COLOR TELEVISION

TC1475 / TC2175/ TF2139

TC1475 TC2175 TF2139

 Contents

Contents

1. BRIEF INTRODUCTION...................................................................2

2. ELECTRICAL SPECIFICATIONS.......................................................3

3. STRUCTURE BLOCK DIAGRAM.......................................................4

4. DIAGRAM SCHEMATIC TC1475 / TC2175 .....................................6

5. DIAGRAM SCHEMATIC TF2139......................................................7

6. DIAGRAM PICTORIC TC1475 / TC2175 ..........................................8

7. DIAGRAM PICTORIC F2139 ...........................................................9

8. EXPLODED VIEW TC1475 / TC2175................................................10

9. EXPLODED VIEW TF2139...............................................................11

10. DEFINITION & FUNCTION OF TMPA8873-XXXX PINS...................12

11. REMOTE CONTROL (KEY ASSIGNMENTS LIST).............................15

12. CIRCUIT ANALYSIS.....................................................................16

13. THE T08 CHASSIS MAINLY USE THE FOLLOWING IC AND

ASSEMBLIES ..............................................................................20

14. DESCRIPTIONS FOR THE OPERATION OF FACTORY MODE............21

15. ELECTRICAL PARTS LIST TC1475 ................................................24

16. ELECTRICAL PARTS LIST TC2175.................................................25

17. ELECTRICAL PARTS LIST TF2139 ................................................26

TC1475 / TC2175 / TF2139 1

 Brief Introduction

1. Brief Introduction

TMPA8873-XXXX is introduced in this chassis, controlled by I2C bus, implement

FS PLL tuning.

1 FS tuning 45.75M. band adjustable

2 Tuning in USA channel table by CATV/antenna.

3 Auto tuning, frequency fine tuning, skip setting

4 Color Sys: PAL-M\ PAL-N\ NTSC-M auto identified

5 2 AV input, YUV input, AV1\AV2\DVD(YUV) input preset

6 Switch program by numeric key directly,

7 Picture mode: personal\dynamic\standard\soft, switched by one key

8 Picture parameters adjustment: brightness\contrast\color\ sharpness\hue

9 Mute control: mute when switch programs and AV

10 Power on/off timer, program timer

11 Auto power off 15 minutes later when no signal in TV mode

12 special halftone menu display

13 English\French\Spanish\Portuguese menu display

14 8 self-detect signals generated by CPU for geometry distortion adjustment

15 50HZ/60HZ auto identified

16 Child lock(by press DISP button 4 seconds)

17 AV stereo, 2 volume inner control

18 Color and vertical position of main menu variable

19 Factory logo setting when no signal

20 TA1304/TA1343 tone control Plug-and-Play(25”~34”)

22 Multifunctional RC unit LA7461 TA9028 SC6122 may be efficiency or only

one be efficiency.

TC1475 / TC2175 / TF2139 2

 Electrical Specifications

2. Electrical Specifications

Model Number
RF system PAL-M/N NTSC-M
Video system PAL-M/N NTSC-M
Receiving AIR
channel CATVSTD)

CATVHRC)

CATVIRC)

Channels preset 181

Antenna input 75 Ohm Coaxial Cable
Picture tube 37cm~ 86cm(14” ~ 34” ) diagonal
Audio output 14” 21” : Maximum 2.5W × 2
25” 29” 34” : Maximum 5W × 2
Power source AC90V~ 260VOR AC130~ 260V 50/60Hz
Weight(Approx) 14” (11Kg), 21” (24Kg), 25” (30Kg),29” (38Kg)

Dimensions 14” 450(W)× 410(D)× 378(H)mm

(W× H× D) (Approx) 21” 580(W)× 515(D)× 520(H)mm
25” 750(W)× 528(D)× 560(H)mm
29” 840(W)× 570(D)× 650(H)mm
Power Consumption 14” =65W 21” =75W 25” =120W
29” =130W 34” =150W

Designs and specifications are subject to change without notice.

WARNING
The chassis in this receiver is partially hot. Use an isolation

transformer between the line cord plug and power receptacle, when

servicing this chassis. To prevent electric shock, do not remove cover.

No user-serviceable parts inside. Refer servicing to qualified service

personnel.

