared internet access and file sharing. What cable would you use
for this setup?
A. Ethernet cable B. Molex C. Power cable D.
SATA
2.) A simple electrical circuit powers a light bulb. What part of the circuit would you identify
as the switch?
A. Conductor B. Control C. Protection D.
Source
3.) Teacher Echo will use an electric circuit device that shows an ON and OFF. What part of
the electric circuit has ON and OFF?
A. bulb B. flow C. fuse D.
switch
4.) Sarah is looking for the definition of electricity as part of her TLE assignment. What is
the best way to describe it?
A. It is the pathway where current flows.
B. It is the flow of electrons or electric current.
C. It is the amount of pulling force that makes the electron flow.
D. It is the opposition to the current flow and measured in ohms.
5.) Roma is watching television while charging his iPhone 14 Promax. After leaving his cell
phone charging, he unplugged the television and turned it off. What kind of circuit
enables the gadget to be unplugged without affecting the other devices' ability to
function?
A. Closed Circuit B. Open Circuit C. Parallel Circuit D.
Series Circuit
6.) Sheena safely manages the exposed wiring while fixing an electric fan. To protect
herself against electrical shock, she chose a material through which electrical current
could flow. What is an example of an electrical insulator?
A. Aluminum B. Copper C. Metal D.
Rubber
7.) A specific voltage for an active device such as a transistor with a particular voltage in the
electric circuit. What electrical component limits or regulates the flow of electrical current
in an electronic circuit?
A. Capacitor B. Inductor C. LED D.
Resistor
8.) An open circuit is a type of circuit that has an open path for current to flow. It means that
current cannot flow in open circuit.? Which of the following is TRUE in the illustration
below?

A. If the switch is “OPEN”, the current can’t flow into the

circuit and the bulb is “OFF”.
B. If the switch is “CLOSED”, the current can’t flow into the
circuit and the bulb is “ON”.
C. If the switch is “OPEN,” current can flow into the circuit,
and the bulb is “ON.”
D. If the switch is “CLOSED”, the current can flow into the
circuit and the bulb is “OFF”

9.) Zia is planning to buy Christmas lights for her Christmas tree, but she is confused about
the circuit she will buy, what kind of circuit connection if the bulbs are connected in a single
electrical path and the current flows through each bulb in order.
A. A closed circuit connection.
 B. An open circuit connection.
C. A parallel circuit connection.
D. A series circuit connection.
10.) Aaliyah is setting up an electrical circuit to function properly, certain requirements must
be met to ensure a complete and safe electrical connection. Which of the following is a
requirement for electrical connections?
A. Right board B. Right screw C. Right terminal fitting D. Right Time
11.) Rian noticed that her microwave is not functioning, she thinks it overheated. To her
knowledge, what safety device protects an electrical circuit from excess current?
A. Cable B. Fuse C. Switch D.
Wire
12.) Teacher Jasper is going to discuss networking cable in his class. He needs a list of
examples of tools and materials for making a network cable. What materials and tools must
be on the list?
A. LAN tester, RJ11, RJ34, and wire stripper.
B. Crimping tool, LAN tester, RJ 45, and UTP cable.
C. Crimping tools, multi-tester, RJ11, and UTP cable.
D. LAN tester, screwdriver, RJ11, and UTP cable.
13.) Joel is working that involves connecting multiple wires to ensure a secure and stable
electrical connection. To join the metal conductors effectively, he needs to use a tool that
melts soldering lead around the connection point. What tool would he use for this task?
A. Crimping tool B. Multi-tester C. Soldering Iron D. Wire Cutter
14.) In grade 9, students are troubleshooting an electrical circuit that appears to have a
restricted current flow. They use a multimeter to measure an amount, and ohms (Ω) is the
unit shown. What is the resistance to current flow in a circuit
A. Current B. Electricity C. Resistance D. Voltage
15.) You are putting together a basic electrical circuit to turn on a little lightbulb. A
component that serves as the electrical energy source must be included to supply energy
for the circuit. Which circuit element is typically represented by a battery or a cell?
A. Fuse B. Load C. Supply D. Switch
16.) In creating a basic electrical circuit. You need to control the fan's on/off timing. Add a
part to the circuit that can control the current flowing from the power source to the fan to
accomplish this. Which component of a circuit regulates the current flowing from the
source to the devices?
A. Connection B. Control C. Protection D. Source
17.) While doing the activity in CSS, JJ is still confused about whether the rj45 is in the
right position. How will he determine the right position?
A. If the last pin of RJ45 is on the left side.
B. If the first pin of RJ45 is facing on the right side.
C. If the first pin of RJ 45 is facing the left side
D. If the opening of RJ45 is away from the user.
18.) Because she previously watched some YouTube tutorials, student Jia has some prior
information about how to use a soldering iron. What does she do first so that she may
show her classmates how to properly melt iron?
A. Cut the hot tip of the soldering gun to the iron.
B. Push the hot tip of the soldering gun to the iron.
C. Pour the hot tip of the soldering gun into the iron.
D. Touch the hot tip of the soldering gun to the iron.
19.) Wire termination or cable termination means properly connecting the ends of the wire
that allow it to connect to a device such as a switch or terminal. Which of the following
electronic components is used in wire termination?
A. Circuit Board B. Conductor C. Insulator D. Transistor
20.) Group 6 students are assembling a circuit. They must guarantee that the electrical
current follows a path. The current moves through the system and will depend on the
circuit components they employ. Which of the following electrical quantities?
A. Battery B. LED C. Switch D. Wire/Cable
21.) Terry is a high school student, she comes to school late, on the day they are
measuring the resistance. What is the first thing that she must do before measuring a
resistance?
A. Set the pointer of the meter to zero (0) Ω.
B Read the scale where the pointer meter rests.
C. Turn the range selector knob to an appropriate Ω range.
D. Connect the test pins to the measured resistance under test.
22.) A simplified drawing of an electrical circuit that uses a solid line to show the conductor
or wires that determine the path of the circuit. What diagram was drawn by using symbols
that represent electrical components?
A. Charges Diagram C. Schematic Diagram
B. Electric Diagram D. Picture Diagram
 23.) Teacher Lyanna and her class are done crimping their cable. For them to know if the
arrangements of cables they will use in networking are correct, what tool would they use?
A. LAN Tester B. Multi-tester C. UTP Tester D. Voltmeter
24.) Ciara is taking an online test involving various electronic components. She needs to
categorize the components based on their functionality. What are the two types of
electronic components?
A. Active and Inactive C. Direct and Indirect
B. Active and Passive D. Inactive and Passive
25.) As the opposition to the flow of current and measured in ohms (Ω) is what you called?

