FAQ/Contact us
Products FAQs
Aluminum electrolytic capacitor Reliability
NIPPON CHEMI-CON CORPORATION Site Map Company/IR EN
Product Search/ Products Lineup Design Tools Downloads FAQ/Contact us
Purchase Samples
Aluminum Electrolytic Capacitors Lifetime and Reliability Category
Aluminum Electrolytic Capacitors
For designing the device with aluminum electrolytic capacitors, a failure rate and useful life are necessary to be
considered for their reliability. The failure rate of aluminum electrolytic capacitors is approximated by the bathtub curve Multilayer Ceramic Capacitors
shown in (Fig.17).
Supercapacitors
Metal Oxide Varistors
Inductors (Coils)
Camera Module
Wafer
Module
All Products
Tags
【Fig.17】Bathtub curve
AEC-Q200 Automotive
Formula
ⓐ Early failure period
FrequencyCharacteristics
At the comparatively early periods of use, devices/components fail by deficiencies in design or manufacturing process or
incompatibility with operation conditions. For aluminum electrolytic capacitors, these defectives are removed by Introduction LifeTime
debugging at one of manufacturing processes before shipments
Package
ⓑ Random failure period PartNumberingSystem
Failure is stable low in occurrence and appears unrelated to their served term. Aluminum electrolytic capacitors are low
Precaution
in catastrophic failures in this period compared with semi-conductors and solid tantalum capacitors
ProductionProcesses
ⓒ Wear-out failure period
SafetyStandard Soldering
In this period, the failure rate increases with the served time. For aluminum electrolytic capacitors, since they were
completed in manufacturing, the electrolyte impregnated has gradually evaporated and diffused out of the capacitors Storage TechnicalTerm
through the rubber seal materials with time, which leads to decrease in the capacitance and/or increase tanδ. When any
applicationexamples
of these values changes beyond the allowable range of specifications, the capacitors are defined as “fell into the wear-
out failure”. The served term until the capacitors fall into the wear-out failure period is called a useful life. automotive formula
lifetime malfunction
Aluminum electrolytic capacitors have two categories of failures: catastrophic failure and wear-out failure materials members
precaution
<Catastrophic failure>
This is a failure mode that completely destroys the function of the capacitor such as short circuit and open circuit failure. productintroduction
productionprocesses reflow
<Wear-out failure>
safetystandard soldering
This is a failure mode where the electrical parameters of the capacitor gradually deteriorate and fail. The criteria for
determining if this failure has occurred depend on the purpose of a device. For each series of capacitors, the following standardization storage
electrical parameters have been defined as criteria in the specifications of Endurance in the catalogs or product
technicalterm
specifications:
・Change in capacitance
・Tanδ
・Leakage current
Failure rates are often measured in units of % per 1000 hours (10-5/hour). For higher reliability devices designed with a
smaller failure rate, units of Failure In Time (FIT) (10-9/hour) is used.
Aluminum electrolytic capacitors are considered as components of wear-out failure mode, the electrical characteristics
of which gradually deteriorate and their failure rate increases with time. In general, the failure rate in FIT is determined
by total componenthours (product of the number of tested components and test hours).
Due to the definition of FIT, the same FIT rate can be calculated in both cases of testing on the large number of tested
components and also testing for long test periods of time. However, these cases mean differently for aluminum
electrolytic capacitors. Using the failure rate is not suited to express the reliability of aluminum electrolytic capacitors,
but the electrical characteristics based lifetime in hour should be considered to express the reliability.
Also, there are MTBF (Mean Time Between Failures) and MTTF (Mean Time To Failure) to express reliability. The latter is
applicable for aluminum electrolytic capacitors because they are categorized into a group of non-repairable systems,
equipment and devices for which MTTF is applicable.
If you have any questions or inquiries that do not apply to the above, please contact us at the following address.
Products Inquiries
Home / FAQ/Contact us / Aluminum Electrolytic Capacitors / Aluminum electrolytic capacitor Reliability
Products Lineup Company/IR
Product Search/Purchase Samples Aluminum Electrolytic Capacitors Multilayer Ceramic Capacitors News
Film Capacitors Supercapacitors Metal Oxide Varistors Company
Inductors (Coils/Cores) Camera Module Wafer Sustainability
Module Investor Relations
Material Procurement
Design Tools Distributors
Lifetime Estimation SPICE/S parameters in US
3D-CAD Application guides in Europe
Reliability test data
Downloads
FAQ/Contact us
Products FAQs Products Inquiries
Site Terms of Use Privacy Policy Social Media Policy Cookie Policy Site Map © Nippon Chemi-Con Corporation. All rights reserved.
We use cookies on our website to provide appropriate and comfortable services to you. For more
I accept cookies I refuse cookies
information, see our Privacy Policy and Cookie Policy.