TC1475 / TC2175 / TF2139 3

 Structure Block Diagram

3. Structure Block Diagram

Tuner
TU201

SAWF
SIF BTSC
AN5832 or
4053
LA72700

TC4053 AV1
AV SW AV2

TDA1030
TA1304/TA1343
AN7522/AN17821

TDA1030
A1 A2

S-AV y
Vout LA78040/TDA9302
Video Audio LA78041/TDA8177

S Y Cb Cr CRT

FBT
T471
2 in Chip
Hout

TMPA8873-XXXX
EEPROM
8K bit

TA9028-023/022
KEY LA7461
MATRIX RECEIVEERMP SC6122

TC1475 / TC2175 / TF2139 4

 TMPA8873-XXXX Block Diagram

3.1. TMPA8873-XXXX Block Diagram

TC1475 / TC2175 / TF2139 5

 Diagram Schematic

4. Diagram Schematic TC1475 / TC 2175

*Design and specifications are subject to change without notice.

TC1475 / TC2175 / TF2139 6

 Diagram Schematic

5. Diagram Schematic TF2139

*Design and specifications are subject to change without notice.

TC1475 / TC2175 / TF2139 7

 Diagram Pictoric

6. Diagram Pictoric TC1475, TC2175

TC1475 / TC2175 / TF2139 8

 Diagram Pictoric

7. Diagram Pictoric TF2139

TC1475 / TC2175 / TF2139 9

 Exploded View

8. Exploded View TC1475/TC2175

TC1475 / TC2175 / TF2139 10

 Exploded View

9. Exploded View TF2139

TC1475 / TC2175 / TF2139 11

 Definition & Function of TMPA8873-XXXX Pins

10. Definition & Function of TMPA8873-XXXX Pins

CPU part
item definition description
1 DVD high level output in DVD mode
2 NO USE
3 KEY Control signal input; general
keyboard circuit auto identified
4 GND MCU GND
5 REST MCU reset when power on
6 X-TAC
Connect ports for crystal; 20PPM precision required
7 X-TAC
8 TEST For MCU experimentation, connected to GND normal
9 5V Power input for CCD amplitude restricted circuit
10 Vss GND for CCD amplitude restricted circuit
54 GND GND for surge circuit
55 5V Power for surge circuit;
Duty cycle and Ripple voltage less than 10 mV;
56 AV SW Multi-control level output 2 or 3 TV/AV mode
57 SDA SDA input
58 SOL SCL input
59 50/60HZ Low level when 50HZ
High level when 60HZ
60 NO USE
61 MUTE MUTE control
62 NO USE
63 RMT IN
RC unit signal input
Power control; low level for initialization; related with
64 Power
item ONTIME of Page F11

Note for control port output state: (in the output table below,”0”for low level, “1” for high
level)

Pin3 Description:
Voltage range for each button (middle value is suggested)

KEY Off P+ P- V+ V- MENU TV/AV POWER

Range 0V ≤ 1.16V ≤1.74V ≤ 2.45V ≤ 3.17V ≤ 3.88V ≤ 4.60V ≤ 5V

0≤
Range 5V ≤1.02V ≤1.74V ≤ 2.45V ≤ 3.17V ≤ 3.88V ≤ 4.60V
0.45V

TC1475 / TC2175 / TF2139 12

 Definition & Function of TMPA8873-XXXX Pins

Pin6, Pin7 less than 20PPM precision required for crystal

Duty cycle and Ripple voltage of power for Pin55 must less than 10 mV;
power for OSD clock)

Pin56 AV/TV switch

TV AV1/S/DVD AV2 Connect way
OPT.2=0 0V 0V 5V Pull up resistance
connected to 5V
or 8V
10K pull up
esistance connected
OPT.2=1;OPT.5=0 0V 2.5V 5V to 5V and 10K pull
down resistance
connected to GND