A. current B. electricity C. resistance D. Voltage

26.) Before releasing an innovation, a device maker makes sure to perform a systematic
assessment in which they must confirm the device's operation. What kind of testing is a
formal evaluation or structured examination?
A. Automated Testing C. Inspecting Testing
B. Debugging D. Prototyping
27.) Bea is working with an electrical circuit and accidentally applies the wrong voltage to a
component. What might happen if the applied voltage is incorrect?
A. Led to damage.
B. Finish tasks on time.
C. Ignore the flickering and hope it stops on its own.
D. Use a multimeter to measure the voltage at the socket.
28.) Jon found a capacitor at home to replace the faulty one, what type of test he will use to
identify if it is busted/ broken or still working?
A. Continuity test B. Diagnostic test C. Performance test D. Voltage test
29.) Around Taguig, an electrical engineer is determining problems with a power distribution
line. He suspects that there may be losses or increases in voltage after receiving
complaints regarding electrical equipment. What technique did he employ to find voltage
increases or losses?
A. Continuity test
B. Diagnostic test
C. Performance test
D. Voltage test
30.) An electronic circuit in a household appliance is being troubleshot by a specialist. To
determine the issue, you need to track voltage, current, and resistance. Which test tools will
you use to measure such as voltage and current, using a combination of a voltmeter,
ammeter, and ohmmeter?
A. LAN tester
B. Multimeter
C. Oscilloscope
D. Signal generator
31.) Troubleshooting an electrical circuit and need to identify faults or issues causing it to
malfunction is what type of testing method to detect faults and problems?
A. Continuity test
B. Diagnostic test
C. Performance test
D. Voltage test
32.) In testing electronic components, which of the following steps come first?
A. Test components.
B. Evaluate the testing process.
C. Plan an approach for components testing.
D. Determine criteria for testing electronics components.
33.) The washing machine that Mang Roman fixes isn't working properly. He wants to find
the issue in certain components, like transistors, resistors, and capacitors, work as
expected. Which method is used to control an electrical component's function to identify
whether it is defective?
A. Evaluating B. Planning C. Preparing D. Testing
34.) Alle is diagnosing a computer. He noticed that there was no flow of electricity in the
entire system even if the computer was turning on. What would be the best tool he needs to
troubleshoot his computer?
A. “Crimping tool” C. “Loopback Adaptor”
B. “LAN Tester” D. “Multi-tester”
 35.) Martin is in a center fixing an active server. To replace a component while the device is
still on, one of his coworkers advises taking the power off. If connectors are taken out while
the power is still on, what will happen to the device?
A. Automatic restart C. Malfunction of device