10K pull up
OPT.2=1;OPT.5=1 0V 5V 2.5V resistance
connected to 5V

Pin59 50HZ/60HZ switch

Pin59 NTSC(60HZ) PAL(50HZ)
voltage 5V 0V

Pin61 Mute 1K pull up resistance

Pin64 Power
a) RC, Pin61\64 wave: Power on
power off

Power

Mute

Power off

Cold
Switch
power on
program
Mute

TC1475 / TC2175 / TF2139 13

 Definition & Function of TMPA8873-XXXX Pins

Mute setting
0 Not mute in no signal TV mode
when no blue background,
MODE2.0
1 Mute in no signal TV mode
when no blue background
0 Mute in no signal AV mode
when no blue background
MODE2.1
1 Not mute in no signal AV mode
when no blue background

Signal transacting part:

11 TV GND Analog GND
12 FBP-IN Input port for flyback pulse
13 H-out Output port for horizontal driver pulse
Connect port for horizontal AFC filter
14 H-AFC
The voltage of this port control the frequency of H-VCO
Connect capacitor for SAW generating,
15 V-SAW The amplitude of SAW is a constant because of the
controlling of V-AGC
16 V-out Vertical driver pulse output
17 H-Vcc 8V power for deflection
18 TV GND Analog GND
19 Cb Input port for Cb signal
20 Y-IN Input port for Y signal
21 Cr Input port for Cr signal
22 EXT-AU1 AUDEO1 input
23 C-in Input port for C signal
24 V2 Input port for CVBS/Y signal
25 ACL Interface for ACL filter
26 TV-in Input port for TV video signal
27 ABC-in ABCL input
28 Audio-out1 Port 1 for audio output with volume control function
29 Audio-out2 Port 2 for audio output with volume control function
30 TV-out PIF demodulation signal(full TV signal) output
Sound intermediate frequency output(may no periphery
31 SIF circuit)
32 EXT-AU2 AUDEO2 input
Second sound intermediate frequency or horizontal phase
33 SIF in emendation signal input
34 DC NF Connect with capacitor

TC1475 / TC2175 / TF2139 14

 Remote control (key assignments list)

35 PIF•PLL Connect with PIF-PLL filter

36 IF-5V 5V power for IF
37 S-Reg Connected with filter capacitor, stabilization inner bias
38 AU OUT Audio output, not with volume control
39 IF AGC Connected with AGC filter
40 IF GND IF GND
41 IF in Pin41Pin42 are input port for differential amplifier,
42 IF in input IF signal from SAW
43 RF AGC RF-AGC signal output for tuner
44 Black Det Connected with black detect filter
45 Monitor out CVBS/SVM output, CVBS/SVM selected by I²C
46 APC fil Connected with APC filter of chroma decode circuit
47 YC VCC5V1 Power for YC
48 SYNC OUT SYNC output
49 DVCC 3.3V Power for digital circuit
50 R out R output
51 G out G output
52 B out B output
53 GND Connected with analog GND

11. Remote control (key assignments list)

ico function data 9028-0E0E LC6122 7461-54H7 7461-55K2

(D7-D0) H E X BF40 H E X H E X
1 00000000 00 00 1 1
2 00000001 01 01 2 2
3 00000010 02 02 3 3
4 00000011 03 03 4 4
5 Number key 00000100 04 04 5 5
6 00000101 05 05 6 6
7 00000110 06 06 7 7
8 00000111 07 07 8 8
9 00001000 08 08 9 9
0 00001001 09 09 0 0
-/-- 00001010 0A 0A 0a 0a
POWER Standby key 00001011 0B 0B 0x12 0x1C
BTSC BTSC key 00001100 0C 0C 0x1f 0x0d
P.P Picture mode key 00001110 0E 0E 0x19 0x13
TV/AV TV/AV key 00001111 0F 0F 0x0B 0x0f
P- Channel lessen key 00010000 10 10 0x17 0x1a

TC1475 / TC2175 / TF2139 15

 Circuit Analysis

P+ Channel add key 00010001 11 11 0x13 0x1b

Vol- Volume lessen key 00010010 12 12 0x14 0x1e
Vol+ Volume add kye 00010011 13 13 0x10 0x1f
MUTE Mute key 00010100 14 14 0x16 0x15
SLEEP Sleep key 00010101 15 15 0x0f 0x19
DISP/LOCK Display/lock key 00010110 16 16 0x1b 0x14
RECALL RECALL key 00010111 17 17 0x1a 0x0e
MENU Menu key 00011100 1C 1C 0x0e 0x10
PIC Picture menu key 0001101 1D 1D 0x1c 0x0c
SOUND-MODE SOUND-MODE key 00011110 1E 1E 0x1d 0b
D-MODE Factory key 00101100 2C 2C 0x11 0x1d

12. Circuit Analysis

12.1 Tuning circuit
Buildup by frequency synthesized, PLL tuning, controlled by I2C bus tuner
and some individual components. Tuning process controlled by correlation
pins of UOC TMPA8873-XXXX. Pin57 & pin58 of CPU output I2C tuning
data for SCL & SDA of tuner.
FS tuner introduced in this chassis, cooperate with SCL & SDA data from
pin57 & pin58 of N101, processing FS auto tuning. 33V for tuner supplied
by 110V(130V), divided by R518 and stabilized voltage by N505.
Frequency synthesized fashion is also called PLL frequency synthesized
fashion. It is the CPU controlled by channel subscribe program band
switch and data from RC receiver and give the band switch signal. CPU set
frequency divide ratio for variable frequency divider of PLL. Variable
frequency divider dividing the local oscillation frequency from tuner and
compare the phase with benchmark frequency, adjust local oscillation
frequency accord with the local oscillation frequency needed by each chan-
nel.
12.2Picture IF circuit
The IF signal from tuner enter into SAW filter Z101(F45C) after amplified by
Pre-Amp built up by V103 and so forth, filtered accordance with IF characte-
ristic and enter TMPA8873-XXXX and output PIF demodulation
signal(CVBS) from pin30, pass through the emitter follower buildup by R155
R156 V104 R158, coupled to pin26 (inner switch)of TMPA8873-
XXXX by C147.

TC1475 / TC2175 / TF2139 16

 Circuit Analysis

12.3. Sound processing

The SIF2, come from inner phase lock demodulate of TMPA8873-XXXX,
turned into audio signal after limiting amplifier and frequency discriminator.
Two audio signal, out of pin28 & pin29 of TMPA8873-XXXX, enter pin9 of
N681 & N691 separated and audio power amplified. They are used to driver
speakers separated after output from pin16 of N681 & N691.
12.4Periphery AV input processing
Periphery AV1V1 L1 R1 input from pin5 pin 12 pin 2 of N801
TC4053 separated. Periphery AV2 V2 L2 R2 input from pin3pin
13 pin1 of N801 TC4053 separated. The level output from pin56 of
N103 control the switch of N801. The video signal, output from pin4 of
N801, transmitted to inner of TMPA8873-XXXX by pin24 of N103 after swit-
ched. The audio signal, output from pin14 & pin15 of N801, transmitted to
inner of TMPA8873-XXXX by pin24 of N103.
12. 5Line scan
Inner synchronize separate included in TMPA8873-XXXX, build up by VCO
surge circuit, line frequency divider, AFC circuit, line output driver. Line
driver signal output from pin13 of TMPA8873-XXX, amplified by V431
(2SC2383) at line-excited level and then amplified by V432 at line output
level.
T471 is the FBT. Volts d.c. +110V21” +135V 29” enter it through
pin4. Line flyback pulse divided into two routes: one for heater (virtual value
6.3V) and one for FBP of AFC after through R405 and stabilized voltage by
VD408 (9.1V). Pulse output from pin10 of T471 rectified by VD447 and filter
by C447 and we get +180V for Pre-Amp as power supply. Pin9 of FBT is
ABL , used as input of pin27 of TMPA8873-XXXX.
12.6. Field scan
Field output level buildup by CD78040/LA78041(N451) and its periphery
components.
Field synchronization signal enter into saw wave produce circuit after
synchronization separate. Pin16 of TMPA8873-XXXX output field saw wave
driver signal to pin1 of CD78040/LA78041by pass R451, and it is output
from pin5 after driver amplified and output power amplified at the inner of
CD78040/LA78041(N451). C450 R454R453 R461A/B are field
feedback components for improving filed linearity and stabilizing the field