B. Leave your work unfinished. D. Nothing will happen.

36.) Considering whether this method is safe and suitable for the specific application. The
tape-in-together method in wire connection is used to connect two wires.
A. Double-sided tape C. Masking tape
B. Electrical Tape D. Plastic tape
37.) You are tasked to make a circuit in turning on the computer system. Which of the
following preparations should be done first?
A. Check the voltage of electrical sources C. Study schematic symbols.
B. Get all tools and materials needed ready D. Test the circuit
38.) You need to measure the resistance of a resistor in a circuit to determine if it’s
functioning correctly. What is the first thing you must do before taking the measurement?
A. Set your multimeter to the pointer to 0.
B. Adjust the multimeter to the highest voltage setting for safety
C. Ensure the circuit is powered off and completely discharged.
D. Connect the multimeter probes to the resistor while the circuit is powered on.
39.) You are conducting a resistor test using a digital multimeter. While testing the resistor,
the multimeter shows an open pointer (no value, or "OL" for overload). What does this
indicate about the resistor?
A. Has no deflection in any setting.
B. Higher than the allowed resistor.
C. Lower than the allowed resistance.
D. Turn to zero in any setting.
40.) You want to measure the current flowing through a circuit using a multimeter. How
should you connect the multimeter to take an accurate measurement?
A. Connect the multimeter probes to the power supply terminals without regard to polarity
B. Connect the multimeter probes directly across the component, like measuring voltage.
C. Insert the multimeter in series with the component so the current flows through the
meter.
D. Set the multimeter to resistance mode and place it across the circuit to measure the
current.
41.) Grade 11 students are creating an Ethernet cable. They arrange the wires according to
the wiring standard and they prepare to crimp them into a connector. What is the process
they are performing?
A. Cable Crimping
B. Clamping
C. Riveting
D. Soldering
42.) Sometimes it's hard to know a voltage value while measuring the voltage on a circuit.
Setting your multimeter to the proper voltage range and getting ready for the measurement
are the first steps to take. When measuring an unexpected voltage value, which of the
following procedures is followed?
A. Select the minimum range. C. Select the maximum range.
B. Select 250 voltage range. D. Select 50 voltage range.

(For item number 43 – 50) Study the diagram below and answer the following questions.
43.) Based on the illustration above, how many loads are there in the diagram?
A. 2 B. 3 C. 4 D. 5
44.) How many lamps are shown in the diagram?
A. 2 B. 3 C. 4 D. 5
45.) Based on the diagram, what are the names of all the loads that are indicated in the
diagram?
A. Bulb and Fan
B. Fridge and Lamp
C. Fan and Fridge
D. Lamp, Fan, and Fridge
46.) Upon reviewing the picture above, how many switches are shown in the diagram?
A.1 B. 2 C. 3 D. 4
47.) Based on the illustration, what type of diagram does it show?
A. Pictorial B. Schematic C. Technical D. Flowchart
48.) Looking at the illustration above, which component represents the supply or source?
A. circuit breaker B. lamp C. MCB D. socket
49.) In the illustration, which component protects an electrical circuit from damage caused
by overcurrent/overload or short circuit?
A. fridge B. lamp C. socket D. circuit breaker
50.) Does the diagram show a complete circuit? Why?
A. No, because there are no circuit breakers.
B. No, because the components are incomplete
C. No, because there is no flow of electric charges present.
D. Yes, because there is the source of current and it consists of components needed in
a circuit.
 2nd Quarter Exam - TLE 9 – CSS9
(Grade 9 – Sections 2, 7, 8, 10, 12, 13, 17, 18, 19, OHSP)
Answer Key

12
1. A 26. C
2. B 27. A
3. A/D 28. B
4. B 29. D
5. C 30. B
6. D 31. B
7. D 32. D
8. A 33. D
9. D 34. D
10.C 35. B
11. B 36. B
12. B 37. B
13. C 38. A
14. C 39. A
15. C 40. A
16. B 41. A
17. C 42. C
18. D 43. C
19. D 44. A
20. D 45. D
21. A 46. B
22. B 47. A
23. A 48. D
24. B 49. D
25. C 50. D