TC1475 / TC2175 / TF2139 17

 Circuit Analysis

work point. Field feedback signal enter pin7 of LA7841. VD451 C451
buildup a bootstrap rise voltage circuit. The power supply for pin6 of LA7841
is 26V during scan time and bootstrap rise voltage to 48V during flyback
time. In this way, the work efficiency of field output level is improved and
also the voltage of power supply for pin7 will not less than the pulse amplitu-
de of pin5 during flyback, and eliminate retrace efficiency accordingly. By
the way, if the linearity of scan is not well, it is something wrong with boots-
trap rise voltage circuit commonly.
12.7. H-PARAB emendation circuit:
The principle of H-PARAB emendation is to using field parabolical wave to
modulating amplitude of horizontal scan current. The current accretion
according to parabolical wave rule during electron beam scan the middle of
screen and so on the H-PARAB raster turned into rectangle raster.
12.8. Color driver
Tricolor signal amplified by tricolor driver. The white balance adjustment of
this chassis completed under the control of I2C bus.
12.9. Power supply
1 A3 power supply: The power supply of this chassis adopt self-excitation
pulse transformer coupling switch power. It’s very steady because of the
photo-electricity transfer component adopted for stabilized voltage sam-
pling.
1 Power supply analyses
ARectifying
A.C. 220V is delivered to bridge rectifier circuit buildup by VD503~VD506
after filted by noise filter composed by L501R501C501 C502, and
transformed to 300V D.D. voltage after filted by L502 C507 and powe-
red supply for collector of V513 by elementary coil of switch mode trans-
former T511.
B Oscillator circuit
Self-excitation oscillator circuit buildup by switch transistor V513 and
switch-mode transformer T511, and the error sampling circuit buildup by
R552~R554RP551VD560 V533 N501.
CStabilized voltage
Photo coupler N501 buildup by a LED and a photo trail-transistor. The
work state of photo trail-transistor controlled by the light emitted by LED.

TC1475 / TC2175 / TF2139 18

 Circuit Analysis

The voltage controlling LED get from 110V/130V by sampling circuit

buildup by R552~R554 RP551VD560 V553. The voltage from
collector of V553, connected with the LED negative inner
N501,controlling the light emitted by LED.
DRectifier and Filter Circuit
Switch-mode transformer T511 supply different working voltage for
chassis by its 4 secondary windings and separate the power supply of
chassis from mains supply..

2 WIDE POWER 90V~260VIC-W65XX Introduction

A W65XX Block diagram(Connection diagram)

TC1475 / TC2175 / TF2139 19

 TMPA8873-XXXX

B Functions of Each Terminal

Terminal
Symbols Descriptions Functions
No.

1 D Drain terminal Mosfet Drain

2 — — —

3 S/GND Source and Ground terminal MOSFET Source and Ground

4 Vcc Power supply terminal Input of power supply for control circuit

Soft-Start and Over-current protection Adjustment of over-current protection and Soft

5 SS/ADJ
adjustment Terminal Start Operation Time set up
Constant Voltage Control Signal Input and
6 FB Feed back terminal
Burst(intermittent)mode Oscillation Control
Bottom Detection Signal Input and External
7 BD Bottom Detection Terminal
Latch Signal Input

13. The T08 chassis mainly use the following IC and assemblies
114~21”(AC90~260V)

NO. Position Type Function De scription

1 N103 8873 CPBNG XXX Controller and small signal processor
2 N102 ATME24C08 EEPROM
3 N801 HM14053N Analog swtich
4 N451 CD78040/LA78040 Vertical scan output stage circuit
5 N681 N691 TDA1030 Audio processor

6 N502 STR -W6553A Power supply cir cuit

7 TU201 ET-5C511 -M04 Tuner

2 25~34”(AC90~260V)
NO. Position Type Function Description
1 N101 8873CPBNGXXX Controller and small signal processor
2 N102 ATME24C08 EEPROM
3 N801 HM14053N Analog swtich
4 N451 LA78041/TDA8177 Vertical scan output age
st circuit
5 N701 AN7522/AN17821 Audio Amplifier
6 N502 STR-W6556A Power supply circuit
7 TU201 ET-5C511-M04 Tuner
8 N601 TDA1343/TDA1304 Audio Processor

TC1475 / TC2175 / TF2139 20

 Descriptions for the operation of factory mode

14. Descriptions for the operation of factory mode

14.1. How to enter the factory mode:

A Use remote control
Press panel Volume down (V-) key of the TV set to lower the volume to
0(don't release it) while pressing the display key of the remote unit to enter
debug menu of factory mode
B Use factory remote control
Press“FAC”key, goes to the debug menu of factory mode directly
2 How to exit from factory mode
A Use remote control
1 Press ”DISP” key, then TV system will exit from the factory debug
menu status to normal status
2 Switch off the power supply and power on, then TV system will exit
from the factory mode and goes to normal status
B Use factory remote control
Press FAC” key, then TV system will exit from the factory debug menu
status to the factory aging mode, Press “FAC” key again, system will go
to normal status.
14.2Direct key function descriptions for factory mode, In factory mode,
some keys function will be changed to factory function key for
debugging.
1 Mute Key Page Up for factory mode menu
Return Key Page Down for factory mode menu
“CH+ CH-” Key Select the item of menu
“VOL+ VOL-” Key Modify the data
2) Press “-/--” Key V Stop function will implement and shows a horizontal
line for the white balance adjustment.
“1” Key R-CUT increase
“4” Key R-CUT decrease
“2” Key G-CUT increase
“5” Key G-CUT decrease
“3” Key B-CUT increase
“6” Key B-CUT decrease

4 Press“DISP”key, 4 kind of test signal will be displayed on the screen.

TC1475 / TC2175 / TF2139 21

 Descriptions for the operation of factory mode

14.3. Items on page F0~F5

F 0 NTSC Geometr adjust not for PAL
Items Description Recommend Data Max
NT.H.PHASE Horizontal Phase for 60Hz system 19 31
NT.V.POSI Vertical Phase for 60Hz system 01 15
NT.V.SISE Vertical Amplitude for 60Hz system 28 63
NT.V.LIN Vertical Linearity for 60Hz system 15 31
NT.V.SC V-S correction for 60Hz system 15 31
NT.HBOW H Bow correct for 60Hz system 04 07
NT.HPARA Parallelogram correct for 60Hz system 04 07
H.BLK.LEFT Horizontal Left vanish 0 07
H.BLK.RIGHT Horizontal Right vanish 0 07

F 1 PAL Geometr adjust offset refer to NTSC only for PAL signal

Items Description Recommend Data Max

H.PHASE Horizontal Phase for 50Hz system 0 -11~10
V.POSITION Vertical Phase for 50Hz system 0 -11~10
V.SIZE Vertical Amplitude for 50Hz system 0 -11~10
V.LIN Vertical Linearity for 50Hz system 0 -11~10
V.SC V-S correction for 50Hz system 0 -11~10
HBOW H Bow correct for 50Hz system 4 -8~07
HPARA Parallelogram correct for 50Hz system 4 -8~07

F 2 Broghtness balance adjust

Items Description Recommend Data Max

RC Red cut 32 255
GC Green cut 32 255
BC Blue cut 32 255
GD Green driver 60 127
Blue driver 72 127
SB Sub Brightness 00 63
D

TC1475 / TC2175 / TF2139 22

 Descriptions for the operation of factory mode

F3 Sub-Contrast Sub-Color and OSD adjustment

Items Description Recommend Data Max

SUB.CONT Sub-contrast 12 15
SUB.COLOR Sub-color 10 127
ST3 TV NTSC3.58 high frequency advance degree 37 63
SV3 AV NTSC3.58 high frequency advance degree 37 63
ST4 TV PAL4.43 high frequency advance degree 37 63
SV4 Other AV system high frequency advance degree 37 63
SVD DVD high frequency advance degree 37 63
OSD.CONT OSD contrast 1 15
OSD.H.POSI OSD horizontal position 16 127
OSD.V.POSI OSD vertical position 32 127

F4: Language adjustment

Items Description Recommend Data Max

ENGLISH ENGLISH 01 01
FRENCH FRENCH 01 01
SPANISH SPANISH 01 01
PORTUGUESE PORTUGUESE 00 01

F5 AGC Tuner BAND adjustment

Items Description Recommend Data Max
RF.AGC Automatic gain control 35 63
MENU1 Color option for tool bar of menu 13 15
MENU2 Translucence color option of mene 8 15
VHL VHL BAND 39 79
UHF UHF BAND 127 127
POWER 0 Standby 1 open 2 menory 2 2
PAGE Sub –menu of factory mode 00 01

TC1475 / TC2175 / TF2139 23

 Electrical Parts List

15. Electrical Parts List TC1475

MODEL PART NUMBER PHOTO DESCRIPTION SPECIFICATION

CPU
INTEGRATED
05-8873CS-C10 IC 8873CSCNG6UP3
CIRCUIT
CONTROL

TUNER
34-457FF5-N01-2 TUNER
ET-5C511-M04

FBT
HIGH VOLTAGE FBT
19-F00010-000-D
FLY-BACK BSC24-01N4010GV
TRANSFORMER

POWER IC
POWER IC
03-0W6553-AA0 PWM
STR-W6553A
REGULATOR

HORIZONTAL HORIZONTAL
03-SD1555-0A0 OUTPUT TRANSISTOR
TRANSISTOR 2SD1555
TC1475

MEMORY IC
05-T24C08-U10 MEMORY IC
08B(AT24C08B-PU)

40-03150D-1GT-6 FUSE Fuse T3.15AL250VAC

81-09016W-000
SPEAKER 8 OHM / 5W

RS09 REMOTE
REMOTE CONTROL MTI
81-09016W-213
CONTROL 8891-1002 (Parker)
8873-6UP3

Chassis Parker
CHASSIS
TC1475-14E2A TC1475
PCB MAIN
8873-6UP3

TC1475 / TC2175 / TF2139 24

 Electrical Parts List

16. Electrical Parts List TC2175

MODEL PART NUMBER PHOTO DESCRIPTION SPECIFICATION

CPU
INTEGRATED
05-8873CS-C10 IC 8873CSCNG6UP3
CIRCUIT
CONTROL

TUNER
34-457FF5-N01-2 TUNER
ET-5C511-M04

FBT
HIGH VOLTAGE FBT
19-F00080-000-D
FLY-BACK BSC24-01N4006EV
TRANSFORMER

POWER IC
POWER IC
03-0W6553-AA0 PWM
STR-W6553A
REGULATOR

HORIZONTAL HORIZONTAL
03-SD1555-0A0 OUTPUT TRANSISTOR
TRANSISTOR 2SD1555
TC2175

MEMORY IC
05-T24C08-U10 MEMORY IC
08B(AT24C08B-PU)

40-03150D-1GT-6 FUSE Fuse T3.15AL250VAC

81-09016W-000
SPEAKER 8 OHM / 5W

RS09 REMOTE
REMOTE CONTROL MTI
81-09016W-213
CONTROL 8891-1002 (Parker)
8873-6UP3

Chassis Parker
CHASSIS
TC2175-21E2A TC2175
PCB MAIN
8873-6UP3

TC1475 / TC2175 / TF2139 25

 Electrical Parts List

17. Electrical Parts List TF2139

MODEL PART NUMBER PHOTO DESCRIPTION SPECIFICATION

CPU
INTEGRATED
05-8873CS-C10 IC 8873CSCNG6UP3
CIRCUIT
CONTROL

TUNER
34-457FF5-N01-2 TUNER
ET-5C511-M04

FBT
HIGH VOLTAGE FBT
19-F00080-000-D
FLY-BACK BSC24-01N4006EV
TRANSFORMER

POWER IC
POWER IC
03-0W6553-AA0 PWM
STR-W6553A
REGULATOR

HORIZONTAL HORIZONTAL
03-SD1555-0A0 OUTPUT TRANSISTOR
TRANSISTOR 2SD1555
TF2139

MEMORY IC
05-T24C08-U10 MEMORY IC
08B(AT24C08B-PU)

40-03150D-1GT-6 FUSE Fuse T3.15AL250VAC

81-09016W-000
SPEAKER 8 OHM / 5W

RS09 REMOTE
REMOTE CONTROL MTI
81-09016W-213
CONTROL 8891-1002 (Parker)
8873-6UP3

Chassis Parker
CHASSIS
TF2139-21E2A TF2139
PCB MAIN
8873-6UP3

TC1475 / TC2175 / TF2139 26